Used Fliegl Special Agricultural Machinery for sale (301)

Condition: new, machine/vehicle number: f79a9f15e7131d57a512793ab, empty load weight: 8,900 kg, maximum load weight: 15,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Widenings extendable to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing rings at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical incl. axle load compensation front and rear Axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Front offset with steel/ checker plate covering Then with 70 mm softwood floor, steel/checker plate covering in the wheel arch area Cjdpsi Ri Izsfx Ahysrk Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Operating instructions With 10,000 kg axle load, a special permit is required, only indivisible load possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany With Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Incl. Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized

Condition: new, machine/vehicle number: 5c7120ea17bcf92d3b69899da, empty load weight: 14 kg, maximum load weight: 35 kg, overall weight: 50 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with exchangeable 2 king pins 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2x wheel chocks with holder Aluminum side collision protection Quarter-shell mudguards in front of and behind axle unit with spray flaps behind each axle 1x storage box Box, w=2 350 mm x l=730 mm x h=640 mm, bolted transversely at the front to the floor of the gooseneck, with 2 storage trays Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks on gooseneck, front transverse Wooden planks 70 mm for widening to 3000 mm Excavator trough above the rear axles starting to the rear, approx. 500 mm wide and approx. 230 mm deep Low loader lashing eyes 3 pairs of lashing eyes per 10 tons at the front gooseneck, 8 pairs of lashing eyes per 10 tons in the low bed, 3 pairs of lashing strips in the tramline area of the low bed, 3 pairs of lashing eyes per 10 tons in the axle/rear area Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Hydraulic forced steering via saddle deflection wedge acting on all 3 axles, Post-steering with radio remote control + auto toe-in, (up to max. 20 km/h)Note! A 2-pin Nato socket with at least 2 x 35 mm² is required in the truck for the power supply to the steering system. Power is supplied to the pump unit via a Nato connection cable to the towing vehicle, without truck installation (re-steering must be used once a week). Air suspension Cedsi Ri Hgopfx Ahysrk Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, without connecting cable With lifting & lowering valve, hold function in lowering position + auto-reset function Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle driving stability system Trailer Infocenter, for displaying vehicle data such as axle loads (no calibrated scales), mileage and diagnostic/system messages. Electrics 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white LED position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1x additional LED work light(s) at the rear, switched via reversing light 1x LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Gooseneck with steel / checker plate covering In the tramline area with 70 mm softwood floor, in the wheel housing area with steel / checker plate covering, low bed can be raised hydraulically on the left and right in the tramline area for entry, via truck auxiliary drive Rear slope with 70 mm softwood floor Drop deck length approx. 6,300 mm Drop sides 25 mm aluminum h

Condition: new, machine/vehicle number: d461243f559015adca5bb372c, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco, Knorr or Haldex Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Csdoi Ri Dlopfx Ahysrk Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: used, machine/vehicle number: 266c1faf254aacf5bd0b3713c, empty load weight: 2,400 kg, maximum load weight: 11,000 kg, overall weight: 13,400 kg, axle configuration: 2 axles, first registration: 03/2014, tire size: 285/70 r19,5, Year of construction: 2014, Further information Fine-grained steel welded construction, fifth wheel coupling, make of our choice for 2\ kingpin with ball bearing slewing ring, stop max. 20°, telescopic support foot, 2 wheel chocks with holder, steel underride guard, half-shell mudguards CLG under-coupler drawbar with tested 50 mm drawbar eyes to the dolly and to the motor vehicle. Crodpfxoi Rizme Ahyok BPW disc brake axles, air suspension with lift & lower valve 2-line compressed air brake system, spring-loaded parking brake, Duomatic front coupling head, with connecting lines to the tractor unit2 interchangeable coupling heads to the trailer EBS, electronic braking system with EBS plug at the front, with connecting cable, Can RouterEBS connecting cable to the trailer, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load detection for trucks via EBS, without truck instal. 24 volt, multi-chamber LED lights, amber LED lighting at the sides, 2 white LED position lights at the front 2 white/red rear lane departure warning lights in LED, 1 x 15-pin plug at the front, with connecting cable to the truck 1 x 15-pin plug with connecting cable to the trailer, cable routing for camera system Country of registration: Germany, with Dekra approval, prepared for single-line license plate holder, contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Saddle height approx.: 1150 mm

