Used Fliegl Dolly Mega Trailers for sale (303)

Condition: new, machine/vehicle number: 5c7120ea17bcf92d3b69899da, empty load weight: 14 kg, maximum load weight: 35 kg, overall weight: 50 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with exchangeable 2 king pins 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2x wheel chocks with holder Aluminum side collision protection Quarter-shell mudguards in front of and behind axle unit with spray flaps behind each axle 1x storage box Box, w=2 350 mm x l=730 mm x h=640 mm, bolted transversely at the front to the floor of the gooseneck, with 2 storage trays Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks on gooseneck, front transverse Wooden planks 70 mm for widening to 3000 mm Excavator trough above the rear axles starting to the rear, approx. 500 mm wide and approx. 230 mm deep Low loader lashing eyes 3 pairs of lashing eyes per 10 tons at the front gooseneck, 8 pairs of lashing eyes per 10 tons in the low bed, 3 pairs of lashing strips in the tramline area of the low bed, 3 pairs of lashing eyes per 10 tons in the axle/rear area Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Hydraulic forced steering via saddle deflection wedge acting on all 3 axles, Post-steering with radio remote control + auto toe-in, (up to max. 20 km/h)Note! A 2-pin Nato socket with at least 2 x 35 mm² is required in the truck for the power supply to the steering system. Power is supplied to the pump unit via a Nato connection cable to the towing vehicle, without truck installation (re-steering must be used once a week). Air suspension Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, without connecting cable With lifting & lowering valve, hold function in lowering position + auto-reset function Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Dedoi Ri Hgopfx Afmekw Vehicle driving stability system Trailer Infocenter, for displaying vehicle data such as axle loads (no calibrated scales), mileage and diagnostic/system messages. Electrics 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white LED position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1x additional LED work light(s) at the rear, switched via reversing light 1x LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Gooseneck with steel / checker plate covering In the tramline area with 70 mm softwood floor, in the wheel housing area with steel / checker plate covering, low bed can be raised hydraulically on the left and right in the tramline area for entry, via truck auxiliary drive Rear slope with 70 mm softwood floor Drop deck length approx. 6,300 mm Drop sides 25 mm aluminum h

Condition: new, machine/vehicle number: d461243f559015adca5bb372c, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 Dedpfsi Ri Dlex Afmokw at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco, Knorr or Haldex Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: 7383bc2b7f580f0cb319b52f7, empty load weight: 5,300 kg, maximum load weight: 29,700 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Surface stone-repellent Splash guard behind last axle in asphalt version, attached to mudguard with hinge, with attachment option on top of mudguard, shortened mudguard Tow hook at the rear Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights Dodpfx Afji Rix Iomjkw 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics High-pressure cylinder max. 250 bar, with HDK screw socket, fixed part, NW 48 mm (without hose connection) Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Membrane rear wall Rear wall as pendulum flap, resting on the outside with 2-fold hook locking. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Insulated body, Fliegl Asphalt Profi Thermo, body insulated at the front, sides, bottom and rear with Fliegl Isotherm. BASIC cover, tarpaulin cladding Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) Body strength according to EN 12642 24/7 service hotline Manufacturer certificate for thermal vehicles according to RS 10 - 2013 Prepared for single-line license plate holder Contour marking

Condition: new, machine/vehicle number: d7a33d709a92cd60f18d010e8, empty load weight: 3 kg, maximum load weight: 14 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 385/65 r22.5, Further information Chassis Wechel central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 1 pair of front gear support legs, with straight lower section and single-sided operation in FR right 2 wheel chocks with holder Aluminum side impact guard Side collision protection set inwards, for optimum clearance to the swap body supports Steel underride guard Half-shell mudguards Spray flaps Towing device central axle trailer Drawbar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or precise testing still required in the event of an order) Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Air supply 208 liters Spring-loaded parking brake 2 swap-proof coupling heads at the front, with connecting lines to the engine trolley, connection in FR right-hand side EBS, electronic brake system with EBS plug at the front, with connecting cable, connection in FR right-hand side Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in both lowering / lifting position Wheels and tires 385/65 R22.5 Athos brand Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin plug at the front, with connecting cable, connection in FR right-hand side 2 additional LED work lights, integrated at the rear, switched via reversing light 1 LED work light at the front, centered between the carriers, radiating to the rear, switched via reversing light Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Dkodpei Riwbjfx Afmew Attention: Archive pictures!

