Used Fliegl Semitrailers for sale (300)

Condition: new, overall weight: 18 kg, empty load weight: 4 kg, maximum load weight: 13,880 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: 8df1ead53cc82aeb51e50a37d, Further information Chassis Turntable Disposal Fine-grained steel welded construction Container locking system: - 2 pairs of locking hooks embedded in the floor - Pneumatic actuation The container locking mechanism is a 2-point design, acting from the inside, and locking of roll-off containers with an inner web is not possible (for transporting roll-off containers with a sub-frame in accordance with DIN 30722) Cslnsi Ri Nuj Thhgegt Note! At the start of the roller recess at the front, the container must be pushed on completely flat! Longitudinal guide rails can be moved sideways and removed, rails approx. 115 mm high Turntable with strong ball bearing slewing ring 8 pairs of lashing mushrooms at the top and sides of the outer frame, 5 tons each 7 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) 2 wheel chocks with holder Aluminum side bumpers Steel underride guard Quarter-shell mudguards according to EG with anti-spray flaps according to EG Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Steel floor Roller recess for container recessed in the floor at the frontfor roll-off containers from 5,000 - 7,000 mm in length Note: Slight floor undulation possible due to welding distortion! Drive-on ramps Lockable storage space for loading ramps underneath the loading area Operating instructions A special permit is required for axle loads of 10,000 kg. Approval must be applied for individually in each federal state; the legislator does not have to grant approval for 20 t GG. Customer risk. The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paint finish Frame DB 7350 nova gray 15-year warranty against rusting through Note: Bottom corrugation possible due to hot-dip galvanizing! Drawbar KTL black Attention: Archive pictures!

Condition: used, overall weight: 35,000 kg, empty load weight: 7,950 kg, axle configuration: 3 axles, wheelbase: 1,310 mm, loading space length: 13,500 mm, loading space width: 2,470 mm, loading space height: 2,850 mm, loading space volume: 95 m³, first registration: 01/2013, color: black, tire size: 385/55 R22,5, Equipment: ABS, Disc brake EBS Payload 27,050 kg Air-lift suspension Roll-up tarpaulin Platform SAF axles Coln Tjuiyvyohhgegt Alcoa aluminum rims Lifting and lowering device Lashing rings Errors excepted

Condition: used, Functionality: fully functional, overall weight: 18,000 kg, empty load weight: 3,250 kg, maximum load weight: 14,750 kg, axle configuration: 2 axles, first registration: 10/2018, next inspection (TÜV): 04/2025, tire size: 445/45 R19,5, Year of construction: 2018, machine/vehicle number: WFDFLT21801008256, Equipment: ABS, German papers, good condition Tandem central axle trailer, short coupling system fully galvanized for bridges up to 7.80 m Cgoln Thot U Nfpshgot parking height 1020 to 1320 lifting h. 970-1370 Driving height 1040 SAF central axle unit, EBS 445/45R19.5 tires Payload 14,750 kg Available several times

Condition: new, overall weight: 11 kg, empty load weight: 2 kg, maximum load weight: 9 kg, axle configuration: 2 axles, tire size: -, machine/vehicle number: bdf30cb8a53c70e900bdb40a7, Further information Chassis central axle tipping trailer Welded steel construction, continuous tipping shaft at the rear with 80 mm ball tipping bearing Gearbox support foot at the front 2 wheel chocks with holder Steel underride guard Rear splash guards across the entire width Quarter-shell mudguards Lockable storage space for access ramps underneath the loading area Towing device central axle trailer Tow bar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension BPW drum brake axles Cgjlnji Riwis Thhgst Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Hand spindle parking brake Integral air reservoir ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, with connecting cables to the motor vehicle, Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connecting cable, Hydraulics Three-way tipping mechanism, hydraulic multi-piston press with lift limiter and safety cable, Low-pressure cylinder up to max. 170 bar, without throttle. If necessary, this must be retrofitted to the truck. Hydraulic connection with SVK plug NW 10/3, incl. connection hose Hydraulic actuation via truck power take-off Tilting bridges Sturdy tipper body with 4 mm sheet steel floor, steel side wall structure, continuous side walls, hinged and pivoted with central locking at the bottom. Rear corner stanchions pluggable. Rear wall can be folded down and pivoted, with central locking at the bottom. Platform length approx. 4,500 mm, side walls with 5 hinges at the bottom. Platform width 2420 mm 5 pairs of lashing eyes in the floor, 5 tons each Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Dropside/bridge RAL 3002 carmine red Rear support, access ramps, storage box are optionally available at extra cost Attention: Archive pictures

Condition: used, overall weight: 35,000 kg, empty load weight: 7,950 kg, axle configuration: 3 axles, wheelbase: 1,310 mm, loading space length: 13,500 mm, loading space width: 2,470 mm, loading space height: 2,850 mm, loading space volume: 95 m³, first registration: 03/2013, color: black, tire size: 385/55 R22,5, Equipment: ABS, Disc brake EBS Payload 27,050 kg Air-lift suspension Roll-up tarpaulin Platform SAF axles Alcoa aluminum rims Lifting and lowering device Cgjln Thheuiytlsgjt Lashing rings Errors excepted