Condition: new, machine/vehicle number: 7383bc2b7f580f0cb319b52f7, empty load weight: 5,300 kg, maximum load weight: 29,700 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Surface stone-repellent Splash guard behind last axle in asphalt version, attached to mudguard with hinge, with attachment option on top of mudguard, shortened mudguard Tow hook at the rear Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics High-pressure cylinder max. 250 bar, with HDK screw socket, fixed part, NW 48 mm (without hose connection) Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Membrane rear wall Rear wall as pendulum flap, resting on the outside with 2-fold hook locking. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Insulated body, Fliegl Asphalt Profi Thermo, body insulated at the front, sides, bottom and rear with Fliegl Isotherm. BASIC cover, tarpaulin cladding Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Credoi Rix Ijpfx Ahyek Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) Body strength according to EN 12642 24/7 service hotline Manufacturer certificate for thermal vehicles according to RS 10 - 2013 Prepared for single-line license plate holder Contour marking

Condition: new, machine/vehicle number: d7a33d709a92cd60f18d010e8, empty load weight: 3 kg, maximum load weight: 14 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 385/65 r22.5, Further information Chassis Wechel central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 1 pair of front gear support legs, with straight lower section and single-sided operation in FR right 2 wheel chocks with holder Aluminum side impact guard Side collision protection set inwards, for optimum clearance to the swap body supports Steel underride guard Half-shell mudguards Spray flaps Towing device central axle trailer Drawbar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or precise testing still required in the event of an order) Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Air supply 208 liters Crodji Riwbopfx Ahyok Spring-loaded parking brake 2 swap-proof coupling heads at the front, with connecting lines to the engine trolley, connection in FR right-hand side EBS, electronic brake system with EBS plug at the front, with connecting cable, connection in FR right-hand side Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in both lowering / lifting position Wheels and tires 385/65 R22.5 Athos brand Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin plug at the front, with connecting cable, connection in FR right-hand side 2 additional LED work lights, integrated at the rear, switched via reversing light 1 LED work light at the front, centered between the carriers, radiating to the rear, switched via reversing light Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Attention: Archive pictures!

Condition: used, machine/vehicle number: 5a722b71e07e463c6c5370ad2, empty load weight: 6,927 kg, maximum load weight: 28,073 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 07/2016, tire size: 385/55 r19,5, Further information Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Note! With a frame neck height of 30 mm, the truck wheelbase must not exceed 3700 mm! Outer frame slightly slanted with Load-Lock profile for attaching lashing strapsNote! To attach the straps in conjunction with drop sides, the drop sides must be opened! Not in the neck area! 10 pairs of additional lashing eyes embedded in the outer frame, 2.5 tons each, outer frame with Load-Lock profile for attaching lashing strapsNote! Cannot be used with drop sides! 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation, folding supports at the front in front of the bulkhead can be extended outwards and folded down. Moved inwards as far as possible when driving. (for unhitching under load), without supports, pull-out ladder at the rear, door locks at the side, wheel chocks with holder, aluminium side collision protection, galvanized steel underride guard, quarter-shell mudguards in front of the first axle and behind each axle, with anti-spray flaps behind each axle, rear impact protection Heavy blocker rear transverse impact protection, heavy-duty pallet stop on both sides, approx. 20-25 mm high, with lashing option every 200 mm, loading height reduced by approx. 20-25 mm, plastic toolbox SAF disc brake axles, air suspension, without lift axle 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable front coupling heads, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, vehicle stability system 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front 2 white/red lane departure warning lights at the rear, 2 x 7-pin and 1 x 15-pin interchangeable sockets at the front, without connecting cable Floor: Front area steel floor with anti-slip coating, screen printing plates approx. 30 mm thick, cross joints with Omega inlay, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg, steel/ checker plate covering in the wheel area. Front bulkhead/front stanchions: 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, bottom inside at approx. 140 mm height with steel impact protection Middle stanchions: 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and long pocket at the bottom, 3 pairs of stanchion positions, aluminum insertion slats Rear steel corner stanchions up to lower edge of roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf with 2 internal espagnolette locks each Crodekyrlwepfx Ahyok Tarpaulin with welded-in horizontal and vertical straps, stainless steel tensioning fasteners, customer lettering on rear portal Roof: sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-roof rail for automotive industry, internal width between the roof rails approx. 2,490 mm, tarpaulin color: white, EcoLift - lifting roof can be raised by approx. 380 mm, with gas pressure damper support, anti-ice system, with a hose in the middle, with automatic ventilation Approval country: Germany, test approval according to EC 2007/46, load securing certif

