Low loader semitrailer

MEUSBURGER MTS3 12 t Achsen ,ausziehbar, gelenkt ,

Condition: new, empty load weight: 17,500 kg, maximum load weight: 43,500 kg, overall weight: 61,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,750 mm, loading space height: 400 mm, tire size: 245/70 R 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and lowered hydraulically -For tractor units: 6x4 or 8x4 Drop deck: -Low bed with external beams in extendable design, "SUPER LOW" design, length approx. 7,550 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking mechanism The supply lines are protected in the pull-out supports and automatically adjust to the respective drop-down bed length Rear chassis: -Rear chassis with closed outer frame, checker plate covering and continuous Prisma excavator trough approx. 1,450/900 x 505 mm, open at the rear -2 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame Axles and tires: -"PENDEL-AXLE", all axles with hydromechanical forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with stopcocks and locking pin for securing in raised position -Technical axle load: 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 / 3PMSF tires Accessories included: -Preparation for mounting bolt-on container positioners for 1x 20ft or 1x 40ft container on the outer beams -2" kingpin -One galvanized steel end wall approx. 400 mm high -One spare wheel with holder -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering can be operated from the front and rear by remote control cable via pushbuttons, with axle tracking control -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw coupling -Electric hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and red at the rear -2 wooden blocks 500x250x200 mm -European reflector plates (red/yellow) at the rear of the trailer -On the gooseneck and on the rear plate on the left and right, one holder each for the warning signs including socket -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 standard grease -Load manometer for determining the axle loads including load diagram -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,000 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,120 mm) Bedjh Hm Thspfx Ah Tjld -Separate air connection with air gun on the gooseneck -Duomatic air coupling from gooseneck to low bed -Gooseneck closed in the rear upper area with a removable cover -1 pair of steel ramps for bridging the mounting hooks of the low bed -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm -Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control 6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD rings VLBG-4 -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -folding extensions, approx. 230 mm on each side -A layer of sand painted onto the loading surface to prevent slipping Dipper arm recess of the rear chassis closed at the front and rear with a plug-in plate -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - aluminium 15%)

Condition: excellent (used), axle configuration: 3 axles, total length: 15,700 mm, total width: 2,750 mm, total height: 1,290 mm, suspension: air, tire size: 245/70R17.5, color: orange, Year of construction: 2010, Color: Orange Loading capacity: 40,600 kg Loading floor height: 54 cm Extendable Braked Main Features Manufacturer: Goldhofer Model: STZ VKL3 34/80 A Chassis Number: WG0STZV3590030501 Year of manufacture: 2010 Weights/Loading Capacity Fifth-wheel load: 24,000 kg Axle load: 11,200 kg Total axle load: 33,600 kg Gross vehicle weight (GVW): 57,600 kg Unladen weight: 17,000 kg Payload: 40,600 kg Axles Axle make: BPW ECO Air suspension All axles hydraulically steered High/Low valve AGS / ALB / ABS Tires: 245 / 70 R17.5, twin mounted Load index: 143/141G Dimensions Length: 15,700 mm – 26,000 mm Loading floor length: 6,600 mm Extension: 4,300 mm Extension beams: 6,000 mm Max. loading floor length: 16,900 mm Loading floor width: 2,750 mm Beam thickness: 380 mm King pin height: 1,295 mm Additional Information Operated via truck hydraulics Lashing rings Hydraulically operated gooseneck Detachable gooseneck Oversize load marker boards Rear bumper with lights King pin: 2.0'' Central lubrication Removable floor panels 4x extension crossbeams Toolbox at gooseneck = Further Information = General Information Year of manufacture: 2010 Axle Configuration Blodjuu Hifopfx Ah Tjd Tire size: 245/70R17.5 Axle make: BPW ECO Suspension: air suspension Rear axle 1: twin tires; max. axle load: 11,200 kg; steered Rear axle 2: twin tires; max. axle load: 11,200 kg; steered Rear axle 3: twin tires; max. axle load: 11,200 kg; steered Weights Unladen weight: 17,000 kg Payload: 40,600 kg Gross vehicle weight: 57,600 kg Functional Loading floor height: 55 cm Extendable body: Yes Condition Technical condition: very good Optical condition: very good Financial Information Price: On request

