Semi low-loader

HRD STLM 3N | 3-AXLE | SLIDING RAMPS | STEER & LIFT...

Condition: new, maximum load weight: 31,500 kg, overall weight: 42,000 kg, axle configuration: 3 axles, Year of construction: 2026, Equipment: ABS, Wiese 3-axle semi-trailer with lift table and fold-down rear. Ideal for transporting forklift trucks and/or work platforms. Technical data. 3 x 10 to. axles Lift axle Steering axle Smart Steering (steers forwards and backwards) Outer beam chassis with slope 18-tonne neck design suitable for 2- and 3-axle semitrailer tractors Lifting table hydraulically movable in 3 positions Rear in folding rear design incl. hydraulic extensions, can be used as drive-on ramps, drive-over ramps or as a loading area (overall length reduction when rear is raised) Remote control for ramps and lift table Front wall Grid floor Numerous lashing points SmartBoard Central lubrication system Spray-galvanized and painted steel construction Numerous optional extras are available: e.g: Cable winch Storage box on the saddle step aluminum rims Kdjdsvw Hmtjpfx Antot Further information on request.

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, 3-Axle MULTIMAX "PLUS" semi-trailer, air-suspended and with hydraulically forced steering axles. Technical data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h (legal) Total weight: 49500 kg / 31500 kg Fifth wheel load: 18000 kg Axle load: 31500 kg / 31500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Kingpin offset to rear approx.: 2,100 mm Fifth wheel height loaded approx.: 1205 mm Platform length approx.: 9,600 mm Extendable by approx.: ? Platform width approx.: 2,540 mm Loading height at max. load approx.: 890 mm Suspension travel approx.: -55 / +145 mm Axle spacing: 1,360 mm Total weight dependent on fifth wheel load: Yes Special permit required if exceeding country-specific regulations. Technical description Gooseneck: Gooseneck in SNT design to optimize platform length, length approx. 3,900 mm, rear with a bevel of approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor-trailer combinations: 4 x 2 and 6 x 2. Platform: Platform, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6°. Platform behind the gooseneck can be hydraulically raised and lowered, length approx. 3,000 mm, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS A pair of two-piece AXS steel ramps with a length of approx. 4,920 mm and a width of approx. 900 mm. Open grating deck. Hydraulically folding ramp ends. Ramps can be individually hydraulically shifted outwards by approx. 235 mm and inwards by approx. 365 mm. Maximum load and angle of inclination according to technical data sheet: C470319 Maximum inclination angle with lowered platform: 9° Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced steered. Technical axle load: 12,000 kg Air suspension with lifting and lowering valve. Axle tool. Tires: 235/75 R 17.5 3PMSF, twin tires. Manufacturer according to our choice Load index 143/141J (144/144F) Braking system: Braking system of the brand WABCO EBS-E according to EU regulations. Without connection cable to the tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" design according to EU regulations. (ASS 3) Metallization: Complete HRM metallization (High Resistance Metallization) Complete steel structure shot-blasted, then hot-dip galvanized with ZINACOR 850 (Zinc 85% - Aluminum 15%). Painting: 6-coat finish: Complete steel structure shot-blasted after welding. 1 coat of zinc-based primer, 1 coat of adhesion primer. Top coat with 2 coats of 2-component paint (acrylic), solid color in RAL colors of your choice, followed by sealing of the cavities with special wax. Rims in silver. Multi-color and special paint finishes available at an extra cost. Steel structure: Steel structure made of high-strength fine-grain steels. Kodpfx Asizu Ntontjdt Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders tested according to DIN-EN 287-1. Welding process MAG according to EN ISO 4063. Protective gas M21 according to EN ISO 14175 Front wall made of steel, plug-in, approx. 400 mm high Connection strip for supply lines to the tractor unit, mounted at the height of the outer frame profile. ASPÖCK-UNIBOX on the connection strip at the front with sockets 24N, 24S & 15-pole. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pole connection according to ISO-12098 If your pin assignment differs from the ISO connection standard, please inform us. "Anderson" socket on the connection strip at

