Low loader semi-trailer

ES-GE 2-Achs-Tiefbett (Tridec Lenkung)

Condition: new, empty load weight: 11,000 kg, maximum load weight: 27,000 kg, overall weight: 38,000 kg, axle configuration: 2 axles, loading space length: 7,300 mm, loading space width: 2,550 mm, tire size: 235/75 R17.5, color: grey, operation weight: 11,000 kg, Equipment: ABS, Chassis: - Steel frame welded construction with front and rear frame extensions and a low-bed without a rear slope - Frame neck + kingpin plate 225 mm - Low-bed designed for a point load of 25 tons over 5 m - Outer frame closed on the outside with welded lashing rings for securing cargo Lodpfxeiu Eu Ne Akkehn - Interchangeable 2" kingpin - Rear mounting rail for aluminum ramps Axles and Tires: - BPW low-loader axles, 10 tons axle load each, air spring diameter 360 mm - Air suspension with lifting and lowering device, stroke 220 mm (-60/+160 mm) - Wabco SmartBoard with ECAS function for 2 coupling heights + 100 mm - S-cam brake 300/200 mm, asbestos-free brake linings - Automatic slack adjusters - IVTM tire pressure monitoring system - 9 tires 235/75 R 17.5, tubeless Steering: - 1st and 2nd axles hydraulically steered via the fifth wheel coupling Floor: - Multi-layer glued panel floor with a thickness of 27 mm, flush with the outer frame and longitudinal beams - Reinforced underneath with GRP coating - 12 pairs of lashing rings welded into the outer frame (8 pairs RUD 8 tons – 6 pairs in the low-bed and one pair each on the gooseneck and at the front of the rear section – 2 pairs of lashing rings 4 tons on the gooseneck and rear section) - 6 pairs of mushroom-shaped load securing points in the outer frame in the low-bed - Storage compartment with lid in the floor of the low-bed, front left and right Front Wall: - 25 mm aluminum hollow profiles extending up to the lower edge of the roof with integrated tarpaulin tensioning device Sliding Tarpaulins: - Sliding tarpaulins on both sides with welded vertical and horizontal straps (spacing approx. 600 mm) and stainless steel tensioning closures - Adjustable tarpaulin straps (over center) up to a loading width of 4,000 mm, including tarpaulin extension with snap buttons and Velcro - Tarpaulin extension in the direction of travel: 300 mm, in height: 750 mm - Incl. eyelets for a loose tarpaulin extension part - 1 pair of vertical tarpaulin pockets with a length of approx. 1,000 mm, position in the low-bed at the front extension - With strap pockets Rear Wall: - Steel rear portal frame with lateral tarpaulin mounting device - Aluminum double-wing door, 25 mm thick - Both door wings can be fully folded in with door latch - One aluminum double-hinge hinge and two recessed handle recesses per door wing Front Corner Posts: - At roof height, screwed on at the front end Intermediate Posts: - 3 pairs of steplessly adjustable folding posts - The posts can be moved along the entire length using roller carriages - Intermediate posts can also be fixed in the rear platform in the low-bed Roof: - EDSCHA sliding tarpaulin (galvanized) with crossmember that can be moved in both directions (pushed forward together in the loading area) - Rear portal crossbar can be swung out - PVC tarpaulin roof without customs closure - Manually hydraulic lifting roof on both sides, stroke 450 mm - Lifting roof can be operated in the front (9x50) and rear (9x50) elevated positions - Including tarpaulin extension and tarpaulin rail at the rear - Tarpaulin can be extended by 900 mm at the front end wall Accessories: - Extendable warning signs (removable at the rear and front with socket) incl. position lights up to a loading width of 4,000 mm - Storage of the 4 warning signs on the front wall, inside, top right and left - 1 aluminum ladder with bracket 2,500 mm long on the front wall - 2 rows of aluminum slats self-locking - Sheet metal mudguard

Condition: new, maximum load weight: 31,500 kg, overall weight: 42,000 kg, axle configuration: 3 axles, Year of construction: 2026, Equipment: ABS, Wiese 3-axle semi-trailer with lift table and fold-down rear. Ideal for transporting forklift trucks and/or work platforms. Lodpfsvw Hmtsx Akkshn Technical data. 3 x 10 to. axles Lift axle Steering axle Smart Steering (steers forwards and backwards) Outer beam chassis with slope 18-tonne neck design suitable for 2- and 3-axle semitrailer tractors Lifting table hydraulically movable in 3 positions Rear in folding rear design incl. hydraulic extensions, can be used as drive-on ramps, drive-over ramps or as a loading area (overall length reduction when rear is raised) Remote control for ramps and lift table Front wall Grid floor Numerous lashing points SmartBoard Central lubrication system Spray-galvanized and painted steel construction Numerous optional extras are available: e.g: Cable winch Storage box on the saddle step aluminum rims Further information on request.

