Used Müller Agricultural Machines for sale (242)

Condition: new, overall weight: 18,000 kg, maximum load weight: 13,700 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,480 mm, Year of construction: 2024, * TRA 18.0: * 2 in 1 = for roll-off containers and as a low loader * RDÜ (tire pressure monitoring) * EBS electronic brake system * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 10 anthracite axles * Air suspension with manual lowering at the rear * Pull scissors 2,000 mm long with 40 mm drawbar and height adjustment device * Toolbox made of powder-coated sheet steel approx. 1,000 x 300 x 600 mm and spare wheel holder in basket design on the right side * Reflective contour band on the side and rear * Side impact protection * Plastic quarter fender with splash guard * Plastic impact protection buffer at the rear * Foldable A-sign at the rear * LED tail lights * 15-pin power plug * Main frame with raised outer frame for guiding the roll containers * Sheet steel floor with roller recesses in the bogie area * Cont. length of 5,500 - 7,000 mm possible * pneumatic 4-fold clamp locking and mechanical plug-in stop angle at the front of the track, load securing certificate according to DIN 30722 - 1 * Lasi package consisting of: 1 pair of 10 ton UVV lashing rings at the front of the bulkhead support and 3 pairs of 10 ton UVV lashing rings on the side in the outer frame, 4 x 2 ton lashing eyes in cloverleaf design and 4 x 8 ton lashing brackets embedded in the outer frame * Weld bead as anti-slip coating in the track area of the ramp * mechanical Rear drop supports * 1 pair of aluminum landing ramps (10.6 tons / pair) 2,800 x 470 mm suitable for rubber-tired and tracked vehicles (lockable storage compartment from the rear) * Chassis, bogie, locking parts, rear drop supports hot-dip galvanized * but the pull scissors, axles, air tank painted in a black tone * New vehicle without first registration with full manufacturer's warranty Dkobu Tsl Tq Nmjl Dxel * Errors and prior sale subject to reservation * Available immediately from Egestorf on the A7

Condition: new, overall weight: 18,000 kg, maximum load weight: 13,700 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,480 mm, Year of construction: 2024, * TRA 18.0: * 2 in 1 = for roll-off containers and as a low loader * RDÜ (tire pressure monitoring) * EBS electronic brake system Djbu Tlol Tpc As Dxokl * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 10 anthracite axles * Air suspension with manual lowering at the rear * Pull scissors 2,000 mm long with 40 mm drawbar and height adjustment device * Toolbox made of powder-coated sheet steel approx. 1,000 x 300 x 600 mm and spare wheel holder in basket design on the right side * Reflective contour band on the side and rear * Side impact protection * Plastic quarter fender with splash guard * Plastic impact protection buffer at the rear * Foldable A-sign at the rear * LED tail lights * 15-pin power plug * Main frame with raised outer frame for guiding the roll containers * Sheet steel floor with roller recesses in the bogie area * Cont. length of 5,500 - 7,000 mm possible * pneumatic 4-fold clamp locking and mechanical plug-in stop angle at the front of the track, load securing certificate according to DIN 30722 - 1 * Lasi package consisting of: 1 pair of 10 ton UVV lashing rings at the front of the bulkhead support and 3 pairs of 10 ton UVV lashing rings on the side in the outer frame, 4 x 2 ton lashing eyes in cloverleaf design and 4 x 8 ton lashing brackets embedded in the outer frame * Weld bead as anti-slip coating in the track area of the ramp * mechanical Rear drop supports * 1 pair of aluminum landing ramps (10.6 tons / pair) 2,800 x 470 mm suitable for rubber-tired and tracked vehicles (lockable storage compartment from the rear) * Chassis, bogie, locking parts, rear drop supports hot-dip galvanized * but the pull scissors, axles, air tank painted in a black tone * New vehicle without first registration with full manufacturer's warranty * Errors and prior sale subject to reservation * Available immediately from Egestorf on the A7

Condition: new, overall weight: 18,000 kg, maximum load weight: 14,650 kg, axle configuration: 2 axles, Year of construction: 2024, * RS-T 18.0 / 018: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Disc brakes * Duomatic brake connection Dkjbu Tl Dsl Tqkwsxel * 2 x 10 ton SAF axles * Air suspension with automatic lowering when the brake is uncoupled * Pull scissors 2,300 mm long with 40 mm towing eye and height adjustment via tension spring & spindle * Plastic tool box on the right side, closed. Plastic fenders * closed side impact protection as advertising space * underrun protection with 2 impact buffers * foldable A-sign at the rear for waste disposal * LED tail lights with protective roof * 2 x 7-pin power plugs * hot-dip galvanized chassis (without air tank, axles, pull scissors, etc.) * roller track length approx. 6,950 mm * roller container is clamped by pneumatic 4-way claw locking * there are 2 plug-in container stops at the front with 2 additional plug-in positions * driving height unloaded approx. 1,165 mm * -- permissible total weight of 20,000 kg technically possible-- * suitable for 5,000 - 7,000 mm container lengths * new vehicle with manufacturer's warranty * errors and prior sale subject to reservation * available immediately from Egestorf

Condition: new, overall weight: 19,000 kg, maximum load weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 19.0: Djbuemi Tcqe Tl Dxjkl * WabcoEBS- E (electronic braking system) * RDÜ tire control monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 11 to. Gigant axles * Air suspension with lifting and lowering system * Drawbar with 50 mm flange drawbar eyelet and height adjustment by 110 mm using offset plate * Jost support winch at the front * External folding supports at the rear * Plastic tool box approx. 750 x 350 x 300 mm on the right side * Side impact protection * Plastic quarter fender * 15-pin power plug * Multi-chamber tail lights * Reinforcement package for drilling equipment transport on the chassis * 50 mm softwood floor in clamped design * Device in front of the bulkhead for subsequent installation of cont. locks * Screwed bulkhead made of smooth sheet metal * Divided side walls made of sheet steel - trapezoidal profile - foldable with folding stanchion in the middle * Steel rear wall can be inserted between the ramps - holder when not in use inside in front of the bulkhead * Rear stanchions screwed * Perforated outer frame approx. 45 degree bent with 2 ton lashing force every 480 mm * Installation of 3 ton lashing brackets every 600 mm possible * Lasi package: in the front and rear corners 1 x 10 ton UVV lashing ring, on the sides 2 x 8 ton UVV lashing rings retractable in the outer frame, various holes for 1.2 ton in the front and end beams. Lashing option * one-piece slide-in ramps approx. 2,750 x 620 mm * Rear approach slope approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, folding supports and ramps hot-dip galvanized * ---Axles, air tank, flange drawbar eye and support winch painted in a black tone--- * Loading height unloaded approx. 940 mm * Loading height loaded approx. 910 mm * Wheelbase: 1,810 mm * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available from week 22/2025 from Egestorf