Condition: used, maximum load weight: 42,500 kg, overall weight: 60,000 kg, axle configuration: 3 axles, first registration: 06/2022, with 12 axles, hydraulically suspended and divided, with hydromechanical forced steering, rear taper and drive-on ramps STZ-L Gooseneck - Robust welded steel construction - Engineered loading platform 3,950 x 2,480 mm including rear taper - Hydromechanical forced steering (dual-circuit steering system) - Turntable-mounted fifth-wheel plate with interchangeable 2-inch or 3.5-inch kingpin and adjustable steering wedge - Fifth wheel load: 24 t - Rear max. steering radius: 2,600 mm Loading platform - Lowered outer sections 4,630 mm long, 420 mm deep, resulting in a loading height of 470 mm or 830 mm with floor inserts - Extendable by 2,053 mm - Includes aluminum bridging rails for creating level surfaces - Excavator boom trough at rear running gear: 4,900 mm long, 880 mm wide, 480 mm deep - Length of rear running gear: 4,900 mm incl. 500 mm rear taper, loading height 890 mm - One pair of wheel recesses in lower deck - 3-axle hydraulically suspended running gear - Split Gigant axles with 600 mm stroke Rear of vehicle - Tapered design, 500 mm - Rear hydraulic support Drive-on ramps - Two-part drive-on ramps, 2,850 + 1,850 mm long, 800 mm wide - Rubber-coated with climbing bars Braking system - Dual-line full air braking system with diaphragm brake cylinders - Automatic load-dependent brake (ALB) - Automatic slack adjusters (AGS) - Parking brake via spring-loaded cylinders - ABS brake Special equipment Kdedpfew Etd Tox Antjt Radio remote control for steering and ramp operation Central lubrication system Technical data Gooseneck Loading platform (LxW): 3,950 x 2,480 mm Loaded fifth wheel height: 1,300 mm Loading platform Platform (LxW): 10,030 x 2,850 mm, extendable by 2,053 mm Lowered outer sections: 4,630 mm + 2,053 mm extension Center beam: 980 mm Excavator trough: 4,900 mm long, 880 mm wide, 480 mm deep Steering 1st to 3rd axle: hydromechanically forced steered (dual-circuit system)

Condition: new, empty load weight: 10,900 kg, maximum load weight: 37,100 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 9,600 mm, loading space width: 2,540 mm, loading space height: 890 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, operation weight: 10,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, with a bevel at the rear of approx. 1,000 mm x 6° -Technical fifth wheel load: 18,000 kg -For tractor units: 4 x 2 and 6 x 2 Loading area: -Loading area, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6° -Loading area can be raised and lowered hydraulically after the gooseneck, length approx. 3,000 mm, load capacity up to approx. 9,000 kg -Grating and sheet metal floor approx. 5 mm as additional reinforcement on the bevel of the loading area Ramps: -A pair of two-part AXS steel ramps with a length of approx. 4,675 mm and a width of approx. 900 mm -Grating floor -Hydraulically hinged ramp tips -Ramps can be moved hydraulically by approx. 235 mm outwards and approx. 365 mm inwards -Painted sand coating on the outer frame of the ramp and on the ramp tip -Flashlights on the outside of the ramp tips with switch next to the ramp controls -Ramp secured in driving position using a quick release Axles, suspension and tires: -BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle with self-steering -1st Axle with traction aid -Operation via the brake pedal in the tractor unit -Technical axle load: 12,000 kg -Air suspension with lifting and lowering valve -235/75 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 -TPMS tire pressure monitoring sensors mounted in all wheels including spare wheels Braking system: -WABCO EBS-E brand braking system in accordance with EU regulations Paintwork: -Semi-trailer MB 7350 Nova gray Accessories included: -Bulkhead made of steel, plug-in, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -JOST module B - static test load = 50,000 kg -Continuous grating with 5 mm sheet metal underlay as additional reinforcement -Painted sand coating Kjdjuadk Nopfx Antjdt -Cutouts in the outer frame of the loading area and the lifting bed for hanging control valves for the hydraulic ramps on the right of the vehicle -2" kingpin -Central lubrication system with 1 pump, brand BEKAMAX -On the gooseneck 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized -Electric cable winch, approx. 