Condition: new, machine/vehicle number: 06017a31026c05fc8f6ccf5ae, empty load weight: 3,055 kg, maximum load weight: 14,945 kg, overall weight: 18,000 kg, axle configuration: 2 axles, tire size: 235/75 r17,5, Further information Chassis Changing turntable Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 Turntable with sturdy ball bearing slewing ring 2 wheel chocks with holder Aluminum side bumper Steel underride guard Quarter-shell mudguards at the front and half-shell mudguards at the rear Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the motor vehicle, EBS, electronic braking system with EBS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in both lowering and lifting position Wheels and tires 235/75 R17.5 tires of the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights in LED with resistor, amber LED lighting at the side, license plate lighting in LED, (Note! with certain towing vehicles, misdiagnosis may occur although the function is given) 2 white front position lights in LED 2 white/red rear lane departure lights in LED 1 x 15-pin plug at the front, with connecting cable, Additional LED work light(s) at the rear, switched via reversing light Dodpfxoi Ri Rcj Afmjkw Approval / plates Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Attention: Archive pictures!

Condition: new, machine/vehicle number: dc46d2e1cd272305b99fb3160, empty load weight: 9,800 kg, maximum load weight: 31,200 kg, overall weight: 41,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Vehicle consisting of: Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with interchangeable 2 kingpin and 2 kingpin positions 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2 wheel chocks with holder Aluminum side collision protection Quarter-shell mudguards in front of and behind axle unit 1st pair of wheel recesses after gooseneck recessed in the low bed of the tramline area, slanted towards the entrance. Length at bottom approx. 1600 mm, depth of wheel recesses approx. 260 mm. Note! Frame in main beam area 260 mm higher than wheel recess. 2nd pair of wheel recesses between A and B axle. Bottom length approx. 350 mm, depth approx. 260 mm. Note! Frame in main carrier area 260 mm higher than wheel recess. If wheel loaders are to be driven and the overall height is to be checked, we request a technical data sheet for the wheel loader types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses are required by the customer). Wheel recess cover can be pulled out from the main frame, with wooden inserts. Dkedpfxei Ri Hce Afmjw Widenings extendable to 3,000 mm (not in the rear slope and not in the wheel recesses below) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks on gooseneck, front transverse Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 2 pairs of ring lashing eyes, 5 tons each at the front on the gooseneck 11 pairs of lashing rings at the top and sides, each 10 tons, embedded in the outer frame 2 x on gooseneck9 x in low loader bed distributed first lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 8 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, or instead of stake pockets 5 to. Ring lashing eyes embedded in the floor Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, without connecting cable with lifting & lowering valve Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle - driving stability system Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1 x LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm, removable with plug Floor Gooseneck with steel / checker plate covering Storage box embedded in drive-over slope to gooseneck Then with 70 mm softwood floor, in the wheel recesses underneath and in the wheel

Condition: new, machine/vehicle number: 628cde0fe99cc2d3c8eaa8dd8, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) Dkodpfx Asi Ri Ddsfmjw 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: 113bec9dd54d24fa34a088424, empty load weight: 4,400 kg, maximum load weight: 27,600 kg, overall weight: 32,000 kg, axle configuration: 2 axles, tire size: 385/65 r22,5², Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires Dsdpfx Aji Rizisfmekw 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10 J