Condition: new, overall weight: 21,000 kg, maximum load weight: 16,750 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 21.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 11 to. Gigant axles * Air suspension with lifting and lowering system * In front of the bulkhead and rear slope, device for subsequent installation of container locks for transporting 20" containers * Drawbar with 50 mm flange drawbar eyelet and height-adjustable drawbar * Jost support winch at the front * External folding supports at the rear * Plastic tool box approx. 750 x 350 x 300 mm on the right side * Side impact protection * Plastic quarter fender * 15-pin power plug * LED lights * 21 tonne GG version with reinforced frame and reinforced axles * Reinforcement package for drilling equipment transport on the chassis * 50 mm softwood floor in clamped version * In front of the bulkhead, device for subsequent installation of container locks * Screwed bulkhead made of smooth sheet metal * Divided side walls made of sheet steel -trapezoidal profile- foldable with folding stanchion in the middle * steel rear wall can be inserted between the ramps - holder when not in use inside in front of the front wall Dkebeq Dyu Uju Tl Dxel * rear stanchions screwed * perforated outer frame bent at approx. 45 degrees with 2 ton lashing force every 480 mm * installation of 3 ton lashing brackets every 600 mm possible * 1 x 10 ton lashing ring in the front and rear corners * Lasi package with 2 x 8 ton lashing rings on each side, retractable in the outer frame, various holes in the front and end beams for 1.2 ton lashing option * one-piece mechanical Grating loading ramps with spring mechanism for one-man operation approx. 3,000 x 620 mm (can be pushed together to 20 mm) * Rear approach slope approx. 860 mm chassis * Drawbar, bulkhead, tailgate, folding supports and loading ramps hot-dip galvanized * Axles, springs, air tank and support winch painted in a black tone * Loading height unloaded approx. 940 mm * loaded approx. 910 mm * Wheelbase: 1,810 mm * Tires: 235/75R17.5 * Painting of the side walls Color freely selectable up to approx. 2 weeks before production date, but no metallic or special colors * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available from week 20/2025

Condition: new, overall weight: 30,000 kg, maximum load weight: 23,500 kg, axle configuration: 3 axles, Year of construction: 2024, Equipment: ABS, * T 3: * ABS braking system * Emergency release device for spring-loaded cylinders Dkjbustplwfe Tl Dxol * Drum brakes * 3 x 11 ton BPW Eco axles * Parabolic springs * Mechanical axle compensation at the rear * Lateral impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle closed plastic mudguards and rear axle straight galvanized. Sheet steel aprons each with splash guard * Reflective contour tape on the side and rear * Hinged lid (hot-dip galvanized) for the toolbox in the bogie platform * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm - black powder-coated - on the side under the chassis * 15-pin power plug * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * 4 stake pockets on each side (but no stakes available) with simultaneous lashing option * La-Si package consisting of: 2 lashing eyes (6.4 tons) at the front left & right on the main frame of the bogie platform * 5 pairs of UVV lashing rings that can be swiveled and lowered * Can be loaded in all directions and embedded in the outer frame in the corners 13.4 tons. otherwise 10 tons * 6 pairs of mechanical folding booms for 3 mtr. total width (but not in the rear slope) * Widening planks stored in a storage compartment under the loading area * Excavator boom storage above rear axle to the end beam approx. 2,100 mm long (2 pairs of 6.4 ton lashing rings on the side in the excavator boom storage) * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable tip section and load holding valves, hydraulic lateral ramp shifting * Hydraulic. Flow divider in the trailer (with hydraulic pump output in the truck of over 40 liters to max. 140 liters / min.), two-line hydraulics * Loading area above the turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm, (incl. 860 mm approach slope) * Loading height when loaded approx. 860 mm +/- 30 mm compensation unit * Chassis, bogie, folding boom, rear drop supports and loading ramps hot-dip galvanized. * Axles, springs, pull scissors, air tank etc. painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available immediately from Egestorf

Condition: new, overall weight: 18,000 kg, maximum load weight: 14,180 kg, axle configuration: 2 axles, Year of construction: 2024, * RA-T-Kombi 18.0 : * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Disc brakes 19.5" * Duomatic brake connection * 2 x 10 ton SAF axles * Air suspension with automatic lowering when the brake is uncoupled Djbusl Tm Dde Tl Dxekl * Pneumatically lowerable tow bar 2,100 mm long with 40 mm tow eye and height adjustment device * Reflective contour strip on the side and rear * 15-pin power plug * LED lighting system 12/24 V * 2 additional LED reversing lights * Closed side collision protection as advertising space * Plastic fender with splash guard * Plastic impact protection buffer at the rear * Foldable A-sign at the rear * Roller recesses in the bogie area for roll-off container transport Cont. length from 5,500 - 7,000 mm possible * pneumatic 4-fold clamp locking and mechanical plug-in stop angles at the front of the track (2 positions) * Transport of up to 2 skip containers with a max. 10m³ volume possible * 8 interchangeable trough stops for lateral centering of the troughs * Trough stops at the front and rear with swinging stop, 2 lashing eyes and 4 x UVV lashing rings (10.6 tonnes) on each side for hanging clamping elements for positive and non-positive clamping of the troughs, lockable storage compartment for the trough stops etc. embedded in the rear of the frame * 2 x storage boxes made of galvanized perforated sheet metal approx. 1,000 x 500 x 500 mm for container nets etc. * Chassis, underrun protection and locking parts hot-dip galvanized * Axles, air tank, pull scissors and bogie painted in a black tone * Driving height when loaded approx. 1,130 mm, unloaded approx. 1,150 mm * Load securing certificate available * --Total permissible weight of 20,000 kg technically possible-- * Vehicle has a daily registration in 06/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer warranty * Errors and prior sale subject to reservation * Available immediately from Egestorf on the A7

