Low loader trailer

MÜLLER-MITTELTAL T3 Tiefl., Luft., Schwarzdeckentransporte

Condition: new, maximum load weight: 16,400 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2024, * T3 profile 30.0: * EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles * Air suspension with lifting and lowering system * SmartBoard as an information tool on the trailer with pressure sensors for pressure display for total axle load display for each axle group * Side impact protection * Mechanically adjustable warning sign packages at the front and rear * Front axle closed. Plastic fenders and rear straight galvanized sheet steel aprons, each with splash guard * Hinged lid (hot-dip galvanized) for the tool box in the bogie platform * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm (black powder-coated) on the right side * 15-pin power plug * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * Side marker lights with indicator control * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * Tire pressure monitoring system with display option in the truck via EBS signal (without truck-side installation) * Rubber covering on the folding ramps and on the ramp on the left and right (approx. 860 mm long) * Rubber covering on the longitudinal beams from the front to the end beam Fpjdoq Dyvcspfx Afmep * Hardwood floor on the running surfaces of the low-loading platform * 4 stake pockets on each side with a simultaneous 2 ton. Lashing option * La-Si package consisting of: 5 pairs of UVV lashing rings that can be swiveled and lowered, can be loaded in all directions and are embedded in the outer frame - 13.4 tons in the corners, otherwise 10 tons * 6 pairs of mechanical folding booms for 3 m total width (but not in the rear slope) * Plank holder under the loading area in the longitudinal direction * Roller stop raised in front of the front beam with 1 x 6.4 ton lashing eye on each side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable tip section and load holding valves * Hydraulic lateral ramp shifting * Hydraulic rear support (single-stage cylinder) * Hydraulic. Flow divider in the trailer (with hydraulic pump output in the truck of over 40 liters up to max. 140 liters/min.) * Hydraulic control block splash-proof * Two-line hydraulics * Loading area above the turntable: approx. 1,960 x 2,520 mm, * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm approach slope) * Loading height when loaded approx. 890 mm +/- 20 mm air suspension * Chassis, bogie, roller stop, folding extensions & ramps hot-dip galvanized. * Axles, turntable, pull scissors, air tank etc. painted in a black tone * Loading height when loaded: approx. 890mm +/- 20mm * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: used, Equipment: soot filter, - Air conditioning- 3x shovels- Powertilt- Top conditionSuspension: Fodpfx Afjvdpn Tomjpp Hydraulic

Condition: used, machine/vehicle number: GE11/142/2022, empty load weight: 6,350 kg, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, first registration: 08/2008, loading space length: 8,500 mm, loading space width: 2,500 mm, suspension: air, Very well preserved vehicle from 1st hand Three-axle drive-over low loader trailer Low loader with drive-on ramp Heavy load transport Type T3 Komakt 30.0 Length 8500 mm Width 2500 mm Air suspension Commercial/export net price - 19990 € Changes, prior sale and errors reserved ===== Telephone2 Mobile phone Fpedpjn Aw Hkjfx Afmsp =====

Condition: new, power: 294 kW (399.73 HP), fuel type: diesel, axle configuration: 6x6, tire size: 315/80R22.5, fuel: diesel, wheelbase: 20,240 mm, driver cabin: day cab, gearing type: automatic, emission class: euro2, suspension: steel, Equipment: air conditioning, all wheel drive, = More options and accessories = - Leaf suspension = Remarks = Model year: 2024 = Company information = Van Vliet Automotive Trading - Your Truck Partner A wide range of new trucks, trailers, 4x4s and machines. Ready to use immediately! Our own (design) workshops, modification center and paint shop guarantee you a fast and project-appropriate processing of your order, anywhere in the world. ISO and AEO certified. Logistical processing and customs/export facilities. Worldwide spare parts service. International mechanic and training team operating on site worldwide to provide technical support and training. Contact our experienced, multilingual team of account managers now for professional, project-specific and competitive advice. Fpedpevpqcijfx Afmjp = More information = Gearbox: TipMatic 12.28OD, automatic Model year: 2024 Tire size: 315/80R22.5 Suspension: leaf spring = Company information = WE PROVIDE, YOU ACCELERATE Without boundaries Van Vliet is the official MAN Truck & Bus SE importer for several African countries. Supported with careful after sales services, such as supplying parts and providing (local) trainings. WE PROVIDE, YOU ACCELERATE Without boundaries Van Vliet is the official MAN Truck & Bus SE importer for several African countries. Supported with careful after sales services, such as supplying parts and providing (local) trainings.

