Low loader semitrailer

Vega VEGA, 3-Achser, Hydr. Rampen, Verzinkt, Gelenkt

Condition: new, axle configuration: 3 axles, loading space length: 10,636 mm, loading space width: 2,480 mm, loading space height: 2,300 mm, loading space volume: 60 m³, Chassis manufactured in self-supporting ALUMINIUM construction with corresponding reinforcements in the lower flange for particularly high stability and strength, aggregate chassis made of ALUMINIUM, 140 mm frame height! (max. 39t) Axles and Suspension “Disc Brakes 22.5” Jost axle assemblies 3 x 9 tonnes with DC air suspension, lifting and lowering, Wabco Smartboard, electronic brake pad wear indicator (BVA) for display in the tractor unit (without tractor equipment), 1st and 3rd axles separately liftable with start-up aid (without tractor equipment), 3rd axle also with Optiturn, ECAS air suspension, tire pressure monitoring Wabco Trailerpulse with ZF rim-mounted sensors Ffodjfakkcjpfx Aa Rot Tyres and Wheels 6 wheels with tyres 385/65 R 22.5 as per manufacturer selection, Alcoa aluminium rims DuraBright - 11.75x22.5 ET 120, kingpin bolted into a 10 mm thick plate Landing Gear Aluminium drop-leg landing gears, 2 x 10 t support load, for air suspension we use swivel feet Brake System According to E.G. standard, two-line braking system, EBS E-system Wabco with RSS system (Roll Stability Support), spring-loaded brake system acting on two axles with control at rear, aluminium air tank system, premium modulator Electrical System According to STVZO regulations with 2 LED five-chamber tail lights type Aspöck Europoint LED integrated in aluminium rear closure, 24 volt system with 1x 5-pin and 2x 7-pin sockets, side marker lamps in LED, 2 separate LED work lights at rear, 2 LED work lights at first landing gear height, 1 LED work light inside front left, operable from outside Body/Tipper Body "Body fully welded on the inside" Front wall load 17,250 dN, rear and side walls 10,250/13,400 dN. Aluminium body, side walls made of 30 mm thick ALU plank profiles (2-3 mm), 600 mm wide, fully welded with lower and upper flange, plank profiles fully welded on inside, floor as moving floor system laid on 140 mm ALU cross beams, floor load approx. 7 t/m², crossbeams closely spaced (approx. 350 mm), ALU front wall with 600 mm plank profile, 2-3 mm thick, in straight design, special ALU corner profiles in beveled version, flat rear wall in straight design with 2 ALU swing doors 50/30 mm, with 4 locking bars in welded ALU rear frame mounted in Teflon and stainless steel bearings, continuous reinforced ALU upper flange supporting ALU wall with "Kevlar tarpaulin for complete emptying, side brush seal, additional side Kevlar tarpaulin, integrated discharge chute with folding cover plate at rear left bottom, operable from outside, inspection window rear left, one sampling flap in each rear door (2 pcs.), service door front left Hydraulic System "Cargo Floor moving floor system in the floor with hydraulically operated ALU profiles mounted on ALU square profiles with approx. 670 PE-HD sliding plates, approx. 6 mm floor thickness, hydraulics with approx. 200 mm working stroke, fixed parts at front wall, separate option for connecting hydraulic line under the vehicle with fixed halves, line size NW 21, fixed halves with sizes and type to be specified, operating pressure 190 to max. 240 bar, ALU end pieces welded into floor, electric control rear left with cable control in a lockable waterproof box, Accessories PVC mudguards with rubber mud flaps, ALU spare wheel carrier, side ALU underrun protection in folding version, 1 tool box approx. 800x460x430 mm in plastic, approx. 3.7 m ALU ladder, rolling tarpaulin 680 g/m² quality with rolling tarpaulin system incl. sides.

Condition: new, Part suitable for: trucks Ffedpfxjuxahkj Aa Ret General condition: very good Technical condition: very good Optical condition: very good

Condition: new, empty load weight: 12,900 kg, maximum load weight: 34,100 kg, overall weight: 47,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,540 mm, loading space height: 350 mm, suspension: other, tire size: 245/70 R 17,5, color: grey, operation weight: 12,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered hydraulically and removed -Technical fifth wheel load: 23,000 kg -For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading area: -Low bed with external supports in extendable "SUPER LOW" design, length approx. 6,850 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking Rear chassis: -Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear -2 pairs of lashing rings that can be folded outwards -1 pair of lashing rings lying in the trough -2 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame Ffsdpfxohlz R So Aa Rot Pendulum axle and tires: -"PENDEL-AXLE", all axles hydromechanically forced steered -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint, painted in a single color in "FAY-Gray-34-0260" -Technical axle load: 12,000 kg -Hydraulic axle compensation -Tires 245/70 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories: -Preparation for screw-on container positioning for 1x 20ft or 1x40ft container on the outer supports -2" kingpins -A galvanized steel front wall approx. 400 mm high -One spare wheel -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Electro-hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and at the rear -European reflector signs (red-yellow) on the rear of the trailer -One holder for the warning signs including a socket on the gooseneck and on the rear panel on the left and right -6 pairs of threaded blocks between the lashing rings under the top strap on the outer support for mounting screwable RUD rings VLBG-4 -ALU side walls and rear wall can be plugged into the gooseneck approx. 2,440 x 400 mm -The rear galvanized plug-in stanchions are removable (Length of the body approx. 2,560 mm) -Gooseneck in the rear upper area closed with a removable cover -5 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Foldable extensions, approx. 230 mm per side -2 pairs of screwable RUD rings VLBG-4 M24 (LC 8,000 daN) -1 pair of steel ramps to bridge the hooks of the low bed -A painted layer of sand on the loading area as anti-slip protection -Speed sticker 80 km/h at the rear and on both sides -Dipper handle recess of the rear chassis closed at the rear with a plug-in plate -Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm -Radio remote control for the steering in addition to the cable remote control, with indicator lights on the receiver as Alignment control -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 normal grease -Load pressure gauge for determining axle loads -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: new, functionality: fully functional, machine/vehicle number: XPNK0C200PD101865, first registration: 08/2024, next inspection (TÜV): 08/2026, loading space volume: 77 m³, Year of construction: 2024, Technical data: - Saddle height: 1,250 mm / 1,350 mm - Outer length: 12,095 mm Ffodpfx Aoun Iuioa Rot - Volume: 77 m³* - Outer width: 2,550 mm - External height: 3,950 mm - Front overhang: 1,495 mm - Support leg spacing: 2,350 mm - Wheelbase: 6,875 mm - Rear overhang: 3,725 mm - Number of axles: 3 - Tire size (standard): 445/65 R 22.5 - Maximum permissible axle load: 10,000 kg - 1st axle: Lift axle - 3rd axle: self-steering axle - Brakes: Drum brakes *Volume depends on the selected options Basic equipment: General - Aluminum vehicle frame for low unladen weight and high payload - Aluminum support leg construction with aluminum drop support legs - All aluminum cross members in heavy-duty design; the short cross members on the axles are the axles are inserted with steel U-profiles - Aluminum side walls consisting of a 3 mm inner side and a 2 mm outer side - The side walls are continuously welded on the inside over the entire height (for maximum strength and minimum soiling) - Hydraulic tailgate with 115 degree opening angle, integrated lighting and Grain pusher and 115 degree opening angle - Operation via radio remote control - Body sanded, primed and painted in 2K paint - Two-year guarantee on paint and construction Attachment - The fifth wheel plate is built with a robust steel box construction for a maximum fifth wheel pressure of of 18,000 kg (12,000 kg approved / 18,000 kg technical) Loading space - Corrugated aluminum floor boards, 6 mm, 21 boards with aluminum and plastic end caps Wear strips Hydraulic floor drive with 3 cylinders that move 7 floor strips each; Equipped with pressure gauge and temperature protection - Automatically retracting moving partition wall, hydraulically operated by means of radio remote control Price on request Subject to prior sale and errors excepted Locations may vary Internal: S51573

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit Ffjdpfxotx Nwns Aa Rjt HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: new, empty load weight: 6,350 kg, maximum load weight: 38,650 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 13,600 mm, loading space width: 2,540 mm, suspension: air, tire size: 385/65 R22,5, Equipment: ABS, Loading area: -2 pairs of lashing rings can be folded outwards (LC 5,000 daN) 24 pairs of cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) Seat posts: -JOST fifth-wheel supports (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles, air-sprung, with disc brakes (430 mm), with lifting/lowering function -385/65 R 22.5 tires Brake system: -WABCO brake system in accordance with EU regulations with EBS-E (2S2M) Paint finish: -First-class and long-lasting corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in MB 7350 nova grey -Rear part metallized and painted in RAL 9010 (pure white) -No metallic paint finish possible Steel construction: -steel construction made of high-strength fine-grained steels -Steel qualities: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690Mpa) Electrical system: -Electrical system according to EU regulations -Lighting 24 Volt -ASPÖCK-NORDIK (ASS3) -ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets -Connection according to ISO. -24N ISO-1185 -24S ISO-3731 -15-pin ISO-12098 Accessories included: -Yellow-red air couplings on the galvanized connection strip at the front -4 pieces of restraining shoes with bracket -2" kingpin Ffsdpjiu Etkjfx Aa Rst -One galvanized steel end wall approx. 1,600 mm high. EN12642-XL -White reflector tape in accordance with EU regulations on the side of the trailer and red at the rear -European reflector plates (red/yellow) at the rear of the trailer -Loading area with approx. 30 mm thick hardwood floor edged in omega profiles -10 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -3 pairs of stanchion pocket rails, mounted transversely in the cargo bed, for 100 x 50 mm stanchions -Storage for 1,000 mm stanchions, at the rear in the central support -1 Spare wheel holder under the cargo bed on the right in the direction of travel -One mud flap at the rear of the trailer -Manual and description on USB stick -One bracket for a rotating beacon at the rear of the trailer -One bracket for the warning signs on the gooseneck and on the rear panel on the left and right, including socket -6 pairs of WADER container pockets in the loading area, for 1x 20ft container, 2x 20ft containers or 1x 40ft container. Flush with the rear -Speed stickers 80 km/h at the rear and on both sides -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with one LED position light -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: used, mileage: 226,000 km, power: 345 kW (469.07 HP), first registration: 05/2021, fuel type: diesel, overall weight: 18,000 kg, brakes: retarder, gearing type: automatic, emission class: euro6, Equipment: soot filter, - Retarder - Air conditioning - Power take-off - Full equipment Suspension: Air suspension Ffsdpfx Aajxxxnho Rjt

Condition: used, empty load weight: 9,480 kg, maximum load weight: 31,520 kg, first registration: 03/2020, next inspection (TÜV): 04/2024, total length: 11,500 mm, total width: 25,500 mm, total height: 38,000 mm, suspension: air, tire size: 245/70 R 17.5/10mm, wheelbase: 1,800 mm, front tire size: 245/70 R 17.5/10mm, operation weight: 41,000 kg,

Condition: used, empty load weight: 10,730 kg, maximum load weight: 38,770 kg, overall weight: 49,500 kg, axle configuration: 3 axles, first registration: 07/2024, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5 3PMSF, color: grey, Year of construction: 2024, Equipment: ABS, Gooseneck: -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Loading area in extendable version: -Loading surface in extendable version with rear slope of approx. 1,000 mm x 8° -6 pairs of lashing rings can be folded outwards -3 pairs of lashing rings can be folded outwards -1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: -A pair of galvanized, two-part steel ramps, approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable -Maximum load per pair: approx. 40,000 kg Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electro-magnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 3PMSF Ffodsvcpagopfx Aa Rot -TPMS tire pressure monitoring system Paint finish: -First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component zinc dust primer A high-quality 2-component top coat in one color in MB 7350 nova grey Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -One bracket for rotating beacon at the rear of the trailer -Mounting in the rear area of the gooseneck for ALU trailer lights -Galvanized folding supports under the bevel of the cargo bed -Cover plates to bridge the space between the ramps and the cargo bed -White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear -Electric hydraulic unit at the rear, under the cargo bed -On the gooseneck and on the ramps on the left and right a holder for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -ALU drop sides and rear wall can be plugged onto the gooseneck, approx. 2,440 x 400 mm -The rear, galvanized stanchions are removable Length of the body approx. 2,560 mm -Four warning signs, extendable by approx. 400 mm, approx. 423 x 423 mm with one position light -3 pairs of WADER container pockets in the loading area for a 20ft, 30ft or 40ft container -6 pairs of stake pockets approx. 100x50 mm in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -A layer of sand painted onto the chequer plates, above the kingpin and the cargo bed to prevent slipping -On the warning plates a holder for rotating beacon -European reflector plates (red/yellow) at the rear of the trailer -Speed stickers 80 km/h at the rear and on both sides -Load manometer to determine the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-peened, then the defined visible surfaces coated in Metallization with ZINACOR 850 (zinc 85% - aluminium 15%) hot-finished

Condition: new, maximum load weight: 25,645 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete stock of immediately and soon-to-be available vehicles on our website. Excerpt from equipment specification. Complete specification available on request. Load area: - Low-bed design with central beam, extendable version, approx. 6,750 mm in length - 5 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the loading platform (LC 10,000 daN) Gooseneck: - Hydraulic lifting/lowering gooseneck, detachable Rear chassis: Fodsxf Siljpfx Aa Roft - Short rear chassis with closed outer frame and checker plate covering - Chassis with excavator trough, closed in the rear half for housing the air tanks - 2 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Air suspension with raise/lower control valve Tyres: - Tyres 245/70 R 17.5, 3PMSF - TPMS: Tyre Pressure Monitoring System according to ECE R 141 Brake system: - Wabco braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality single-tone 2-component (2K) top coat in RAL 3000 Flame Red Including the following additional equipment: - 2 kingpins - Galvanised steel front wall, approx. 400 mm high - Remote steering from front and rear, operated by cable remote control with push buttons, including single tracking control for the axles (no installation in the tractor unit) - Electro-hydraulic unit - Axle load gauge including load diagram - On the gooseneck, removable aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). Rear galvanised stake pockets are removable. (Body length approx. 2,560 mm) - Separate air connection with air gun on the gooseneck - 2 work lights with switch on the trailer, mounted on the left and right of the gooseneck platform - 1 INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck - 6 pairs of stake pockets for insertable posts approx. 100 x 50 mm in the outer frame of the load area, 2 pairs in the chassis outer frame - Galvanised, extendable width extensions approx. 230 mm per side - Hydraulic connections from gooseneck to low bed with multi-coupling (instead of screw couplings). No seal guarantee included. - Central lubrication system with 2 BEKAMAX (Pico) pumps, standard NLGI-2 grease, with removable protection around the pump - 2 pairs of WADER container locks on the loading area, for 1x20' container - 1 removable galvanised intermediate table with 1 pair of WADER container locks - 1 pair of steel ramps for bridging the low bed’s hook mountings - Anti-slip sand-coated layer painted on the load area - HRM Metallisation (High Resistance Metallisation)