Used Fliegl Tipper Semitrailers for sale (299)

Condition: new, overall weight: 41,000 kg, empty load weight: 9,800 kg, maximum load weight: 31,200 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: dc46d2e1cd272305b99fb3160, Further information Vehicle consisting of: Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with interchangeable 2 kingpin and 2 kingpin positions 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2 wheel chocks with holder Aluminum side collision protection Quarter-shell mudguards in front of and behind axle unit 1st pair of wheel recesses after gooseneck recessed in the low bed of the tramline area, slanted towards the entrance. Length at bottom approx. 1600 mm, depth of wheel recesses approx. 260 mm. Note! Frame in main beam area 260 mm higher than wheel recess. 2nd pair of wheel recesses between A and B axle. Bottom length approx. 350 mm, depth approx. 260 mm. Note! Frame in main carrier area 260 mm higher than wheel recess. If wheel loaders are to be driven and the overall height is to be checked, we request a technical data sheet for the wheel loader types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses are required by the customer). Wheel recess cover can be pulled out from the main frame, with wooden inserts. Widenings extendable to 3,000 mm (not in the rear slope and not in the wheel recesses below) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks on gooseneck, front transverse Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 2 pairs of ring lashing eyes, 5 tons each at the front on the gooseneck 11 pairs of lashing rings at the top and sides, each 10 tons, embedded in the outer frame 2 x on gooseneck9 x in low loader bed distributed first lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm Cgeb Hji Ri Hcon Humst 8 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, or instead of stake pockets 5 to. Ring lashing eyes embedded in the floor Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, without connecting cable with lifting & lowering valve Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle - driving stability system Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1 x LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm, removable with plug Floor Gooseneck with steel / checker plate covering Storage box embedded in drive-over slope to gooseneck Then with 70 mm softwood floor, in the wheel recesses underneath and in the wheel

Condition: new, overall weight: 50 kg, empty load weight: 14 kg, maximum load weight: 35 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: 5c7120ea17bcf92d3b69899da, Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with exchangeable 2 king pins 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2x wheel chocks with holder Aluminum side collision protection Quarter-shell mudguards in front of and behind axle unit with spray flaps behind each axle 1x storage box Box, w=2 350 mm x l=730 mm x h=640 mm, bolted transversely at the front to the floor of the gooseneck, with 2 storage trays Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks on gooseneck, front transverse Wooden planks 70 mm for widening to 3000 mm Excavator trough above the rear axles starting to the rear, approx. 500 mm wide and approx. 230 mm deep Low loader lashing eyes 3 pairs of lashing eyes per 10 tons at the front gooseneck, 8 pairs of lashing eyes per 10 tons in the low bed, 3 pairs of lashing strips in the tramline area of the low bed, 3 pairs of lashing eyes per 10 tons in the axle/rear area Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Hydraulic forced steering via saddle deflection wedge acting on all 3 axles, Post-steering with radio remote control + auto toe-in, (up to max. 20 km/h)Note! A 2-pin Nato socket with at least 2 x 35 mm² is required in the truck for the power supply to the steering system. Power is supplied to the pump unit via a Nato connection cable to the towing vehicle, without truck installation (re-steering must be used once a week). Air suspension Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, without connecting cable With lifting & lowering valve, hold function in lowering position + auto-reset function Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle driving stability system Trailer Infocenter, for displaying vehicle data such as axle loads (no calibrated scales), mileage and diagnostic/system messages. Cgob Hn Huji Ri Hgjmet Electrics 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white LED position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1x additional LED work light(s) at the rear, switched via reversing light 1x LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Gooseneck with steel / checker plate covering In the tramline area with 70 mm softwood floor, in the wheel housing area with steel / checker plate covering, low bed can be raised hydraulically on the left and right in the tramline area for entry, via truck auxiliary drive Rear slope with 70 mm softwood floor Drop deck length approx. 6,300 mm Drop sides 25 mm aluminum h

Condition: used, overall weight: 35,000 kg, empty load weight: 6,115 kg, maximum load weight: 28,885 kg, axle configuration: 3 axles, first registration: 11/2015, tire size: 385/55 r 19,5, machine/vehicle number: a7d2a8dfe0e7c5ca8550173af, Further information 6 vehicles available - 6 vehicles available! - 6 vehicles available! - 6 vehicles available! - 6 vehicles available! Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins, outer frame slightly slanted with load-lock profile for lashing strapsNote! To attach the straps in conjunction with drop sides, the drop sides must be opened! Pair of additional lashing eyes embedded in the outer frame, 2.5 tons each, outer frame with Load-Lock profile for attaching tensioning strapsNote! Cannot be used with drop sides! 24 t. 2-speed support winch, single-side operation, with semicircular lower section and straight connecting plate, with thrust compensation, telescopic rear support, mounted as high as possible, extension ladder at the rear, door locks on the side Wheel chocks with holder, aluminium side bumpers, galvanized steel underride guard, quarter-shell mudguards in front of 1st axle and behind each axle, with anti-spray flaps behind each axle, rear impact protection, heavy blocker rear transverse impact protection, pallet stop on both sides approx. 20 - 25 mm high, bolted design, loading height reduced by approx. 20 - 25 mm, plastic tool box, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included), document box, storage box for fire extinguisher up to 6 kg, fire extinguisher (ABC powder 6 kg) SAF disc brake axles, hubodometer/kilometer counter, air suspension, 1st axle automatic lift axle, can also be operated electrically from the truck, with starting aid, without truck installation (with starting aid up to max. 25 km/h) Axle lift below the recomm. Driving height, therefore no warranty for tire damage 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable coupling heads and Duomatic connection at the front, without connecting cable, EBS made by Wabco, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer vehicle may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve + auto-reset function, ride height in conjunction with lift axle, when the lift axle is raised, the loading or total height increases by 50 mm (with lift axle).total height increases by 50 mm (with Mega Flex only with low ride height or semi-mounted height), vehicle ride stability system 24 volt, 4 x 3 chamber lights + 1 round reversing light and + 1 round rear fog light, amber LED lighting at the side, amber LED lighting at the side with 20 LED diodes per light, 2 white position lights at the front 2 white/red lane departure warning lights at the rear, 2 x 7-pin and 1 x 15-pin interchangeable front sockets, without connecting cable, Cargobull TrailerConnect, as offered, supplied loose for self-assembly LED safelight, top in rear corner stanchions Screen printing plates approx. 30 mm thick, cross joints with Omega inlay, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Front wall/front corner stanchions 2,780 mm high, steel corner stanchions in volume design, release device for side tarpaulin on front wall, bottom inside at approx. 140 mm height with steel impact protection Ceb Hsi Ri S Eon Humegt 2 pairs of sliding stanchions can be moved over the entire length, without insertion pockets, 2 pairs of stanchion positions, rear wall/rear stanchions, rear steel corner stanchions up to lower edge of roof, attachment for tarpaulin with round tube