Condition: new, overall weight: 40,000 kg, maximum load weight: 30,500 kg, axle configuration: > 3 axles, Year of construction: 2023, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 tonne Gigant axles * Air suspension with manual lowering at the rear * Pressure gauge for determining the load weight (axles separated into 2 air suspension circuits) * Warning sign packages at the front & rear * Reflective contour tape on the sides and at the rear, * Rotating beacon (removable) at the rear * 15-pin power plug * LED tail lights * Straight tow bar with 50 mm tow eye and infinitely variable height adjustment * Closed at the front. Plastic individual mudguards * Straight steel mudguards at the rear, each with splash guard (spray suppression * Side impact protection * Front section in front of the bogie platform by approx. 520 mm with 45° corners and 3 storage compartments including lockable hinged lids (hinged lid opens to the rear) * Chassis made of high-strength fine-grain steel * Floor above the bogie platform made of 50 mm and in the low-loading platform made of 60 mm softwood * Outer planks of the loading ramps made of 50 mm hardwood * Lasi package consisting of: 2 lashing rings 6.4 tonnes at the front left and right on the main frame of the bogie platform, 1 pair of 13.4 tonnes lashing rings on the outside frame at the front and rear, and 1 pair of 10 tonnes lashing rings on the side, can be swivelled and lowered, can be loaded in all directions and embedded in the outside frame, 5 bolted to the outside frame of the wheel wells ton lashing rings (2 on the front wheel well and 1 on the rear), 2 pairs of 6.4 ton lashing rings on the side in the excavator arm holder Dksbu Tol Tnv Isl Dxel * 11 pairs of folding booms for 3 mtr. Total width (but not in the rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for the widening planks made of sheet steel, mounted across the loading area in front of the 1st rear axle * Excavator boom storage above the rear axle to the end of the approach slope approx. 2,300 x 740 x 190 mm * 2 wheel recesses on each side, approx. 640 mm wide - front 340 mm deep, rear 220 mm deep - with retractable cover (storage for the covers at the front on the bogie platform) for transporting wheel loaders with a wheelbase of 3,100 - 3,640 mm * mechanical support legs at the rear * hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm * hydraulic. lateral ramp shift * Loading area above the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loading height when loaded approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, bogie, folding boom, rear support legs and ramps hot-dip galvanized * Axles, air tank and pull scissors painted in a black tone * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation, * Available for immediate delivery from Egestorf

Condition: new, overall weight: 18,000 kg, maximum load weight: 14,650 kg, axle configuration: 2 axles, Year of construction: 2024, * RS-T 18.0 / 018: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Disc brakes * Duomatic brake connection * 2 x 10 ton SAF axles * Air suspension with automatic lowering when the brake is uncoupled * Pull scissors 2,300 mm long with 40 mm towing eye and height adjustment via tension spring & spindle Dkebu Tljl Tpy Hj Dxel * Plastic tool box on the right side, closed. Plastic fenders * closed side impact protection as advertising space * underrun protection with 2 impact buffers * foldable A-sign at the rear for waste disposal * LED tail lights with protective roof * 2 x 7-pin power plugs * hot-dip galvanized chassis (without air tank, axles, pull scissors, etc.) * roller track length approx. 6,950 mm * roller container is clamped by pneumatic 4-way claw locking * there are 2 plug-in container stops at the front with 2 additional plug-in positions * driving height unloaded approx. 1,165 mm * -- permissible total weight of 20,000 kg technically possible-- * suitable for 5,000 - 7,000 mm container lengths * new vehicle with manufacturer's warranty * errors and prior sale subject to reservation * available immediately from Egestorf

Condition: new, overall weight: 8,800 kg, maximum load weight: 6,110 kg, axle configuration: 1 axle, Year of construction: 2024, * KWH 8.8 ML: * RDÜ tire pressure monitoring * EBS brake system * Drum brake * BPW axle * Parabolic springs * Support winch at the front * Spring-supported square tube supports at the rear with base plate safety plug pins for different support heights * Drawbar with 40 mm screw eyelet (height adjustable mm) * 15-pin power plug * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and cross members Dksbu Tlou I Iqle Dxol * Closed mudguard made of sheet steel with splash guard * Closed. side impact protection can be used as advertising space * plastic tool box with floor insert (horizontal installation) approx. 500 x 350 x 400 mm * swiveling cable drum structure, clear width between the drum arms 1,700 mm - with tension lock to secure the drum at the ends of the support arms and locking of the cable drum structure to the chassis using a claw lock located in the middle * motor-hydraulic drum drive with oil motor * valves and movable rubber-coated drive rollers * hydr. Speed controller and brake for drum drive * Steel drum shaft with 76 mm diameter as well as centering and rotating ends * 1 pair of centering cones made of polyamide, stepped * Hydraulic pump unit with diesel engine * Fuel tank and manual starter * 6.5 HP with gear pump (150 bar) * Color hot-dip galvanized * New vehicle with full manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: new, overall weight: 8,800 kg, maximum load weight: 6,110 kg, axle configuration: 1 axle, Year of construction: 2025, * KWH 8.8 ML: * RDÜ tire pressure monitoring * EBS brake system * Drum brake * BPW axle * Parabolic springs * Support winch at the front * Spring-supported square tube supports at the rear with base plate safety plug pins for different support heights * Drawbar with 40 mm screw eyelet (height adjustable mm) * 15-pin power plug * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and cross members * Closed mudguard made of sheet steel with splash guard * Closed. side impact protection can be used as advertising space * plastic tool box with floor insert (horizontal installation) approx. 500 x 350 x 400 mm * swiveling cable drum structure, clear width between the drum arms 1,700 mm with tension lock to secure the drum at the ends of the support arms and locking of the cable drum structure to the chassis using a claw lock located in the middle * motor-hydraulic drum drive with oil motor * valves and movable rubber-coated drive rollers * hydr. Speed controller and brake for drum drive Dobuou I Iqre Tl Dxjkl * Steel drum shaft with 76 mm diameter as well as centering and rotating ends * 1 pair of centering cones made of polyamide, stepped * Hydraulic pump unit with petrol engine * Fuel tank and hand starter * 13 HP with gear pump (150 bar) * 315/80 R 22.5 tires * 2,690 kg empty weight * Vehicle is hot-dip galvanized * New vehicle with full manufacturer's warranty * Errors and prior sale subject to change * Available week 18/2025 from Egestorf

