Low loader

Nükte Trailer NEW Lift+Steering Axle Ramps

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) Fodorgzv Njpfx Ah Dopc * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2025, 3-axle MULTIMAX *PLUS semi-trailer low loader, air-suspended and hydraulically forced steered axles. Technical data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h Legal Total weight: 49500 kg 31500 kg Fifth wheel load: 18000 kg Axle load: 31500 kg 31500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm King pin turning radius to the rear approx.: 2,100 mm Fifth wheel height when loaded approx.: 1,205 mm Loading area length approx.: 9,600 mm Extendable by approx.: * Loading area width approx.: 2,540 mm Loading height with max. load approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle distance: 1,360 mm *Total weight depends on the fifth wheel load: Yes Special permit required if the country-specific legislation is exceeded: Technical description Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,900 mm, with a bevel at the rear approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor units: 4 x 2 and 6 x 2. Loading area: Loading area, length approx. 9,600 mm with a bevel at the rear approx. 900 mm x 6°. Loading area can be raised and lowered hydraulically after the gooseneck, length approx. 3,000 mm, load capacity up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS A pair of two-part AXS steel ramps with a length of approx. 4920 mm and a width of approx. 900 mm. Open grating surface. Ramp tips that can be opened hydraulically. Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 365 mm inwards. Maximum load and ramp angle according to technical data sheet: C470319 Maximum incline angle with lowered loading area: 9° Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced steered. Technical axle load: 12,000 kg Air suspension with lifting and lowering valve. Axle tool. Fsdpfxoizu Nte Ah Depc Tires: 235/75 R 17.5 3PMSF twin tires. Make of our choice Load index 143/141J (144/144F) Brake system: WABCO EBS-E brake system in accordance with EU regulations. Without connection cable to the tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Version in accordance with EU regulations. (ASS 3) Metallization Complete HRM metallization (High Resistance Metallization) Complete steel construction shot blasted, then hot-finished with ZINACOR 850 (zinc 85% - aluminum 15%). Paint 6-K final treatment: Complete steel construction shot blasted after welding. 1 layer of zinc-based base paint, 1 layer of adhesion primer. Final painting with 2 layers of 2-component paint (acrylic) in a single color in RAL colors of your choice, then sealing the cavities with special wax. Rims in silver. Multi-color and special painting for an additional charge. Steel construction: Steel construction made of high-strength fine-grain steel. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welder tested according to DIN-EN 287-1. MAG welding process according to EN ISO 4063. Protective gas M21 according to EN ISO 14175 iFront wall made of steel, pluggable, approx. 400 mm high Connection strip for supply lines to the SZM, attached at the height of the outer frame profile. i ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets 24N connection in accordance with ISO-1185 24S connection in accordance with ISO-3731 15-pin connection in accordance with ISO-12098 If your pin assignment differs from the ISO connection standard, please let us know. i "Anderson"

Condition: new, maximum load weight: 31,500 kg, overall weight: 42,000 kg, axle configuration: 3 axles, Year of construction: 2025, Equipment: ABS, Wiese 3-axle semi-trailer with lift table and fold-down rear. Ideal for transporting forklift trucks and/or work platforms. Technical data. 3 x 10 to. axles Lift axle Steering axle Smart Steering (steers forwards and backwards) Outer beam chassis with slope 18-tonne neck design suitable for 2- and 3-axle semitrailer tractors Lifting table hydraulically movable in 3 positions Rear in folding rear design incl. hydraulic extensions, can be used as drive-on ramps, drive-over ramps or as a loading area (overall length reduction when rear is raised) Remote control for ramps and lift table Front wall Fpedpfjvw Hmtjx Ah Dsc Grid floor Numerous lashing points SmartBoard Central lubrication system Spray-galvanized and painted steel construction Numerous optional extras are available: e.g: Cable winch Storage box on the saddle step aluminum rims Further information on request.

Condition: ready for operation (used), functionality: fully functional, empty load weight: 7,400 kg, maximum load weight: 29,400 kg, overall weight: 36,800 kg, axle configuration: 3 axles, first registration: 09/1997, loading space length: 1,360 mm, loading space width: 2,550 mm, loading space height: 850 mm, suspension: air, tire size: 245.70 R 17.5, tire condition: 70 %, ground clearance: 850 mm, color: orange, Year of construction: 1997, Equipment: ABS, tail-lift, Used De Angelis low-loader semi-trailer with winch, 3 axles (3rd steering), air suspension, ABS, gooseneck chassis with twin full-width electro-hydraulic rear ramps, hydraulic winch under the neck (max. 24 tons), lowered deck section 9.95 m long x 85 cm from the ground, aluminum side boards 70 cm high, opening and removable, year 1997, inspected until 31/12/2026 – DEALER INTERDRIVE SRL – PARMA Fsdpfx Aex H S Awjh Djpc