Condition: new, overall weight: 28,000 kg, empty load weight: 5,800 kg, maximum load weight: 22,200 kg, axle configuration: 2 axles, tire size: 235/75 r17,5, machine/vehicle number: 1acf251a278ec5cde4067a7b1, Further information Chassis saddle forwarding Fine-grained steel welded construction, saddle plate with replaceable 2 king pins Outer frame slightly slanted new design with Load-Lock profile for tensioning strap attachment 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Free support foot corner dimension or free swing radius to the rear approx. 1920 mm 2 wheel chocks with holder Aluminum side impact guard Steel underride guard Quarter-shell mudguards in front of and behind each axle 1 spare wheel holder for 1 e-wheel, with wheel fastening set 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Axles + suspension Drum brake axles of the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-applied parking brake Duomatic connection at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 235/75 R17.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin socket at the front, without connecting cable Floor Screen printing plates approx. 30 mm thick, for high point load capacity for forklift axle load up to max. 5,600 kg Front wall / front corner stanchions Ceb Hn Hskv Uvzjumjgt 25 mm aluminum hollow profile, approx. 1 350 mm high, steel corner stanchions in volume design Approval country / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Front wall aluminum Attention! These are archive pictures!

Condition: used, overall weight: 29,000 kg, empty load weight: 5,380 kg, maximum load weight: 23,205 kg, axle configuration: 3 axles, first registration: 03/2021, tire size: 435/50 r19,5, machine/vehicle number: d97bfb41327ce44dcbe8c5fc6, Further information Fine-grained steel welded construction, saddle plate with replaceable 2 king pins, outer frame slightly inclined with load-lock profile for attaching tensioning strapsNote! to attach the straps in conjunction with drop sides, the drop sides must be opened! 24 t. 2-speed support winch, single-sided operation, with semicircular lower section and straight connecting plate, with thrust compensation, extension ladder at the rear, door locks on the side, wheel chocks with holder Aluminium side bumpers, galvanized steel underride guard, quarter-shell mudguards in front of 1st axle and behind each axle, with anti-spray flaps behind each axle, heavy blocker rear bumper + side roller bumpers, 2 spare wheel holders for 1 e-wheel, with wheel fastening set, 1 spare wheel steel rim, 2 plastic toolboxes BPW disc brake axles, axle/chassis laser-measured Reduction in tire wear and fuel consumption, air suspension 2-line compressed air brake system, spring-loaded parking brake, 2 swap-proof coupling heads at the front, without connecting cable, EBS made by Wabco, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer vehicle may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, vehicle driving stability system, tire pressure monitoring system IVTM Wabco, via EBS, without truck installation (prerequisite for this must be given in the truck). 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front 2 white/red lane departure warning lights at the rear, 2 x 7-pin and 1 x 15-pin interchangeable sockets at the front, without connecting cable Floor: Screen printing plates approx. 30 mm thick, cross joints with Omega inlay, on longitudinal beams for high point load capacity for forklift axle load up to max. 7,100 kg Front bulkhead / stanchions at the front: 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, Crash blocker, bottom inside at approx. 140 mm height with steel impact protection Middle stanchions: 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and long pocket at the bottom, 3 pairs of stanchion positions, aluminum insertion slats Rear steel corner stanchions up to lower edge of roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin with welded-in horizontal and vertical straps, stainless steel tensioning fasteners Customs rope all-round with holder on the bulkhead (no customs lock, not in conjunction with Quick Lock) Cgob Hekyrl Nsn Humjt Roof: sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-roof rail for automotive industry, internal width between the roof rails approx. 2,490 mm, tarpaulin color: white, EcoLift - lifting roof can be raised by approx. 380 mm, on both sides, with gas pressure damper support, 3 driving positions at the front: internal height at the front approx. 2,900 mm/2,950 mm/3,000 mm, adjusted to approx. 2,950 mm Optimum rain bar at the rear, at the top of the end bows, above the doors Germany, test approval according to EC 2007/46, load securing certificate according to EN 12642 XL (only valid in conjunction with 4 rows of aluminum slats), 24/7 service hotline, prepared for single-line license plate holder, warning sign according to EC