Condition: new, machine/vehicle number: 42a74cba14ef2bfc0e90e52b2, empty load weight: 6,800 kg, maximum load weight: 28,200 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Welded fine-grained steel construction, lightweight design, fifth wheel plate with interchangeable 2 bolsters with hydr. mounting for Horsch Trailer Lift. Curved front end, hydraulic support legs, wheel chocks with holder, side collision protection special design, underride guard, foldable, quarter-shell mudguards in front of and behind axle unit, with anti-spray flaps only on last axle, stainless steel storage box W=800 /H=350 / D=350, tarpaulin pole with holder, towing hook at rear Dsdsi Rix Dspfx Afmskw Axles+suspension BPW disc brake axles with 430 mm disc diameter, axle/chassis laser-measured to reduce tire wear and fuel consumption, air suspension with safety cables, 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake system, spring-loaded parking brake, 2 swap-proof coupling heads at the front, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5, steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable sockets at the front, without connecting cable, 2 additional LED work lights at the rear, switched via reversing light, night lighting via radio remote control. Hydraulics Low-pressure cylinder max. 170 bar, with HDK screw socket, fixed part, NW 48 mm (without hose connection), hydraulic actuation via truck power take-off, hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nutThe hydraulics for the lowerable side wall FR-left and the trailer lift arms are switched off automatically from approx. 20 km/h. The trailer lift arms can be locked separately so that the vehicle can only be unhitched. Body Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external cylinder holder. Side walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk-repellent top rail profile. Side wall in FR-left at the top approx. 7700 mm long and can be lowered hydraulically by approx. 600 mm in height for loading. Note! Only 2 positions possible, either completely closed or completely lowered. Before lowering the side wall, the roller tarpaulin must be opened and the crossbars inserted into the parking positions in FR-right or completely removed. Shovel and broom holder on the outside of the front wall. Inside with access to front wall. Greenline - conical and aerodynamic trough shape Swinging rear wall with 2 grain slides. Rear wall can be raised hydraulically by approx. 950 mm for unloading. Rear wall with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access ladder Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left. Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible, depending on the load.

Condition: new, machine/vehicle number: 1e7fb50bfb3671204fb4d0b92, empty load weight: 4 kg, maximum load weight: 33 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/55 r22.5, Further information Chassis Saddle Container Fine-grained steel welded construction, saddle plate with interchangeable 2 kingpins and 2 kingpin positions Container mounts: 1 x 20 feet in the middle without steel/checker plate covering in the rear area 2 x 20 feet or 1 x 40 feet with gooseneck tunnel without height adjustment at the rear and without folding center supports, no transport of containers without tunnel possible. 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Dkjdei Riv Njpfx Afmew Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EG Impact protection at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/55 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, rear and brake lights in LED, amber LED lighting on the side (Note! with certain towing vehicles, misdiagnosis may occur, although the function is given) 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 2 additional LED work lights at the rear, switched via reversing light Operating instructions Attention: Transport of filled tank containers is excluded! Country of registration / plates Germany with Dekra approval and certificate (according to §13 EG - FGV) Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Attention: Archive pictures!

Condition: new, machine/vehicle number: 1acf251a278ec5cde4067a7b1, empty load weight: 5,800 kg, maximum load weight: 22,200 kg, overall weight: 28,000 kg, axle configuration: 2 axles, tire size: 235/75 r17,5, Further information Chassis saddle forwarding Fine-grained steel welded construction, saddle plate with replaceable 2 king pins Outer frame slightly slanted new design with Load-Lock profile for tensioning strap attachment 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Free support foot corner dimension or free swing radius to the rear approx. 1920 mm 2 wheel chocks with holder Aluminum side impact guard Steel underride guard Quarter-shell mudguards in front of and behind each axle 1 spare wheel holder for 1 e-wheel, with wheel fastening set 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Axles + suspension Drum brake axles of the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-applied parking brake Duomatic connection at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 235/75 R17.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides Dkjdpfjkv Uvzex Afmsw 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin socket at the front, without connecting cable Floor Screen printing plates approx. 30 mm thick, for high point load capacity for forklift axle load up to max. 5,600 kg Front wall / front corner stanchions 25 mm aluminum hollow profile, approx. 1 350 mm high, steel corner stanchions in volume design Approval country / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Front wall aluminum Attention! These are archive pictures!