Condition: new, overall weight: 50,000 kg, maximum load weight: 38,900 kg, axle configuration: > 3 axles, Year of construction: 2025, * T5 profile 50.0: * Wabco EBS (electronic braking system) * RDÜ (tire pressure monitoring) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 to. Gigant axles * last axle with trailing steering (the trailing axle can be locked from the driver's cab for maneuvering purposes without installation on the truck, and additionally using a switch on the trailer) the lock must be switched off before driving on public roads * air suspension, lifting and lowering system with RtR valve * 3rd axle can be lifted (with lifted axle, driving height + 30 mm) * forced unloading and forced lowering of the lift axle for maneuvering purposes (installation on the truck side required) with speed-dependent switching via the EBS electronics * Smartboard as an information tool with pressure sensors to display the total axle load for each axle group * tire pressure monitoring with display option in the truck via EBS signal (without installation on the truck side) Dkjbu Tlel Tihuo Dxsl * mechanical warning sign package for 3 m total width * 1,500 mm long towing scissors with 50 mm towing eyelet and man. Height adjustment * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm on the left side * Plastic mudguard VA and galvanized sheet steel mudguards HA * Front of the bogie platform with 45° corners and 3 storage compartments with lockable hinged lids (hinged lid opens to the rear) * Shortening of the low-loading platform by 500 mm to 6,280 mm including extended offset by 500 mm to the front * LaSi package: 2 x 6.4 ton lashing eyes at the front in the corners, 2 x 13.4 ton UVV lashing rings on the sides in the corners at the front and rear and 5 x 10 ton lashing rings on the sides. UVV lashing rings (can be swivelled and lowered and can be loaded in all directions), 4 stake pockets on each side with a simultaneous 2 ton lashing option, 1 x 16 ton UVV lashing ring on the rear cross member * Rubber covering on the folding frame, approach slope and on the running surface of the low-loader platform * Bamboo wood between the longitudinal beams in front of the excavator support shelf * Extendable and foldable extension boom for 3 m total width (plank holder under the chassis on the right side) * Excavator boom support with reinforcement profile from the last axle to the end support approx. L = 2,350 x W = 770 x D = 270 mm, 2 pairs of 6.4 ton UVV lashing rings on the side in the excavator boom support * hydr. Folding ramp with dual-line hydraulics and extendable tip section approx. 4,650 x 720 mm including load holding valves and hydraulic side shift * hydraulic rear support * hydraulic flow divider (with hydraulic pump output in the truck of over 40 ltr./min. up to max. 140 ltr./min.), * Loading height when loaded 890 mm +/- 20 mm due to the air suspension * Loading area above the turntable: 2,600 + 390 x 2,520 mm * Low bed loading area: 6,280 + 500 x 2,520 mm, including 860 mm approach slope * Chassis, bogie, drawbar, widening brackets, loading ramps hot-dip galvanized * Drawbar, axles, hydraulic. Axle supports and air tank painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available immediately from week 25/2025 * Sample images

Condition: new, overall weight: 18,000 kg, maximum load weight: 14,550 kg, axle configuration: 2 axles, Year of construction: 2025, * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * 19.5" disc brakes * Automatic braking when the transverse clamping units are opened * 2 x 10 ton BPW wide-track axles * Air suspension (automatic lowering when the brake is uncoupled) * Tire pressure monitoring with display option in the truck via EBS signal - no truck-side installation required - * Pneumatically lowering towing bar, 1,800 mm long, with 40 mm towing eye and height adjustment via tension spring and turnbuckle * Plastic toolbox, 858 x 500 x 500 mm, on the right side * Storage box for cargo net made of galvanized perforated sheet metal, 1,000 x 500 x 500 mm, on the side * Closed plastic fenders, front and rear * Closed side impact protection (RAL 9010 pure white) as Advertising space * Rear underrun protection * Plastic bumper buffers at the rear * Foldable A-sign * Hazardous goods sign with accompanying document pocket and reflective parking warning sign at the rear * 15-pin power connector * LED lighting system with protective roof * 2 LED reversing lights (switched via reverse gear) * Additional front loading with rear track lowering and plug-in stop * Roller recesses in the area of the turntable with mechanical locking Adjustable stop angles (2 positions) on the front left and right of the tracks * Track length approx. 6,830 mm * Pneumatic 4-point clamp locking system * For the transport of external roller containers according to DIN 30722 Part 1 - DEKRA load securing certificate available * Loaded loading height approx. 1,130 mm * Chassis and locking components hot-dip galvanized * Air tank, axles, turntable, and tension scissors painted in a black tone * --GVW of 20,000 kg technically possible-- * New vehicle without first registration and with manufacturer's warranty * Errors and prior sale subject to change * Available from week 17 of 2025 Dkebu Tjl Tn U Rjl Dxjl * Sample images