Condition: used, overall weight: 35,000 kg, empty load weight: 6,115 kg, maximum load weight: 28,885 kg, axle configuration: 3 axles, first registration: 08/2017, tire size: 385/55 r19,5, machine/vehicle number: d87cbe0bb9e6c21d07ec01e81, Further information Welded fine-grained steel construction, saddle plate with replaceable 2 king pins, 13 pairs of lashing eyes additionally embedded in the outer frame, each 2.5 tons Outer frame with Load-Lock profile for lashing strap attachment, Note! Cannot be used with drop sides! 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation, pull-out ladder at the rear, door locks on the side, wheel chocks with holder, aluminium side collision protection, galvanized steel underride guard, quarter-shell mudguards in front of the first axle and behind each axle, with anti-spray flaps behind each axle, impact protection at the rear, pallet stop on both sides approx. 20 - 25 mm high, bolted design, loading height reduced by approx. 20 - 25 mm, plastic tool box SAF disc brake axles, air suspension 2-line air brake system, spring-loaded parking brake, 2 interchangeable coupling heads at the front, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, with lifting & lowering valve, vehicle stability system, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Csb Hn Hekyrmbsumegt 24 volt electrics, multi-chamber lights, amber LED lighting at the sides, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable sockets at the front, without connecting cable Floor: Screen printing plates approx. 30 mm thick, cross joints with Omega inlay, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Front bulkhead/front stanchions: 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, bottom inside at approx. 140 mm height with steel impact protection Middle stanchions: 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and long pocket at the bottom, aluminum insertion slats Rear steel corner stanchions up to lower edge of roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin with welded-in horizontal and vertical straps, stainless steel tension locks, RPS labeling Roof: sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-roof rail for automotive industry, internal width between the roof rails approx. 2,490 mm, tarpaulin color: white, EcoLift - lifting roof can be raised by approx. 380 mm, one side in FR-left (front both sides) with gas pressure damper support, 2 driving positions at the front: internal height at the front approx. 2900 mm / 3000 mm, Approval country: Germany, test approval according to EC 2007/46, load securing certificate according to EN 12642 XL (only valid in conjunction with 4 rows of aluminum slats), additional DC 9.5 certificate, 24/7 service hotline, prepared for license plate holder single-line, warning sign according to ECE - 70, reflective stripes: white, on the side tarpaulin at the bottom and at the top in the corners Reflective stripes: red, all-round on the rear portal

Condition: new, overall weight: 2,500 kg, empty load weight: 760 kg, maximum load weight: 1,740 kg, axle configuration: 1 axle, tire size: 235 / 75 r 17,5, machine/vehicle number: 5067caac5acaa655d1d94bd2d, Further information Chassis central axle trailer Fine-grained steel welded constructionincl. 4 mounting points for IBC containers if technically possible Drawing approval required from the customer if ordered! 2 side members as double T-beams for subsequent self-supporting superstructure with front cross member Cjbsi Ri Ano Hn Humjgt 2 pairs of lashing eyes for lashing the IBC container Telescopic support foot at the front Wheel chocks with holder Mudguards without side bumpers Steel underride guard Towing device central axle trailer Towbar with tested 40 mm towing eye, forwarding version Height-adjustable drawbar via spindle, max. adjustment range 250 mm Axles + suspension GFA or BPW axle of the manufacturer's choice, with angular roller bearings and S-cam brake Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, without ABS, but with mechanical ALB, then max. 60 km/h approval Electrical system 24 volt, multi-chamber lights, without amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Country of registration / plates Country of registration: Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Attention! These are archive pictures.

Condition: new, overall weight: 18 kg, empty load weight: 3 kg, maximum load weight: 14 kg, axle configuration: 2 axles, tire size: 265/70 r19,5, machine/vehicle number: 65c7289da24c6dbb3dde7c971, Further information Chassis Wechel central axle trailer Fine-grained steel welded construction Cgsbsi Rixcs Hn Humjt Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 1 pair of gear support legs at the front, with straight lower section, support leg can be operated separately on the left and right Wheel chocks with holder Aluminum side bumper Steel underride guard Half-shell mudguards Towing device central axle trailer Tow bar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or exact testing still required in the event of an order) Without length adjustment of drawbar Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-applied parking brake Duomatic connection at the front, with connection line to the engine trolley, connection in FR-right EBS, electronic brake system with EBS plug at the front, with connecting cable, connection in FR right-hand side Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Wheels and tires 265/70 R19.5 tires of the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 15-pin plug at the front, with connecting cable, connection in FR right-hand side Additional LED work light(s) at the rear, switched via reversing light LED work lights at the front, centered between the carriers, radiating to the rear, switched via reversing light Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Attention: Archive pictures!

Condition: used, overall weight: 18,000 kg, empty load weight: 2,620 kg, maximum load weight: 15,380 kg, axle configuration: 2 axles, first registration: 04/2019, tire size: 385/65 r22,5, Year of construction: 2019, machine/vehicle number: 9a9c8ebe1f7e791f4fc6f94e6, Further information Welded fine-grained steel construction, front stop, longitudinally adjustable and foldable, pair of removable guide rollers, front and rear, pair of removable guide rollers, additional 4 container locks with sturdy outriggers on 20-base for swap bodies 7.15 and 7.45, turntable with strong ball bearing slewing ring, wheel chocks with holder Aluminum side bumpers, steel underride guard, quarter-shell mudguards at the front and half-shell mudguards at the rear 1 spare wheel holder for 1 e-wheel, with wheel fastening set in basket design Drawbar with tested 40 mm drawbar eye, drawbar height adjustment via spring Cgeb Hnji Riz He Humot BPW disc brake axles, axle/chassis laser-measured Reduction in tire wear and fuel consumption, air suspension 2-line compressed air brake systemColor-coded line routing for easy servicing. Air supply 208 liters Spring-loaded parking brake, 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, EBS made by Wabco, electronic brake system with EBS plug at the front, with connecting cable, (Attention: The trailer vehicle may only be towed by towing vehicles that guarantee the effectiveness of the ABS!) with lifting & lowering valve, holding function in the lowering / lifting position in each case 24 volt, 4 x 3 chamber lights + 1 round reversing light + 1 round rear fog light, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 1 x 15-pin plug at the front, with connecting cable, 1 additional LED work light(s) at the rear, switched via reversing light, 1 LED work light at the front in the middle between the beams, radiating to the rear, switched via reversing light Country of registration: Germany, with Dekra approval and certificate (according to §13 EG - FGV), prepared for single-line license plate holder, contour markings with reflective strips according to ECE R 048, white at the sides and red at the rear