Condition: used, machine/vehicle number: 0e87837859aec926e9db10456, empty load weight: 6,200 kg, maximum load weight: 11,800 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 05/2018, tire size: 235/75 r17,5, Year of construction: 2017, Further information Chassis: Welded steel construction, double offset with drop deck in front of and behind axle unit, drop deck slanted towards entrance, turntable with strong ball bearing slewing ring, folding rear support, wheel chocks, side collision protection, quarter-shell mudguards Lashing eyes: above front axle: 2 pairs of ring lashing eyes per 5 tons at the front on the offset drop deck/rear axle: 6 pairs of lashing eyes laterally in the drop deck per 8 tons, 6 pairs of lashing eyes per 5 tons between the side members, pair of stake pockets embedded in the outer frame, inside 70 x 40 mm, or instead of stake pockets, 5 tons ring lashing eyes embedded in the floor. Ring lashing eyes embedded in the floor Dksdpei Ri N Ujfx Afmjw Drawbar: tested 40 mm drawbar eye Axles: BPW drum brake axles Brake system: 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable front coupling heads Electrical system: 24 volt, multi-chamber lights, amber lighting at the sides, 2 white position lights at the front 2 white/red lane departure lights at the rear, rotating beacon with holder, pair of warning signs illuminated and extendable to 3,000 mm, 2 x 7-pin interchangeable plugs at the front Floor: Front offset with steel / checker plate covering, storage box recessed in drive-over slope to offset, tramline area and in the middle between the beams with steel / checker plate covering, rear slope with 70 mm softwood floor, deep loading area incl. rear slope 5900 mm Drive-on ramps: Hook-in strip for aluminum ramps across the entire width. as U-profile across the entire width Pair of aluminum ramps 800 mm long, approx. 400 mm wide, load capacity per pair 14,000 kg, Storage compartment for ramps between the beams Approval: contour marking with reflective strips to ECE R 048, white at the sides and red at the rear

Condition: new, machine/vehicle number: 408ba9a39bbb8087056d6e563, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3,000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed Dodoi Ri Daepfx Afmskw 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° / D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel housing area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of approval / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized

Condition: new, machine/vehicle number: 2f960ff7c44de83fd060ec5df, empty load weight: 6,750 kg, maximum load weight: 28,250 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only Tarpaulin pole with bracket Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection) Hydraulic actuation via truck power take-off Troughs Round steel body in light Master Agrar design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Aluminum rear wall on pendulum bearings with double-joint hinge and with 2-leaf door division 1/2 to 1/2, top with swinging gallows, with one grain slider per door. With external espagnolette lock and mechanical locking at the bottom, Side walls 3 mm thick throughout, base 3 mm thick throughout, wear and weight-optimized design, Standing platform with ladder, connection plate for air/electric and brake with large clearance for best possible operability. Djdei Rizfjpfx Afmekw Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10 J

Condition: new, machine/vehicle number: 11be0b1246b37a0869e99ab60, empty load weight: 5,100 kg, maximum load weight: 29,900 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5², Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system Djdpfx Afoi Rixyomekw 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Support bracket

Condition: new, machine/vehicle number: 7272fc3b6a97f9be58a222f05, empty load weight: 5 kg, maximum load weight: 32 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis Saddle Container Fine-grained steel welded construction, fifth wheel plate with interchangeable 2 kingpins and 2 kingpin positions Front locking on tipping ram support frame with incl. guide wedges on both sides Incl. guide wedges, rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Container mounts: Locking cross member, 2-fold for locking 1 x 30 foot or 1 x 40 foot container. Adjustment via central telescope as an interlocking central tubular frame Dksdpfxoi Riv Ej Afmew with bolt lock. Optimum fifth wheel load when transporting 30 foot and 40 foot containers. 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EG Hydraulics 100 Low-pressure cylinder max. 150 bar, with HDK screw socket, fixed part, NW 48 mm. (without hose connection) Hydraulic actuation via truck power take-off Incl. Hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nut Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension Brake system 170 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake Tele Control Axle relief for easy telescoping 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck instal. calibrated scales) Wheels and tires 385/65 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 2 additional LED work lights at the rear, switched via reversing light