5,400 kg pulling force, with radio remote control -Wire cable approx. 24 m long, cable ø approx. 9.5 mm, including cable pressure roller -WABCO Smart Board System -4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Condition: new, maximum load weight: 25,645 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete stock of immediately and soon-to-be available vehicles on our website. Excerpt from equipment specification. Complete specification available on request. Load area: - Low-bed design with central beam, extendable version, approx. 6,750 mm in length - 5 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the loading platform (LC 10,000 daN) Gooseneck: - Hydraulic lifting/lowering gooseneck, detachable Rear chassis: - Short rear chassis with closed outer frame and checker plate covering - Chassis with excavator trough, closed in the rear half for housing the air tanks - 2 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Air suspension with raise/lower control valve Tyres: - Tyres 245/70 R 17.5, 3PMSF - TPMS: Tyre Pressure Monitoring System according to ECE R 141 Brake system: - Wabco braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality single-tone 2-component (2K) top coat in RAL 3000 Flame Red Including the following additional equipment: - 2 kingpins - Galvanised steel front wall, approx. 400 mm high - Remote steering from front and rear, operated by cable remote control with push buttons, including single tracking control for the axles (no installation in the tractor unit) - Electro-hydraulic unit - Axle load gauge including load diagram Kdjdpfx Aexf Silsntjt - On the gooseneck, removable aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). Rear galvanised stake pockets are removable. (Body length approx. 2,560 mm) - Separate air connection with air gun on the gooseneck - 2 work lights with switch on the trailer, mounted on the left and right of the gooseneck platform - 1 INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck - 6 pairs of stake pockets for insertable posts approx. 100 x 50 mm in the outer frame of the load area, 2 pairs in the chassis outer frame - Galvanised, extendable width extensions approx. 230 mm per side - Hydraulic connections from gooseneck to low bed with multi-coupling (instead of screw couplings). No seal guarantee included. - Central lubrication system with 2 BEKAMAX (Pico) pumps, standard NLGI-2 grease, with removable protection around the pump - 2 pairs of WADER container locks on the loading area, for 1x20' container - 1 removable galvanised intermediate table with 1 pair of WADER container locks - 1 pair of steel ramps for bridging the low bed’s hook mountings - Anti-slip sand-coated layer painted on the load area - HRM Metallisation (High Resistance Metallisation)

Condition: new, overall weight: 36,000 kg, axle configuration: 2 axles, loading space length: 7,650 mm, loading space width: 2,330 mm, loading space height: 1,470 mm, loading space volume: 25 m³, Year of construction: 2026, Equipment: ABS, lfd 12053 STEEL TRUCK 25 m³ SCHWARZMÜLLER 2-axle HARDOX TRUCK / HEAVY DUTY /25 m³ 5 mm make/manufacturer: SCHWARZMÜLLER EZL: NEW VEHICLE dimensions: 7650 x 2330 x 1470 volume: 25 cbm. permissible total weight: 36000 kg empty weight: 5540 kg Kdjdpfxevuip Es Antst load capacity 18000 kg air suspension disc brakes ABS EBS fifth wheel height 1300 axle make: SAF HD 430mm lift axle tarpaulin tarpaulin color: silver body paintwork: 7001 silver gray chassis paintwork: 7021 black gray tires: 4 ply tire condition: NEW tires HA 385/65 R 22.5 HEAVY DUTY STEEL TRUCK with HARDOX STEEL floor 5 mm side wall 4 mm for gravel or excavated earth! rear flap !!!!! 15 + 2 x 7-pin socket at the front HD 250 bar cylinder with central grease nipple SAF disc 430 mm reinforced axle LIFT AXLE fully automatic / starting aid also via switch 15 pin = pin 12 / 7 pin = pin 6 automatic lowering when tipping (via switch on/off) platform / roll tarpaulin 1300 mm ash / Schwarzmüller telematics installed all information without guarantee, subject to prior sale!! if you have any questions about this or another trailer / car please call us. if you have any questions for this or an other trailer / car please call us.