Condition: new, overall weight: 39,000 kg, empty load weight: 3,200 kg, maximum load weight: 35,800 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, machine/vehicle number: f80f2330e1318ef03bc20755e, Further information Cgjlnsi Riwqj Thhgjt Fine-grained steel welded construction in lightweight design, saddle plate with replaceable 2 kingpins, only 2 longitudinal beams as double T-beams for retrofitting connecting gallows at the front in new/current design, outer frame slightly slanted with load-lock profile for attaching tension beltsNote! to attach the belts in conjunction with drop sides, the drop sides must be opened! 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation, wheel chocks with holder, aluminium side bumper, foldable, galvanized steel underride guard, extendable, half-shell mudguards!!! enclosed loose, not mounted!!!, with anti-spray flaps behind each axle, 1 plastic water barrel, capacity approx. 30l, in FR left BPW disc brake axles with 430 mm disc diameter, axle/chassis laser-measured Reduction of tire wear and fuel consumption, air suspension, 1st axle automatic lift axle, can also be lowered manually, can be operated with a hand button on the vehicle 2-line compressed air brake system, with 1 air reservoir central standard, spring-loaded parking brake, 2 interchangeable coupling heads at the front, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, EBS 2S/2M, test connection for brake cylinder pressure on the EBS module laid to the outside, Attention: The trailer vehicle may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, control unit + brake integrated in frame as with tipper semi-trailer, mounted in front of the axles Brake pad wear indicator for disc brakes via ABS/EBS lamp Truck 385/65 R22.5 Continental tires, steel rims, factory silver 24 volt, multi-chamber lights, amber LED lighting at the side as for tipper semi-trailer, dimension 3000 mm must be observed, 2 white LED position lights at the front, loose, 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable sockets at the front, without connecting cable Germany, test approval according to EC 2007/46 for complete vehicle, 24/7 service hotline, prepared for double license plate holder single-line1 x plastic and 1 x stainless steel interchangeable holder Warning sign according to ECE - 70, aluminum, loose, EBS, safe parking, without contour marking / reflective strips according to ECE R 048, Frame: DB 7350 nova gray, support legs: black coated Available immediately!

Condition: new, overall weight: 38 kg, empty load weight: 3 kg, maximum load weight: 34 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, machine/vehicle number: 1f4581c873ed977cb9602039b, Further information Chassis semi-trailer container Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Container mounts: 1 x 20 foot centered (or swap body container 7.15 / 7.45), not retractable at the front, the pivot pins of the container lock in the longer version 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Cgeln Tei Rixkjhhgst 2 wheel chocks with holder Side collision protection Aluminum underride guard Half-shell mudguards with anti-spray flaps according to EG VA drip tray with 1 1/4 inch drain pipe + 1 1/4 inch stopcock, incl. drip tray, with perforated tread plates, approx. 400 mm wide, left + right between drip tray and side member 4 hose trays approx. 4500 mm long (hose box) for hose pipes 2 x DN 200 outside + 2 x DN 160 centrally arranged, rear hose box (stainless steel) 300 mm deep, splash-proof, cover (stainless steel) with rubber seal all round, with drain hole at lowest point, then without cover on hose pipes 1 stainless steel earthing lug at the rear in FR on the right of the frame, with international earthing sticker on the frame, Steps at the rear right on the underride guard, at the rear in FR right on the outside of the main beam, tread plate approx. 260 mm long and 300 mm wide, Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake system Colored cable routing for easy servicing Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/65 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin socket at the front, without connecting cable Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) This vehicle may only be loaded with 20' tank containers that comply with ISO 668 and in particular ISO 1496-3! The tank containers must have "end-load-transfer areas"! Country of approval / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Approval according to ADR acc. to 9.1.1.2 of ADR, EX/II, EX/III / certificate of approval for vehicles for the transport of certain dangerous goods (ex.B3) with warning sign at the rear, not valid for substances according to UN 0331 and 0332 (explosives B-E) Contour marking with refle

Condition: new, overall weight: 35,000 kg, empty load weight: 5,300 kg, maximum load weight: 29,700 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, machine/vehicle number: 7383bc2b7f580f0cb319b52f7, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Surface stone-repellent Splash guard behind last axle in asphalt version, attached to mudguard with hinge, with attachment option on top of mudguard, shortened mudguard Tow hook at the rear Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics High-pressure cylinder max. 250 bar, with HDK screw socket, fixed part, NW 48 mm (without hose connection) Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Membrane rear wall Rear wall as pendulum flap, resting on the outside with 2-fold hook locking. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Insulated body, Fliegl Asphalt Profi Thermo, body insulated at the front, sides, bottom and rear with Fliegl Isotherm. BASIC cover, tarpaulin cladding Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) Body strength according to EN 12642 24/7 service hotline Manufacturer certificate for thermal vehicles according to RS 10 - 2013 Prepared for single-line license plate holder Celsi Rix Ion Thhgsgt Contour marking