Condition: new, overall weight: 18 kg, empty load weight: 3 kg, maximum load weight: 14 kg, axle configuration: 2 axles, tire size: 445/45 r19,5, machine/vehicle number: 1eb6bdba4d54d87ab018b84c2, Further information Chassis Wechel central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 1 pair of gear support legs at the front, with straight lower section and single-sided operation in FR right 2 wheel chocks with holder Aluminum side bumpers Steel underride guard Half-shell mudguard Spray flaps Csb Hn Huoi Ri Itemsgt Towing device central axle trailer Towbar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or exact testing still required in the event of an order) Without length adjustment of drawbar Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Air supply 208 liters Spring-applied parking brake Duomatic connection at the front, with connection line to the motor vehicle, connection in FR-left EBS, electronic braking system with EBS plug at the front, with connecting cable, connection in FR right-hand side Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in both lowering / lifting position Wheels and tires 445/45 R19.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, connection in FR right-hand side LED work lights on both sides (switched via reversing light) LED worklights at the front, centered between the carriers, radiating to the rear, switched via reversing light Operating instructions Special approval required if the overall length of the train exceeds 18,750 mm. Observe country-specific approval regulations. Country of approval / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Attention: Archive pictures!

Condition: new, overall weight: 24,000 kg, empty load weight: 7,150 kg, maximum load weight: 16,850 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: 2dff0c136c85096f36822a0bb, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Cjb Hnsi Riy Eo Humsgt Folding rear support 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points each 10 to integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation axle load compensation (rocker compensation) Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-loaded parking brake Incl. 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 8,200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Incl. with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, overall weight: 24,000 kg, empty load weight: 10,280 kg, maximum load weight: 13,720 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: ee3256d63dd23b3ad1bdf9ab0, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 storage box on offset recessed in the floor with cover, W=720 mm/ L=520 mm / D= 170 mm 1st pair of wheel recesses recessed in the low bed in the tramline area after the offset, sloping towards the entrance, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area 400 mm higher than wheel recess.2nd pair of wheel recesses between the axles in the drop center in the tramline area, slanted towards the entrance, length at the bottom approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Wheel well cover can be pulled out from the main frame, with wooden inserts. Distance from main frame beam to beam outside approx. 1280 mm (wheel well area) Widenings extendable to 3,000 mm, foldable on the wheel recess extensions (widening not in the rear slope and not in the wheel recesses below) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed or under the cargo bed if technically possible Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 8 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 2 x at the front on the offset 6 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye with 8° inclined drawbar eye Ceb Hn Hji Ri I Njumsgt Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension with lift & lower valve can be operated separately at the front and rear Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Trailer Infocenter, for displaying vehicle data such as axle load (no calibrated scales) and odometer Axle load detection via EBS-Canbus signal, for display in the driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Vehicle - driving stability system Duomatic connection at the front, with connecting cable to the truck, EBS, electronic braking system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights in LED with resistor, amber LED lighting on the side, license plate lighting in LED, (Note! with certain towing vehicles, misdiagnoses may occur even though the function is given) 2 white front position lights in LED 2 white/red rear lane departure ligh