Condition: new, machine/vehicle number: 06017a31026c05fc8f6ccf5ae, empty load weight: 3,055 kg, maximum load weight: 14,945 kg, overall weight: 18,000 kg, axle configuration: 2 axles, tire size: 235/75 r17,5, Further information Chassis Changing turntable Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 Turntable with sturdy ball bearing slewing ring 2 wheel chocks with holder Cjdpfx Aji Ri Rcehyerk Aluminum side bumper Steel underride guard Quarter-shell mudguards at the front and half-shell mudguards at the rear Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the motor vehicle, EBS, electronic braking system with EBS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in both lowering and lifting position Wheels and tires 235/75 R17.5 tires of the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights in LED with resistor, amber LED lighting at the side, license plate lighting in LED, (Note! with certain towing vehicles, misdiagnosis may occur although the function is given) 2 white front position lights in LED 2 white/red rear lane departure lights in LED 1 x 15-pin plug at the front, with connecting cable, Additional LED work light(s) at the rear, switched via reversing light Approval / plates Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Attention: Archive pictures!

Condition: new, machine/vehicle number: 5b4d5b70c0e4954373dd5bf0b, empty load weight: 3 kg, maximum load weight: 14 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 435/50 r19,5, Further information Chassis change central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 / 7.45 and 7.82 1 pair of front gear support legs, with straight lower section and single-sided operation in FR right 2 wheel chocks with holder Aluminum side bumpers Steel underride guard Half-shell mudguard Spray flaps Towing device central axle trailer Tow bar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or exact testing still required in case of order) Under-coupler drawbar, free drawbar length approx. 2200 mm Towing height: 380 (Note! is not printed in the offer, compare with the technical data on the first page) Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake system Colored line routing for easy servicing. Air supply 208 liters Spring-loaded parking brake 2 swap-proof coupling heads at the front, with connecting lines to the engine trolley, connection in FR right-hand side EBS, electronic brake system with EBS plug at the front, with connecting cable, connection in FR right-hand side Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in both lowering / lifting position Wheels and tires 435/50 R19.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, connection in FR right-hand side 2 additional LED work lights at the rear, switched via reversing light 1 LED worklight at the front, centered between the carriers, radiating to the rear, switched via reversing light Country of registration / plates Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Crsdji Ri Iwjpfx Ahyek Attention: Archive pictures!