Condition: new, overall weight: 35,000 kg, empty load weight: 5,600 kg, maximum load weight: 29,400 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, machine/vehicle number: 824d4741dc933a94e9a7a7a8c, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Surface stone-repellent Splash guard behind last axle in asphalt version, attached to mudguard with hinge, with attachment option on top of mudguard, shortened mudguard Tow hook at the rear Axles + suspension Cgjln Thhei Rix Soget SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics High-pressure cylinder max. 250 bar, with HDK screw socket, fixed part, NW 48 mm (without hose connection) Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Membrane rear wall Rear wall as pendulum flap, resting on the outside with 2-fold hook locking. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Insulated body, Fliegl Asphalt Profi Thermo, body insulated at the front, sides, bottom and rear with Fliegl Isotherm. BASIC cover, tarpaulin cladding Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) Body strength according to EN 12642 24/7 service hotline Manufacturer certificate for thermal vehicles according to RS 10 - 2013 Prepared for single-line license plate holder Contour marker

Condition: new, overall weight: 32,000 kg, empty load weight: 4,400 kg, maximum load weight: 27,600 kg, axle configuration: 2 axles, tire size: 385/65 r22,5², machine/vehicle number: 113bec9dd54d24fa34a088424, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Cgoln Toi Riziohhgst Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10 J

Condition: new, overall weight: 29 kg, empty load weight: 5 kg, maximum load weight: 22 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: e7fbe178b85a202cade7e95af, Further information Chassis saddle forwarding Welded fine-grained steel construction, saddle plate with replaceable 2 king pins, with 2 king pin positions Slightly angled outer frame with load-lock profile for attaching lashing strapsNote! To attach the straps in conjunction with drop sides, the drop sides must be opened! 2 pairs of lashing eyes embedded in the outer frame on gooseneck, 5 tons each 8 pairs of lashing eyes embedded in the outer frame in the low bed, 5 tons each 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminum side bumper Steel underride guard Quarter-shell mudguards in front of and behind axle unit 2 Stainless steel stowage box, w=600/h=400/t=500 mm, with polished door, lockable 2 pairs of stake pockets recessed in the outer frame on gooseneck, 70 x 40 mm internal dimensions 6 pairs of stanchion pockets in the outer frame recessed in the deep bed, 70 x 40 mm Internal dimension!!! Internal width between the stanchions 2420 mm!!! 3 lashing/stanchion rails in the drop-down bed, embedded transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer stanchions approx. 2170 mm), approx. 100 mm high. With 20 mm round steel slats, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). For lashing and inserting stanchions 80 x 80 mm. Piece of stanchions W=80/ D=50/ L=1200 mm, hot-dip galvanized Piece of stanchions W=80/ D=80/ L=1200 mm, hot-dip galvanized Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them. Mechanical rear extension with hand crank, can be extended by approx. 1,500 mm, can be locked every 500 mm, with support beam, can be loaded with 2000 kg over the entire width at the load center of gravity at approx. 500 mm, can be loaded with 1000 kg over the entire width at 1000 mm and can be loaded with 500 kg over the entire width at 1500 mm, incl. extendable underride guard with lighting, 2 pairs of stanchions W=80/ D=80/ L=1200 mm, hot-dip galvanized Open storage compartment for stanchions, on the front wall or underneath the loading area (for 10 stanchions 80 x 50 x 1200 mm and 4 stanchions 80 x 80 x 1200 mm) Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption last axle self-steering, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lift & lower valve Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales). Electrical system Csln Thhoi Ri Hvsgsgt 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin sockets at the front, without connecting cable 2 additional LED work lights, at the rear, switched via reversing light 1

Condition: new, overall weight: 35 kg, empty load weight: 5 kg, maximum load weight: 29,045 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, machine/vehicle number: d9c951d746f03c05bc5470f89, Further information Chassis saddle forwarding Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Vario stanchion system 4 pairs embedded in loading area, can be pushed together to 2 100 mm and extended to approx. 3 500 mm for loading. Stanchions can be locked every 100 mm on an internal width of 2 100 mm to 3 000 mm, 4 pairs of divisible stanchions 600 mm + 1 200 mm, total height 1 800 mm removable. With an internal stanchion width from approx. 2 350 mm, excess width. Vario end walls Floor prepared for inserting 3 end walls. 4 x 5 pairs of Vario stanchion pockets for insertable end walls (front and rear) and 1 x 3 pairs in the middle for transporting 2 x 5,000 mm or 2 x 6,000 mm construction steel mats. 2 Vario end walls, each consisting of 1 pair of plug-in stanchions and 1 top crossbeam approx. 2200 mm wide. Cross beams can be extended by 220 mm on both sides, with lashing hole for tensioning. 1900 mm high Vario bulkhead, can be converted to 1300 mm or 700 mm high. 4 stanchion pockets embedded in the center of the floor for 80 x 80 mm stanchions Colei Ri R Den Thhgogt 1 pair of supports at the bottom for Vario bulkhead at the front 1 pair of lower supports for rear Vario bulkhead Slightly slanted outer frame with Load-Lock profile for lashing strap attachment 14 pairs of lashing eyes additionally embedded in the outer frame, 5 tons each 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Extension ladder at the rear Wheel chocks with holder Aluminium side collision protection Galvanized steel underride guard Quarter-shell mudguards in front of and behind axle unit with anti-spray flaps on last axle only Impact protection at the rear 8 construction steel winches with wire rope and counter hooks, 4 x left and 4 x right with rope feed-through through the outer frame, 1 removable slip-on gearbox for construction steel winches - supplied loose (without bracket on the frame) 1 spare wheel holder for 1 e-wheel, with wheel fastening set 1 plastic toolbox, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) 1 closed stanchion stowage box, open at the top, below loading area, doors on both sides, w=450 mm/h=400/420 mm/d=2460 mm 4 lashing/stanchion rails embedded transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer stanchions approx. 2170 mm), approx. 100 mm high. With 20 mm round steel slats, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). For lashing and inserting stanchions 80 x 80 mm. Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them. Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle lift below the recomm. Driving height, therefore no warranty for tire damage Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be to