Condition: new, overall weight: 18 kg, empty load weight: 5 kg, maximum load weight: 12 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: 2b58968e34fac93b429a256e9, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support Wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Quarter-shell mudguards in front of 1st axle Spare wheel holder for 1 electric wheel, with wheel mounting kit Spare wheel, same make as basic tires, steel rim Plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Low loader lashing eyes 3 pairs of lashing points, each 10 tons, integrated in the floor at the front 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x according to the rest of the neck area, distributed between them, spacing not greater than 1200 mm 1 x rear bevel 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets) Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cableVoltage converter for 12/24 volt operationNote! A 7-pin 12 volt socket is required on the tractor/tractor! (Required in conjunction with electrical voltage converter!) Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white/red rear lane departure lights 2 white position lights at the front Additional LED work light(s) at the rear, switched via reversing light 2 x 7-pin interchangeable plugs at the front, with connecting cable1 x 7-pin agricultural plugVoltage converter 12/24 volt (only for electrics, not for ABS/EBS) Floor Front area steel floor, then with 70 mm softwood floor, steel/ checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Ceb Hn Hsi Ri Nxoumjgt Operating instructions A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give an approval for 20 t GG. Customer risk. Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: used, overall weight: 35,000 kg, empty load weight: 6,537 kg, maximum load weight: 28,463 kg, axle configuration: 3 axles, first registration: 10/2015, tire size: 385/65 r22.5, machine/vehicle number: bf996c16c980c5f73a19d37b8, Further information Fine-grained steel welded construction in lightweight design, saddle plate with replaceable 2 king pins, outer frame slightly slanted with load-lock profile for attaching tensioning straps Note! To attach the straps in conjunction with drop sides, the drop sides must be opened, 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation, door locks on the side, wheel chocks with holder, pallet box for 32 Euro pallets (long version), ground clearance approx. 300 mm). Note: Free support leg corner dimension or free swing-through radius to the rear approx. 1930 mm, quarter-shell mudguards in front of and behind axle unit, with anti-spray flaps only on last axle, impact protection at rear, pallet stop on both sides approx. 20 - 25 mm high, in bolted version, loading height reduced by approx. 20 - 25 mm BPW disc brake axles with 430 mm disc diameter, air suspension, 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (with starting aid up to max. 25 km/h) 2-line compressed air brake system, spring-loaded parking brake, 2 swap-proof coupling heads at the front, without connecting cable, EBS, electronic braking system with EBS socket at the front, without connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS, with lifting & lowering valve, vehicle stability system 24 volt, multi-chamber lights, amber LED lighting at the side, amber LED lighting at the side with 20 LED diodes per light, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 1 x 15-pin socket at the front, without connecting cable, LED safelight, at the top of the rear corner stanchions, 2 additional LED work lights at the rear, switched via reversing light Floor: Screen printing plates approx. 30 mm thick, cross joints with Omega inlay, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Front bulkhead/front stanchions: 2,480 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, bottom inside at approx. 140 mm height with steel impact protection Cob Hn Hekyrmieumsgt Middle stanchions: 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and long pocket at the bottom, 3 pairs of stanchion positions, aluminum insertion slats Rear steel corner stanchions up to lower edge of roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors (heavy dents), 2-leaf with 2 internal espagnolette locks each Tarpaulin with welded-in horizontal and vertical straps, stainless steel tensioning fasteners, customer lettering on side tarpaulins and rear portal, as digital print Roof: Sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-shaped roof rail for automotive industry, internal width between the roof rails approx. 2,490 mm, tarpaulin color: white, lifting roof can be raised hydraulically by 400 mm at each corner stanchion using a hand pump. Mobile with raised lifting roof, can be adjusted upwards by 4 x 50 mm. Note overall height! Incl. tarpaulin extension by 200 mm, only in conjunction with tarpaulin. Approval country: Germany, test approval according to EC 2007/46, load securing certificate according to EN 12642 XL (only valid in combination with 4 rows of aluminum slats), additional beverage c

Condition: used, overall weight: 38,000 kg, empty load weight: 4,880 kg, maximum load weight: 33,120 kg, axle configuration: 3 axles, first registration: 06/2019, tire size: 385/55 r22.5, machine/vehicle number: 6ae9911fbe29b1075c37a723d, Further information Fine-grained steel welded construction, fifth wheel plate with interchangeable 2 kingpins and 2 kingpin positions Container mountings:Rear extension retracted: 1 x 20 foot flush rear, low fifth wheel loadRear extension extended: 2 x 20 feet or 1 x 40 feet with gooseneck tunnel, front cross member with folding locks (not available for front extension), without rear height adjustment and without folding center supports, no transport of containers without tunnel possible, front container guide pluggable and removable (electrics, air and brake connections at the front of the front cross member), rear extension mounted on rollers, with hand crank, 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation, wheel chocks with holder, aluminium side collision protection, galvanized steel underride guard, half-shell mudguards with anti-spray flaps in accordance with EC, rear impact protection SAF disc brake axles, with 430 mm disc diameter, axle/chassis laser-measured to reduce tire wear and fuel consumption, hub odometer/kilometre counter, axle spacing offset mm (combined transport) up to 44 t gross train weight, air suspension, 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) 2-line compressed air brake systemColor-coded cable routing for easy servicing, spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting cable, EBS, electronic braking system with EBS socket at the front, without connecting cable, Attention: The trailer vehicle may only be towed by towing vehicles that guarantee the effectiveness of the ABS, with lifting & lowering valve, vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Cgjb Hnjkyrmqj Humet 24 volt, multi-chamber lights, rear and brake lights in LED, amber LED lighting at the sides, 2 white position lights at the front, 2 white/red lane departure warning lights at the rear, 2 x 7-pin and 1 x 15-pin interchangeable, sockets at the front, without connecting cable Country of registration: Germany, test approval according to EC 2007/46, 24/7 service hotline, incl. loading to 2/3 stack, loading racks against deposit, prepared for license plate holder single-line, warning sign according to ECE - 70, ADR warning sign at the rear, foldable, contour marking with reflective strips according to ECE R 048, white at the sides and red at the rear