Condition: new, machine/vehicle number: dc46d2e1cd272305b99fb3160, empty load weight: 9,800 kg, maximum load weight: 31,200 kg, overall weight: 41,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Vehicle consisting of: Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with interchangeable 2 kingpin and 2 kingpin positions 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2 wheel chocks with holder Aluminum side collision protection Quarter-shell mudguards in front of and behind axle unit 1st pair of wheel recesses after gooseneck recessed in the low bed of the tramline area, slanted towards the entrance. Length at bottom approx. 1600 mm, depth of wheel recesses approx. 260 mm. Note! Frame in main beam area 260 mm higher than wheel recess. 2nd pair of wheel recesses between A and B axle. Bottom length approx. 350 mm, depth approx. 260 mm. Note! Frame in main carrier area 260 mm higher than wheel recess. If wheel loaders are to be driven and the overall height is to be checked, we request a technical data sheet for the wheel loader types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses are required by the customer). Wheel recess cover can be pulled out from the main frame, with wooden inserts. Widenings extendable to 3,000 mm (not in the rear slope and not in the wheel recesses below) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Csdpfx Aei Ri Hcshyjrk Storage compartment for wooden planks on gooseneck, front transverse Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 2 pairs of ring lashing eyes, 5 tons each at the front on the gooseneck 11 pairs of lashing rings at the top and sides, each 10 tons, embedded in the outer frame 2 x on gooseneck9 x in low loader bed distributed first lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 8 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, or instead of stake pockets 5 to. Ring lashing eyes embedded in the floor Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, without connecting cable with lifting & lowering valve Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle - driving stability system Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1 x LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm, removable with plug Floor Gooseneck with steel / checker plate covering Storage box embedded in drive-over slope to gooseneck Then with 70 mm softwood floor, in the wheel recesses underneath and in the wheel

Condition: new, machine/vehicle number: 628cde0fe99cc2d3c8eaa8dd8, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Crodpfx Ahji Ri Ddoyek Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: 113bec9dd54d24fa34a088424, empty load weight: 4,400 kg, maximum load weight: 27,600 kg, overall weight: 32,000 kg, axle configuration: 2 axles, tire size: 385/65 r22,5², Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Crodpfx Ahji Rizisysk Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10 J

Condition: new, machine/vehicle number: 42a74cba14ef2bfc0e90e52b2, empty load weight: 6,800 kg, maximum load weight: 28,200 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Welded fine-grained steel construction, lightweight design, fifth wheel plate with interchangeable 2 bolsters with hydr. mounting for Horsch Trailer Lift. Curved front end, hydraulic support legs, wheel chocks with holder, side collision protection special design, underride guard, foldable, quarter-shell mudguards in front of and behind axle unit, with anti-spray flaps only on last axle, stainless steel storage box W=800 /H=350 / D=350, tarpaulin pole with holder, towing hook at rear Axles+suspension BPW disc brake axles with 430 mm disc diameter, axle/chassis laser-measured to reduce tire wear and fuel consumption, air suspension with safety cables, 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake system, spring-loaded parking brake, 2 swap-proof coupling heads at the front, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Cedoi Rix Dopfx Ahyerk Vehicle stability system Wheels and tires 385/65 R22.5, steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable sockets at the front, without connecting cable, 2 additional LED work lights at the rear, switched via reversing light, night lighting via radio remote control. Hydraulics Low-pressure cylinder max. 170 bar, with HDK screw socket, fixed part, NW 48 mm (without hose connection), hydraulic actuation via truck power take-off, hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nutThe hydraulics for the lowerable side wall FR-left and the trailer lift arms are switched off automatically from approx. 20 km/h. The trailer lift arms can be locked separately so that the vehicle can only be unhitched. Body Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external cylinder holder. Side walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk-repellent top rail profile. Side wall in FR-left at the top approx. 7700 mm long and can be lowered hydraulically by approx. 600 mm in height for loading. Note! Only 2 positions possible, either completely closed or completely lowered. Before lowering the side wall, the roller tarpaulin must be opened and the crossbars inserted into the parking positions in FR-right or completely removed. Shovel and broom holder on the outside of the front wall. Inside with access to front wall. Greenline - conical and aerodynamic trough shape Swinging rear wall with 2 grain slides. Rear wall can be raised hydraulically by approx. 950 mm for unloading. Rear wall with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access ladder Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left. Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible, depending on the load.