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, 3-Axle MULTIMAX "PLUS" semi-trailer, air-suspended and with hydraulically forced steering axles. Technical data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h (legal) Total weight: 49500 kg / 31500 kg Fifth wheel load: 18000 kg Axle load: 31500 kg / 31500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Kingpin offset to rear approx.: 2,100 mm Fifth wheel height loaded approx.: 1205 mm Platform length approx.: 9,600 mm Extendable by approx.: ? Platform width approx.: 2,540 mm Loading height at max. load approx.: 890 mm Suspension travel approx.: -55 / +145 mm Axle spacing: 1,360 mm Total weight dependent on fifth wheel load: Yes Special permit required if exceeding country-specific regulations. Technical description Gooseneck: Gooseneck in SNT design to optimize platform length, length approx. 3,900 mm, rear with a bevel of approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor-trailer combinations: 4 x 2 and 6 x 2. Platform: Platform, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6°. Platform behind the gooseneck can be hydraulically raised and lowered, length approx. 3,000 mm, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS A pair of two-piece AXS steel ramps with a length of approx. 4,920 mm and a width of approx. 900 mm. Open grating deck. Hydraulically folding ramp ends. Ramps can be individually hydraulically shifted outwards by approx. 235 mm and inwards by approx. 365 mm. Maximum load and angle of inclination according to technical data sheet: C470319 Maximum inclination angle with lowered platform: 9° Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced steered. Lhsdpfx Aoizu Ntekksn Technical axle load: 12,000 kg Air suspension with lifting and lowering valve. Axle tool. Tires: 235/75 R 17.5 3PMSF, twin tires. Manufacturer according to our choice Load index 143/141J (144/144F) Braking system: Braking system of the brand WABCO EBS-E according to EU regulations. Without connection cable to the tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" design according to EU regulations. (ASS 3) Metallization: Complete HRM metallization (High Resistance Metallization) Complete steel structure shot-blasted, then hot-dip galvanized with ZINACOR 850 (Zinc 85% - Aluminum 15%). Painting: 6-coat finish: Complete steel structure shot-blasted after welding. 1 coat of zinc-based primer, 1 coat of adhesion primer. Top coat with 2 coats of 2-component paint (acrylic), solid color in RAL colors of your choice, followed by sealing of the cavities with special wax. Rims in silver. Multi-color and special paint finishes available at an extra cost. Steel structure: Steel structure made of high-strength fine-grain steels. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders tested according to DIN-EN 287-1. Welding process MAG according to EN ISO 4063. Protective gas M21 according to EN ISO 14175 Front wall made of steel, plug-in, approx. 400 mm high Connection strip for supply lines to the tractor unit, mounted at the height of the outer frame profile. ASPÖCK-UNIBOX on the connection strip at the front with sockets 24N, 24S & 15-pole. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pole connection according to ISO-12098 If your pin assignment differs from the ISO connection standard, please inform us. "Anderson" socket on the connection strip at