Condition: new, overall weight: 21 kg, empty load weight: 6 kg, maximum load weight: 14 kg, axle configuration: 1 axle, tire size: 235 / 75 r 17,5, machine/vehicle number: df0bcd99c5751964e020b1055, Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with replaceable 2 kingpins, low bed from wheel area to gooseneck sloping to approx. 210 mm loading height, rear sloping to wheel area, suspension bar for aluminum ramps at the rear across the entire width Wheel chocks with holder Aluminum side bumpers Wheel cover with galvanized sheet steel, removable 1 towing eye at the rear, 10 to. Spare wheel with holder on front wall/stowage box outside front Steel storage box on gooseneck at the front, transverse, approx.: L = 2400 mm, W = 400 mm, H = 600 mm, lockable Electric cable winch, 24 volt, pulling force 8165 kg, mounted at the front on gooseneck behind the stowage box on loading area, operation with radio remote control, cable length 35 m x approx. 10 mm, with roller cable window and 2 removable guide rollers on gooseneck and rear flange. Nato socket on connection plate 1 pair of wheel recesses approx. 700 mm after the gooseneck, starting in the floor recess, open to the outside. Note: Main frame protrudes approx. 145 mm.4 pairs of plug-in positions for wheel stops (Fliegl standard), without wheel stops for parking the semi-trailer approx. 100 mm high and approx. 100 mm long Piece of plug-in wheel stops When transporting SZM, an approx. 50 mm shim is placed in the front wheel wells approx. 50 mm high, approx. 1200 mm long, approx. 500 mm wide Low loader lashing eyes 2 pairs of 2.5 to lashing eyes on gooseneck7 pairs of lashing mushrooms embedded in the top and sides of the outer frame, 10 to each 4 pairs of 10 to lashing eyes embedded in the top of the main frame side member1 screw lashing eye with 6.7 to each (JDT) at the rear in the middle of the ramp storage compartment1 additional folding lashing eye at the front of the drop deck, 10 to each Axle + suspension SAF drum brake axle, Air suspension with lifting & lowering valve Wheels and tires 235 / 75 R 17,5 from leading manufacturers Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights in LED with resistor, amber LED lighting on the side, license plate lighting in LED, (Note! with certain towing vehicles, misdiagnoses may occur although the function is given) 2 white front position lights in LED 2 white/red rear lane departure lights in LED 2 x 7-pin and 1 x 15-pin interchangeable front sockets, without connecting cable LED rotating beacon with holder, switched via parking light (light can be removed) Additional LED work light(s) at the rear, switched via reversing light Floor Gooseneck with steel / checker plate covering Deep loading area perforated steel plate, steel / checker plate covering in the wheel recess area and removable sheet metal covering in the wheel housing area Rear slope with perforated steel plate Drop sides Aluminum, 400 mm high, laterally on gooseneck, pluggable, approx. 2500 mm long Rear wall aluminum, 400 mm high, on gooseneck, pluggable Drive-on ramps Pair of aluminum loading ramps max. load capacity 12,000 kg per pair, length approx. 3400 mm and width approx. 320 mm, storage compartment for ramps 1 x between the longitudinal beams at the rear Cgeb Hn Huji Ri Hkjmot Operating instr

Condition: new, overall weight: 24 kg, empty load weight: 3 kg, maximum load weight: 20 kg, axle configuration: 3 axles, tire size: 385/55 r22,5, machine/vehicle number: c3dd8c834afed73501f8074af, Further information Chassis Changing turntable Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 Turntable with strong ball bearing slewing ring 2 wheel chocks with holder Aluminum side bumper Steel underride guard Front half-shell mudguards and rear half-shell mudguards 2 stainless steel storage box, w=600/h=400/t=500 mm, with polished door, lockable 1 pair of warning signs, double LED illuminated, extendable to 3,000 mm at the rear, rear only 1 preparation plug for retrofitting warning signs at the front for customers Towing equipment Trailer turntable Drawbar with tested 40 mm towing eye Drawbar mechanically adjustable in length by 6 x 100 mm and lockable (drawbar length approx. 1,900 - 2,500 mm) Drawbar height adjustment via spring Axles + suspension BPW disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension with lift & lower valve Wheels and tires 385/55 R22,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Spring-loaded parking brake 2 interchangeable clutch heads at the front, with connecting cables to the motor vehicle, EBS, electronic brake system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear Removable rotating beacon 1 additional LED work light(s) at the rear, switched via reversing light 2 LED work lights on both sides (1x left, 1x right) (switched via reversing light) 1 x 15-pin plug at the front, with connecting cable, Country of registration / plates Country of registration: Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Csboi Riyls Hn Humegt Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar KTL black

Condition: new, overall weight: 14 kg, empty load weight: 3 kg, maximum load weight: 11 kg, axle configuration: 2 axles, tire size: 235/75 r17,5, machine/vehicle number: 207ad28f83705ed0d38a4f174, Further information Chassis Wechel central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear Cob Hn Huoi Ri Iajmjgt 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 flush with rear (for 7.15 swap bodies not flush with rear, forklift pockets/frame protrude) Telescopic front support leg 1 pair of front gear support legs, with straight lower section and single-sided operation in FR right Wheel chocks with holder Aluminum side bumpers Steel underride guard Half-shell mudguards Bracket for truck-mounted forklift at the rear, including 2 fork pockets, 2 extendable support tubes, bracket for chain safety device with pin. Underride guard with light unit can be folded away. Including 2 loose rubbers to protect the rear wall, we recommend counterweight! Partially low ground clearance with forklift, poor tracking behavior possible, without warranty! (Forklift tare weight up to max. 1500 kg for trailers). (With proximity switch for forklift control in conjunction with lift axle)The axles are shifted to the rear by the forklift bracket, observe load distribution when driving without forklift. Customer risk! (For swap body trailers, driving with a forklift is only permitted in conjunction with a swap body) Forklift bracket as AU 203670 adapted to 7.45 m swap bodies Counterweight at the front between the frames, approx. 300 kg, if necessary, exact check still required Towing device central axle trailer Tow bar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or exact testing still required if ordered) Lower coupler drawbar without length adjustment drawbar Axles + suspension SAF drum brake axles of the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-applied parking brake Duomatic connection at the front, with connection line to the engine trolley, in FR-left Duomatic connection at the front, with connection line to the motor vehicle, connection in FR-right EBS, electronic brake system with EBS plug at the front, with connecting cable, in FR-left Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in each case in lowering / lifting position Vehicle - driving stability system Wheels and tires 235/75 R17.5 tires of the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 volt, 4 x 3 chamber lights + 1 round reversing light and + 1 round rear fog light, amber LED lighting on the side, lights mounted in a protected position! 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin plug at the front, with connecting cable, in FR-left 2 x 7-pin sockets in FR left rear for truck-mounted forklift 1 x 15-pin socket in FR left rear for truck-mounted forklift LED work lights on both sides behind the 2nd axle (switched via reversing light) Additional LED work light(s) at the rear, switched via reversing light Approval / plates Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame

Condition: used, overall weight: 18,000 kg, empty load weight: 2,872 kg, maximum load weight: 15,128 kg, axle configuration: 2 axles, first registration: 11/2019, tire size: 385/65 r22,5, Year of construction: 2019, machine/vehicle number: 3ca51192c90a3f38a59d77748, Further information Welded fine-grained steel construction, front stop, longitudinally adjustable and foldable, removable pair of guide rollers, front and rear, Swap Guard - swap body guide, in front of and behind each container lock, 4 container locks with sturdy outriggers on 20-base for swap bodies 7.15 and 7.45, turntable with strong ball bearing slewing ring, wheel chocks with holder, Aluminum side collision protection, side collision protection set inwards for optimum clearance to the swap body supports, steel underride guard, underride guard shortened for optimum clearance to the swap body supports, lighting system mounted in a protected position, quarter-shell mudguards at the front and half-shell mudguards at the rear, without impact protection, spare wheel holder in basket design, plastic toolbox Drawbar (L = 2,200 mm) with tested 40 mm drawbar eye, drawbar length, drawbar height adjustment via spring Csb Hn Hji Ri Dzoumjgt SAF disc brake axles with 430 mm disc diameter, axle/chassis laser-measured Reduction in tire wear and fuel consumption, air suspension 2-line compressed air brake systemColored line routing for easy servicing, air supply 208 liters, spring-loaded parking brake, 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, EBS, electronic brake system with EBS plug at the front, with connecting cable, )Attention: The trailer vehicle may only be towed by towing vehicles that guarantee the effectiveness of the ABS!) with lifting & lowering valve, holding function in lowering / lifting position, brake release function via button on the vehicle next to H & S valve, for releasing the brake when coupled, EBS power supply must be guaranteed! 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 1 x 15-pin plug at the front, with connecting cable, additional LED work light(s) at the rear, switched via reversing light, LED work light at the front centered between the beams, shining to the rear, switched via reversing light Country of registration: Germany, with Dekra approval and certificate (according to §13 EG - FGV), prepared for single-line license plate holder, warning sign according to ECE - 70, ADR warning sign at the rear, hinged, contour marking with reflective strips according to ECE R 048, white at the sides and red at the rear

Condition: new, overall weight: 18,000 kg, empty load weight: 3,055 kg, maximum load weight: 14,945 kg, axle configuration: 2 axles, tire size: 235/75 r17,5, machine/vehicle number: 06017a31026c05fc8f6ccf5ae, Further information Chassis Changing turntable Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 Turntable with sturdy ball bearing slewing ring 2 wheel chocks with holder Aluminum side bumper Steel underride guard Quarter-shell mudguards at the front and half-shell mudguards at the rear Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the motor vehicle, EBS, electronic braking system with EBS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in both lowering and lifting position Wheels and tires 235/75 R17.5 tires of the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights in LED with resistor, amber LED lighting at the side, license plate lighting in LED, (Note! with certain towing vehicles, misdiagnosis may occur although the function is given) 2 white front position lights in LED 2 white/red rear lane departure lights in LED 1 x 15-pin plug at the front, with connecting cable, Additional LED work light(s) at the rear, switched via reversing light Csb Hn Husi Ri Rcemegt Approval / plates Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Attention: Archive pictures!

Condition: new, overall weight: 13,400 kg, empty load weight: 2,100 kg, maximum load weight: 11,300 kg, axle configuration: 2 axles, tire size: 275/70 r 22,5, machine/vehicle number: 8fbda13da8c595f64678f0f82, Further information Chassis central axle trailer Fine-grained steel welded construction Fifth wheel coupling, make of our choice for 2 kingpins. with ball bearing slewing ring, max. 20° stop Support on drawbar and dolly at the front Wheel chocks with holder Steel underride guard Half-shell mudguards Towing device central axle trailer CLG under-coupler drawbar with tested 50 mm towing eyes to the dolly and to the motor vehicle, including drawbar lock on the truck! Axles + suspension BPW disc brake axles Air suspension for Swap Train version Standard Saddle height lowered approx. 1100 mm, saddle height raised approx. 1280 mm, saddle height approx. 1140 mm, Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the motorized trolley, 2 non-interchangeable coupling heads with Wendelflex connecting lines to the trailer EBS, electronic brake system with EBS plug at the front, with connecting cable, EBS Wendelflex connecting lines to the trailer Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering, ECAS, via truck control, Ecas CAN 2 bus required in the truckwithout Ecas CAN 2 bus in the truck, additional operating control required in the truck (not included in the scope of delivery):Electrical system with a pre-assigned cable and a distributor box. Operation with 15-pin socket pin 11 and 15 with 2 x 7-pin socket pin 7 and 5 Note! This version must still be technically tested in conjunction with the trailer, it is likely that the dolly and the trailer can only be raised and lowered together if this is not technically possible, operation is via WABCO eTASC with hold function in lowered position + auto-reset function (no power required from the truck). Additional operation on the vehicle via WABCO eTASC + hold function in lowering position + auto-reset function (no power required from the truck) Vehicle - driving stability system ECAS only possible in conjunction with WABCO EBS. Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Brake release function from truck (via button) on PIN 14 and additionally via button on vehicle next to H & S valve, for releasing the brake when coupled, EBS power supply must be guaranteed! with Can Router Wheels and tires 275/70 R 22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side Side amber LED lighting coupled with the blinker Flashing side lights Csb Hn Hei Rizxoumogt 2 white LED position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 2 x 7-pin non-interchangeable plugs with helical flex connection cables to the trailer Cable + plug and/or socket for reversing camera system, depending on vehicle type Operating instructions Note! Please note the currently permitted route network! Towing vehicle must be taken to the Triptis factory for approx. 1 week for adjustment of the towing bar! Please note the CLG recommendation as per the appendixThe following is required before acceptance of the order: Submission of all relevant measurements and dimensions as per the Fliegl CLG form (see appendix) The coupling height of the planned trailer must be