Condition: new, machine/vehicle number: 1e7fb50bfb3671204fb4d0b92, empty load weight: 4 kg, maximum load weight: 33 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/55 r22.5, Further information Chassis Saddle Container Fine-grained steel welded construction, saddle plate with interchangeable 2 kingpins and 2 kingpin positions Container mounts: 1 x 20 feet in the middle without steel/checker plate covering in the rear area 2 x 20 feet or 1 x 40 feet with gooseneck tunnel without height adjustment at the rear and without folding center supports, no transport of containers without tunnel possible. 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EG Impact protection at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/55 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, rear and brake lights in LED, amber LED lighting on the side (Note! with certain towing vehicles, misdiagnosis may occur, although the function is given) 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 2 additional LED work lights at the rear, switched via reversing light Operating instructions Attention: Transport of filled tank containers is excluded! Csdpfxoi Riv Ne Ahyjrk Country of registration / plates Germany with Dekra approval and certificate (according to §13 EG - FGV) Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Attention: Archive pictures!

Condition: new, machine/vehicle number: 1acf251a278ec5cde4067a7b1, empty load weight: 5,800 kg, maximum load weight: 22,200 kg, overall weight: 28,000 kg, axle configuration: 2 axles, tire size: 235/75 r17,5, Further information Chassis saddle forwarding Fine-grained steel welded construction, saddle plate with replaceable 2 king pins Outer frame slightly slanted new design with Load-Lock profile for tensioning strap attachment 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Free support foot corner dimension or free swing radius to the rear approx. 1920 mm 2 wheel chocks with holder Aluminum side impact guard Steel underride guard Quarter-shell mudguards in front of and behind each axle 1 spare wheel holder for 1 e-wheel, with wheel fastening set 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Axles + suspension Drum brake axles of the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-applied parking brake Duomatic connection at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 235/75 R17.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin socket at the front, without connecting cable Crodpfx Ahjkv Uvzjyek Floor Screen printing plates approx. 30 mm thick, for high point load capacity for forklift axle load up to max. 5,600 kg Front wall / front corner stanchions 25 mm aluminum hollow profile, approx. 1 350 mm high, steel corner stanchions in volume design Approval country / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Front wall aluminum Attention! These are archive pictures!

Condition: used, machine/vehicle number: 0e87837859aec926e9db10456, empty load weight: 6,200 kg, maximum load weight: 11,800 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 05/2018, tire size: 235/75 r17,5, Year of construction: 2017, Further information Chassis: Welded steel construction, double offset with drop deck in front of and behind axle unit, drop deck slanted towards entrance, turntable with strong ball bearing slewing ring, folding rear support, wheel chocks, side collision protection, quarter-shell mudguards Lashing eyes: above front axle: 2 pairs of ring lashing eyes per 5 tons at the front on the offset drop deck/rear axle: 6 pairs of lashing eyes laterally in the drop deck per 8 tons, 6 pairs of lashing eyes per 5 tons between the side members, pair of stake pockets embedded in the outer frame, inside 70 x 40 mm, or instead of stake pockets, 5 tons ring lashing eyes embedded in the floor. Ring lashing eyes embedded in the floor Drawbar: tested 40 mm drawbar eye Crsdpei Ri N Uefx Ahyek Axles: BPW drum brake axles Brake system: 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable front coupling heads Electrical system: 24 volt, multi-chamber lights, amber lighting at the sides, 2 white position lights at the front 2 white/red lane departure lights at the rear, rotating beacon with holder, pair of warning signs illuminated and extendable to 3,000 mm, 2 x 7-pin interchangeable plugs at the front Floor: Front offset with steel / checker plate covering, storage box recessed in drive-over slope to offset, tramline area and in the middle between the beams with steel / checker plate covering, rear slope with 70 mm softwood floor, deep loading area incl. rear slope 5900 mm Drive-on ramps: Hook-in strip for aluminum ramps across the entire width. as U-profile across the entire width Pair of aluminum ramps 800 mm long, approx. 400 mm wide, load capacity per pair 14,000 kg, Storage compartment for ramps between the beams Approval: contour marking with reflective strips to ECE R 048, white at the sides and red at the rear