Condition: new, empty load weight: 6,350 kg, maximum load weight: 38,650 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 13,600 mm, loading space width: 2,540 mm, suspension: air, tire size: 385/65 R22,5, Equipment: ABS, Loading platform: - 2 pairs of lashing rings that can be folded outwards (LC 5,000 daN) - 24 pairs of cutouts in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Fifth wheel: - JOST fifth wheel (mechanical) with a 2-speed gearbox for a 24-tonne lifting capacity (50-tonne test load) Axles and tires: - BPW axles, air-sprung, with disc brakes (430 mm), with raising/lowering function - Tires: 385/65 R 22.5 Braking system: - WABCO braking system in accordance with EU regulations, with EBS-E (2S2M) Paintwork: - First-class and durable corrosion protection of the standard bead-blasted welded frame is guaranteed by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) topcoat, single color in MB 7350 Novagrau - Rear part metallized and painted in RAL 9010 (Pure White) - Metallic paint not possible Steel structure: - Steel structure made of high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355 MPa) - S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system in accordance with EU regulations - Lighting: 24 volts - ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets - Connection according to ISO. - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Lodpfxjiu Etks Akkohn Included accessories: - Yellow-red air couplings on the galvanized front connection bar - 4 wheel chocks with bracket - 2" king pin - Galvanized steel front panel, approximately 1,600 mm high. EN12642-XL - White reflector tape in accordance with EU regulations on the sides of the trailer and red on the rear - European reflector signs (red-yellow) at the rear of the trailer - Loading platform with approximately 30 mm thick hardwood floor, edged with omega profiles - 10 pairs of socket pockets for 100 x 50 mm securing bars in the outer frame of the loading platform - 3 pairs of socket pocket strips, mounted transversely in the loading platform, for 100 x 50 mm securing bars - Storage for 1,000 mm securing bars, at the rear in the central beam - 1 spare wheel holder under the loading platform on the right side in the direction of travel - One mud flap at the rear of the trailer - Manual and description on a USB stick - One bracket for a rotating beacon at the rear of the trailer - One bracket for warning signs including socket on the gooseneck and on the rear panel, left and right - 6 pairs of WADER container pockets in the loading platform, for 1x 20ft container, 2x 20ft containers, or 1x 40ft container. Flush with the rear - Speed stickers 80 km/h on the rear and on both sides - Four warning signs, each extendable by approximately 400 mm, approximately 423 x 423 mm, with an LED position light - Load gauge for determining axle loads, including a load diagram - HRM metallization (High Resistance Metallization) of the outer frame - Complete steel structure bead-blasted, followed by the defined visible surfaces hot-coated with metallization using ZINACOR 850 (Zinc 85% - Aluminum 15%)

Condition: new, maximum load weight: 30,190 kg, overall weight: 43,000 kg, axle configuration: 2 axles, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the equipment list. Full equipment details available on request. Loading Platform: - Lowbed with external beams in extendable SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking mechanism - Supply lines protected inside the extendable side rails, automatically adjusting to the current bed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for attaching RUD screw-on rings Gooseneck: - Gooseneck in SNT design for optimized platform length, length approx. 3,750 mm - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractors: 4x2, 6x2 Rear Chassis: - Rear chassis in short version with closed external frame and checker plate cover - Running gear with excavator recess, closed in the rear half to accommodate the air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings horizontal, front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering Lhedsxarl Nspfx Akken - Technical axle load per axle: 12,000 kg - Air suspension with lift and lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF - Manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transmission to the truck via the standardized EBS interface in accordance with ISO 11992 - The truck must be capable of processing and displaying this data for correct operation Braking System: - Braking system according to EU regulations with EBS-E (2S2M) Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with indicators - ASPÖCK-UNIBOX at the front connection point with 24N, 24S, and 15-pin sockets as per standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel Construction: - Steel construction from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure is automatically shot-blasted after welding using a blasting turbine system - Second blasting process with corundum for optimal adhesion of coating system - HRM metallization of complete chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection - Final paint finish with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, as per RAL system 841GL - Rims in silver - Rear section metallized and painted RAL 9010 (Pure White) - Metallic paint not possible - Paint system tested in salt spray test as per ISO 9227-NSS - Cavities sealed with special wax Including the following additional equipment: - 2" King pin - One galvanized steel front wall, approx. 400 mm high - Remote steering of front and rear axles by cable remote control with pushbuttons, including single track axle monitoring (without installation in the tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Electro-hydraulic power pack - Preparation for mounting container locks for 1x 20' or 1x 40' container on the external beams - Without container locks

Condition: used, maximum load weight: 42,500 kg, overall weight: 60,000 kg, axle configuration: 3 axles, first registration: 06/2022, with 12 axles, hydraulically suspended and divided, with hydromechanical forced steering, rear taper and drive-on ramps STZ-L Gooseneck - Robust welded steel construction - Engineered loading platform 3,950 x 2,480 mm including rear taper - Hydromechanical forced steering (dual-circuit steering system) - Turntable-mounted fifth-wheel plate with interchangeable 2-inch or 3.5-inch kingpin and adjustable steering wedge - Fifth wheel load: 24 t - Rear max. steering radius: 2,600 mm Loading platform - Lowered outer sections 4,630 mm long, 420 mm deep, resulting in a loading height of 470 mm or 830 mm with floor inserts - Extendable by 2,053 mm - Includes aluminum bridging rails for creating level surfaces - Excavator boom trough at rear running gear: 4,900 mm long, 880 mm wide, 480 mm deep - Length of rear running gear: 4,900 mm incl. 500 mm rear taper, loading height 890 mm - One pair of wheel recesses in lower deck - 3-axle hydraulically suspended running gear - Split Gigant axles with 600 mm stroke Rear of vehicle - Tapered design, 500 mm - Rear hydraulic support Drive-on ramps - Two-part drive-on ramps, 2,850 + 1,850 mm long, 800 mm wide - Rubber-coated with climbing bars Braking system - Dual-line full air braking system with diaphragm brake cylinders - Automatic load-dependent brake (ALB) - Automatic slack adjusters (AGS) - Parking brake via spring-loaded cylinders - ABS brake Special equipment Lhodpfjw Etd Tsx Akkon Radio remote control for steering and ramp operation Central lubrication system Technical data Gooseneck Loading platform (LxW): 3,950 x 2,480 mm Loaded fifth wheel height: 1,300 mm Loading platform Platform (LxW): 10,030 x 2,850 mm, extendable by 2,053 mm Lowered outer sections: 4,630 mm + 2,053 mm extension Center beam: 980 mm Excavator trough: 4,900 mm long, 880 mm wide, 480 mm deep Steering 1st to 3rd axle: hydromechanically forced steered (dual-circuit system)