Condition: new, overall weight: 11,800 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: ebf3f771e96394cd89e56bbb7, Further information Chassis central axle trailer Welded fine-grained steel construction 6 pairs of lashing eyes bolted to the outside of the floor/outer frame, 5 tons each 2 pairs of lashing eyes additionally bolted to the floor, 5 tons each in the corners Gear support foot at the front Folding rear support 2 wheel chocks with holder Steel underride guard Rear spray flaps across the entire width Quarter-shell mudguards 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Towing device central axle trailer Towing bar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension Drum brake axles, manufacturer's choice Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Floor Steel/ checker plate floor for high point load capacity Note: Slight floor corrugation possible due to welding distortion! Platform length approx. 5,200 mm Rear sloping to approx. 900 mm Front wall / front corner stanchions 25 mm aluminum hollow profile, 400 mm high, Drop sides 25 mm aluminum hollow profile, 400 mm high, foldable and removable Cgob Hn Huji Rixromot Rear wall / rear corner stanchions 1 pair of steel stanchions attached to the frame and with bracket for locking the drive-on ramps, drive-in width approx. 2,430 mm Drive-on ramps 2 steel ramps 2,300 mm long, 510 mm wide, can be moved sidewayswith grab handle on the ramps covered with 3 toothed steel rails With gas pressure jack for one-man operation Country of registration/plates Country of registration: Germany 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Front wall aluminum Side wall anodized aluminium Drive-on ramps Hot-dip galvanized Attention! These are archive pictures.

Condition: new, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: 408ba9a39bbb8087056d6e563, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3,000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° / D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Cjb Hn Hoi Ri Daeumogt Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel housing area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of approval / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized

Condition: new, empty load weight: 24,000 kg, maximum load weight: 7,550 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: ede0610378cbe39cc4883251d, Further information Chassis low loader trailer Welded steel construction 1st pair of wheel recesses after steel platform recessed in the tramline area, inclined towards the entrance, length at the bottom approx. 1400 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. If machines are to be driven where the overall height is to be checked, we request a technical data sheet for the machine types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses may be required by the customer). Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Cgsb Hn Huoi Ri Rysmst Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 110 3 pairs of lashing points, 10 tons each, integrated in the floor at the front Incl. 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x to neck area remaining distributed in between Distance not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles which guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Twin steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, incl. Afterwards with 70 mm softwood floor, steel/checker plate covering in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. cannot be achieved. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany Incl. with

Condition: used, overall weight: 35,000 kg, empty load weight: 6,927 kg, maximum load weight: 28,073 kg, axle configuration: 3 axles, first registration: 07/2016, tire size: 385/55 r19,5, machine/vehicle number: 5a722b71e07e463c6c5370ad2, Further information Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Note! With a frame neck height of 30 mm, the truck wheelbase must not exceed 3700 mm! Outer frame slightly slanted with Load-Lock profile for attaching lashing strapsNote! To attach the straps in conjunction with drop sides, the drop sides must be opened! Not in the neck area! 10 pairs of additional lashing eyes embedded in the outer frame, 2.5 tons each, outer frame with Load-Lock profile for attaching lashing strapsNote! Cannot be used with drop sides! 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation, folding supports at the front in front of the bulkhead can be extended outwards and folded down. Moved inwards as far as possible when driving. (for unhitching under load), without supports, pull-out ladder at the rear, door locks at the side, wheel chocks with holder, aluminium side collision protection, galvanized steel underride guard, quarter-shell mudguards in front of the first axle and behind each axle, with anti-spray flaps behind each axle, rear impact protection Heavy blocker rear transverse impact protection, heavy-duty pallet stop on both sides, approx. 20-25 mm high, with lashing option every 200 mm, loading height reduced by approx. 20-25 mm, plastic toolbox SAF disc brake axles, air suspension, without lift axle 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable front coupling heads, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, vehicle stability system 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front 2 white/red lane departure warning lights at the rear, 2 x 7-pin and 1 x 15-pin interchangeable sockets at the front, without connecting cable Cgsb Hokyrlwsn Humet Floor: Front area steel floor with anti-slip coating, screen printing plates approx. 30 mm thick, cross joints with Omega inlay, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg, steel/ checker plate covering in the wheel area. Front bulkhead/front stanchions: 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, bottom inside at approx. 140 mm height with steel impact protection Middle stanchions: 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and long pocket at the bottom, 3 pairs of stanchion positions, aluminum insertion slats Rear steel corner stanchions up to lower edge of roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin with welded-in horizontal and vertical straps, stainless steel tensioning fasteners, customer lettering on rear portal Roof: sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-roof rail for automotive industry, internal width between the roof rails approx. 2,490 mm, tarpaulin color: white, EcoLift - lifting roof can be raised by approx. 380 mm, with gas pressure damper support, anti-ice system, with a hose in the middle, with automatic ventilation Approval country: Germany, test approval according to EC 2007/46, load securing certif