Condition: new, machine/vehicle number: 1eb6bdba4d54d87ab018b84c2, empty load weight: 3 kg, maximum load weight: 14 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 445/45 r19,5, Further information Chassis Wechel central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 1 pair of gear support legs at the front, with straight lower section and single-sided operation in FR right 2 wheel chocks with holder Aluminum side bumpers Steel underride guard Half-shell mudguard Spray flaps Towing device central axle trailer Towbar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or exact testing still required in the event of an order) Without length adjustment of drawbar Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Air supply 208 liters Cedpfji Ri Itsx Ahyork Spring-applied parking brake Duomatic connection at the front, with connection line to the motor vehicle, connection in FR-left EBS, electronic braking system with EBS plug at the front, with connecting cable, connection in FR right-hand side Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in both lowering / lifting position Wheels and tires 445/45 R19.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, connection in FR right-hand side LED work lights on both sides (switched via reversing light) LED worklights at the front, centered between the carriers, radiating to the rear, switched via reversing light Operating instructions Special approval required if the overall length of the train exceeds 18,750 mm. Observe country-specific approval regulations. Country of approval / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Attention: Archive pictures!

Condition: new, machine/vehicle number: 408ba9a39bbb8087056d6e563, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3,000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° / D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel housing area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Credpfx Aoi Ri Daohyjk Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of approval / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized

Condition: new, machine/vehicle number: 2f960ff7c44de83fd060ec5df, empty load weight: 6,750 kg, maximum load weight: 28,250 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only Tarpaulin pole with bracket Tow hook at the rear Axles+suspension Crsdoi Rizfspfx Ahyjk SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection) Hydraulic actuation via truck power take-off Troughs Round steel body in light Master Agrar design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Aluminum rear wall on pendulum bearings with double-joint hinge and with 2-leaf door division 1/2 to 1/2, top with swinging gallows, with one grain slider per door. With external espagnolette lock and mechanical locking at the bottom, Side walls 3 mm thick throughout, base 3 mm thick throughout, wear and weight-optimized design, Standing platform with ladder, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10 J

Condition: new, machine/vehicle number: 11be0b1246b37a0869e99ab60, empty load weight: 5,100 kg, maximum load weight: 29,900 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5², Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface Crjdsi Rixyopfx Ahyjk With anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Support bracket

Condition: new, machine/vehicle number: 7272fc3b6a97f9be58a222f05, empty load weight: 5 kg, maximum load weight: 32 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis Saddle Container Crsdei Riv Ejpfx Ahysk Fine-grained steel welded construction, fifth wheel plate with interchangeable 2 kingpins and 2 kingpin positions Front locking on tipping ram support frame with incl. guide wedges on both sides Incl. guide wedges, rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Container mounts: Locking cross member, 2-fold for locking 1 x 30 foot or 1 x 40 foot container. Adjustment via central telescope as an interlocking central tubular frame with bolt lock. Optimum fifth wheel load when transporting 30 foot and 40 foot containers. 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EG Hydraulics 100 Low-pressure cylinder max. 150 bar, with HDK screw socket, fixed part, NW 48 mm. (without hose connection) Hydraulic actuation via truck power take-off Incl. Hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nut Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension Brake system 170 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake Tele Control Axle relief for easy telescoping 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck instal. calibrated scales) Wheels and tires 385/65 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 2 additional LED work lights at the rear, switched via reversing light