Condition: new, overall weight: 14,400 kg, maximum load weight: 10,950 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2024, * ETÜ-TA-ER 14.4 Plateau: Dkobu Tl Dsq Dyvnsxjl * RDÜ (tire pressure monitoring) * EBS (electronic braking system), * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 ton BPW axles * Air suspension with lifting and lowering system * mechanically adjustable 3 mtr. Warning sign packages at the front and rear * Drawbar height adjustable by 300 mm with 40 mm flange drawbar eye * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (thus B dimension of approx. 8,080 mm) * Support winch at the front * External folding supports at the rear * Plastic tool boxes approx. 750 x 350 x 300 mm on the left and right sides * Side impact protection * Underrun protection * Plastic quarter fender * 15-pin power plug * LED lighting system 12 / 24 V * 2 additional LED reversing lights. at the rear (switched via reverse gear) * 1 LED rotating beacon (removable incl. holder) at the rear * 50 mm softwood floor * 2 pairs of container locks (extendable to 3 mtr. Cont. external width) and lockable * Locking dimension pushed in according to ISO - DIN 15190 = 2,259 mm. Cont. locks pulled out = 2,819 mm (this dimension is not according to DIN) with an absolute external width of 3,000 mm * Perforated external frame bent at approx. 45 degrees with 2 ton. lashing force every 480 mm, installation of 3 ton. drop lashing brackets every 600 mm possible - 5 x 3 ton. UVV lashing brackets installed on the sides -, 1 x 6.3 ton in the corners at the front and rear. Lashing ring (at the front directly behind the cont. locks in the wooden floor and at the back in the end beam) in the front and end beam various holes for 1.2 ton lashing option * 1 pair of aluminum slide-in ramps approx. 3,570 x 410 mm (load capacity 10 ton / pair) suitable for rubber-tired and tracked vehicles * storage compartment below the loading area in the chassis from the rear * ---Chassis, drawbar, front wall, underrun protection and rear supports hot-dip galvanized--- * Axles, air tank, front support winch and flange drawbar eye painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available immediately from Egestorf on the A7

Condition: new, overall weight: 48,000 kg, maximum load weight: 39,030 kg, axle configuration: 3 axles, loading space length: 8,500 mm, loading space width: 2,520 mm, Year of construction: 2024, * TS 3 profile 30.0: * Wabco EBS-E (electronic braking system) * RDÜ (tire pressure monitoring) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco Plus axles * Air suspension with lifting and lowering system and RtR valve * Last axle with self-steering and electro-pneumatic steering lock * Smartboard control box mounted on the trailer as an information tool with pressure sensors for total axle load display * Side impact protection * Support winches at the front and mechanical swivel supports at the rear of the chassis * 15-pin power plug * LED lighting system 12/24V * LED rotating beacon (removable) at the rear left * Mech. adjustable warning sign packages at the front and rear * straight sheet steel mudguards * spare wheel holder under the chassis on the right side * saddle platform with 45° bevelled front corners and tool box at the front made of galvanised sheet steel W = 2,480 x H = 500 x L = 665 mm with hinged lid * 400 mm aluminium side walls (RAL 9010 pure white) on the side of the saddle platform, foldable and removable * rear wall -150 mm- high * rear slope on the saddle platform to the low bed approx. 700 mm long * saddle platform with 50 mm wooden planks and low-loading platform with 60 mm wooden planks * tear plate over the axles Dksbu Tljpk D I Aj Dxel * 8 x mechanical folding extensions to 3 mtr. total width but not in the rear slope (extension planks available with storage on the saddle platform) * Lasi package: 2 x 6.3 tonnes on the saddle platform each. lashing ring and 3 x 5 ton lashing bars on the side in the outer frame, in the low-loading platform 2 x 13.4 ton lashing rings and 4 x 10 ton lashing rings that can be swiveled and lowered into the outer frame, 2 x 6.4 ton lashing eyes on the side and 1 lashing ring at the back in the excavator boom storage area * Excavator boom storage area from the end of the last rigid axle via the steering axle to the end support with internal reinforcement profile approx. L = 2,450 x W = 770 mm x D = 270 mm * 2 x container locks directly after the crank in the low-loading platform * mechanical one-piece hot-dip galvanized hydraulic loading ramps approx. 3,000 x 720 mm (mechanically laterally adjustable) * 4-way control block for later retrofitting of hydraulic by the customer. Ramp shift * the outer board on the ramp is made of 50 mm hardwood * Loading area of the semi-trailer platform: approx. 3,900 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Loading height unloaded approx. 910 mm (incl. 860 mm approach slope) * Fifth wheel height approx. 1,220 mm (suitable for 2- and 3-axle tractor units) * Chassis, loading ramps, folding supports at the rear, widening brackets hot-dip galvanized * Axles, support winches, air tank painted in a black tone * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available from week 30/2025

Condition: new, overall weight: 48,000 kg, maximum load weight: 37,430 kg, axle configuration: 3 axles, Year of construction: 2024, * TS 3 RM ML 30.0: * Wabco-EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes Dkobu Tjtpta Dol Dxel * 3 x 11 ton BPW axles * Air suspension with lifting and lowering system and RtR valve * Starting aid for maneuvering purposes switched to the first axle via EBS (without installation on the truck side) * Smart board mounted on the trailer as an information tool with pressure sensors for displaying the total axle load * Last axle as a trailing steering axle with electro-pneumatic steering lock * Trailing axle locked by the driver. for maneuvering purposes switched via EBS (without truck-side installation) * 2nd kingpin position 2 * side impact protection, support winches at the front and swivel supports at the rear of the chassis * 15-pin power plug * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * 2 additional LED reversing lights * 7-pin socket on the rear side for extra-long lighting * Side marker lights with indicator control * Tire pressure monitoring with display option in the truck via EBS signal (without truck-side installation) * mech. adjustable warning sign packages at the front and rear * straight sheet steel mudguards * spare wheel holder in front of the bulkhead cross member (without spare wheel) * saddle platform with 45° bevelled front corners and front tool box made of galvanised powder-coated sheet steel W = 2,480 x H = 500 x L = 665 mm with hinged lid * 400 mm aluminium side walls (in the desired RAL colour) on the side of the saddle platform, foldable and removable * rear wall -150 mm- high * rear slope on the saddle platform to the low bed approx. 700 mm long with checker plate covering and a perforated strip at the end for hanging aluminium docking ramps * saddle platform with 50 mm clamped wooden planks and low-loading platform with 60 mm clamped wooden planks * tear plate over the axles * 9 x mechanical folding extensions to 3 mtr. Total width but not in the rear slope (widening planks available with closed storage compartment across the direction of travel under the loading area) * 3 slots under the saddle platform for storing optional aluminum ramps or wooden planks for wheel well cover * Swivel arm as a support for connecting cables from the truck to the trailer * LaSi package consisting of: outer frame perforated on the saddle platform, bent at 45° with hole pattern for lashing devices (2 tonnes lashing force per lashing point at a distance of at least 480 mm * 3 x 13.4 tonnes lashing rings sunk into the ground on each side (1 x on the saddle platform, 1 x on the longitudinal beams after the bend and 1 x above the middle axle next to the longitudinal beam) * 3 x 13.4 tonnes lashing rings on each side on the outer frame (1 x start of the saddle platform bend, 1 x start of the ramp, 1 x end of the ramp) * 2 x 10 ton lashing rings on each side (1 x between the front wheel recess and 1st axle and 1 x between the 2nd and 3rd axle) * 3 x 5 ton lashing rings screwed to the outer frame of the wheel recesses (2 on the front and 1 on the rear wheel recesses) * extended excavator boom support from the end of the last rigid axle over the steering axle to the end support with internal reinforcement profile approx. W = 770 mm x D rear = 270 / depth front 170 mm, 2 x 6.4 ton lashing rings on each side in the excavator boom support * 2 wheel recesses on each side, 390 mm deep and 640 mm wide for transporting wheel loaders with a wheelbase of 3,000 - 3,590 mm with a tire diam