Condition: new, machine/vehicle number: d24246f092ae53c0e155d19dd, empty load weight: 2,400 kg, maximum load weight: 13,600 kg, overall weight: 16,000 kg, Further information Chassis tandem trailer Welded steel construction with approx. 152 mm high floor assembly, load-oriented and torsion-resistant steel frame construction. Longitudinal beam floor construction with a load-resistant outer frame and with guide tunnel at 600 mm intervals, tunnel with guide at the top and sides, tunnel height approx. 45 mm, 4 x swap body corner fittings on 20ft base. 4 x support legs for Jumbo parking height 970 mm, extendable and foldable sideways by 90° with short safety strut and safety catch, bolt safety catch on the frame, stable drop latch as second transport safety catch, -symmetrical arrangement of support legs form A 2 for CWB C 745 / 782 for parking height of approx. 970 mm Reinforcement between the support legs 7 pairs of lashing eyes embedded in the outer frame, 2.5 tons each Heavy-duty pallet stop on both sides, approx. 20 - 25 mm high, with lashing option every 200 mm, loading height reduced by approx. 20 - 25 mm Door stop on the side Impact protection at the rear made of flat iron Djdpfx Afekt Ni Uemekw Floor Screen printing plates approx. 27 or 30 mm thick, manufacturer's choice, for high point load capacity, for forklift axle load up to max. 4400 kg Front wall/front stanchions 2,800 mm high, rest with tarpaulin, steel corner stanchions in volume design, release device for side tarpaulin on front wall Center stanchions 1 pair of sliding stanchions can be moved along the entire length, with 4 insertion pockets and a long pocket at the bottom. Insertion slats 3 rows of aluminum V-insertion slats or wooden insertion slats of the manufacturer's choice, 1 additional row/rows of aluminum V-slats Rear wall/rear stanchions Rear corner stanchions, steel up to lower edge of roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet Rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps Stainless steel tension locks Roof Sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-shaped roof rail for automotive industry, internal width between the roof rails approx. 2,490 mm, tarpaulin color: white EcoLift - lifting roof can be raised by approx. 380 mm, with gas pressure damper support, Approval / plates Country of approval: Germany Manufacturer's certificate in accordance with EN 12642 XL Paint finish Hot-dip galvanized frame Front corner stanchions hot-dip galvanized Front wall aluminum Rear corner stanchions Hot-dip galvanized Rear wall white Tarpaulin RAL 9005 jet black with advertising lettering Attention! These are archive pictures.