Condition: new, machine/vehicle number: d24246f092ae53c0e155d19dd, empty load weight: 2,400 kg, maximum load weight: 13,600 kg, overall weight: 16,000 kg, Further information Chassis tandem trailer Welded steel construction with approx. 152 mm high floor assembly, load-oriented and torsion-resistant steel frame construction. Longitudinal beam floor construction with a load-resistant outer frame and with guide tunnel at 600 mm intervals, tunnel with guide at the top and sides, tunnel height approx. 45 mm, 4 x swap body corner fittings on 20ft base. Crsdpfx Ahekt Ni Usyek 4 x support legs for Jumbo parking height 970 mm, extendable and foldable sideways by 90° with short safety strut and safety catch, bolt safety catch on the frame, stable drop latch as second transport safety catch, -symmetrical arrangement of support legs form A 2 for CWB C 745 / 782 for parking height of approx. 970 mm Reinforcement between the support legs 7 pairs of lashing eyes embedded in the outer frame, 2.5 tons each Heavy-duty pallet stop on both sides, approx. 20 - 25 mm high, with lashing option every 200 mm, loading height reduced by approx. 20 - 25 mm Door stop on the side Impact protection at the rear made of flat iron Floor Screen printing plates approx. 27 or 30 mm thick, manufacturer's choice, for high point load capacity, for forklift axle load up to max. 4400 kg Front wall/front stanchions 2,800 mm high, rest with tarpaulin, steel corner stanchions in volume design, release device for side tarpaulin on front wall Center stanchions 1 pair of sliding stanchions can be moved along the entire length, with 4 insertion pockets and a long pocket at the bottom. Insertion slats 3 rows of aluminum V-insertion slats or wooden insertion slats of the manufacturer's choice, 1 additional row/rows of aluminum V-slats Rear wall/rear stanchions Rear corner stanchions, steel up to lower edge of roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet Rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps Stainless steel tension locks Roof Sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-shaped roof rail for automotive industry, internal width between the roof rails approx. 2,490 mm, tarpaulin color: white EcoLift - lifting roof can be raised by approx. 380 mm, with gas pressure damper support, Approval / plates Country of approval: Germany Manufacturer's certificate in accordance with EN 12642 XL Paint finish Hot-dip galvanized frame Front corner stanchions hot-dip galvanized Front wall aluminum Rear corner stanchions Hot-dip galvanized Rear wall white Tarpaulin RAL 9005 jet black with advertising lettering Attention! These are archive pictures.

Condition: used, machine/vehicle number: 2faf8161dfc64d2a606ca8319, empty load weight: 2,600 kg, maximum load weight: 10,800 kg, overall weight: 13,400 kg, axle configuration: 2 axles, first registration: 11/2013, tire size: 285/70 r19,5, Year of construction: 2013, Further information 4 VEHICLES AVAILABLE! - 4 VEHICLES AVAILABLE! - 4 VEHICLES AVAILABLE! - 4 VEHICLES AVAILABLE! Fine-grained steel welded construction, fifth wheel coupling, make of our choice for 2\ kingpin with ball bearing slewing ring, max. 20° stop, telescopic support foot, 2 wheel chocks with holder, steel underride guard, half-shell mudguards \CLG\ under-coupler drawbar with tested 50 mm drawbar eyes to the dolly and to the motor vehicle. BPW disc brake axles, air suspension with lifting & lowering valve 2-line compressed air brake system, spring-loaded parking brake, 2 non-interchangeable coupling heads at the front, with connecting lines to the tractor unit2 non-interchangeable coupling heads to the trailer EBS, electronic brake system with EBS plug at the front, with connecting cableEBS connecting cable to the trailer Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load recognition for trucks via EBS, without truck instal. 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 1 x 15-pin plug at the front, with connecting cable to the truck 1 x 15-pin plug with connecting cable to the trailer Country of registration: Germany, with Dekra approval, prepared for single-line license plate holder, contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Fine-grained steel welded construction, fifth wheel coupling, make of our choice for 2 kingpins with ball bearing slewing ring, max. 20° stop, telescopic support foot, 2 wheel chocks with holder, steel underride guard, half-shell mudguards CLG under-coupler drawbar with tested 50 mm drawbar eyes to the dolly and to the motor vehicle. BPW disc brake axles, air suspension with lift & lower valve 2-line compressed air brake system, spring-loaded parking brake, 2 non-interchangeable coupling heads at the front, with connecting lines to the tractor unit2 non-interchangeable coupling heads to the trailer EBS, electronic brake system with EBS plug at the front, with connecting cableEBS connecting cable to the trailer Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load recognition for trucks via EBS, without truck instal. 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 1 x 15-pin plug at the front, with connecting cable to the truck 1 x 15-pin plug with connecting cable to the trailer Country of registration: Germany, with Dekra approval, prepared for single-line license plate holder, contour markings with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Saddle height approx.: 1150 mm Crjdpfxji Ri N Rj Ahyek