Condition: new, maximum load weight: 25,300 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment details. Full specifications available upon request. Neck (Gooseneck) * Gooseneck in SNT design to optimize loading platform length * Approx. 3,750 mm long, hydraulically liftable/lowerable and detachable * Technical fifth wheel load: 25,000 kg For tractors: 4x2 and 6x2 Kessel Bridge (Tiefbett section) * Low bed designed as extendable Kessel bridge in SUPER LOW design * Approx. 6,850 mm length * With mechanical locking * Service lines routed protected inside the extendable beams, automatically adjusting to match the low bed’s length Rear Chassis * Short version with closed outer frame and checker plate cover * Chassis with excavator trough, closed at the rear half to accommodate air tanks Axles * BPW axles and suspension, all axles hydro-mechanically forced steered * Technical axle load: 12,000 kg per axle * Air suspension with lifting and lowering valve Tires * GOODYEAR KMAX T 3PMSF (M+S) 245/70 R 17.5 twin tires. Load index 143/141J (146/146F) Brake system * Brand: WABCO, EBS-E according to EU regulations, without connection cable to the tractor unit Paintwork * 6-Coat final treatment * All-steel construction shot-blasted after welding * 1 layer of zinc-based primer * 1 layer of adhesion primer. Final coating with 2 coats of 2-component acrylic paint in a single color, followed by cavity sealing with special wax Trailer color * RAL 3002 Carmine Red * Rim color: Silver grey * Drop side color: Natural aluminum Accessories included * Removable steel front wall, approx. 400 mm high Lsdpfx Akev Sw E Ajkehn * 3 kW electro-hydraulic unit for hydraulic operations (except for hydraulic winches). Without supply connection installed on tractor unit * Spare wheel carrier in front of the gooseneck front wall * Side beams of the gooseneck with fixing holes for bolted lashing rings; first hole approx. 200 mm from the front, then at approx. every 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 lashing ring each left and right on the rear taper of the gooseneck (LC 6,000 daN) * 2" king pin * Hydraulic cross member for supporting the gooseneck on the tractor unit or a dolly * Air connection with air gun at the gooseneck * 1 pair of steel ramps with climbing strips and securing pins to bridge the mountings of the low bed * 1 lashing ring each left and right on the front cross member (LC 10,000 daN) * Outer side beams of the loading area prepared for removable loading floor * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the inside carrier’s exterior of the loading area * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the outer carrier’s exterior of the loading area (LC 10,000 daN) * Cut-outs above the lashing rings in the outer carrier’s upper flange * Mechanical pin-tab coupling from low bed to rear chassis, for swapping the loading floor or installing extension beams, with electro-pneumatic-hydraulic couplings * The outer carriers of the low bed coated with anti-slip sand finish for slip resistance * 2nd ride height for high ride position, max. ± 50 mm from normal ride position, without installation of controls from the tractor unit * 1 pair lashing rings with retaining spring at the transition from the low bed to the excavator trough (LC 10,000 daN) * Front and rear tapers