Condition: excellent (used), axle configuration: 2 axles, first registration: 03/2015, loading space length: 134,450 mm, loading space width: 2,550 mm, loading space height: 480 mm, suspension: hydraulics, Year of construction: 2015, Equipment: ABS, = Additional options and equipment = - Central lubrication = Further information = Axle configuration Bsdsvtc Aispfx Ah Tsld Suspension: hydraulic suspension Rear axle 1: Max. axle load: 12,000 kg; Steered Rear axle 2: Max. axle load: 12,000 kg; Steered Weights Unladen weight: 12,660 kg Payload: 34,340 kg Gross vehicle weight: 47,000 kg Functional Loading platform height: 48 cm Extendable body: Yes Condition Technical condition: very good Visual condition: very good Financial information Price: On request Further information Contact David F Middelman for more information.

Condition: used, empty load weight: 10,900 kg, maximum load weight: 43,600 kg, overall weight: 54,500 kg, axle configuration: > 3 axles, first registration: 04/2025, loading space length: 8,700 mm, loading space width: 2,550 mm, loading space height: 855 mm, tire size: 245/70 r17.5, color: grey, Year of construction: 2025, operation weight: 10,900 kg, Equipment: ABS, Gooseneck, rigid, in center tube design: -closed outer frame with cut-outs for lashing straps (LC 1,500 daN) -steel floor covering with anti-slip coating -including perforated strip for aluminum docking lights -2" kingpin -Mechanically operated BPW seat posts -550 mm long, 8' chamfer at the gooseneck end -Front wall incl. parking position for rear wall, 400 mm high -Spare wheel holder mounted upright on the front of the gooseneck -3 pairs of LC 5,000 daN lashing rings recessed in the loading area of the gooseneck -Aluminium plug-in drop sides 400 mm high, consisting of 2x drop sides, side length 3,150 mm and rear drop sides with stanchions (galvanized) -Rectangular storage box, aluminum, hinged lid, lockable Dimensions approx. 400 x 800 mm, center -Storage box 45', aluminum, hinged lid, lockable Dimensions approx. 400 x 800 mm, left -Storage box 45', aluminum, hinged lid, lockable Dimensions approx. 400 x 800 mm, right Loading area, easily telescopic: -closed outer frame with cut-outs for tension belts (LC 1,500 daN) -Fixed part at the front 700 mm Sheet metal floor covering with anti-slip coating -Angled interface between fixed section and loading area for attaching bridging rails and wheel recesses -Excavator trough incl. slotted holes for load securing (LC 1,500 daN), length approx. 3,850 mm -Preparation for hydraulic ramp (electrical supply) -spars for widening to 3,000 mm -Sloping vehicle rear 8°, 550 mm long -Carriage design for easy attachment and removal of ramps -Continuous mud flap at the rear -1 pair of LC 10,000 daN lashing points in the middle of the cargo bed behind the gooseneck -7 pairs of LC 10,000 daN lashing points in the outer frame of the cargo bed -6 pairs of stanchion pockets 100 x 50 mm in the outer frame of the cargo bed -1 pair of LC 10,000 daN lashing points in the center of the rear area of the cargo bed -1 pair of stanchion pocket strips approx. in the middle of the cargo bed -1 pair of stanchion pocket rails on the fixed part -1 pair of stanchion pocket rails behind the last axle Ramps: -Hydraulic double folding ramps, 2,750+1,500x800 mm -Wooden decking larch -Control via remote control (possible via cable and radio) -Ramps with quick-change (disassembly) system Chassis: -axle make BPW ECO Max Blsdpfxoi Ai E Re Ah Ted -2 ride heights -4 axles 10 t each (technically 12 t) -Twin tires 245/70 R17.5 -2 x rigid axle and 2 x friction-steered axle -Reverse steering lock on the friction-steered axle via reverse gear -Knorr brake system (in accordance with EU regulations with EBS-E) -TIM G2 from Knorr (trailer information module) -RSS (Roll Stability Support) driving stability control Load-dependent lift axle on the first axle incl. start-up aid (forced lowering of the lift axle possible via TIM) Accessories: -4 wheel chocks with holder 2 pairs of warning signs 423 mm x 423 mm, with 2 position lights and plug-in position for rotating beacon, infinitely adjustable up to 3,950 mm -Fastening options on the gooseneck and on the loading area (alternatively on the ramp, if available) are included -pluggable bulkhead plate at the end of the excavator trough -Electro-hydraulic unit for ramp operation -Ramp operation via radio remote control -Hydraulic relief supports at the rear of the vehicle for support during the loading process -1 Pair of additional reversing lights rear switched to reverse gear -Wooden widening planks - larch (optional)