Condition: used, empty load weight: 9,480 kg, maximum load weight: 31,520 kg, first registration: 03/2020, next inspection (TÜV): 04/2024, total length: 11,500 mm, total width: 25,500 mm, total height: 38,000 mm, suspension: air, tire size: 245/70 R 17.5/10mm, wheelbase: 1,800 mm, front tire size: 245/70 R 17.5/10mm, operation weight: 41,000 kg,

Condition: new, empty load weight: 10,900 kg, maximum load weight: 37,100 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 9,600 mm, loading space width: 2,540 mm, loading space height: 890 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, operation weight: 10,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, with a bevel at the rear of approx. 1,000 mm x 6° -Technical fifth wheel load: 18,000 kg -For tractor units: 4 x 2 and 6 x 2 Loading area: -Loading area, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6° -Loading area can be raised and lowered hydraulically after the gooseneck, length approx. 3,000 mm, load capacity up to approx. 9,000 kg -Grating and sheet metal floor approx. 5 mm as additional reinforcement on the bevel of the loading area Ramps: -A pair of two-part AXS steel ramps with a length of approx. 4,675 mm and a width of approx. 900 mm -Grating floor -Hydraulically hinged ramp tips -Ramps can be moved hydraulically by approx. 235 mm outwards and approx. 365 mm inwards -Painted sand coating on the outer frame of the ramp and on the ramp tip -Flashlights on the outside of the ramp tips with switch next to the ramp controls -Ramp secured in driving position using a quick release Axles, suspension and tires: -BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle with self-steering -1st Axle with traction aid -Operation via the brake pedal in the tractor unit -Technical axle load: 12,000 kg -Air suspension with lifting and lowering valve -235/75 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 -TPMS tire pressure monitoring sensors mounted in all wheels including spare wheels Braking system: -WABCO EBS-E brand braking system in accordance with EU regulations Paintwork: -Semi-trailer MB 7350 Nova gray Accessories included: -Bulkhead made of steel, plug-in, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -JOST module B - static test load = 50,000 kg -Continuous grating with 5 mm sheet metal underlay as additional reinforcement -Painted sand coating -Cutouts in the outer frame of the loading area and the lifting bed for hanging control valves for the hydraulic ramps on the right of the vehicle -2" kingpin -Central lubrication system with 1 pump, brand BEKAMAX -On the gooseneck 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized -Electric cable winch, approx. 5,400 kg pulling force, with radio remote control -Wire cable approx. 24 m long, cable ø approx. 9.5 mm, including cable pressure roller Fedpjuadk Nefx Ah Dopc -WABCO Smart Board System -4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Condition: used, maximum load weight: 42,500 kg, overall weight: 60,000 kg, axle configuration: 3 axles, first registration: 06/2022, with 12 axles, hydraulically suspended and divided, with hydromechanical forced steering, rear taper and drive-on ramps STZ-L Gooseneck - Robust welded steel construction - Engineered loading platform 3,950 x 2,480 mm including rear taper - Hydromechanical forced steering (dual-circuit steering system) - Turntable-mounted fifth-wheel plate with interchangeable 2-inch or 3.5-inch kingpin and adjustable steering wedge - Fifth wheel load: 24 t - Rear max. steering radius: 2,600 mm Loading platform - Lowered outer sections 4,630 mm long, 420 mm deep, resulting in a loading height of 470 mm or 830 mm with floor inserts - Extendable by 2,053 mm - Includes aluminum bridging rails for creating level surfaces - Excavator boom trough at rear running gear: 4,900 mm long, 880 mm wide, 480 mm deep - Length of rear running gear: 4,900 mm incl. 500 mm rear taper, loading height 890 mm - One pair of wheel recesses in lower deck - 3-axle hydraulically suspended running gear - Split Gigant axles with 600 mm stroke Rear of vehicle - Tapered design, 500 mm - Rear hydraulic support Drive-on ramps - Two-part drive-on ramps, 2,850 + 1,850 mm long, 800 mm wide - Rubber-coated with climbing bars Braking system Fpodpfew Etd Tox Ah Doc - Dual-line full air braking system with diaphragm brake cylinders - Automatic load-dependent brake (ALB) - Automatic slack adjusters (AGS) - Parking brake via spring-loaded cylinders - ABS brake Special equipment Radio remote control for steering and ramp operation Central lubrication system Technical data Gooseneck Loading platform (LxW): 3,950 x 2,480 mm Loaded fifth wheel height: 1,300 mm Loading platform Platform (LxW): 10,030 x 2,850 mm, extendable by 2,053 mm Lowered outer sections: 4,630 mm + 2,053 mm extension Center beam: 980 mm Excavator trough: 4,900 mm long, 880 mm wide, 480 mm deep Steering 1st to 3rd axle: hydromechanically forced steered (dual-circuit system)