Condition: excellent (used), mileage: 308,000 km, power: 412 kW (560.16 HP), fuel type: diesel, tire size: 385/65R22,5, axle configuration: 8x4, wheelbase: 2,600 mm, fuel: diesel, brakes: retarder, color: red, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, suspension: other, permissible axle load (axle 1): 8,000 kg, permissible axle load (axle 2): 7,500 kg, permissible axle load (axle 3): 13,000 kg, Year of construction: 2015, Equipment: ABS, AdBlue, air conditioning, cruise control, electric window regulation, retarder, = Additional Options and Accessories = - Intarder - Refrigerator - Air Suspension - Air Horn - Parabolic Suspension - Radio/CD Player - Sleeper Cab - Sun Visor - Toolbox = Notes = Transmission model: MAN TipMatic 12 30 OD gearbox / Converter-Clutch with Retarder Color: Red Details: Manufacturer: MAN Type: TGX 41.560 8x4/4 BLS Chassis number: WMA87XZZ0FL071136 Year: 2015 Odometer: approx. 308,000 km Engine: 560 hp/412 kW / EURO 6 / SCR-2,700 Nm CR (D3876LF01) Transmission: MAN TipMatic 12 30 OD gearbox / Converter-Clutch with Retarder Front axle: 8,000 kg / Parabolic Suspension / Tires 385/65R22.5 Second axle: 7,500 kg / Air Suspension / Steering / Tires 385/65R22.5 Rear axles: 13,000 kg / Air Suspension / Hub Reduction / Double Tires / 315/80R22.5 Wheelbase: 2,600 mm + 1,440 mm + 1,420 mm GVW: 42,000 kg GCW: 180,000 kg Equipment: Rear axle hub reduction JSK 38C fifth wheel on sliding frame Danbox toolboxes behind cabin Mass switch Bullbar with lamps Automatic gearbox Intarder Push bar Cabin: XXL cab with high roof Cruise control Air conditioning 1 x Bed Cooler box Comfortable Seats Radio CD Player/Navigation = Further Information = General Information Year of manufacture: 2015 Lhedouu Hdiopfx Akkjn Transmission Gearbox: MAN TipMatic 12 30 OD, Automatic Axle Configuration Front axle: Tire size: 385/65R22.5; Max. axle load: 8,000 kg; Steered; Suspension: Parabolic suspension Middle axle: Tire size: 385/65R22.5; Max. axle load: 7,500 kg; Steered; Suspension: Air suspension Rear axle 1: Tire size: 315/80R22.5; Double tires; Max. axle load: 13,000 kg; Reduction: External planetary axles; Suspension: Air suspension Rear axle 2: Tire size: 315/80R22.5; Double tires; Max. axle load: 13,000 kg; Reduction: External planetary axles; Suspension: Air suspension Weights GVW: 41,000 kg Condition Technical condition: very good Optical condition: very good Damage: none Financial Information Price: On request

Condition: used, overall weight: 11,500 kg, first registration: 12/1994, Structure: Very good condition, fully extendable to a total length of 18.5 m. Lhjdszix Rqjpfx Akkjn

Condition: new, empty load weight: 10,900 kg, maximum load weight: 37,100 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 9,600 mm, loading space width: 2,540 mm, loading space height: 890 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, operation weight: 10,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, with a bevel at the rear of approx. 1,000 mm x 6° -Technical fifth wheel load: 18,000 kg -For tractor units: 4 x 2 and 6 x 2 Loading area: -Loading area, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6° -Loading area can be raised and lowered hydraulically after the gooseneck, length approx. 3,000 mm, load capacity up to approx. 9,000 kg -Grating and sheet metal floor approx. 5 mm as additional reinforcement on the bevel of the loading area Ramps: -A pair of two-part AXS steel ramps with a length of approx. 4,675 mm and a width of approx. 900 mm -Grating floor -Hydraulically hinged ramp tips -Ramps can be moved hydraulically by approx. 235 mm outwards and approx. 365 mm inwards -Painted sand coating on the outer frame of the ramp and on the ramp tip -Flashlights on the outside of the ramp tips with switch next to the ramp controls -Ramp secured in driving position using a quick release Axles, suspension and tires: -BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle with self-steering -1st Axle with traction aid -Operation via the brake pedal in the tractor unit -Technical axle load: 12,000 kg -Air suspension with lifting and lowering valve -235/75 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 -TPMS tire pressure monitoring sensors mounted in all wheels including spare wheels Braking system: -WABCO EBS-E brand braking system in accordance with EU regulations Paintwork: -Semi-trailer MB 7350 Nova gray Lsdpfx Aksuadk Nokshn Accessories included: -Bulkhead made of steel, plug-in, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -JOST module B - static test load = 50,000 kg -Continuous grating with 5 mm sheet metal underlay as additional reinforcement -Painted sand coating -Cutouts in the outer frame of the loading area and the lifting bed for hanging control valves for the hydraulic ramps on the right of the vehicle -2" kingpin -Central lubrication system with 1 pump, brand BEKAMAX -On the gooseneck 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized -Electric cable winch, approx. 5,400 kg pulling force, with radio remote control -Wire cable approx. 24 m long, cable ø approx. 9.5 mm, including cable pressure roller -WABCO Smart Board System -4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm