Used Low loader trailer / lowboy trailers for sale (618)

Condition: used, overall weight: 24,000 kg, axle configuration: > 3 axles, first registration: 04/2016, next inspection (TÜV): 11/2025, * SAF axles * Wheel recesses * 4th axles * Hydr. loading ramps * 50mm towing eye * Tare weight: 9,460 kg Duelraasvawaco E Ijt * Gross vehicle weight: 24,000 kg * TÜV: 11.2025 * SP: 05.2025 -----Internal vehicle number: 10091----Errors and omissions excepted.

Condition: new, overall weight: 40,000 kg, maximum load weight: 31,100 kg, axle configuration: > 3 axles, loading space length: 10,410 mm, loading space width: 2,500 mm, loading space height: 900 mm, total width: 2,520 mm, Total weight: 24,000kg/40,000kg Empty weight: 8,900kg Payload: 15,100kg/31,100kg Total length: 11,940mm Loading length: 10,410mm total, 2,490mm offset, 7,920mm loading bed including rear bevel Width: 2,520mm Loading height: 900mm Further information plus pre-freight / provision from storage location 26639 Wiesmoor 1,280.00 €/net Steel welded construction Turntable with strong ball bearing ring Foldable rear support Wheel chocks with holder Aluminum side impact protection Rear splash guards across the entire width (not in conjunction with forklift bracket) Half-shell mudguards 1st + 2nd axle with anti-spray splash guards behind each axle, Anti-spray flaps in front of and behind the 3rd and 4th axle Excavator arm recess above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons. in the excavator arm recess on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear bevel 1 plastic tool box, w=600 / h=425 / d=460 mm, lockable 1 storage box embedded in the floor on a crank with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm (not in the rear bevel) (The track width of the construction machines or vehicles to be transported must not exceed the outer frame width 2,550 mm) Storage compartment for wooden planks below the low-loading area Wooden planks 70 mm for widening to 3,000 mm Lashing eyes for low-loader 1 pair of lashing cutouts in the longitudinal beam at the front on a crank, 10 tons each. 4 pairs of lashing holes in the outer frame, each with 5 tons (tension belt attachment) 9 pairs of lashing mushrooms, embedded in the outer frame at the top and sides, each with 10 tons 2 x at the front on the bend 7 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the back, distance between the lashing eyes not greater than 1100 mm 3 additional pairs of folding lashing eyes, each with 10 tons 1 x on the bend (sticks out) 1 x at the beginning of the low bed, embedded inside on the longitudinal beams 1 x embedded in the floor behind the last axle Towbar with tested 50 mm towing eye Towbar height adjustment via spring Axles + suspension Drum brake axles, as selected by the manufacturer "Laser-measured axle/chassis" Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free Steel-rubber bearings and mechanical axle load compensation at the front and rear (rocker compensation) Wheels and tires 235 / 75 R 17.5" at the manufacturer's discretion Steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake 2 interchangeable coupling heads at the front, with connecting lines to the towing vehicle, 24 volt ABS and ALB, with ABS plug at the front, with connecting cable Caution: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrics 12-24 volts, multi-chamber LED lights, yellow LED lighting on the side, license plate lighting in LED, (Note! Incorrect diagnoses can occur with certain towing vehicles, although the function is present) 2 white position lights at the front in LED 2 white/red lane keeping lights at the rear in LED 2 x 7-pin, interchangeable plugs at the front, with connecting cable, Duolrsvyphloaa E Ijt 1 LED rotating beacon with holder, switched via parking light (light removable) 2 pairs of warning signs with double LED lighting and extendable

Condition: new, overall weight: 3,500 kg, maximum load weight: 2,813 kg, axle configuration: 2 axles, loading space length: 3,500 mm, loading space width: 1,600 mm, loading space height: 420 mm, !!! One-time SPECIAL PRICE !!! !! Only one unit in stock, no further discounts or rebates available !! Model Builder 3 Construction Equipment Transporter 3500 kg / 350 x 160 cm Internal box dimensions approx. 350 x 160 cm GVW 3500 kg, payload approx. 28 kg Loading ramp approx. 1600 mm long, ramp angle only approx. 17° Actual vehicle weight: XX kg Tires: 5 50 R C The Model Builder 3 is the ideal transporter for transporting various small excavators and other mobile machinery. Because the loading floor is located between the wheels, this trailer has a very low loading area (45 cm). In addition, the basic version is equipped with a solid folding support wheel, Temared's TÜV-certified load securing system with tie rings integrated into the side edges, a bucket rest on the front, a full-width steel ramp (160 cm high) with a gas spring, supports, playpen profiles, and robust locks. Of course, this Temared trailer also features a fully welded, fully galvanized chassis with a V-drawbar. NEW - Includes invoice with VAT, 2-year TÜV (braked)/3-year TÜV (unbraked) and a 2-year warranty. The vehicle documents can be sent in advance after a down payment or payment has been received so that you can register the trailer for pickup. Some images do not reflect the basic equipment. Subject to errors and changes. Pickup at our headquarters Engelhard Trailer Wholesale Market Steinauer Weg 15 91589 Aurach Dujlraa Eoi I E D Se Iet Tel: Fax: 9 Homepage: Upon request, the handover can also take place in 06618 Wethau, (Gmach Company) East Collection Warehouse near Leipzig, Tel., Fax for an additional charge of €150.00 (if in stock there!). The handover fee is payable directly on site. IMPORTANT! - If you would like to pick up the item in Wethau, please call in advance to check availability! Opening Hours: Monday - Friday 8:00 a.m. - 12:00 p.m. and 12:00 a.m. - 5:00 p.m. Saturday 9:00 a.m. - 12:00 p.m. Outside of these hours, you can also send your inquiries at any time by fax to 9.

Condition: used, overall weight: 12,000 kg, maximum load weight: 7,400 kg, axle configuration: 1 axle, loading space length: 4,500 mm, loading space width: 2,460 mm, loading space height: 1,300 mm, first registration: 05/1969, Year of construction: 1969, total width: 2,460 mm, total height: 1,300 mm, Tang Hilden * Low loader * 1 axle * tiltable * EZ: 05/17/1963 * Gross vehicle weight approx. 12000 kg * Own weight approx. 4600 kg * Payload approx. 7400 kg * Overall dimensions: 10000 x 2460 x 1300 mm * Loading dimensions: 4500 x 2460 mm The vehicle has signs of use and wear commensurate with its age! !! ATTENTION - MUST READ !!! We expressly reserve the right to sell the vehicle prior to sale, as we are also offering this item on other portals. We strongly recommend an inspection and test so that the buyer does not have any false ideas about the condition and suitability. Inspections and tests are possible at any time by appointment and are expressly desired !!! The internal dimensions given are approximate. TRADE-IN POSSIBLE FOR ALMOST EVERYTHING!!! EXCHANGES AND PAYMENTS POSSIBLE!!! Exhibition site: 58285 Gevelsberg, Am Sinnerhoop 17 Opening times: Monday - Friday 8.30 a.m. to 5 p.m., Saturday 8.30 a.m. to 2 p.m. Over 500 new and used trailers always in stock!!! Pegasus Anhänger GmbH Am Sinnerhoop 17 Djleu Azwhjraa E Isut 58285 Gevelsberg Tel.: Fax:

Condition: used, overall weight: 24,000 kg, empty load weight: 8,400 kg, maximum load weight: 15,600 kg, loading space length: 10,000 mm, loading space width: 2,500 mm, first registration: 08/1993, next inspection (TÜV): 10/2022, suspension: air, tire size: 9.5R 17.5, color: other, gearing type: other, front tire size: 9.5R 17.5, rear tire size: 9.5R 17.5, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Registration service, HU/SP/UVV, transfer to the port Djlraa Esk Auxio Iout Languages: German, Russian, English, Arabic     Very long LOADING AREA. 10.00 m ! Hydraulic ramps Ready for use Expandable     Gray-black Extras in the equipment ABS, turntable, air brake, EBS, air suspension, price on request (mobile), suspension: air, payload (kg): 15600 Build type: expandable, top condition, 10.00 m loading area, HSN/TSN: 6631/000   Errors excepted.

Condition: new, overall weight: 14,400 kg, maximum load weight: 10,500 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 ton. Gigant axles * Air suspension with lifting and lowering system * Drawbar height adjustable by 300 mm * Drawbar extension by 250 mm to 2,250 mm * Tire pressure monitoring with display option in the truck via EBS signal - without truck-side installation * 15-pin power plug * LED lighting * Support winch at the front * External folding supports at the rear * Plastic tool box approx. 858 x 500 x 500 mm at the front right outside on the bulkhead * Side impact protection * Plastic quarter fender * 50 mm softwood floor * Device in front of the bulkhead and at the rear for subsequent installation of 20" cont. locks * Screwed bulkhead made of smooth sheet metal * Side walls made of sheet steel - trapezoidal profile - foldable, split 1x in the middle * Steel rear wall can be inserted between the ramps. Holder when not in use inside in front of the Front wall * Rear stanchions screwed * Perforated outer frame bent at approx. 45 degrees with 2 ton lashing force every 480 mm * Installation of 3 ton lashing brackets every 600 mm possible - 4 lashing rings installed on each side - * 1 x 6.3 ton lashing ring in each of the front and rear corners * Various holes in the front and end beams for 1.2 ton lashing option * One-piece mechanical Grating loading ramps with spring mechanism for one-man operation approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Rear approach slope approx. 860 mm Duelrasl Thvxea E Iet * Chassis, drawbar, bulkhead, tailgate, folding supports and loading ramps hot-dip galvanized * Axles, springs, air tank, flange drawbar eye and support winch painted in a black tone * Painting of the side walls Color freely selectable up to approx. 2 weeks before the production date, but no metallic or special colors * --reinforced and certified structure according to EN 12642 XL including load securing certificate-- * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf on the A7 * Available week 23/2025 * Sample images

Condition: used, overall weight: 3,500 kg, maximum load weight: 2,680 kg, axle configuration: 2 axles, loading space length: 3,750 mm, loading space width: 1,850 mm, loading space height: 270 mm, first registration: 04/2022, next inspection (TÜV): 04/2026, Year of construction: 2022, total width: 2,453 mm, total height: 2,020 mm, Humbaur HS 353718 * Construction machinery transport trailer * Transport trailer * Aluminum floor * 100 km/h approval * Year of manufacture: 2022 * EZ: 05.04.2022 * HU: 05-2026 * Weight: 820kg * Total weight: 3500kg * Payload: 2680kg * Overall dimensions: 5730mm x 2453mm x 2020mm * Internal dimensions: 3750mm x 1850mm x 270mm * Tires: 14 inches * Welded side wall/frame construction * Bolted V-drawbar, hot-dip galvanized * 13-pin plug and reversing light * Hot-dip galvanized steel ramps * Ramp 1500 with anti-slip Grid covering and integrated support feet * Lashing rings mounted in the outer frame 12 pieces (6 pairs), tensile force 1000 kg per lashing ring * Fully automatic support wheel * Walkable steel fenders that close with the side walls The VAT is deductible. ATTENTION !!!!! MUST READ !!!!! We expressly reserve the right to sell the item prior to delivery, as we also offer this item on other portals. We strongly recommend a viewing and inspection so that the buyer does not have any false ideas about the condition and suitability. Viewings and inspections are possible at any time by appointment and are expressly desired !!! Images are similar, may contain accessories for which an additional charge is required. The internal dimensions given are approximate. For new vehicles, additional costs for vehicle documents and freight may apply. TRADE-IN POSSIBLE FOR ALMOST EVERYTHING !!! EXCHANGES AND PAYMENTS POSSIBLE !!! Exhibition grounds: 58285 Gevelsberg, Am Sinnerhoop 17 Duolrsvm R S Soaa E Ijt Opening times: Monday - Friday 8:30 a.m. to 5:00 p.m., Saturday 8:30 a.m. to 2:00 p.m. Always over 500 new and used trailers in stock!!! Pegasus Anhänger GmbH Am Sinnerhoop 17 58285 Gevelsberg Tel.: Fax:

Condition: used, overall weight: 24,000 kg, empty load weight: 5,500 kg, maximum load weight: 18,500 kg, loading space volume: 11 m³, loading space length: 7,200 mm, loading space width: 2,550 mm, loading space height: 600 mm, first registration: 10/1999, next inspection (TÜV): 08/2022, suspension: air, tire size: 235/75R17,5 141/140J, color: red, gearing type: other, front tire size: 235/75R17,5 141/140J, rear tire size: 235/75R17,5 141/140J, driver cabin: other, emission class: none, Equipment: ABS, Registration service, HU/SP/UVV, transfer to the port Languages: German, Russian, English, Arabic   Dujlrasq Huq Asa E Ist   Basic color: red Extras in the equipment ABS, turntable, air suspension, suspension: air, payload (kg): 18500 Body type: 3-axle low-loader trailer with side walls, can be widened. Needs a bit of work, but the substance is good, HSN/TSN: 6631/000   Errors excepted.

Condition: new, overall weight: 27,000 kg, maximum load weight: 20,200 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, Year of construction: 2024, * ETÜ-TR 27.0 Plateau: * EBS (electric braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 9 ton. BPW Eco axles * Air suspension with lifting and lowering system with RTR function * 1st axle can be lifted * Last axle as trailing steering axle with electro-pneumatic steering lock through PIN reverse gear (locking of the trailing axle from the chassis for maneuvering purposes - without installation on the truck side - assigned to PIN 10 in the 15-pin plug connection only for maneuvering purposes, not on public roads * SmartBoard control box as an information tool with pressure sensors for total axle load display * Tire pressure monitoring with display option in the truck via EBS signal without installation on the truck side * Fixed center drawbar with 50 mm flange drawbar eyelet (loaded 900 mm, mm height adjustment on head plate) * Mechanical support winch at the front, mechanical swivel supports at the rear of the chassis * Mechanically adjustable warning sign package at the front and rear * Tool boxes made of galvanized sheet steel - black powder-coated - approx. 650 x 300 x 600 mm on the right side * 15-pin power plug * LED tail lights * LED rotating beacon (removable) including holder and installation * 2 x LED reversing lights on the rear of the vehicle (switched via reverse gear) * Flashing LED side marker lights * 60 mm larch/Douglas fir floor * 400 mm steel bulkhead plugged in * Perforated outer frame bent at approx. 45 degrees with device for mounting 3 tonne drop lashing brackets * 1 x 10 tonne lashing ring in each corner and 2 x 10 tonne and 3 x 6.3 tonne lashing rings on each side * Various holes in the front and end beams for 1.2 tonne lashing option * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm, mechanically adjustable laterally * 4 hydraulic. Control block for possible retrofitting of hydraulic ramp shifting * Chassis, drawbar, bulkhead, mechanical rear supports, loading ramps hot-dip galvanized * Axles, air tank, flange drawbar eyelet and support winch at the front painted in a black tone * --Preparation for possible retrofitting of side walls-- * New vehicle with manufacturer's warranty Duelrasr Dpz Aoa E Ist * Errors and prior sale without reservation * Available immediately from Egestorf

Condition: new, overall weight: 40,000 kg, maximum load weight: 31,630 kg, axle configuration: > 3 axles, loading space length: 9,250 mm, loading space width: 2,520 mm, Equipment: ABS, * T 4: * EBS * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 to. Gigant axles * Parabolic springs * Mechanical axle compensation front and rear * Tire pressure monitoring with display option in the truck via EBS signal - without truck-side installation * Warning sign packages front & rear * Reflective side and rear contour tape * EBS multi-voltage system for 12 & 24 V electrics * LED rotating beacon (removable) rear * 24 V - 15-pin and additional 12 V -7+4-pin power cable * Extended connecting cables for agricultural and forestry tractors * LED lighting * Straight pulling shears with 40 mm pulling eye and stepless height adjustment * Powder-coated sheet steel toolbox and spare wheel holder in basket design on the right-hand side * Plastic single mudguards at the front * Straight steel mudguards at the rear, each with splash guard (spray mist suppression) * Side collision protection * Extended offset offset by 500 mm to the front * Stem of the bogie platform extended by 520 mm with 45° corners and 3 recessed storage compartments incl. lid and lockable * Chassis made of high-strength fine-grained steel * Floor above bogie platform made of 50 mm and in deep loading platform made of 60 mm softwood * Outer planks of the drive-on ramps made of 50 mm bamboo wood * 4 stanchion pockets on each side (but no stanchions available) with simultaneous 2 to. lashing option Dujlrol Th Evoaa E Ist * Lasi package consisting of: 2 lashing ropes 6.4 tons at the front left and right on the main frame of the turntable platform, 1 pair of 13.4 tons lashing rings at the front and rear sides. Lashing rings on the outer frame as well as 4 pairs of lashing rings 10 to. each on the sides, swivelling and lowerable, loadable in all directions and embedded in the outer frame, 2 pairs of lashing rings 6.4 to. on the side in the excavator stick support, 8 pairs of galvanized folding booms for 3 m total width (but not in the rear slope) * Widening planks stored on the left side in a storage compartment * Excavator stick storage above the rear axle up to the end of the approach slope approx. 2,300 x 740 x 190 mm * Mechanical rear drop supports * Hydr. hot-dip galvanized drive-on ramps approx. 3,000 x 720 mm * Hydr. lateral ramp displacement on sliding tube from the ramp shaft * Loading area above the turntable: approx. 2,990 x 2,520 mm, * Rear loading area: approx. 6,280 x 2,520 mm * Load height loaded approx. 860 mm (incl. 860 mm approach slope) * Chassis, bogie, access ramps, mechanical folding supports rear hot-dip galvanized * Axles, springs, air reservoir and turntable painted black * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available immediately from Egestorf

Condition: new, overall weight: 21,000 kg, maximum load weight: 16,000 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,420 mm, loading space height: 700 mm, Year of construction: 2024, * KA-TA-RT 21.0 ML: * Without ABS / EBS with 40 km/h approval * Spring-loaded parking brake, drum brakes * Gigant axles * Tandem balancing unit with 100 mm wide parabolic springs * Support winch at the front Duelraer Dpz Hsa E Ijt * mech. Fall supports at the rear * firmly welded drawbar with low-maintenance cap for K80 ball head coupling (can be adjusted by + 77 mm / 33 mm via head plate) with raised boom for the connecting cables * 12 V 7 + 4-pin power cable * LED lighting system 12 / 24 V with protective grille * 2 LED work lights at the rear, switchable from the towing vehicle without installation on the towing vehicle side * Side marker lights with indicator control * Plastic quarter fender * Plastic tool box approx. 750 x 350 x 300 mm on the right side * Chassis made of fine-grain steel * Steel pallet 3-way tipping structure with M-Strong side walls (front wall fixed, continuous side walls - without center stanchions - swinging via manual central locking and mechanically foldable with side wall spring lifter * hydraulic rear wall 500 mm high as hydr. chute and a 115° opening angle * 4 mm Hardox 450 steel floor * 1 x 7 tonne lashing eyes in each corner and 4 x 3 tonne lashing eyes on each side - recessed and foldable * Hot-dip galvanised two-step ladder in front of the front wall in FR left) * 1 pair of aluminium landing ramps (10 tonne / pair with axle distance over 2,500 mm) 3,570 x 410 x 120 mm suitable for rubber-tired and tracked vehicles * 2 mounting slots for aluminum docking ramps embedded in the chassis from the rear Load securing in accordance with EN 12642 XL * --Coupling height loaded approx. 530 mm * unloaded approx. 590 mm-- * Body paint in RAL 9010 pure white * Chassis, drawbar, rear drop supports, underrun protection hot-dip galvanized * Axles, air tank, support winch at the front * K80 coupling painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: new, overall weight: 18,000 kg, maximum load weight: 13,700 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,480 mm, Year of construction: 2024, * TRA 18.0: * 2 in 1 = for roll-off containers and as a low loader * RDÜ (tire pressure monitoring) * EBS electronic brake system Duolrjl Tq Nmsaa E Iot * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 10 anthracite axles * Air suspension with manual lowering at the rear * Pull scissors 2,000 mm long with 40 mm drawbar and height adjustment device * Toolbox made of powder-coated sheet steel approx. 1,000 x 300 x 600 mm and spare wheel holder in basket design on the right side * Reflective contour band on the side and rear * Side impact protection * Plastic quarter fender with splash guard * Plastic impact protection buffer at the rear * Foldable A-sign at the rear * LED tail lights * 15-pin power plug * Main frame with raised outer frame for guiding the roll containers * Sheet steel floor with roller recesses in the bogie area * Cont. length of 5,500 - 7,000 mm possible * pneumatic 4-fold clamp locking and mechanical plug-in stop angle at the front of the track, load securing certificate according to DIN 30722 - 1 * Lasi package consisting of: 1 pair of 10 ton UVV lashing rings at the front of the bulkhead support and 3 pairs of 10 ton UVV lashing rings on the side in the outer frame, 4 x 2 ton lashing eyes in cloverleaf design and 4 x 8 ton lashing brackets embedded in the outer frame * Weld bead as anti-slip coating in the track area of the ramp * mechanical Rear drop supports * 1 pair of aluminum landing ramps (10.6 tons / pair) 2,800 x 470 mm suitable for rubber-tired and tracked vehicles (lockable storage compartment from the rear) * Chassis, bogie, locking parts, rear drop supports hot-dip galvanized * but the pull scissors, axles, air tank painted in a black tone * New vehicle without first registration with full manufacturer's warranty * Errors and prior sale subject to reservation * Available immediately from Egestorf on the A7

Condition: new, overall weight: 19,000 kg, maximum load weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 19.0: * WabcoEBS- E (electronic braking system) * RDÜ tire control monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 11 to. Gigant axles * Air suspension with lifting and lowering system * Drawbar with 50 mm flange drawbar eyelet and height adjustment by 110 mm using offset plate * Jost support winch at the front * External folding supports at the rear * Plastic tool box approx. 750 x 350 x 300 mm on the right side * Side impact protection * Plastic quarter fender * 15-pin power plug * Multi-chamber tail lights * Reinforcement package for drilling equipment transport on the chassis * 50 mm softwood floor in clamped design Dujlromi Tcqsaa E Ist * Device in front of the bulkhead for subsequent installation of cont. locks * Screwed bulkhead made of smooth sheet metal * Divided side walls made of sheet steel - trapezoidal profile - foldable with folding stanchion in the middle * Steel rear wall can be inserted between the ramps - holder when not in use inside in front of the bulkhead * Rear stanchions screwed * Perforated outer frame approx. 45 degree bent with 2 ton lashing force every 480 mm * Installation of 3 ton lashing brackets every 600 mm possible * Lasi package: in the front and rear corners 1 x 10 ton UVV lashing ring, on the sides 2 x 8 ton UVV lashing rings retractable in the outer frame, various holes for 1.2 ton in the front and end beams. Lashing option * one-piece slide-in ramps approx. 2,750 x 620 mm * Rear approach slope approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, folding supports and ramps hot-dip galvanized * ---Axles, air tank, flange drawbar eye and support winch painted in a black tone--- * Loading height unloaded approx. 940 mm * Loading height loaded approx. 910 mm * Wheelbase: 1,810 mm * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available from week 22/2025 from Egestorf

Condition: new, overall weight: 21,000 kg, maximum load weight: 16,750 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 21.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 11 to. Gigant axles * Air suspension with lifting and lowering system * In front of the bulkhead and rear slope, device for subsequent installation of container locks for transporting 20" containers * Drawbar with 50 mm flange drawbar eyelet and height-adjustable drawbar * Jost support winch at the front * External folding supports at the rear * Plastic tool box approx. 750 x 350 x 300 mm on the right side * Side impact protection * Plastic quarter fender * 15-pin power plug * LED lights * 21 tonne GG version with reinforced frame and reinforced axles * Reinforcement package for drilling equipment transport on the chassis * 50 mm softwood floor in clamped version Djljq Dyu Ujraa E Ieut * In front of the bulkhead, device for subsequent installation of container locks * Screwed bulkhead made of smooth sheet metal * Divided side walls made of sheet steel -trapezoidal profile- foldable with folding stanchion in the middle * steel rear wall can be inserted between the ramps - holder when not in use inside in front of the front wall * rear stanchions screwed * perforated outer frame bent at approx. 45 degrees with 2 ton lashing force every 480 mm * installation of 3 ton lashing brackets every 600 mm possible * 1 x 10 ton lashing ring in the front and rear corners * Lasi package with 2 x 8 ton lashing rings on each side, retractable in the outer frame, various holes in the front and end beams for 1.2 ton lashing option * one-piece mechanical Grating loading ramps with spring mechanism for one-man operation approx. 3,000 x 620 mm (can be pushed together to 20 mm) * Rear approach slope approx. 860 mm chassis * Drawbar, bulkhead, tailgate, folding supports and loading ramps hot-dip galvanized * Axles, springs, air tank and support winch painted in a black tone * Loading height unloaded approx. 940 mm * loaded approx. 910 mm * Wheelbase: 1,810 mm * Tires: 235/75R17.5 * Painting of the side walls Color freely selectable up to approx. 2 weeks before production date, but no metallic or special colors * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available from week 20/2025

Condition: new, overall weight: 30,000 kg, maximum load weight: 23,500 kg, axle configuration: 3 axles, Year of construction: 2024, Equipment: ABS, * T 3: * ABS braking system * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles * Parabolic springs * Mechanical axle compensation at the rear * Lateral impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle closed plastic mudguards and rear axle straight galvanized. Sheet steel aprons each with splash guard * Reflective contour tape on the side and rear * Hinged lid (hot-dip galvanized) for the toolbox in the bogie platform * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm - black powder-coated - on the side under the chassis * 15-pin power plug * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * 4 stake pockets on each side (but no stakes available) with simultaneous lashing option * La-Si package consisting of: 2 lashing eyes (6.4 tons) at the front left & right on the main frame of the bogie platform * 5 pairs of UVV lashing rings that can be swiveled and lowered * Can be loaded in all directions and embedded in the outer frame in the corners 13.4 tons. otherwise 10 tons Delraotplwfsa E Ieut * 6 pairs of mechanical folding booms for 3 mtr. total width (but not in the rear slope) * Widening planks stored in a storage compartment under the loading area * Excavator boom storage above rear axle to the end beam approx. 2,100 mm long (2 pairs of 6.4 ton lashing rings on the side in the excavator boom storage) * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable tip section and load holding valves, hydraulic lateral ramp shifting * Hydraulic. Flow divider in the trailer (with hydraulic pump output in the truck of over 40 liters to max. 140 liters / min.), two-line hydraulics * Loading area above the turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm, (incl. 860 mm approach slope) * Loading height when loaded approx. 860 mm +/- 30 mm compensation unit * Chassis, bogie, folding boom, rear drop supports and loading ramps hot-dip galvanized. * Axles, springs, pull scissors, air tank etc. painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available immediately from Egestorf

Condition: new, overall weight: 40,000 kg, maximum load weight: 30,500 kg, axle configuration: > 3 axles, Year of construction: 2023, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 tonne Gigant axles * Air suspension with manual lowering at the rear * Pressure gauge for determining the load weight (axles separated into 2 air suspension circuits) * Warning sign packages at the front & rear * Reflective contour tape on the sides and at the rear, * Rotating beacon (removable) at the rear * 15-pin power plug * LED tail lights * Straight tow bar with 50 mm tow eye and infinitely variable height adjustment * Closed at the front. Plastic individual mudguards * Straight steel mudguards at the rear, each with splash guard (spray suppression * Side impact protection * Front section in front of the bogie platform by approx. 520 mm with 45° corners and 3 storage compartments including lockable hinged lids (hinged lid opens to the rear) * Chassis made of high-strength fine-grain steel * Floor above the bogie platform made of 50 mm and in the low-loading platform made of 60 mm softwood * Outer planks of the loading ramps made of 50 mm hardwood * Lasi package consisting of: 2 lashing rings 6.4 tonnes at the front left and right on the main frame of the bogie platform, 1 pair of 13.4 tonnes lashing rings on the outside frame at the front and rear, and 1 pair of 10 tonnes lashing rings on the side, can be swivelled and lowered, can be loaded in all directions and embedded in the outside frame, 5 bolted to the outside frame of the wheel wells ton lashing rings (2 on the front wheel well and 1 on the rear), 2 pairs of 6.4 ton lashing rings on the side in the excavator arm holder * 11 pairs of folding booms for 3 mtr. Total width (but not in the rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for the widening planks made of sheet steel, mounted across the loading area in front of the 1st rear axle * Excavator boom storage above the rear axle to the end of the approach slope approx. 2,300 x 740 x 190 mm * 2 wheel recesses on each side, approx. 640 mm wide - front 340 mm deep, rear 220 mm deep - with retractable cover (storage for the covers at the front on the bogie platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm * mechanical support legs at the rear * hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm * hydraulic. lateral ramp shift * Loading area above the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loading height when loaded approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, bogie, folding boom, rear support legs and ramps hot-dip galvanized * Axles, air tank and pull scissors painted in a black tone * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation, Duolel Tnv Ieraa E Ijt * Available for immediate delivery from Egestorf

Condition: new, overall weight: 50,000 kg, maximum load weight: 38,900 kg, axle configuration: > 3 axles, Year of construction: 2025, * T5 profile 50.0: * Wabco EBS (electronic braking system) * RDÜ (tire pressure monitoring) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 to. Gigant axles * last axle with trailing steering (the trailing axle can be locked from the driver's cab for maneuvering purposes without installation on the truck, and additionally using a switch on the trailer) the lock must be switched off before driving on public roads * air suspension, lifting and lowering system with RtR valve * 3rd axle can be lifted (with lifted axle, driving height + 30 mm) * forced unloading and forced lowering of the lift axle for maneuvering purposes (installation on the truck side required) with speed-dependent switching via the EBS electronics * Smartboard as an information tool with pressure sensors to display the total axle load for each axle group * tire pressure monitoring with display option in the truck via EBS signal (without installation on the truck side) * mechanical warning sign package for 3 m total width * 1,500 mm long towing scissors with 50 mm towing eyelet and man. Height adjustment * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm on the left side * Plastic mudguard VA and galvanized sheet steel mudguards HA * Front of the bogie platform with 45° corners and 3 storage compartments with lockable hinged lids (hinged lid opens to the rear) * Shortening of the low-loading platform by 500 mm to 6,280 mm including extended offset by 500 mm to the front * LaSi package: 2 x 6.4 ton lashing eyes at the front in the corners, 2 x 13.4 ton UVV lashing rings on the sides in the corners at the front and rear and 5 x 10 ton lashing rings on the sides. UVV lashing rings (can be swivelled and lowered and can be loaded in all directions), 4 stake pockets on each side with a simultaneous 2 ton lashing option, 1 x 16 ton UVV lashing ring on the rear cross member Duslraa Esl Tihuo Iot * Rubber covering on the folding frame, approach slope and on the running surface of the low-loader platform * Bamboo wood between the longitudinal beams in front of the excavator support shelf * Extendable and foldable extension boom for 3 m total width (plank holder under the chassis on the right side) * Excavator boom support with reinforcement profile from the last axle to the end support approx. L = 2,350 x W = 770 x D = 270 mm, 2 pairs of 6.4 ton UVV lashing rings on the side in the excavator boom support * hydr. Folding ramp with dual-line hydraulics and extendable tip section approx. 4,650 x 720 mm including load holding valves and hydraulic side shift * hydraulic rear support * hydraulic flow divider (with hydraulic pump output in the truck of over 40 ltr./min. up to max. 140 ltr./min.), * Loading height when loaded 890 mm +/- 20 mm due to the air suspension * Loading area above the turntable: 2,600 + 390 x 2,520 mm * Low bed loading area: 6,280 + 500 x 2,520 mm, including 860 mm approach slope * Chassis, bogie, drawbar, widening brackets, loading ramps hot-dip galvanized * Drawbar, axles, hydraulic. Axle supports and air tank painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available immediately from week 25/2025 * Sample images

Condition: new, overall weight: 14,400 kg, maximum load weight: 10,950 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2024, * ETÜ-TA-ER 14.4 Plateau: * RDÜ (tire pressure monitoring) Djlrajq Dyvnoa E Iout * EBS (electronic braking system), * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 ton BPW axles * Air suspension with lifting and lowering system * mechanically adjustable 3 mtr. Warning sign packages at the front and rear * Drawbar height adjustable by 300 mm with 40 mm flange drawbar eye * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (thus B dimension of approx. 8,080 mm) * Support winch at the front * External folding supports at the rear * Plastic tool boxes approx. 750 x 350 x 300 mm on the left and right sides * Side impact protection * Underrun protection * Plastic quarter fender * 15-pin power plug * LED lighting system 12 / 24 V * 2 additional LED reversing lights. at the rear (switched via reverse gear) * 1 LED rotating beacon (removable incl. holder) at the rear * 50 mm softwood floor * 2 pairs of container locks (extendable to 3 mtr. Cont. external width) and lockable * Locking dimension pushed in according to ISO - DIN 15190 = 2,259 mm. Cont. locks pulled out = 2,819 mm (this dimension is not according to DIN) with an absolute external width of 3,000 mm * Perforated external frame bent at approx. 45 degrees with 2 ton. lashing force every 480 mm, installation of 3 ton. drop lashing brackets every 600 mm possible - 5 x 3 ton. UVV lashing brackets installed on the sides -, 1 x 6.3 ton in the corners at the front and rear. Lashing ring (at the front directly behind the cont. locks in the wooden floor and at the back in the end beam) in the front and end beam various holes for 1.2 ton lashing option * 1 pair of aluminum slide-in ramps approx. 3,570 x 410 mm (load capacity 10 ton / pair) suitable for rubber-tired and tracked vehicles * storage compartment below the loading area in the chassis from the rear * ---Chassis, drawbar, front wall, underrun protection and rear supports hot-dip galvanized--- * Axles, air tank, front support winch and flange drawbar eye painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available immediately from Egestorf on the A7

Condition: new, overall weight: 11,900 kg, maximum load weight: 9,300 kg, axle configuration: 2 axles, loading space length: 6,000 mm, loading space width: 2,010 mm, loading space height: 325 mm, Year of construction: 2024, * ETS-TA-B 11.9: * EBS (electronic braking system) * RDÜ (tire pressure monitoring) * Drum brakes, 2 x 5.5 tonne Gigant axles * Parabolic springs with compensation unit * Drawbar height adjustable by 300 mm * Jost support winch * Mechanical fall supports at the rear * Plastic toolbox at the front right on the bulkhead * Side impact protection * LED lighting * 50 mm softwood floor * 1 x 6.3 tonne lashing ring in the corners in front of the bulkhead and the end support and 2 6.3 tonne UVV lashing rings on the sides embedded in the outer frame * One-piece mechanical Grating ramps with spring mechanism for one-man operation approx. 2,350 x 870 mm (internal distance 20 mm, ramps cannot be moved) * Front wall, side walls, fender and drawbar hot-dip galvanized * Axles, springs, air tank, support winch at the front painted in a black tone * New vehicle with full manufacturer's warranty * Errors and prior sale subject to reservation * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire control monitoring system * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 to. Gigant axles * Air suspension with lifting and lowering system and RtR valve * Smart board for determining load weight * Warning sign packages at the front and rear * Reflective contour tape on the side and at the rear * Rotating beacon (removable) at the rear Dolraasl Th Ape E Ijut * LED light * Straight pull scissors with 50 mm towing eyelet and stepless height adjustment * Tool box made of powder-coated sheet steel and spare wheel holder in basket design on the right side * Closed at the front. Plastic individual fenders * Straight steel mudguards at the rear, each with splash guard (spray mist suppression) * Side impact protection * Front of the bogie platform extended by 520 mm with 45° corners and 3 recessed storage compartments including lid and lockable * Chassis made of high-strength fine-grain steel * Floor above the bogie platform made of 50 mm and in the low-loading platform made of 60 mm softwood * Outer planks of the loading ramps made of hardwood, * 4 stake pockets on each side (but no stakes available) with simultaneous 2 ton lashing option * Lasi package consisting of: 2 lashing eyes 6.4 ton. at the front left and right on the main frame of the bogie platform * 2 pairs of 13.4 ton lashing rings on the outer frame at the front and rear and 4 pairs of 10 ton lashing rings on each side. can be swivelled and lowered * can be loaded in all directions and embedded in the outer frame * 2 pairs of 6.4 ton lashing rings on the side in the excavator boom storage * 8 pairs of galvanised folding booms for 3 m total width (but not in the rear slope) * Widening planks stored in a storage compartment on the left side * Excavator boom storage above the rear axle to the end of the approach slope approx. 2,100 x 740 x 190 mm * mechanical fall supports at the rear * hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm including hydraulic lateral ramp shifting and load holding valve * Loading area above the turntable: approx. 2,990 x 2,520 mm * rear loading area: approx. 6,780 x 2,520 mm * loading height incl. Approx. 890 mm, +/- 20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, bogie, ramps, folding boom and mechanical support supports hot-dip galvanized * Axles, pull scissors, air tank and slewing ring painted in a black tone * Tires 235/75 R 17.5 * New vehicle without first registration with manufacturer's warranty *

Condition: new, overall weight: 14,400 kg, maximum load weight: 10,360 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 14.4: * RDÜ (tire pressure monitoring with display option in the truck via EBS signal without truck-side installation) * electronic braking system EBS * emergency release device for spring-loaded cylinders * drum brakes * 2 x 5.5 ton. Gigant axles * Air suspension with lifting and lowering system * Height-adjustable drawbar by 300 mm * Jost support winch at the front * External hot-dip galvanized folding supports at the rear * Plastic toolbox at the front right on the outside of the bulkhead * Side impact protection * Plastic quarter fender * LED lighting system * 15-pin power plug * Hot-dip galvanized chassis as well as drawbar, bulkhead and rear wall * 50 mm softwood floor * Device for subsequent installation of 20" cont. locks at the front and rear Dujlendpn Seraa E Ijt * Screwed bulkhead made of smooth sheet metal * Side walls made of sheet steel - trapezoidal profile - foldable with side wall spring lifter * Hot-dip galvanized rear stanchions screwed * Perforated outer frame bent at approx. 45 degrees with 2 ton lashing force every 480 mm, installation of 3 ton lashing brackets every 600 mm possible, 1 x 6.3 ton lashing ring in the front and rear corners, various holes in the front and end beams for 1.2 ton lashing option * 1 pair of aluminum docking ramps approx. 3,310 x 400 mm (load capacity 8 ton / pair) suitable for rubber-tired and tracked vehicles, storage compartment below the loading area in the chassis from the rear * Vehicle hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available from week 19/2025 from Egestorf

Condition: new, overall weight: 30,000 kg, maximum load weight: 23,500 kg, axle configuration: 3 axles, loading space length: 8,380 mm, loading space width: 2,520 mm, Year of construction: 2024, * PT 30 profile: * EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 tonne Gigant axles * Air suspension with lifting and lowering system and RtR valve * Smart board mounted on the trailer as an information tool (for axle load display - front and rear separately) * Tire pressure monitoring with display option in the truck via EBS signal without truck-side installation * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fender with splash guard * Rear straight galvanized. Sheet steel aprons with splash guard * Reflective contour tape on the side and rear * 15-pin power plug * LED lighting 12/24 V * LED rotating beacon (removable) at the rear * Pull scissors 1,200 mm long with 40 mm pull eye and height adjustment via tension spring & turnbuckle * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm, black powder-coated on the right side * Box in the bogie for accessories with hinged lid, 2 cont. locks permanently installed (directly after the bogie platform) * ROBOT welded ANTI-SLIP coating on the steel plate of the bogie platform (protruding weld beads) * La-Si package consisting of: 2 lashing eyes (13.4 tonnes) at the front left & right on the bulkhead support, front & rear 1 pair of UVV lashing rings (13.4 to.) and 3 pairs of UVV lashing rings (10 to.) on the side, swiveling and lowerable, loadable in all directions and embedded in the outer frame, 3 stake pockets on the side with simultaneous 2 ton lashing option * 6 pairs of mechanical folding booms for 3 m total width (but not in the rear slope) * Widening planks placed in the middle of the loading area * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm Dolrajrwc R Hsa E Isut * Mechanically laterally adjustable * 4-way control block for later retrofitting of hydraulic. Ramp shift * Chassis, bogie, folding boom, drop supports and ramps hot-dip galvanized * Axles, slewing ring, air tank, drawbar painted in a black tone * Loading edge when loaded approx. 910 mm +/- 20 mm air suspension, * New vehicle with manufacturer's warranty * Errors and interim purchase subject to reservation * Available for immediate delivery from Egestorf

Condition: new, overall weight: 30,000 kg, maximum load weight: 24,100 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2024, * T3 profile 30.0: * EBS brake system * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles * Parabolic springs * Mechanical axle compensation at the rear Dslrajl Th Adsa E Isut * Lateral impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle closed plastic mudguard and rear axle straight galvanized. Steel sheet aprons each with splash guard * Reflective contour tape on the side and rear * Hinged lid (hot-dip galvanized) for the toolbox in the bogie platform * Multi-voltage system * LED tail lights * Rotating beacon (removable) at the rear * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * 15-pin power plug * 4 stanchion pockets on each side (but no stanchions available) with simultaneous lashing option * La-Si package consisting of: 2 lashing eyes (6.4 tons) at the front left & right on the main frame of the bogie platform, 5 pairs of UVV lashing rings that can be swiveled and lowered, can be loaded in all directions and are embedded in the outer frame - 13.4 tons in the corners, otherwise 10 tons * 6 pairs of mechanical folding booms for 3 mtr. Total width (but not in the rear slope) * Widening planks placed in the middle of the loading area * Excavator boom shelf above rear axle to the end beam approx. 2,100 mm long (2 pairs of 6.4 ton lashing rings on the side in the excavator boom shelf) * Hydraulic one-piece loading ramps (approx. 3,000 x 720 mm) laterally adjustable * Loading area above the turntable: approx. 1,960 x 2,520 mm * Loading height when unloaded approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Loading height when unloaded approx. 910 mm (incl. 860 mm approach slope) * Chassis, bogie, scissors and loading ramps hot-dip galvanized * Axles, springs, air tanks etc. painted in a black tone * 235/75 R 17.5 twin tires * 5,900 kg empty weight * --total permissible weight of 30,000 kg technically possible-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * available immediately from Egestorf

Condition: new, overall weight: 30,000 kg, maximum load weight: 23,700 kg, axle configuration: 3 axles, Year of construction: 2024, * T3 Profi 30.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles * Air suspension with manual lowering at the rear * Pressure gauge pressure display for determining the load weight (axles separated into 2 air suspension circuits), * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle closed. Plastic fenders and rear straight galvanized sheet steel aprons, each with splash guard * Reflective contour tape on the side and rear * Hinged lid (hot-dip galvanized) for the toolbox in the bogie platform * LED tail lights * Rotating beacon (removable) at the rear * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * 2 x 7-pin power plugs * 4 stake pockets on each side with simultaneous 2 ton lashing option * La-Si package consisting of: 2 lashing eyes (6.4 ton) at the front left & right on the main frame of the bogie platform, 5 pairs of UVV lashing rings that can be swiveled and lowered, can be loaded in all directions and are embedded in the outer frame - 13.4 ton in the corners, otherwise 10 ton * 6 pairs of mechanical folding booms for 3 mtr. Total width (but not in the rear slope) * Widening planks placed in the middle of the loading area * hydr. one-piece loading ramps (approx. 3,000 x 720 mm) laterally adjustable Dujlel Tq Eueraa E Iet * Loading area above the turntable: approx. 1,960 x 2,520 mm * Loading height unloaded approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Loading height unloaded approx. 910 mm (incl. 860 mm approach slope) * Chassis, bogie, drawbar, folding extensions & loading ramps hot-dip galvanized * Axles, turntable, air tank etc. painted in a black tone * Tires 235/75 R 17.5 * Payload approx. 24,000 kg with 30,000 kg total weight * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, overall weight: 30,000 kg, maximum load weight: 16,400 kg, axle configuration: 3 axles, Year of construction: 2024, * T3 profile 30.0: * EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles * Air suspension with lifting and lowering system * SmartBoard as an information tool on the trailer with pressure sensors for pressure display for total axle load display for each axle group * Side impact protection * Mechanically adjustable warning sign packages at the front and rear * Front axle closed. Plastic fenders and rear straight galvanized sheet steel aprons, each with splash guard * Hinged lid (hot-dip galvanized) for the tool box in the bogie platform * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm (black powder-coated) on the right side * 15-pin power plug * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * Side marker lights with indicator control * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * Tire pressure monitoring system with display option in the truck via EBS signal (without truck-side installation) * Rubber covering on the folding ramps and on the ramp on the left and right (approx. 860 mm long) * Rubber covering on the longitudinal beams from the front to the end beam * Hardwood floor on the running surfaces of the low-loading platform * 4 stake pockets on each side with a simultaneous 2 ton. Lashing option * La-Si package consisting of: 5 pairs of UVV lashing rings that can be swiveled and lowered, can be loaded in all directions and are embedded in the outer frame - 13.4 tons in the corners, otherwise 10 tons * 6 pairs of mechanical folding booms for 3 m total width (but not in the rear slope) * Plank holder under the loading area in the longitudinal direction * Roller stop raised in front of the front beam with 1 x 6.4 ton lashing eye on each side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable tip section and load holding valves * Hydraulic lateral ramp shifting * Hydraulic rear support (single-stage cylinder) * Hydraulic. Flow divider in the trailer (with hydraulic pump output in the truck of over 40 liters up to max. 140 liters/min.) * Hydraulic control block splash-proof * Two-line hydraulics * Loading area above the turntable: approx. 1,960 x 2,520 mm, Dolraa Estplv Nj Iout * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm approach slope) * Loading height when loaded approx. 890 mm +/- 20 mm air suspension * Chassis, bogie, roller stop, folding extensions & ramps hot-dip galvanized. * Axles, turntable, pull scissors, air tank etc. painted in a black tone * Loading height when loaded: approx. 890mm +/- 20mm * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: new, overall weight: 30,000 kg, maximum load weight: 24,100 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2024, * T3 profile 30.0: * EBS brake system * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles * Parabolic springs * Mechanical axle compensation at the rear * Lateral impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle closed plastic mudguard and rear axle straight galvanized. Steel sheet aprons each with splash guard * Reflective contour tape on the side and rear * Hinged lid (hot-dip galvanized) for the toolbox in the bogie platform * Multi-voltage system * LED tail lights * Rotating beacon (removable) at the rear * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * 15-pin power plug * 4 stanchion pockets on each side (but no stanchions available) with simultaneous lashing option * La-Si package consisting of: 2 lashing eyes (6.4 tons) at the front left & right on the main frame of the bogie platform, 5 pairs of UVV lashing rings that can be swiveled and lowered, can be loaded in all directions and are embedded in the outer frame - 13.4 tons in the corners, otherwise 10 tons * 6 pairs of mechanical folding booms for 3 mtr. Total width (but not in the rear slope) * Widening planks placed in the middle of the loading area * Excavator boom shelf above rear axle to the end beam approx. 2,100 mm long (2 pairs of 6.4 ton lashing rings on the side in the excavator boom shelf) Delraa Ejl Thxae Ijut * Hydraulic one-piece loading ramps (approx. 3,000 x 720 mm) laterally adjustable * Loading area above the turntable: approx. 1,960 x 2,520 mm * Loading height when unloaded approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Loading height when unloaded approx. 910 mm (incl. 860 mm approach slope) * Chassis, bogie, scissors and loading ramps hot-dip galvanized * Axles, springs, air tanks etc. painted in a black tone * 235/75 R 17.5 twin tires * 5,900 kg empty weight * --total permissible weight of 30,000 kg technically possible-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * available immediately from Egestorf