Condition: new, machine/vehicle number: 06b624786df9f4b5c196a36b0, empty load weight: 3 kg, maximum load weight: 11 kg, overall weight: 14 kg, axle configuration: 2 axles, tire size: 285 / 70 r 19,5, Further information Chassis central axle tipping trailer Welded steel construction, continuous tipping shaft at the rear with 80 mm ball tipping bearing 2-speed gearbox support foot at the front Folding rear support Wheel chocks with holder Steel underride guard Rear spray flaps across the entire width Quarter-shell mudguards Lockable storage space for access ramps underneath the loading area Towing device central axle trailer Drawbar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 285 / 70 R 19,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear Lights completely in LED version (note! with certain towing vehicles, misdiagnosis can occur, although the function is given) 1 x 15-pin plug at the front, with connecting cable, Hydraulics Three-way tipping mechanism, hydraulic multi-piston press with lift limiter and safety cable, Low-pressure cylinder up to max. 170 bar, without throttle. If necessary, this must be retrofitted to the truck. Hydraulic operation via truck power take-off Hydraulic connection with SVK plug NW 10/3, incl. connection hose Tilting bridges Sturdy tipper body with 4 mm sheet steel floor, steel side wall structure, continuous side walls, hinged and pivoting with central locking at the bottom. Rear corner stanchions pluggable. Rear wall can be folded down and pivoted, with central locking at the bottom. Platform length approx. 5,000 mm, side walls with 6 hinges at the bottom. Dropside retraction springs (not possible with split side walls) Rear wall hinged and as 2-leaf door (cannot be folded down), with door holder and protective rubber on the side Platform width 2420 mm 5 pairs of lashing eyes in the floor, 5 tons each Country of registration / plates Country of registration: Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Codpfxji Ri Ipe Ahyjrk Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paintwork Hot-dip galvanized frame incl. passivation15-year warranty against rusting through Dropside/bridge RAL 3002, carmine red Please note! Bridge only primed inside! Attention: Archive pictures!

Condition: new, machine/vehicle number: 2428b2018baf171e60fef6740, empty load weight: 8,900 kg, maximum load weight: 32,100 kg, overall weight: 41,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with interchangeable 2 kingpin and 2 kingpin positions, 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Mudguards in front of 1st axle and rear of each axle with anti-spray, according to EC Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 2 pairs of ring lashing eyes, 5 tons each at the front on gooseneck 11 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 2 x on gooseneck 9 x distributed in the low loading area First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 8 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Crodei Ri E Ropfx Ahyjk Air suspension Wheels and tires 235 / 75 R 17.5 brand of the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, without connecting cable with lifting & lowering valve Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle - driving stability system Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1 LED rotating beacon with holder, switched via parking light (light can be removed) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Gooseneck with sheet steel covering Storage box recessed in drive-over slope to gooseneck Then with 70 mm softwood floor, steel/ checker plate covering in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 9 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK socket NW 10/3, without connecting hoses Operating instructions With 10,000 kg axle load, a special permit is required, only indivisible load possible!!! Special permit required if total train weight exceeds 40 tons! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) When applying for a special pe