Condition: new, maximum load weight: 36,937 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer low loader with hydr. gooseneck Available immediately! TECHNICAL DATA: * Semi-mounted height 1,250 mm * Outer length 13,190 mm * Gooseneck length 3,950 mm * Platform length 9,240 mm * Platform height 875 mm * Wheelbase 8,480 mm * Wheelbase 1,360 mm * Axle load 30,000 kg * BPW axles with air suspension and drum brakes, 10 tons load capacity * Unladen weight 11,063 kg * Overall width 2,550 mm * Permissible gross weight (60 km/h) 52,800 kg * Permissible gross vehicle weight (80 km/h) 48,000 kg CHASSIS: * 2x rigid axles at the front, 1x self-steering axle at the rear * Overload-dependent manual axle lift system on the 1st axle * 12-wheel tires 245/70R17.5 * Air suspension, 1x load pressure gauge CHASSIS: Made of high-quality and high-strength S700 MC steel * Gooseneck with 90° vertical corners * Jost supports at the front * Folding rear supports * Grid floor RAMP: * Drive-on ramp capacity 40 tons * 2x hydraulic ramps, suitable for hydraulic sliding/folding operations with galvanized steel surface, 4,200 mm length and 850 mm width, 9 degree ramp angle, load capacity 40,000 kg and 3,510 mm height in closed position Fpjdpfx Ahot Aqv Se Dec * Hydraulic gooseneck ramp 2,800 mm long 10° angle LOAD SECURING: * Lashing rings 6x2 on the gooseneck with 6 tons capacity, 6x2 on the platform with 6 tons capacity, 8x2 on the outer frame with 6 tons capacity * 8x2 stanchion pockets MISCELLANEOUS: * 1x rotating beacon * 1x work light * 2x2 extra-wide boards with lighting * SmartBoard For further information please do not hesitate to contact us

Condition: used, empty load weight: 6,000 kg, first registration: 03/2026, total width: 25,500 mm, suspension: air, tire size: 385/65R22.5, front tire size: 385/65R22.5, operation weight: 35,000 kg,

Condition: new, maximum load weight: 25,645 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete stock of immediately and soon-to-be available vehicles on our website. Excerpt from equipment specification. Complete specification available on request. Load area: - Low-bed design with central beam, extendable version, approx. 6,750 mm in length - 5 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the loading platform (LC 10,000 daN) Gooseneck: Fpodpfxjxf Silj Ah Doc - Hydraulic lifting/lowering gooseneck, detachable Rear chassis: - Short rear chassis with closed outer frame and checker plate covering - Chassis with excavator trough, closed in the rear half for housing the air tanks - 2 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Air suspension with raise/lower control valve Tyres: - Tyres 245/70 R 17.5, 3PMSF - TPMS: Tyre Pressure Monitoring System according to ECE R 141 Brake system: - Wabco braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality single-tone 2-component (2K) top coat in RAL 3000 Flame Red Including the following additional equipment: - 2 kingpins - Galvanised steel front wall, approx. 400 mm high - Remote steering from front and rear, operated by cable remote control with push buttons, including single tracking control for the axles (no installation in the tractor unit) - Electro-hydraulic unit - Axle load gauge including load diagram - On the gooseneck, removable aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). Rear galvanised stake pockets are removable. (Body length approx. 2,560 mm) - Separate air connection with air gun on the gooseneck - 2 work lights with switch on the trailer, mounted on the left and right of the gooseneck platform - 1 INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck - 6 pairs of stake pockets for insertable posts approx. 100 x 50 mm in the outer frame of the load area, 2 pairs in the chassis outer frame - Galvanised, extendable width extensions approx. 230 mm per side - Hydraulic connections from gooseneck to low bed with multi-coupling (instead of screw couplings). No seal guarantee included. - Central lubrication system with 2 BEKAMAX (Pico) pumps, standard NLGI-2 grease, with removable protection around the pump - 2 pairs of WADER container locks on the loading area, for 1x20' container - 1 removable galvanised intermediate table with 1 pair of WADER container locks - 1 pair of steel ramps for bridging the low bed’s hook mountings - Anti-slip sand-coated layer painted on the load area - HRM Metallisation (High Resistance Metallisation)