Condition: new, maximum load weight: 36,937 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer low loader with hydr. gooseneck Available immediately! TECHNICAL DATA: * Semi-mounted height 1,250 mm * Outer length 13,190 mm * Gooseneck length 3,950 mm * Platform length 9,240 mm * Platform height 875 mm * Wheelbase 8,480 mm * Wheelbase 1,360 mm * Axle load 30,000 kg * BPW axles with air suspension and drum brakes, 10 tons load capacity * Unladen weight 11,063 kg * Overall width 2,550 mm * Permissible gross weight (60 km/h) 52,800 kg * Permissible gross vehicle weight (80 km/h) 48,000 kg CHASSIS: * 2x rigid axles at the front, 1x self-steering axle at the rear * Overload-dependent manual axle lift system on the 1st axle * 12-wheel tires 245/70R17.5 * Air suspension, 1x load pressure gauge CHASSIS: Made of high-quality and high-strength S700 MC steel * Gooseneck with 90° vertical corners * Jost supports at the front * Folding rear supports * Grid floor RAMP: * Drive-on ramp capacity 40 tons * 2x hydraulic ramps, suitable for hydraulic sliding/folding operations with galvanized steel surface, 4,200 mm length and 850 mm width, 9 degree ramp angle, load capacity 40,000 kg and 3,510 mm height in closed position * Hydraulic gooseneck ramp 2,800 mm long 10° angle LOAD SECURING: * Lashing rings 6x2 on the gooseneck with 6 tons capacity, 6x2 on the platform with 6 tons capacity, 8x2 on the outer frame with 6 tons capacity * 8x2 stanchion pockets MISCELLANEOUS: * 1x rotating beacon * 1x work light * 2x2 extra-wide boards with lighting * SmartBoard Ksdpjt Aqv Sefx Antedt For further information please do not hesitate to contact us

Condition: used, maximum load weight: 23,000 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 04/2025, loading space length: 9,200 mm, loading space width: 2,550 mm, total width: 2,550 mm, Year of construction: 2025, Equipment: ABS, GVN 3GVN29 OVERWIDTH PANEL/KOÇ/LIFT/HYDR. RAMP ----VEHICLE HISTORY * NEW VEHICLE * VIDEO AVAILABLE UPON REQUEST VEHICLE EQUIPMENT TECHNICAL DATA AND EQUIPMENT SHEET VEHICLE TYPE: * GVN TRAILER - 3-AXLE EUROPEAN MODEL TRADEMARK: * 3GVN29 ----WEIGHT SPECIFICATIONS WEIGHT IN OPERATING CONDITION * 13,000 KG DISTRIBUTION OF THIS WEIGHT ON THE AXLES AXLE 1: 3,653 KG AXLE 2: 3,653 KG AXLE 3: 3,653 KG ACTUAL VEHICLE WEIGHT * 13,000 KG Kdedpfx Aow Dlqientst TECHNICALLY PERMISSIBLE MAXIMUM GROSS VEHICLE WEIGHT * 58,000 KG TECHNICALLY PERMISSIBLE MAXIMUM AXLE LOADS AXLE 1: 12,000 KG AXLE 2: 12,000 KG AXLE 3: 12,000 KG TECHNICALLY PERMISSIBLE MAXIMUM WEIGHT ON AXLE GROUPS GROUP 1: 36,000 KG MAXIMUM GROSS VEHICLE WEIGHT FOR REGISTRATION * 35,500 KG MAXIMUM AXLE LOADS FOR REGISTRATION AXLE 1: 8,000 KG AXLE 2: 8,000 KG AXLE 3: 8,000 KG MAXIMUM WEIGHT ON AXLE GROUPS FOR REGISTRATION GROUP 1: 24,000 KG TECHNICALLY PERMISSIBLE MAXIMUM STATIC WEIGHT ON THE COUPLING POINT * 22,000 KG TECHNICAL MAIN DIMENSIONS (COC) * OVERALL LENGTH 13050 MM * LOADING AREA LENGTH 9200 MM * VEHICLE WIDTH 2550 MM * OVERALL HEIGHT 3000 MM * PLATFORM HEIGHT APPROX. 910 MM * NUMBER OF AXLES 3 * TIRE SIZE 235/75 R17.5 * SUSPENSION AIR SUSPENSION * COLOR RAL 5011----EQUIPMENT LIST - EXTENDED GOOSENECK * FIXED GOOSENECK * STEEL FRONT WALL * 2 STEEL SIDE DOORS, PLUG-IN * 1 STEEL REAR DOOR, PLUG-IN * STORAGE COMPARTMENT AT FRONT * STORAGE COMPARTMENT AT FRONT UNDER GOOSENECK * LOADING AREA ON THE GOOSENECK LOADING PLATFORM * HIGH-STRENGTH S355 STEEL * PLATFORM EDGES FACED WITH WOOD * SURFACE COVERED WITH STEEL SHEETING * 14 SIDE EXTENSIONS, EACH PLUS 230 MM * 14 FORGED STEEL LASHING RINGS, 16 TONS EACH * EXTENDING PANEL FOR OVERWIDTH * OVERWIDTH SILL * WARNING SIGN FOR OVERWIDTH * FASTENING POINTS * ADDITIONAL SUPPORTS * PRESSURE INDICATOR AXLES AND SUSPENSION * 3 AXLES * OSMAN KOC AXLES, TECHNICALLY EQUIVALENT TO BPW * STEERABLE AXLE, AXLE 3 * LIFT AXLE, AXLE 1 * TWIN TIRES ON ALL AXLES * SUSPENSION, FULL AIR SUSPENSION ON ALL AXLES * LIFT AXLE, AXLE 1, DRUM BRAKE BRAKE SYSTEM * EBS SYSTEM WABCO, ELECTRO-PNEUMATIC, EC NORM * AUTOMATIC REVERSING MECHANISM FOR THE