Condition: new, machine/vehicle number: 06b624786df9f4b5c196a36b0, empty load weight: 3 kg, maximum load weight: 11 kg, overall weight: 14 kg, axle configuration: 2 axles, tire size: 285 / 70 r 19,5, Further information Chassis central axle tipping trailer Welded steel construction, continuous tipping shaft at the rear with 80 mm ball tipping bearing 2-speed gearbox support foot at the front Folding rear support Wheel chocks with holder Dkedsi Ri Ipspfx Afmjw Steel underride guard Rear spray flaps across the entire width Quarter-shell mudguards Lockable storage space for access ramps underneath the loading area Towing device central axle trailer Drawbar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 285 / 70 R 19,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear Lights completely in LED version (note! with certain towing vehicles, misdiagnosis can occur, although the function is given) 1 x 15-pin plug at the front, with connecting cable, Hydraulics Three-way tipping mechanism, hydraulic multi-piston press with lift limiter and safety cable, Low-pressure cylinder up to max. 170 bar, without throttle. If necessary, this must be retrofitted to the truck. Hydraulic operation via truck power take-off Hydraulic connection with SVK plug NW 10/3, incl. connection hose Tilting bridges Sturdy tipper body with 4 mm sheet steel floor, steel side wall structure, continuous side walls, hinged and pivoting with central locking at the bottom. Rear corner stanchions pluggable. Rear wall can be folded down and pivoted, with central locking at the bottom. Platform length approx. 5,000 mm, side walls with 6 hinges at the bottom. Dropside retraction springs (not possible with split side walls) Rear wall hinged and as 2-leaf door (cannot be folded down), with door holder and protective rubber on the side Platform width 2420 mm 5 pairs of lashing eyes in the floor, 5 tons each Country of registration / plates Country of registration: Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paintwork Hot-dip galvanized frame incl. passivation15-year warranty against rusting through Dropside/bridge RAL 3002, carmine red Please note! Bridge only primed inside! Attention: Archive pictures!

Condition: new, machine/vehicle number: 2428b2018baf171e60fef6740, empty load weight: 8,900 kg, maximum load weight: 32,100 kg, overall weight: 41,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with interchangeable 2 kingpin and 2 kingpin positions, 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Mudguards in front of 1st axle and rear of each axle with anti-spray, according to EC Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 2 pairs of ring lashing eyes, 5 tons each at the front on gooseneck Djdsi Ri E Ropfx Afmokw 11 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 2 x on gooseneck 9 x distributed in the low loading area First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 8 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Wheels and tires 235 / 75 R 17.5 brand of the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, without connecting cable with lifting & lowering valve Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle - driving stability system Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1 LED rotating beacon with holder, switched via parking light (light can be removed) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Gooseneck with sheet steel covering Storage box recessed in drive-over slope to gooseneck Then with 70 mm softwood floor, steel/ checker plate covering in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 9 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK socket NW 10/3, without connecting hoses Operating instructions With 10,000 kg axle load, a special permit is required, only indivisible load possible!!! Special permit required if total train weight exceeds 40 tons! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) When applying for a special pe

Condition: new, machine/vehicle number: 15431365fe5515297a6a9fb05, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm Wooden planks 70 mm for widening to 3000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) Dedpfxji Ri A Ss Afmjkw 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: e763c8c2bb3370bd2342236a4, empty load weight: 3 kg, maximum load weight: 8 kg, overall weight: 11 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle tipping trailer Welded steel construction, continuous tipping shaft at the rear with 80 mm ball tipping bearing Gearbox support foot at the front 2 wheel chocks with holder Steel underride guard Lockable storage space for access ramps underneath the loading area Towing device central axle trailer Drawbar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension Euro axles of our choice, with angular roller bearings and S-cam brake Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Hand spindle parking brake Integral air reservoir without ABS, but with mechanical ALB, then max. 60 km/h approval 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, electrics 12 volt, multi-chamber lights, without amber LED lighting at the sides, reflectors at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 7-pin 12 volt plug at the front, with connecting cable, extended by approx. 60 cm Hydraulics Three-sided tipping mechanism, hydraulic multi-piston press with lift limiter and safety cable, Low-pressure cylinder up to max. 170 bar, without throttle. If necessary, this can be retrofitted to the truck. Hydraulic connection with SVK plug NW 10/3, incl. connection hose Hydraulic actuation via truck power take-off Tilting bridges Sturdy tipper body with 4 mm sheet steel floor, steel side wall structure, continuous side walls, hinged and pivoted with central locking at the bottom. Rear corner stanchions pluggable. Rear wall can be folded down and pivoted, with central locking at the bottom. Platform length approx. 4,500 mm, side walls with 5 hinges at the bottom. Platform width 2420 mm 5 pairs of lashing eyes in the floor, 5 tons each Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion, for max. 60 km/h approval, towing vehicle LoF, (max. 40 km/h possible in Switzerland) Prepared for single-line license plate holder without contour marking / reflective strips according to ECE R 048, Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Dropside/bridge RAL 3002 carmine red Please note! If the bridge is galvanized, it will not be painted! Note! Bridge only primed inside! Wide tires also possible for an extra charge. 355 / 60 R 18, then loading height approx. 980 mm Attention: Archive pictures! Dodpfxei Rizbo Afmokw