Condition: new, overall weight: 8,800 kg, maximum load weight: 6,110 kg, axle configuration: 1 axle, Year of construction: 2025, * KWH 8.8 ML: * RDÜ tire pressure monitoring * EBS brake system * Drum brake * BPW axle * Parabolic springs * Support winch at the front * Spring-supported square tube supports at the rear with base plate safety plug pins for different support heights * Drawbar with 40 mm screw eyelet (height adjustable mm) * 15-pin power plug * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and cross members * Closed mudguard made of sheet steel with splash guard * Closed. side impact protection can be used as advertising space * plastic tool box with floor insert (horizontal installation) approx. 500 x 350 x 400 mm * swiveling cable drum structure, clear width between the drum arms 1,700 mm with tension lock to secure the drum at the ends of the support arms and locking of the cable drum structure to the chassis using a claw lock located in the middle * motor-hydraulic drum drive with oil motor * valves and movable rubber-coated drive rollers * hydr. Speed controller and brake for drum drive * Steel drum shaft with 76 mm diameter as well as centering and rotating ends * 1 pair of centering cones made of polyamide, stepped * Hydraulic pump unit with petrol engine * Fuel tank and hand starter * 13 HP with gear pump (150 bar) * 315/80 R 22.5 tires Dkobusu I Iqfj Tl Dxel * 2,690 kg empty weight * Vehicle is hot-dip galvanized * New vehicle with full manufacturer's warranty * Errors and prior sale subject to change * Available week 18/2025 from Egestorf

Condition: new, overall weight: 11,900 kg, maximum load weight: 9,300 kg, axle configuration: 2 axles, loading space length: 6,000 mm, loading space width: 2,010 mm, loading space height: 325 mm, Year of construction: 2024, * ETS-TA-B 11.9: * EBS (electronic braking system) * RDÜ (tire pressure monitoring) * Drum brakes, 2 x 5.5 tonne Gigant axles * Parabolic springs with compensation unit * Drawbar height adjustable by 300 mm * Jost support winch * Mechanical fall supports at the rear * Plastic toolbox at the front right on the bulkhead * Side impact protection * LED lighting * 50 mm softwood floor * 1 x 6.3 tonne lashing ring in the corners in front of the bulkhead and the end support and 2 6.3 tonne UVV lashing rings on the sides embedded in the outer frame * One-piece mechanical Grating ramps with spring mechanism for one-man operation approx. 2,350 x 870 mm (internal distance 20 mm, ramps cannot be moved) * Front wall, side walls, fender and drawbar hot-dip galvanized * Axles, springs, air tank, support winch at the front painted in a black tone * New vehicle with full manufacturer's warranty * Errors and prior sale subject to reservation * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire control monitoring system * Emergency release device for spring-loaded cylinders * Drum brakes Dksbu Tlol Th Aps Dxel * 4 x 11 to. Gigant axles * Air suspension with lifting and lowering system and RtR valve * Smart board for determining load weight * Warning sign packages at the front and rear * Reflective contour tape on the side and at the rear * Rotating beacon (removable) at the rear * LED light * Straight pull scissors with 50 mm towing eyelet and stepless height adjustment * Tool box made of powder-coated sheet steel and spare wheel holder in basket design on the right side * Closed at the front. Plastic individual fenders * Straight steel mudguards at the rear, each with splash guard (spray mist suppression) * Side impact protection * Front of the bogie platform extended by 520 mm with 45° corners and 3 recessed storage compartments including lid and lockable * Chassis made of high-strength fine-grain steel * Floor above the bogie platform made of 50 mm and in the low-loading platform made of 60 mm softwood * Outer planks of the loading ramps made of hardwood, * 4 stake pockets on each side (but no stakes available) with simultaneous 2 ton lashing option * Lasi package consisting of: 2 lashing eyes 6.4 ton. at the front left and right on the main frame of the bogie platform * 2 pairs of 13.4 ton lashing rings on the outer frame at the front and rear and 4 pairs of 10 ton lashing rings on each side. can be swivelled and lowered * can be loaded in all directions and embedded in the outer frame * 2 pairs of 6.4 ton lashing rings on the side in the excavator boom storage * 8 pairs of galvanised folding booms for 3 m total width (but not in the rear slope) * Widening planks stored in a storage compartment on the left side * Excavator boom storage above the rear axle to the end of the approach slope approx. 2,100 x 740 x 190 mm * mechanical fall supports at the rear * hydraulic folding ramps with hydraulically extendable tip section approx. 4,650 x 720 mm including hydraulic lateral ramp shifting and load holding valve * Loading area above the turntable: approx. 2,990 x 2,520 mm * rear loading area: approx. 6,780 x 2,520 mm * loading height incl. Approx. 890 mm, +/- 20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, bogie, ramps, folding boom and mechanical support supports hot-dip galvanized * Axles, pull scissors, air tank and slewing ring painted in a black tone * Tires 235/75 R 17.5 * New vehicle without first registration with manufacturer's warranty *