STEERABLE AXLE * DRUM BRAKES ON ALL AXLES TIRES AND WHEELS * TIRES 235/75 R17.5 * SPARE TIRE YES * WHEELS 12 * MAXIMUM SPEED 80 KM/H * RIMS 6.75X17.5 STEEL, SILVER-GRAY * SPARE WHEEL AVAILABLE PAINTING * 2 LAYERS OF EPOXY PRIMER, 100 MICRONS EACH * MINIMUM 100 MICRONS 2K ACRYLIC PAINT * COLOR RAL 5011 ELECTRICAL AND LIGHTING * 24 VOLT SYSTEM, EC NORM * WATERPROOF, FROST-PROOF CONNECTIONS * SIDE AND POSITION LIGHTS * 6 REAR LIGHTS, 3-FUNCTION * 2 REVERSING AND WORK LIGHTS * 2 TURN SIGNALS * 2 LICENSE PLATE LIGHTS * 1 ROTATING BEACON * 2 TRIANGULAR REFLECTORS * REFLECTIVE STRIPS AND E-MARKING * TRAILER LIGHT SYSTEMS * ROTATABLE REAR LIGHTS RAMP * PERMANENTLY MOUNTED HYDRAULIC LOADING RAMPS * HYDRAULICALLY ADJUSTABLE SIDEWAYS, LEFT AND RIGHT * SUPPORT FEET, 24 TONS DYNAMIC, 50 TONS STATIC, OMS * MANUAL RAMP SUPPORTS * POWER CONNECTION FOR HYD

Condition: used, functionality: fully functional, empty load weight: 9,000 kg, maximum load weight: 29,000 kg, overall weight: 38,000 kg, first registration: 08/2020, color: red, Year of construction: 2020, ES-GE 2-axle low-bed, non-telescopic, Tridec steering Total weight: 38,000 kg Aggregate load (2 x 10,000 kg): 20,000 kg Fifth wheel load: 18,000 kg Unladen weight +/- manufacturer's tolerance: approx. 9,000 kg Payload: approx. 29,000 kg Overall length: approx. 13,650 mm Overall width: approx. 2,540 mm Length of loading area: approx. 13,200 mm Width of loading area: approx. 2,540 mm Front overhang: approx. 1,200 mm Front radius: approx. 1,750 mm Swing-through radius SZM: approx. 2,100 mm Saddle height: approx. 1,150 mm B dimension: approx. 12,000 mm Length of high bed: approx. 3,700 mm Loading height high bed: approx. 1,480 mm Length of low bed: approx. 6,500 mm Loading height low bed: approx. 250 mm Ground clearance low bed: approx. 100 mm Loading height above axle unit: approx. 3,000 mm Specification SZM A dimension: approx. 4,500 mm Semi-mounted height: approx. 1,150 mm Swing-through radius: approx. 2,100 mm Chassis: - Chassis made from high-quality fine-grained steels - Drop deck in rigid design - Axle unit cannot be lowered - Without excavator trough King pin -2" kingpin Supports - without front jacks Axles - 2 x 10,000 kg axles (17.5"), techn. 12,000 kg each - Gigant make - Closed drum brake. Asbestos-free brake linings - Automatic slack adjusters. Center centering - Center distance approx. 1,360 mm Suspension - Air suspension with lifting and lowering - 2nd ride height for air suspension (+ approx. 30 mm) Steering - Hydraulic stub axle steering - All axles are steered. Make "Tridec" Tires - 9 tires 245/70 R 17.5 with load index 146/146 F - Continental tires - Steel rims Brake - Dual-circuit air brakes in accordance with EC directive, make "Knorr" - Automatic load-dependent brake force control - Controlled via standard red/yellow air clutches in accordance with ISO 1726 - Electronic brake, "EBS", 7-pin socket in accordance with ISO 7638, mounted at the front, in accordance with EU directives. WITH ABS 4S/2M - With RSS (Roll Stability Support) - Parking brake by means of spring-loaded cylinder - 4 wheel chocks with holder - Without connecting hoses (reversible flex) to the tractor unit - Aluminum air reservoir - TIMG2 (Trailer Information Module) fitted to read out the current axle loads Underride guard - Integrated in the rear end plate Kdodpfx Asu U Np Tjntjt Side frame - Side frame made of UNP steel approx. 200 mm Load securing - 13 lashing points per side with 13,400 kg tensile force, can be folded outwards, mounted in the outer frame - 1 pair of lashing rings with approx. 13,400 kg lashing force in the rear area of the gooseneck, approx. 400 mm from the floor - 1 pair of lashing rings with a tensile force of approx. 13,400 kg at the rear in the low bed on the vertical neck - 7 stake pockets per side on the inside of the outer frame, for stakes approx. 80x50x4 mm, evenly distributed in the outer frame over the entire length of the cargo bed - 6 stake pockets welded to the outside of the side member on each side Floor - Approx. 28 mm thick hardwood floor with omega profiles, laid between the side members - Tear plate (approx. 8/10 mm) over the axle unit Front wall - Designed as a storage box with lid, approx. D 400 x H 450 mm, across the entire width of the loading area, beveled corners Drop sides - 3 plug-in anodized drop sides on the gooseneck, approx. 2,440 x 400 mm - Rear stanchions, galvanized Galvanization - Steel blasting of all iron parts - Galvanizing of the chassis Painting - Priming and single-color painting in RAL 3002 chi