Condition: used, functionality: fully functional, mileage: 193,000 km, power: 130 kW (176.75 HP), gearing type: semi-automatic, fuel type: diesel, color: orange, overall weight: 12,500 kg, empty load weight: 7,000 kg, number of seats: 2, first registration: 06/2002, next inspection (TÜV): 10/2025, Year of construction: 2002, Equipment: ABS, additional headlights, air conditioning, all wheel drive, cabin, cruise control, differential lock, standard shovel, trailer coupling, We are selling our Unimog U 400 including winter service equipment (3m snow plow and salt spreader with brine). Fuel: Diesel Color: Orange First registration: 18.06.2002 Additional heat exchanger at the rear TÜV/SP will be renewed by us Every year in October, the Unimog has been taken to the workshop. All defective parts were replaced, maintenance service carried out, and TÜV inspection performed. Fjdpfewtnnijx Afmepp

Condition: new, machine/vehicle number: 2dff0c136c85096f36822a0bb, empty load weight: 7,150 kg, maximum load weight: 16,850 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points each 10 to integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Fjdji Riy Eepfx Afmjpp Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation axle load compensation (rocker compensation) Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-loaded parking brake Incl. 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 8,200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Incl. with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: used, mileage: 1 km, first registration: 01/1997, Manufacturer: Schmidt Nido Type: SNK -s additional equipment: - lighting - bearing block Fpjdpfsvvqnljx Afmop - 12V hydraulic unit

Condition: new, maximum load weight: 23,500 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2026, Equipment: ABS, * T 3: * ABS brake system * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical axle compensation at the rear * Side underrun protection * Swivel support legs at the rear of the chassis frame * Mechanically adjustable warning sign holders front & rear * Front axle with closed plastic mudguards, rear axle with straight galvanized steel skirts, each with spray protection * Reflective contour marking tape on the sides and rear * Folding (hot-dip galvanized) toolbox lid in the turntable platform * Toolbox made of galvanized steel sheet approx. 650 x 300 x 600 mm - powder-coated black - fitted laterally under the chassis * 15-pin power connector * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * Drawbar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * Four stake pockets on each side (no stakes present) with lashing capability * Load securing package consisting of: 2 lashing eyes (6.4 t) front left & right on the main frame of the turntable platform * 5 pairs of UVV-compliant swing-out and retractable lashing rings * Loadable in all directions and integrated into the outer frame at the corners (13.4 t), elsewhere 10 t * 6 pairs of mechanical fold-out outriggers for total width of 3 m (not in the rear slope) Fedpfx Asq Dyv Iofmjpp * Widening planks stored in a compartment under the loading surface * Excavator arm support over the rear axle up to the end cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings laterally in the excavator arm support) * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically folding ramp tips and load holding valves, hydraulically lateral ramp displacement * Hydraulic flow divider in the trailer (for truck hydraulic pump output over 40 l/min up to max. 140 l/min), dual-line hydraulic system * Loading area above the slewing ring: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm approach slope) * Loaded platform height approx. 860 mm +/- 30 mm (compensation unit) * Chassis, turntable, folding outriggers, rear drop supports and ramps hot-dip galvanized * Axles, springs, drawbar, air tanks etc. painted in black * New vehicle with manufacturer warranty * Errors and prior sale excepted * Available from CW 03/2026