Condition: new, machine/vehicle number: ebf3f771e96394cd89e56bbb7, overall weight: 11,800 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle trailer Welded fine-grained steel construction 6 pairs of lashing eyes bolted to the outside of the floor/outer frame, 5 tons each 2 pairs of lashing eyes additionally bolted to the floor, 5 tons each in the corners Gear support foot at the front Folding rear support 2 wheel chocks with holder Steel underride guard Rear spray flaps across the entire width Quarter-shell mudguards 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Towing device central axle trailer Towing bar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension Drum brake axles, manufacturer's choice Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system Dksdsi Rixropfx Afmsw 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Floor Steel/ checker plate floor for high point load capacity Note: Slight floor corrugation possible due to welding distortion! Platform length approx. 5,200 mm Rear sloping to approx. 900 mm Front wall / front corner stanchions 25 mm aluminum hollow profile, 400 mm high, Drop sides 25 mm aluminum hollow profile, 400 mm high, foldable and removable Rear wall / rear corner stanchions 1 pair of steel stanchions attached to the frame and with bracket for locking the drive-on ramps, drive-in width approx. 2,430 mm Drive-on ramps 2 steel ramps 2,300 mm long, 510 mm wide, can be moved sidewayswith grab handle on the ramps covered with 3 toothed steel rails With gas pressure jack for one-man operation Country of registration/plates Country of registration: Germany 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Front wall aluminum Side wall anodized aluminium Drive-on ramps Hot-dip galvanized Attention! These are archive pictures.

Condition: new, machine/vehicle number: f044065451f6d849ee7a5b9f8, empty load weight: 5 kg, maximum load weight: 29 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 385 / 65 r 22,5, Further information Chassis semi-trailer forwarding Welded steel construction in reinforced design, only 2 side members as double T-beams with steel/checker plate between the side members, saddle plate with replaceable 2 kingpins. Protective plate for rear lights. 1 steel storage box, recessed between side members 8 pairs of lashing eyes bolted or welded to the frame at the manufacturer's choice 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EC 1 spare wheel holder for 1 e-wheel, with wheel fastening set 8 wooden stanchions of the manufacturer's choice, bolted to frame with 2 wooden stanchions each, telescopic from 1800 to 2800 mm, per pair 7 to. Axles + suspension SAF disk brake axles with 430 mm disk diameter Air suspension with lifting & lowering valve, safety cable on the axles 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle spacing offset mm (combined transport) up to 44 tons gross train weight Wheels and tires 385 / 65 R 22,5 at the manufacturer's discretion Steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installed (no calibrated scales) 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear Dodei Rivwepfx Afmjkw 2 x 7-pin and 1 x 15-pin interchangeable sockets at the front, without connecting cable Front bulkhead/front stanchions Steel/grid bulkhead, approx. 2,300 mm high, bolted to the frame Approval / plates Country of approval: Germany Approval according to EC 2007/46 Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Black coated support legs Front wall hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: eca976917d325d4adc41b69e8, empty load weight: 7,200 kg, maximum load weight: 27,800 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r 22,5, Further information Chassis semitrailer forwarding Fine-grained steel welded construction in lightweight design, fifth wheel plate with replaceable 2 king pins, main frame reinforcement for 25 tons in the centre of gravity on 3 m loading length when pushed together. 13 pairs of hooks for lashing strap attachment welded onto the cross members 23 pairs of lashing eyes embedded in the outer frame, 3.5 tons each Outer frame with Load-Lock profile for lashing strap attachment Please note! Cannot be used with drop sides! 24 t. 2-speed support winch in reinforced design for loaded trailer, single-sided operation, with semicircular lower section and straight connecting plate, with thrust compensation Wheel chocks with holder Aluminum side bumper Underride guard Half-shell mudguards with anti-spray flaps according to EG 1 spare wheel holder for 1 electric wheel, with wheel mounting kit 1 closed stanchion stowage box, open at the top, below loading area, doors on both sides, w=450 mm/H=400/420 mm/t=2460 mm 6 pairs of extendable stanchion pockets, for 80x80 mm tubular stanchions, extendable from loading width 2000 mm to 3100 mm 4 pairs of stanchion pockets embedded in the outer frame, for 80x80 mm shaped tubes 11 stake pockets centrally recessed in the floor, for 80x80 mm shaped tubes, with reinforcement beam, each installed between the outer stake pockets 5 x 3 pairs of stanchion pockets recessed on the outside of the longitudinal beams, for 80x80 mm shaped pipes, including reinforcement beams - for securing loads to the front and rear when transporting 2x5000 mm or 2x 6000 mm construction steel mats 6 lightweight stanchions W=80/ D=80/, usable height approx. 1850 mm, hot-dip galvanized, top with cable guide for belt tensioning 12 lightweight stanchions W=80/ D=80/, usable height approx. 1850 mm, hot-dip galvanized, with lashing eyes welded to the bottom on both sides Note: stanchion pockets / stanchions are not designed for securing long materials, pipes etc. on their own without looping around them 2 plastic toolboxes, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) 6 construction steel winches with wire rope and counter hooks, with rope feed-through through the outer frame, 1 removable slip-on gear for construction steel winches - supplied loose (without bracket on the frame) Telescoping Main frame can be telescoped Extendable by max. 4,000 mm and can be arranged approx. every 500 mm Locking with pneumatic bolt locking + display Frame locking on both sides, actuation via hand knob, operation for brake/locking and suspension in FR-left in front of the axles Storage compartment between the side members when extended Axles + suspension SAF disc brake axles with 430 mm disc diameter Last axle self-steering, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button, as well as manually via switch in the towing vehicle (pin 10), without truck installation. Offset axle spacing mm Air suspension 1st axle automatic lift axle, can also be operated electrically from the truck, with starting aid, without truck installation (starting aid is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake system Colored cable routing for easy servicing Spring-loaded parking brake Dkjdpfsi Ri Szox Afmow 2 swap-proof coupling heads at the front, without connecting line EBS make of the manufacturer's choice, electronic brake syst

Condition: new, machine/vehicle number: 535119ca408d3bd5a8e74be51, empty load weight: 6 kg, maximum load weight: 11 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support Wheel chocks with holder Aluminum side collision protection Half-shell mudguards on 1st axle, quarter-shell mudguards in front of and behind the 2nd axle with anti-spray flaps behind each axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm), storage compartment for wooden planks in the middle of the loading area, wooden planks 70 mm for widening to 3,000 mm, Low loader lashing eyes 3 pairs of lashing points each 10 tons integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x according to the rest of the neck area distributed between them, spacing not greater than 1200 mm, Dkjdpei Ri N Hsfx Afmsw 1 x rear slope 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (instead of stake pockets) Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white/red rear lane departure lights 2 white position lights at the front 1 rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Front area steel floor, then with 70 mm softwood floor, steel/ checker plate flooring in the wheel arch area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Additional ramp safety device hinged at the bottom (to prevent the ramps from slipping sideways, not in conjunction with hydraulic side ramp displacement) covered with wood with spring lift support Operating instructions A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give a commitment for 20 tons GG. Customer risk. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. Approval / plates Country of approval: Germany Test approval according to EG 2007/46 24/7 service hotline Prepared for two-line license plate holder Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paint finish Frame DB nova gray Drive-on ramps hot-dip galvanized Attentio