Condition: new, maximum load weight: 38,290 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 8,500 mm, loading space width: 2,520 mm, Year of construction: 2026, * TS 3 Profile 30.0: ----Brake System: * Wabco EBS-E (electronic braking system) * Emergency release for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Last axle is self-steering with electro-pneumatic steering lock ----Suspension: * Air suspension with lifting and lowering function and RtR valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard operating box mounted on the trailer as an info tool, with pressure sensors for total axle load display * 15-pin electrical connector * LED lighting system 12/24V * LED rotating beacon (removable), mounted rear left ----General Attachments: * Side underrun protection * Support legs in front and mechanical swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder mounted underneath the chassis, right side ----Low Loader Platform: * Fifth-wheel platform with 45° chamfered front corners and a front toolbox made of galvanized sheet steel, W = 2,480 x H = 500 x L = 665 mm, with hinged lid * 400 mm high drop-side aluminum boards (RAL 9010 pure white), foldable and removable, along the platform sides * Rear wall insert – 150 mm high * Rear slope on the platform to the low bed, approx. 700 mm long * Fifth-wheel platform with 50 mm timber floorboards, and low bed platform with 60 mm timber floorboards * Checker plate over the axles ----Widenings: * 8 x mechanical fold-out width extensions to achieve a total width of 3 m (excluding the rear slope); extension boards included with storage on the platform * Mechanically adjustable warning panel sets at front and rear ----Load Securing (Lashing Package): * On the platform, 2 x 6.3 t lashing rings each side, plus 3 x 5 t lashing bars in the outer frame on each side * On the low-bed platform, each side: 2 x 13.4 t lashing rings; plus 4 x 10 t folding and retractable lashing rings recessed in the outer frame * Each side: 2 x 6.4 t lashing eyes, plus one lashing ring at the rear in the excavator arm recess * 2 x container locks immediately after the gooseneck in the low-bed platform ----Excavator Arm Recess: * Continuous excavator arm recess from end of last fixed axle over the steering axle up to the rear cross member, with internal reinforcement, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Ramps: * Single-piece, hot-dip galvanized mechanical-hydraulic loading ramps approx. 3,000 x 720 mm (mechanically adjustable laterally) * 4-way control block for later customer-side retrofitting of hydraulic ramp shifting * The outer plank of the ramp made from 50 mm hardwood * Climbing strips on the outer frame of the ramp and on the approach slope ----Hydraulics: * Hydraulic flow divider in trailer (for hydraulic pump capacity in truck over 40 up to 120 l/min) ----Loading Dimensions: Kedpfx Aol Tnvgsntodt * Fifth-wheel platform load area: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Unladen load height approx. 910 mm (incl. 860 mm approach slope) ----Fifth-Wheel Height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractor units) ----Paintwork: * Chassis, ramps, rear folding supports, widening consoles hot-dip galvanized * Axles, support legs, air tanks painted in black * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer warranty * Subject to error and prior sale * Sample images may show equipment not included with the offered vehicle ----Delivery Time: * Available from calendar week 38/2026