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings Bsdpfx Ajrgzv Nsh Teld * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, 3-axle MULTIMAX PLUS low-bed semi-trailer, air-suspended and hydraulically forced-steered axles. Technical Data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h Legal Gross vehicle weight: 49,500 kg / 31,500 kg Fifth-wheel load: 18,000 kg Axle load: 31,500 kg / 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm King pin trailing radius (rearwards) approx.: 2,100 mm Saddle height loaded approx.: 1,205 mm Loading platform length approx.: 9,600 mm Extendable by approx.: ? Loading platform width approx.: 2,540 mm Loading height at max. load approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle spacing: 1,360 mm Gross vehicle weight depending on fifth-wheel load: Yes Special permit is required for exceeding country-specific regulations. Technical Description Bodpfxoizu Ntj Ah Teld Gooseneck: Gooseneck in SNT Design for optimized loading platform length, length approx. 3,900 mm, rear with chamfer approx. 1,000 mm x 6°. Technical fifth-wheel load: 18,000 kg. For tractor units: 4 x 2 and 6 x 2. Loading platform: Loading platform, length approx. 9,600 mm with rear chamfer approx. 900 mm x 6°. Loading platform behind the gooseneck hydraulically raisable and lowerable, length approx. 3,000 mm, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS A pair of two-part AXS steel ramps approx. 4,920 mm long and approx. 900 mm wide. Open grating surface. Hydraulically folding ramp tips. Ramps can be hydraulically shifted individually by approx. 235 mm outwards and approx. 365 mm inwards. Maximum load capacity and approach angle per technical data sheet: C470319 Maximum ramp angle with lowered loading platform: 9° Axles and Suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg Air suspension with lift/lower valve. Axle tool kit. Tyres: 235/75 R 17.5 3PMSF twin tyres. Manufacturer of our choice Load index 143/141J (144/144F) Braking system: WABCO EBS-E braking system according to EU regulations. Without connecting cable to tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" version as per EU regulations. (ASS 3) Metalizing: Complete HRM metalizing (High Resistance Metallisation) Complete steel structure shot blasted, then hot-finished with ZINACOR 850 (Zinc 85% - Aluminium 15%). Painting 6K final treatment: Complete steel structure shot blasted after welding. 1 coat zinc-based primer, 1 coat bonding primer. Final painting with 2 coats 2K (acrylic) single-colour in RAL shades of your choice, then cavity sealing with special wax. Rims in silver. Multi-colour and special painting at extra cost. Steel construction: Steel structure made of high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified to DIN-EN 287-1. MAG welding process to EN ISO 4063. Protective gas M21 per EN ISO 14175 Front wall of steel, plug-in, approx. 400 mm high Connection board for supply lines to the tractor unit at the height of the outer frame profile. ASPÖCK-UNIBOX at the front plug connection board with sockets 24N, 24S & 15-pin. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pin connection according to ISO-12098 If your pin configuration deviates from the ISO standard, please inform us. “Anderson” socket at the front connection board. Rema 78051-00 & Amp. 150 V. Cable for supply to electro-hydraulic unit and/or electric winch (35 mm²,

Condition: new, empty load weight: 15,550 kg, maximum load weight: 47,450 kg, overall weight: 63,000 kg, axle configuration: 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm -Rear gooseneck with bevel approx. 1,000 mm x 10° Loading area: -Loading area in extendable design, length approx. 8,800 mm, with bevel at the rear approx. 500 mm x 10° -One recess protruding into the loading surface and into the chamfer to accommodate the excavator dipper arm -Pneumatic locking with conical locking pins and reinforced locking positions -Hardwood covering on the bevel of the loading area Ramps: -1 Pair of two-part steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm -Ramps with hardwood decking -Hydraulically folding ramp tips Bodpfx Aok Aht Ush Told -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards -Square climbing ledges 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and suspension: -BPW axles and suspension, 1st axle with preload steering, all other axles with forced hydromechanical steering -Technical axle load: 12,000 kg -1st axle with electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -235/75 R 17.5 twin tires -TPMS tire monitoring system in accordance with ECE R141 -TPMS tire monitoring sensors mounted in all wheels including spare wheels Accessories included: -steel front wall, pluggable, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Parking position on the gooseneck for the warning signs when not in use -1 Spare wheel -On the gooseneck 1 pair of plug-in ALU side panels, approx. 400 mm high, anodized -One plug-in ALU rear panel on the gooseneck, approx. 400 mm high, anodized -Approx. 40 mm thick hardwood covering over the gooseneck, checker plate covering over the kingpin -2" kingpin -Guide plate from the gooseneck for the saddle plate, approx. 500 mm wide -4 wheel chocks -Mechanical seat posts with 2-speed gearbox and crank -JOST module B - static test load = 50,000 kg -1 Intermediate table, approx. 300 mm wide -Widenings (galvanized) extendable by approx. 230 mm per side -Wheel recesses with square climbing rails -ALU covers for the wheel recesses -1 pair of mechanical rear supports -Steering can be operated from the front and rear by cable remote control, with tracking control of the axles -1st axle with automatic lift axle function -Central lubrication system with 1 pump, BEKAMAX brand -Radio remote control for operating the self-steering, in addition to the cable remote control, with 2 indicator lights on the receiver as toe-in control -Wabco Smart Board System -4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for rotating beacon

Condition: new, maximum load weight: 31,500 kg, overall weight: 42,000 kg, axle configuration: 3 axles, Year of construction: 2025, Equipment: ABS, Wiese 3-axle semi-trailer with lift table and fold-down rear. Ideal for transporting forklift trucks and/or work platforms. Technical data. 3 x 10 to. axles Lift axle Bedpfx Ahjvw Hmto Tsld Steering axle Smart Steering (steers forwards and backwards) Outer beam chassis with slope 18-tonne neck design suitable for 2- and 3-axle semitrailer tractors Lifting table hydraulically movable in 3 positions Rear in folding rear design incl. hydraulic extensions, can be used as drive-on ramps, drive-over ramps or as a loading area (overall length reduction when rear is raised) Remote control for ramps and lift table Front wall Grid floor Numerous lashing points SmartBoard Central lubrication system Spray-galvanized and painted steel construction Numerous optional extras are available: e.g: Cable winch Storage box on the saddle step aluminum rims Further information on request.

Condition: new, maximum load weight: 65,400 kg, overall weight: 93,400 kg, axle configuration: > 3 axles, Year of construction: 2025, Pos 1. Type STZ-VP 6 (245) (2+4) with pendle axles The specified technical data are only valid when used with a 4-axle tractor unit with the following specifications: Dimension a: 5,400 mm Saddle height (loaded): 1,300 mm Weights Speed: 80 km/h - Fifth wheel load: 22,000 kg - Axle load: 6 x 12,000 kg - Permissible total weight: 94,000 kg - Tare weight approx.: 29,600 kg - Payload approx.: 64,400 kg (depending on load chart / easyLOAD calculation) Dimensions - Dimension b: 18,765 mm - Overall train length: 24,165 mm - Vehicle width: (please specify) - Gooseneck length x width: 3,700 mm x 2,480 mm - Saddle height (loaded): 1,300 mm - Steering lock radius front/rear: 1,370 mm / 2,735 mm - King pin: 3.5'' Front 2-axle chassis - Wheelbase: 1,510 mm - Single tires: Continental, 245/70 R 17.5 143/141 L (146/146 F) M+S - Steering axle arrangement: counter-steered 14,400 mm flatbed (outer beams) single extendable with split - Length x width: 7,000 mm x 2,750 mm - Extendable by / to max.: 3,400 mm / 10,400 mm - Deck height: 300 mm Blsdpfxjwg N N Ij Ah Tod - Plus 4,000 mm extension beam incl. - Loading height, loaded: approx. 450 mm Rear 4-axle chassis - Wheelbase: 3 x 1,510 mm - Single tires: Continental, 245/70 R 17.5 143/141 L (146/146 F) M+S - Steering axle arrangement: forced steering

Condition: new, maximum load weight: 38,100 kg, overall weight: 50,000 kg, axle configuration: > 3 axles, loading space length: 13,100 mm, loading space width: 2,480 mm, loading space height: 760 mm, suspension: air, tire size: 205/65 R17.5 3PMSF, color: grey, Equipment: ABS, Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10° 3 pairs of lashing rings Hardwood decking 30 mm thick Loading area: 5 pairs of lashing rings can be folded outwards 3 pairs of lashing rings can be folded outwards 1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Seat posts: JOST seat posts with 2-speed gearbox for 24 t lifting capacity Axles and tires: BPW axles, two axles rigid two axles self-steering, air-sprung, with drum brake, with raise/lower function The self-steering axles with electromagnetic reverse lock can be activated via reverse gear or manually Axle tool Tires 205/65 R17.5 3PMSF Brake system: WABCO brake system in accordance with EU regulations with EBS-E Steel construction: Steel construction made from high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Electrical equipment: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO Paintwork: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component zinc dust primer A high-quality 2-component Top coat single color in MB 7350 nova grey No metallic paint finish possible Rear section metallized and painted in RAL 9010 Accessories included: 1 spare wheel 205/65 R 17.5 TPMS tire pressure monitoring system in accordance with ECE R 141 Yellow-red air couplings on the galvanized connection strip at the front 4 brake shoes with holder on the bulkhead Mounting in the rear area of the gooseneck for ALU docking lights Galvanized folding supports under the bevel of the cargo bed A holder for a rotating beacon at the rear of the trailer Height-adjustable tarpaulin body Galvanized bulkhead with a tensioning mechanism for the sliding curtains Height-adjustable by approx. 400 mm "EDSCHA" brand roof can be moved forwards on ALU roof rail profiles bolted to the front and rear wall 3 pairs of sliding stanchions in the loading area The body can be hydraulically widened at the rear to the left and right by approx. 750 mm Sliding roof with pivoting portal support Sliding tarpaulin with 700 mm reserve in length, with tension belts at approx. 600 mm intervals Height top edge of body approx. 3,960 mm Driving with the sliding tarpaulin open is not permitted and will damage the tarpaulin Suspension strip for ALU docking lights at the rear of the vehicle A holder for the warning signs including socket on the gooseneck and on the rear panel on the left and right respectively A mud flap at the rear of the trailer European reflector plates at the rear of the trailer 7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load condition Blodpotphtmefx Ah Ted Rear body closed with ALU hinged doors A layer of sand painted onto the chequer plates on the gooseneck and on the cargo bed to prevent slipping BEKAMAX central lubrication system with NLGI-2 standard grease and removable protection around the pump Speed sticker 80 km/h at the rear and on both sides Load manometer to determine the axle loads including load diagram