Condition: new, overall weight: 14,400 kg, maximum load weight: 10,360 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 14.4: * RDÜ (tire pressure monitoring with display option in the truck via EBS signal without truck-side installation) * electronic braking system EBS * emergency release device for spring-loaded cylinders * drum brakes * 2 x 5.5 ton. Gigant axles * Air suspension with lifting and lowering system * Height-adjustable drawbar by 300 mm * Jost support winch at the front * External hot-dip galvanized folding supports at the rear * Plastic toolbox at the front right on the outside of the bulkhead * Side impact protection * Plastic quarter fender * LED lighting system * 15-pin power plug Dksbsndpn Seu Tl Dxjl * Hot-dip galvanized chassis as well as drawbar, bulkhead and rear wall * 50 mm softwood floor * Device for subsequent installation of 20" cont. locks at the front and rear * Screwed bulkhead made of smooth sheet metal * Side walls made of sheet steel - trapezoidal profile - foldable with side wall spring lifter * Hot-dip galvanized rear stanchions screwed * Perforated outer frame bent at approx. 45 degrees with 2 ton lashing force every 480 mm, installation of 3 ton lashing brackets every 600 mm possible, 1 x 6.3 ton lashing ring in the front and rear corners, various holes in the front and end beams for 1.2 ton lashing option * 1 pair of aluminum docking ramps approx. 3,310 x 400 mm (load capacity 8 ton / pair) suitable for rubber-tired and tracked vehicles, storage compartment below the loading area in the chassis from the rear * Vehicle hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available from week 19/2025 from Egestorf

Condition: new, overall weight: 11,900 kg, maximum load weight: 8,450 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 22,420 mm, loading space height: 1,500 mm, Year of construction: 2024, * KA-TA-R 11.9 Masterline: * incl. 1 mtr grid attachments Djbu Tl Dep Ncl Sexskl * EBS brake system * Emergency release device for spring brake cylinders * RDÜ tire pressure monitoring * Drum brakes * 2 x 5.5 to. BPW axles * Parabolic springs with tandem compensation unit * 300 mm height-adjustable hot-dip galvanized drawbar with 40 mm flanged drawbar eye * Jost mech. support winch at the front * 2 mechanical hot-dip galvanized folding supports at the rear * Tool box made of galvanized sheet steel on the right side * 15-pin power plug * Bolted underride guard with LED tail lights * Plastic quarter mudguards * Mesh hooks at the side and rear in the bearings of the central locking system and 3 pieces on the outside of the bulkhead * Hot-dip galvanized chassis * Fully galvanized steel Pal. 3 side tipper body * Full-length side walls without central stanchion can be folded down with dropside spring lifter * Tailgate can be folded down and swung open via man. Central locking * hot-dip galvanized bolted rear stanchion * 1 x 5 to. lashing ring in each corner Lashing ring recessed and foldable in each corner and 4 x 3 tons at each side. * Lashing rings recessed in the outer frame and hinged * 4 mm sheet steel floor * Rear mounting rail for feeder ramps * Reinforced body with load securing certificate to EN 12642 XL * 1 pair of aluminum docking ramps approx. 3,570 x 400 mm (load capacity 8 to. / pair) suitable for rubber-tyred and tracked vehicles * Storage compartment lockable from the rear under the loading area recessed in the chassis * 235/75 R 17.5 tires * Axles, springs, air reservoir, drawbar and support winch painted black * Hot-dip galvanized side wall paint * 1 metre galvanized grid attachments * Sample pictures * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available from Egestorf on the A7

Condition: new, overall weight: 14,400 kg, maximum load weight: 10,700 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 1,500 mm, Equipment: ABS, * KA-TA-R 14.4: * Front wall and floor hot-dip galvanized * Wabco ABS * Emergency release device for spring-loaded cylinder * Drum brakes * 2 x 7 to. Gigant axles Djbu Tl Dsp Ncmasxskl * Parabolic springs with tandem compensation unit * 300 mm height-adjustable hot-dip galvanized drawbar with 40 mm flanged drawbar eye * Jost mech. support winch at the front * 2 mechanical hot-dip galvanized folding supports at the rear * 15-pin power plug * Multi-chamber tail lights * hot-dip galvanized bolted underride guard * Tool box made of galvanized sheet steel on the right side * Plastic quarter mudguards * Hot-dip galvanized chassis * Steel Pal.- 3 side tipper body * continuous side walls in white on top with inner tube reinforcement without center stanchions - can be folded down with dropside spring lifter * Tailgate can be folded down and swivels via man. Central locking * Hot-dip galvanized bolted rear stanchions * 1 x 5 to. lashing ring in each corner Lashing ring in each corner and 4 x 3 to. lashing rings embedded in the outer frame * 4 mm sheet metal floor made of fine-grained steel * Net hooks, mounting rail at the rear for the feeder ramps * Preparation for later retrofitting of side wall attachments * Reinforced body with load securing certificate in accordance with EN 12642 XL * 1 pair of aluminum docking ramps approx. 3,570 x 400 mm (load capacity 8 to. / pair) suitable for rubber-tyred and tracked vehicles * Lockable storage compartment below the loading area recessed into the chassis from the rear * Axles, springs, air reservoir and support winch painted black * Side wall body color in 9010 pure white * 1 metre galvanized lattice extensions * Tires 285/70 R 19.5 * Sample pictures * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available from Egestorf on the A7

Condition: new, overall weight: 30,000 kg, maximum load weight: 23,500 kg, axle configuration: 3 axles, loading space length: 8,380 mm, loading space width: 2,520 mm, Year of construction: 2024, * PT 30 profile: * EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 tonne Gigant axles * Air suspension with lifting and lowering system and RtR valve * Smart board mounted on the trailer as an information tool (for axle load display - front and rear separately) * Tire pressure monitoring with display option in the truck via EBS signal without truck-side installation * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fender with splash guard * Rear straight galvanized. Sheet steel aprons with splash guard * Reflective contour tape on the side and rear * 15-pin power plug * LED lighting 12/24 V * LED rotating beacon (removable) at the rear * Pull scissors 1,200 mm long with 40 mm pull eye and height adjustment via tension spring & turnbuckle * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm, black powder-coated on the right side * Box in the bogie for accessories with hinged lid, 2 cont. locks permanently installed (directly after the bogie platform) * ROBOT welded ANTI-SLIP coating on the steel plate of the bogie platform (protruding weld beads) * La-Si package consisting of: 2 lashing eyes (13.4 tonnes) at the front left & right on the bulkhead support, front & rear 1 pair of UVV lashing rings (13.4 to.) and 3 pairs of UVV lashing rings (10 to.) on the side, swiveling and lowerable, loadable in all directions and embedded in the outer frame, 3 stake pockets on the side with simultaneous 2 ton lashing option * 6 pairs of mechanical folding booms for 3 m total width (but not in the rear slope) * Widening planks placed in the middle of the loading area * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm * Mechanically laterally adjustable * 4-way control block for later retrofitting of hydraulic. Ramp shift * Chassis, bogie, folding boom, drop supports and ramps hot-dip galvanized * Axles, slewing ring, air tank, drawbar painted in a black tone Djbu Tl Djrwc R Hexokl * Loading edge when loaded approx. 910 mm +/- 20 mm air suspension, * New vehicle with manufacturer's warranty * Errors and interim purchase subject to reservation * Available for immediate delivery from Egestorf