Condition: new, overall weight: 18 kg, empty load weight: 3 kg, maximum load weight: 14 kg, axle configuration: 2 axles, tire size: 235/75 r17,5``, machine/vehicle number: 81b04fd2e28f354df79a4c3b3, Further information Chassis Wechel central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear Folding locking adapter + height adjustment for parking height 1,000 - 1,120 mm, center supports can be folded and guide rollers can be pushed upwards, 4 container locking devices with sturdy outriggers on 20-basefor swap bodies 7.15 / 7.45 and 7.82 1 pair of gear support legs at the front, with straight lower section and single-sided operation in FR right 2 wheel chocks with holder Aluminum side bumpers Steel underride guard Half-shell mudguards Towing device central axle trailer Towbar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or exact testing still required in case of order) Under-coupler drawbar, free drawbar length approx. 2200 mm Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the engine trolley, connection in FR-right EBS, electronic brake system with EBS plug at the front, with connecting cable, connection in FR right-hand side Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in each case in lowering / lifting position Vehicle - driving stability system Wheels and tires 235/75 R17.5`` tires of the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 15-pin plug at the front, with connecting cable, connection in FR right-hand side 2 additional LED work lights at the rear, switched via reversing light 1 LED work light at the front, centered between the carriers, radiating to the rear, switched via reversing light Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Cgjln Thji Riy Njhgot Attention: Archive pictures!

Condition: new, overall weight: 18,000 kg, empty load weight: 2,950 kg, maximum load weight: 15,050 kg, axle configuration: 2 axles, tire size: 445/45 r19,5, machine/vehicle number: ccd5fddabaca94f260d9fe895, Further information Chassis Changing turntable Fine-grained steel welded construction Fliegl V-Stream frame Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 Turntable with strong ball bearing slewing ring 2 wheel chocks with holder Aluminum side bumper Side collision protection set inwards, for optimum clearance to the swap body supports Steel underride guard Underride guard shortened for optimum clearance to the swap body supports, lighting system mounted protected Quarter-shell mudguards at the front and half-shell mudguards at the rear Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake system Colored line routing for easy service. Air supply 208 liters Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the motor vehicle, EBS, electronic brake system with EBS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in both lowering and lifting position Wheels and tires 445/45 R19.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 2 additional LED work lights at the rear, switched via reversing light 1 LED work light at the front, centered between the carriers, radiating to the rear, switched via reversing light Country of registration / plates Germany Celn Thhoi Ri Rkogjgt with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Attention: Archive pictures!

Condition: new, overall weight: 24 kg, empty load weight: 6 kg, maximum load weight: 17 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: f8fb99947a1c19bc4d63549ff, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 7 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion with M&S marking Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Additional ramp safety device hinged at the bottom (to prevent the ramps from slipping sideways, not in conjunction with hydraulic side ramp displacement) Cgoln Toi Riwfjhhgjt covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Coun

Condition: new, overall weight: 24,000 kg, empty load weight: 8,900 kg, maximum load weight: 15,100 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: f79a9f15e7131d57a512793ab, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Widenings extendable to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing rings at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical incl. axle load compensation front and rear Axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Cjln Thei Ri Izohgegt Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Front offset with steel/ checker plate covering Then with 70 mm softwood floor, steel/checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Operating instructions With 10,000 kg axle load, a special permit is required, only indivisible load possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany With Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Incl. Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized

Condition: new, overall weight: 11 kg, empty load weight: 3 kg, maximum load weight: 8 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, machine/vehicle number: 057736dac221bda3fc469966a, Further information Chassis central axle trailer Fine-grained steel welded construction Slightly sloping outer frame with Load-Lock profile for attaching tension beltsNote! To attach the belts in conjunction with drop sides, the drop sides must be opened! Front gear support leg Cgjln Thhoi Ri H Dsget Folding rear support 2 wheel chocks with holder Galvanized steel underride guard Quarter-shell mudguards 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 open storage compartment for stanchions, underneath loading area 4 pairs of stanchion pockets embedded in the outer frame, 83 x 83 mm internal dimensions 4 stake pockets centrally recessed in the floor, with reinforcements to the main frame, 83 x 83 mm internal dimensions 6 pairs of stanchions W=80/ D=80/ L=2000 mm, hot-dip galvanized Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them. Tandem trailer drawbar Drawbar with tested 40 mm drawbar eye Drawbar mechanically adjustable in length by 4 x 500 mm from 1800 - 3800 mm, drawbar length set to 1800 mm, (Note! Observe load distribution and drawbar load) Axles + suspension GFA axles with angular roller bearings and S-cam brake Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Floor Screen printing plates approx. 30 mm thick, for high point load capacity Note: Floor warping due to weather influences possible! Platform length approx. 6,200 mm Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. Approval / plates Country of registration: Germany With Dekra approval and expert opinion 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Attention: Archive pictures!

Condition: used, overall weight: 31,000 kg, empty load weight: 5,980 kg, maximum load weight: 25,020 kg, axle configuration: 2 axles, first registration: 09/2019, tire size: 435/50 r19,5 164 j, machine/vehicle number: 41a47569b210fb6ff75f23f78, Further information Welded fine-grained steel construction, fifth wheel plate with replaceable 2 king pins, PRO SLIDE, additional front skid plate for protection when coupling, outer frame slightly inclined with Load-Lock profile for attaching lashing straps, note! to attach the straps in conjunction with drop sides, the drop sides must be opened! 24 t. 2-speed support winch, single-sided operation, with semicircular lower section and straight connecting plate, with thrust compensation, 1 pair of gear support legs at the rear, with straight lower section and single-sided operation in FR right Pull-out ladder at the rear, door brakes on the side, wheel chocks with holder, aluminium side collision protection, galvanized steel underride guard, quarter-shell mudguards in front of and behind each axle, with anti-spray flaps behind each axle, impact protection at the rear, heavy-duty pallet stop on both sides, approx. 15-20 mm high, with lashing option every 200 mm, loading height reduced by approx. 15-20 mm, plastic toolbox, document box, 36x26x4 cm BPW disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption, axle spacing 1810 mm (then 10to axle load technical) Air suspension, without lift axle 2-line compressed air brake systemColored cable routing for easy servicing, spring-loaded parking brake, 2 interchangeable coupling heads at the front, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, vehicle driving stability system, axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure warning lights at the rear, 1 x 15-pin socket at the front, without connecting cable Floor: Screen-printed panels approx. 30 mm thick, cross joints with Omega inlay, on 8 longitudinal beams for high point load capacity for forklift axle load up to max. 7,300 kg and additional reinforcement in the rear area, steel/checker plate flooring in the rear area over a length of approx. 300 mm, flush screen-printed floor. Front bulkhead / stanchions front: 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, crash blocker, bottom inside at approx. 140 mm height with steel impact protection, bulkhead inside additionally covered with 2 x 1250 mm high screen printing plate Center stanchions: 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and a long pocket at the bottom, 3 pairs of stanchion positions Csln Tsk E E H Aehhgjgt Rear wall / rear corner stanchions Rear corner stanchions steel up to lower edge of roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf with 2 internal espagnolette locks each, Fliegl I-Lock integrated door lock awarded with iF Design Award Tarpaulin with welded-in horizontal and vertical straps, Quick Lock system for side tarpaulin with central lock on both sides, Spring Curtain tarpaulin, with high-strength embedded spring steel strips, on both sides Roof: Sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-roof rail for au

Condition: used, overall weight: 18,000 kg, empty load weight: 4,150 kg, maximum load weight: 13,850 kg, axle configuration: 2 axles, first registration: 10/2022, tire size: 235/75 r17,5 zwilling, Year of construction: 2022, machine/vehicle number: e39c5034081b0262ab0e1f028, Further information Fine-grained steel welded construction Container locking system: Celn Tjldhp Dshhgegt - 2 pairs of locking hooks embedded in the floor - Pneumatic actuation The container locking mechanism is a 2-point design that acts from the inside and locking of roll-off containers with an inner web is not possible (for transporting roll-off containers with a base frame in accordance with DIN 30722) Note! At the start of the roller recess at the front, the container must be pushed on completely flat! Longitudinal guide rails can be moved sideways and removed, rails approx. 115 mm high, 2 pairs of adjustable and removable skip locking wedges, 1 pair in front of each container, turntable with strong ball bearing slewing ring 8 pairs of lashing mushrooms recessed into the top and sides of the outer frame, 5 tons each, 7 pairs of stake pockets recessed into the outer frame, inside 70 x 40 mm, 2 wheel chocks with holder, aluminium side bumpers, steel underride guard, quarter-shell mudguards, 1 spare wheel holder for 1 e-wheel, 1 plastic toolbox, container lock, 1 pair of locking cut-outs embedded in the floor at the rear for 1 x 20 foot container, without container locking adapter (additional cross support required at the front and rear of the container, the container must rest evenly across the width in conjunction with the locks, cross supports are not included in the scope of delivery) Drawbar with tested 40 mm drawbar eye, lowerable drawbar with pneumatic lowering & lifting support, in Y-shape SAF drum brake axles, axle/chassis laser-measured Reduction in tire wear and fuel consumption, parabolic suspension with maintenance-free steel/rubber bearings 2-line compressed air brake system, spring-loaded parking brake, 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 additional LED work light(s) at the rear, switched via reversing light Steel floor, roller recess for container recessed in the floor at the frontfor roll-off containers from 5,000 - 7,000 mm long, Note: Slight floor undulation possible due to welding distortion! Lockable storage space for access ramps underneath the loading area Country of registration: Germany, with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline, prepared for single-line license plate holder, contour marking with reflective strips to ECE R 048, white at the sides and red at the rear

Condition: new, axle configuration: 2 axles, first registration: 12/2022, tire size: -, machine/vehicle number: 745183e095a8a43501797c66c, Further information Tandem platform trailer Type TPS 180 Standard building material with forklift bracket Weights and dimensions: Total weight: 18000 kg Unladen weight (basic version) approx.: 4600 kg +/- construction tolerance Payload approx.: 13400 kg Drawbar load: 1000 kg Overall length approx.: 9925 mm Overall width max.: 2550 mm Overall height approx.: 3150 mm Interior length approx.: 7750 mm Interior width approx.: 2480 mm Platform height approx.: 1200 mm Towing height approx.: 380 mm Towbar length approx.: 2150 mm Chassis central axle trailer Fine-grained steel welded construction Outer frame slightly slanted new design with Load-Lock profile for tensioning strap attachment Cgsln Thhondwdhegst 1 pair of gear support legs at the front, with straight lower section and single-sided operation in FR right 2 wheel chocks with holder Aluminum side bumpers Steel underride guard Quarter-shell mudguards 2 plastic toolboxes, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) Bracket for truck-mounted forklift at the rear, including 2 fork pockets, 2 extendable support tubes, bracket for chain safety device with pin. Underride guard with light unit can be folded away. Including 2 loose rubbers to protect the rear wall, we recommend counterweight! Please note! Partially low ground clearance with forklift, poor tracking behavior possible, without warranty! (Forklift tare weight up to max. 1900 kg for trailers). (With proximity switch for forklift control in conjunction with lift axle) The axles are shifted backwards by the forklift bracket, observe load distribution when driving without forklift. Customer risk! Note! Forklift bracket! Carrying a forklift truck can lead to a considerable reduction in the drawbar load. Front counterweight required! On wet and slippery roads, an additional ballast weight provided by the customer or a load of at least 2 tons at the front of the bulkhead is required; the speed must then be reduced and adapted to the roads and driving behavior. The truck must always be secured with chains while driving. The distance between the lift mast and the body must be max. 45 mm or the vertical forklift tines must be in contact with the forklift pockets at the end. We assume that the towing vehicle has no steering or lift axle, or that the steering axle is always locked or the lift axle is always on the ground. Towing equipment for central axle trailers Towing bar with tested 50 mm towing eye, forwarding version (not suitable for trucks with tail lift) Towbar under-coupler Folding bracket with spring support on the drawbar, for guiding the connecting cable to the truck Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension with lift & lower valve 1st axle automatic lift axle with proximity switch, for lift axle (only for driving with forklift) Wheels and tires 385 / 65 R 22,5 according to manufacturer's choice Steel rims factory silver Brake system 2-line compressed air brake system Spring-applied parking brake Vehicle stability system Duomatic connection at the front, with connecting cable to the motor vehicle, connection in FR-right EBS, electronic brake system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, LED multi-chamber lights, amber LED lighting on the side, LED lic

Condition: used, overall weight: 35,000 kg, empty load weight: 6,500 kg, maximum load weight: 28,500 kg, axle configuration: 3 axles, first registration: 02/2020, tire size: 445/45 r19,5, machine/vehicle number: 41b5b53ab0b527fda1f0f26fe, Further information The pictures are archive pictures, the vehicle may still be in use! Chassis saddle forwarding Fine-grained steel welded construction, with preload slight pre-tensioning in the neck area, saddle plate with replaceable 2 kingpins PRO SLIDE, additional front skid plate for protection when saddling up Slightly angled outer frame with Load-Lock profile for attaching tensioning straps Note! To attach the straps in conjunction with drop sides, the drop sides must be opened! 24 to. 2-speed support winch, single-sided operation, with semicircular lower section and straight connecting plate, with thrust compensation Note: Free support leg corner dimension or free swing radius to the rear approx. 1930 mm 1 pair of gear support legs at the rear, with straight lower section and single-sided operation in FR right Pull-out ladder at the rear Side door retainer Wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Quarter-shell mudguards in front of 1st axle and behind each axle With anti-spray flaps behind each axle Heavy blocker rear transverse bumper + side roller bumpers Cgsln Thoqhiyxjhgst Heavy-duty pallet stop bolted on both sides, approx. 15 - 20 mm high, with lashing option every 200 mm, loading height reduced by approx. 15 - 20 mm Plastic tool box, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) Storage compartment for 16 insertable slats, one-sided in FR-left, below loading area Axles+suspension BPW disk brake axles with 370 mm disk diameter, Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Rear loading height approx. 1200 mm when raised (air suspension on truck lowered to approx. 910 mm semi-mounted height) without lift axle Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-applied parking brake Duomatic connection at the front, without connecting cable EBS make Wabco-E, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lift & lower valve + auto-reset function Vehicle stability system Wabco ramp starting aid, TailGUARD with 3 ultrasonic sensors at the rear of the vehicle Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin and 1 x 15-pin interchangeable front sockets, without connecting cable Reversing camera system with color flat screen monitor, with wireless connection to the screen, screen with suction cup mount and power supply via 24 volt vehicle socket Floor Screen printing plates approx. 30 mm thick, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Rear area with heavy-duty floor approx. 1800 mm long In the rear area, steel/ checker plate flooring is fitted over a length of approx. 300 mm (protrudes slightly). Front wall / front corner stanchions 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, Crash blocker, bottom inside at approx. 140 mm height with steel impact protection Center stanchions 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and a long pocket at the bottom. 3 pairs of stanchion positions Insertion slats Wooden slats Additional row of aluminum V-slats Vario steel slats, in conj

Condition: used, overall weight: 26,000 kg, empty load weight: 6,000 kg, maximum load weight: 20,000 kg, axle configuration: 2 axles, first registration: 04/2018, tire size: 205 / 65 r 17,5, machine/vehicle number: 28be789c7675b811b702c6cb3, Further information Welded fine-grained steel construction, saddle plate with replaceable 2 king pins Reinforcer mounting point for gallows mounting and with sturdy grinding plates drum profile made of flat steel underneath the outer frame. Outer frame slightly inclined with Load-Lock profile for attaching tension beltsNote! To attach the belts in conjunction with drop sides, the drop sides must be opened! 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder, aluminum side bumpers, offset inwards as far as technically possible, steel underride guard, as much ground clearance as possible, quarter-shell mudguards in front of and behind each axle, suspension strip for aluminum ramps at the rear, plastic toolbox, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) SAF drum brake axles, with axle stopsAxle distance 1600 mm, air suspension with lifting & lowering valve 205 / 65 R 17.5, twin steel rims, factory silver 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable front coupling heads, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 24 volt, multi-chamber lights, amber LED lighting integrated in outer frame profile at the side, offset inwards by approx. 25 mm, 10 lights per side 2 white position lights at the front, protected, 2 white/red lane departure lights at the rear, additional LED work light(s) at the rear, switched via reversing light 2 x 7-pin and 1 x 15-pin swap-proof sockets at the front, without connecting cable Screen printing plates approx. 30 mm thick, for high point load capacity for forklift axle load up to max. 5,600 kg Special floor installation: test of new profiles, without bolting Coln Thomp Ug Dohgsgt Steel/checker plate covering in the wheel arch area, front wall/front stanchions, 25 mm aluminum hollow profile, approx. 800 mm high, steel corner stanchions in volume design, with viewing windows on both sides. Approval country: Germany, with Dekra approval and certificate (according to §13 EG - FGV), 24/7 service hotline, prepared for single-line license plate holder, contour marking with reflective strips according to ECE R 048, white at the sides and red at the rear

Condition: used, overall weight: 18,000 kg, empty load weight: 4,480 kg, maximum load weight: 13,520 kg, axle configuration: 2 axles, first registration: 05/2014, tire size: 445/45 r19,5, Year of construction: 2014, machine/vehicle number: a6d448c42c302ffbdb6a9c40f, Further information Fine-grained steel welded construction 1 gear support foot at the front, with straight lower section and single-sided operation in FR right Wheel chocks with holder, aluminum side bumpers, steel underride guard Half-shell mudguards protrude slightly over the main frame, bumpers at the rear Tandem trailer towing device Towbar with tested 50 mm towing eye, forwarding agent version, under-coupler towbar Axles + suspension BPW disc brake axles, manufacturer's choice Air suspension with lift & lower valve Wheels and tires 445 / 45 R 19.5, manufacturer's choice, steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake, Duomatic connection at the front, with connecting cable to the motor vehicle, EBS, electronic braking system with EBS plug at the front, with connecting cable Make Haldex, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Floor: Platform length approx. 7,300 mm, screen-printed floor Front wall: aluminum approx. 1,200 mm, steel corner stanchions in volume design Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 15-pin plug at the front, with connecting cable Approval / plates Country of registration: Germany, with Dekra approval and certificate Coln Toni Udzehhgegt 24/7 service hotline, prepared for single-line license plate holder, contour marking with reflective strips to ECE R 048, white at the sides and red at the rear

Condition: used, overall weight: 11,500 kg, empty load weight: 3,300 kg, maximum load weight: 8,200 kg, axle configuration: 2 axles, first registration: 06/2022, tire size: 235/75 r17,5, Year of construction: 2022, machine/vehicle number: 27acc7e85448c547af007afaa, Further information Welded steel construction, continuous tipping shaft at the rear with 80 mm ball bearings Front gear support foot, folding rear support, 2 wheel chocks with holder, steel underride guard, rear mud flaps across the entire width, quarter-shell mudguards, spare wheel, same make as basic tyres, steel rim, loose, 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery)Note! Dropside touches storage box when folded down. Lockable storage space for access ramps underneath the loading area, 1 pair of aluminum ramps 3,000 mm long, 360 mm wide, load capacity per pair 8,000 kg, (suspension bar for ramps at the rear) Drawbar with tested 40 mm towing eye, height-adjustable drawbar via spindle, max. adjustment range 300 mm Csln Thhjlhpzvjgogt BPW drum brake axles, axle/chassis laser-measured Reduction in tire wear and fuel consumption, parabolic suspension with maintenance-free steel/rubber bearings and mechanical axle load compensation (rocker compensation) 2-line compressed air brake systemColor-coded cable routing for easy servicing. Hand spindle parking brake, integral air reservoir, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer vehicle may only be towed by towing vehicles that guarantee the effectiveness of the ABS, 2 swap-proof coupling heads at the front, with connecting cables to the motor vehicle 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front 2 white/red lane departure warning lights at the rear, 2 x 7-pin non-interchangeable plugs at the front, with connecting cable Three-way tipping mechanism, hydraulic multi-piston press with lift limiter and safety cable, Low-pressure cylinder up to max. 170 bar, without throttle. If required, this can be retrofitted to the truck, hydraulic connection with SVK plug NW 10/3, incl. connecting hose Hydraulic actuation via truck power take-off Sturdy tipper body with 4 mm sheet steel floor, steel side wall structure, continuous side walls, hinged and pivoting with central locking at the bottom. Rear corner stanchions pluggable. Rear wall can be folded down and pivoted, with central locking at the bottom. Platform length approx. 5,000 mm, side walls with 6 hinges at the bottom, platform width 2420 mm 5 pairs of lashing eyes in the floor, 5 tons each Country of registration: Germany, with Dekra approval and certificate (according to §13 EG - FGV), 24/7 service hotline, prepared for single-line license plate holder, contour marking with reflective strips according to ECE R 048, white at the sides and red at the rear

Condition: new, overall weight: 35,000 kg, empty load weight: 6,350 kg, maximum load weight: 28,650 kg, axle configuration: 3 axles, tire size: 435/50 r19,5, machine/vehicle number: 59ade5d1599dcdee29033ac46, Further information Chassis saddle forwarding Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Suspension bar for aluminum ramps across the entire width Frame in reinforced design for vehicle loading (up to outer frame) Outer frame with Load-Lock profile approx. every 400 mm, for lashing strap attachment 10 pairs of lashing mushrooms embedded in the top/outside of the outer frame, 10 tons each 24 to. 2-speed support winch, single-sided operation, with semicircular lower section and straight connecting plate, with thrust compensation Folding rear support 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Quarter-shell mudguards in front of 1st axle and behind each axle with anti-spray flaps behind each axle Pair of ferry eyes, marked yellow 1 Spare wheel holder for 1 e-wheel, with wheel mounting kit 2 plastic toolboxes, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) Container lock, 4 pairs of locks embedded in the floor for 2 x 20 foot or 1 x 40 foot containers, foremost position recessed as hinged lock 10 pairs of stake pockets embedded in the outer frame, 70 x 40 mm internal dimensions 10 stake pockets embedded in the center of the floor, 70 x 40 mm inside dimensions Cgoln Told Ihlehhgjt 2 lashing/stanchion rails embedded transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer stanchions approx. 2170 mm), approx. 100 mm high. With 20 mm round steel slats, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). For lashing and inserting stanchions 80 x 80 rdnung: Position 2 and 4 according to Fliegl data sheet 20 stanchions, hot-dip galvanized Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them Storage space for aluminum ramps, ramps can be inserted from the rear 3 pairs of folding eyelets 10 tons in the outer frame (1x in front of the bulkhead and 2x in the rear area). Axles + suspension SAF disk brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle lift below the recomm. Driving height, therefore no warranty for tire damage 2 ride heights, adjustable via hand knob, 1 x for semi-mounted height 980 mm 1 x for semi-mounted height 1100 mm (Note! Vehicle with inclined position) Brake system 2-line compressed air brake system Colored cable routing for easy servicing. Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! With lifting & lowering valve 2 ride heights, adjustable via hand knob, 1 x for fifth wheel height 980 mm 1 x for fifth wheel height 1100 mm (Note! Observe overall height, excess height at customer risk) Driving height in conjunction with lift axle, when the lift axle is raised, the total loading or semitrailer height increases by 50 mm (with Mega Flex only with low driving height or semitrailer height) Vehicle driving stability system Wheels and tires 435/50 R19.5 tires of the manufacturer's choice Stee