Condition: new, overall weight: 30,000 kg, maximum load weight: 24,100 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2024, * T3 profile 30.0: * EBS brake system * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles * Parabolic springs * Mechanical axle compensation at the rear * Lateral impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle closed plastic mudguard and rear axle straight galvanized. Steel sheet aprons each with splash guard * Reflective contour tape on the side and rear * Hinged lid (hot-dip galvanized) for the toolbox in the bogie platform * Multi-voltage system * LED tail lights * Rotating beacon (removable) at the rear * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * 15-pin power plug * 4 stanchion pockets on each side (but no stanchions available) with simultaneous lashing option * La-Si package consisting of: 2 lashing eyes (6.4 tons) at the front left & right on the main frame of the bogie platform, 5 pairs of UVV lashing rings that can be swiveled and lowered, can be loaded in all directions and are embedded in the outer frame - 13.4 tons in the corners, otherwise 10 tons * 6 pairs of mechanical folding booms for 3 mtr. Total width (but not in the rear slope) * Widening planks placed in the middle of the loading area * Excavator boom shelf above rear axle to the end beam approx. 2,100 mm long (2 pairs of 6.4 ton lashing rings on the side in the excavator boom shelf) * Hydraulic one-piece loading ramps (approx. 3,000 x 720 mm) laterally adjustable * Loading area above the turntable: approx. 1,960 x 2,520 mm * Loading height when unloaded approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Loading height when unloaded approx. 910 mm (incl. 860 mm approach slope) Dkjbu Tsl Th Adol Dxol * Chassis, bogie, scissors and loading ramps hot-dip galvanized * Axles, springs, air tanks etc. painted in a black tone * 235/75 R 17.5 twin tires * 5,900 kg empty weight * --total permissible weight of 30,000 kg technically possible-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * available immediately from Egestorf

Condition: new, overall weight: 30,000 kg, maximum load weight: 23,700 kg, axle configuration: 3 axles, Year of construction: 2024, * T3 Profi 30.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles * Air suspension with manual lowering at the rear * Pressure gauge pressure display for determining the load weight (axles separated into 2 air suspension circuits), * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle closed. Plastic fenders and rear straight galvanized sheet steel aprons, each with splash guard * Reflective contour tape on the side and rear * Hinged lid (hot-dip galvanized) for the toolbox in the bogie platform * LED tail lights * Rotating beacon (removable) at the rear * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * 2 x 7-pin power plugs * 4 stake pockets on each side with simultaneous 2 ton lashing option * La-Si package consisting of: 2 lashing eyes (6.4 ton) at the front left & right on the main frame of the bogie platform, 5 pairs of UVV lashing rings that can be swiveled and lowered, can be loaded in all directions and are embedded in the outer frame - 13.4 ton in the corners, otherwise 10 ton * 6 pairs of mechanical folding booms for 3 mtr. Total width (but not in the rear slope) * Widening planks placed in the middle of the loading area Dkjbu Tsl Tq Eujl Dxel * hydr. one-piece loading ramps (approx. 3,000 x 720 mm) laterally adjustable * Loading area above the turntable: approx. 1,960 x 2,520 mm * Loading height unloaded approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Loading height unloaded approx. 910 mm (incl. 860 mm approach slope) * Chassis, bogie, drawbar, folding extensions & loading ramps hot-dip galvanized * Axles, turntable, air tank etc. painted in a black tone * Tires 235/75 R 17.5 * Payload approx. 24,000 kg with 30,000 kg total weight * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, overall weight: 11,900 kg, maximum load weight: 8,780 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2024, * KA-TA-R 11.9 Masterline: * EBS, emergency release device for spring brake cylinders Dsbu Topk D D Uol Dxjkl * RDÜ tire pressure monitoring * Drum brakes * 2 x 5.5 to. BPW axles * Parabolic springs with tandem compensation unit * 300 mm height-adjustable hot-dip galvanized drawbar with 40 mm flanged drawbar eye * Jost mech. support winch at the front * 2 mechanical hot-dip galvanized folding supports at the rear * Tool box made of galvanized sheet steel on the right side * 15-pin power plug * Bolted underride guard with LED tail lights * Plastic quarter mudguards * Mesh hooks at the side and rear in the bearings of the central locking system and 3 pieces on the outside of the bulkhead * Hot-dip galvanized chassis * Fully galvanized steel Pal. 3 side tipper body * Full-length side walls without central stanchion can be folded down with dropside spring lifter * Tailgate can be folded down and swung down via man. Central locking * Hot-dip galvanized bolted rear stanchion * 1 x 5 to. lashing ring in each corner Lashing ring recessed and foldable in each corner and 4 x 3 to. lashing rings recessed in the outer frame and hinged * 4 mm sheet steel floor, rear mounting rail for feeder ramps * Reinforced body with load securing certificate in accordance with EN 12642 XL * 1 pair of aluminum docking ramps approx. 3,570 x 400 mm (load capacity 8 to. / pair) suitable for rubber-tyred and tracked vehicles * Storage compartment lockable from the rear under the loading area recessed in the chassis * 235/75 R 17.5 tires * Axles, springs, air reservoir, drawbar and support winch painted black * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available immediately from Egestorf on the A7