Open semitrailer with tarp

MAX Trailer 3-Achs-Jumbo-Semi-Rampen-Planenaufbau

Condition: new, empty load weight: 11,000 kg, maximum load weight: 27,000 kg, overall weight: 38,000 kg, axle configuration: 2 axles, loading space length: 7,300 mm, loading space width: 2,550 mm, tire size: 235/75 R17.5, color: grey, operation weight: 11,000 kg, Equipment: ABS, Chassis: - Steel frame welded construction with front and rear frame extensions and a low-bed without a rear slope - Frame neck + kingpin plate 225 mm - Low-bed designed for a point load of 25 tons over 5 m - Outer frame closed on the outside with welded lashing rings for securing cargo - Interchangeable 2" kingpin - Rear mounting rail for aluminum ramps Axles and Tires: - BPW low-loader axles, 10 tons axle load each, air spring diameter 360 mm - Air suspension with lifting and lowering device, stroke 220 mm (-60/+160 mm) - Wabco SmartBoard with ECAS function for 2 coupling heights + 100 mm - S-cam brake 300/200 mm, asbestos-free brake linings - Automatic slack adjusters - IVTM tire pressure monitoring system - 9 tires 235/75 R 17.5, tubeless Steering: - 1st and 2nd axles hydraulically steered via the fifth wheel coupling Floor: - Multi-layer glued panel floor with a thickness of 27 mm, flush with the outer frame and longitudinal beams - Reinforced underneath with GRP coating - 12 pairs of lashing rings welded into the outer frame (8 pairs RUD 8 tons – 6 pairs in the low-bed and one pair each on the gooseneck and at the front of the rear section – 2 pairs of lashing rings 4 tons on the gooseneck and rear section) - 6 pairs of mushroom-shaped load securing points in the outer frame in the low-bed - Storage compartment with lid in the floor of the low-bed, front left and right Front Wall: - 25 mm aluminum hollow profiles extending up to the lower edge of the roof with integrated tarpaulin tensioning device Sliding Tarpaulins: - Sliding tarpaulins on both sides with welded vertical and horizontal straps (spacing approx. 600 mm) and stainless steel tensioning closures - Adjustable tarpaulin straps (over center) up to a loading width of 4,000 mm, including tarpaulin extension with snap buttons and Velcro - Tarpaulin extension in the direction of travel: 300 mm, in height: 750 mm - Incl. eyelets for a loose tarpaulin extension part - 1 pair of vertical tarpaulin pockets with a length of approx. 1,000 mm, position in the low-bed at the front extension - With strap pockets Rear Wall: - Steel rear portal frame with lateral tarpaulin mounting device - Aluminum double-wing door, 25 mm thick - Both door wings can be fully folded in with door latch - One aluminum double-hinge hinge and two recessed handle recesses per door wing Front Corner Posts: - At roof height, screwed on at the front end Intermediate Posts: - 3 pairs of steplessly adjustable folding posts - The posts can be moved along the entire length using roller carriages - Intermediate posts can also be fixed in the rear platform in the low-bed Roof: - EDSCHA sliding tarpaulin (galvanized) with crossmember that can be moved in both directions (pushed forward together in the loading area) - Rear portal crossbar can be swung out - PVC tarpaulin roof without customs closure - Manually hydraulic lifting roof on both sides, stroke 450 mm - Lifting roof can be operated in the front (9x50) and rear (9x50) elevated positions Podpsiu Eu Njfx Adhsrb - Including tarpaulin extension and tarpaulin rail at the rear - Tarpaulin can be extended by 900 mm at the front end wall Accessories: - Extendable warning signs (removable at the rear and front with socket) incl. position lights up to a loading width of 4,000 mm - Storage of the 4 warning signs on the front wall, inside, top right and left - 1 aluminum ladder with bracket 2,500 mm long on the front wall - 2 rows of aluminum slats self-locking - Sheet metal mudguard

Condition: new, maximum load weight: 38,100 kg, overall weight: 50,000 kg, axle configuration: > 3 axles, loading space length: 13,100 mm, loading space width: 2,480 mm, loading space height: 760 mm, suspension: air, tire size: 205/65 R17.5 3PMSF, color: grey, Equipment: ABS, Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10° 3 pairs of lashing rings Hardwood decking 30 mm thick Loading area: 5 pairs of lashing rings can be folded outwards 3 pairs of lashing rings can be folded outwards 1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Seat posts: JOST seat posts with 2-speed gearbox for 24 t lifting capacity Axles and tires: BPW axles, two axles rigid two axles self-steering, air-sprung, with drum brake, with raise/lower function The self-steering axles with electromagnetic reverse lock can be activated via reverse gear or manually Axle tool Tires 205/65 R17.5 3PMSF Brake system: WABCO brake system in accordance with EU regulations with EBS-E Steel construction: Steel construction made from high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Electrical equipment: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO Paintwork: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component zinc dust primer A high-quality 2-component Top coat single color in MB 7350 nova grey No metallic paint finish possible Rear section metallized and painted in RAL 9010 Accessories included: 1 spare wheel 205/65 R 17.5 TPMS tire pressure monitoring system in accordance with ECE R 141 Yellow-red air couplings on the galvanized connection strip at the front 4 brake shoes with holder on the bulkhead Mounting in the rear area of the gooseneck for ALU docking lights Galvanized folding supports under the bevel of the cargo bed A holder for a rotating beacon at the rear of the trailer Height-adjustable tarpaulin body Galvanized bulkhead with a tensioning mechanism for the sliding curtains Height-adjustable by approx. 400 mm "EDSCHA" brand roof can be moved forwards on ALU roof rail profiles bolted to the front and rear wall 3 pairs of sliding stanchions in the loading area The body can be hydraulically widened at the rear to the left and right by approx. 750 mm Sliding roof with pivoting portal support Sliding tarpaulin with 700 mm reserve in length, with tension belts at approx. 600 mm intervals Height top edge of body approx. 3,960 mm Driving with the sliding tarpaulin open is not permitted and will damage the tarpaulin Suspension strip for ALU docking lights at the rear of the vehicle A holder for the warning signs including socket on the gooseneck and on the rear panel on the left and right respectively A mud flap at the rear of the trailer European reflector plates at the rear of the trailer 7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load condition Rear body closed with ALU hinged doors A layer of sand painted onto the chequer plates on the gooseneck and on the cargo bed to prevent slipping Psdpstphtmsfx Adhsrb BEKAMAX central lubrication system with NLGI-2 standard grease and removable protection around the pump Speed sticker 80 km/h at the rear and on both sides Load manometer to determine the axle loads including load diagram

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 11,000 kg, maximum load weight: 27,000 kg, overall weight: 38,000 kg, axle configuration: 3 axles, loading space length: 9,500 mm, loading space width: 2,480 mm, loading space height: 3,040 mm, total length: 13,800 mm, total width: 2,550 mm, total height: 4,020 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Chassis Steel welded construction with narrow crossmember spacing and reinforced design, low-loader outer frame profile, for transporting construction machinery up to 32,000 kg and with a maximum outer width of the construction machinery of 2550 mm, kingpin plate with replaceable 2 kingpins. Rear slope of approx. 1200 mm and 7°. Ramp shaft closed at the top with steel/diamond plate, in the low-bed, omega rail laterally at the bottom on the outer frame as a mounting rail for tarpaulin and spacers for lashing points, not in the wheel area. If a lift table is used, there is an additional, lightweight outer frame with an omega profile. 24-ton, 2-speed landing gear, single-sided operation, with a semi-circular lower part and a straight connection plate, with stroke compensation, free swivel radius to the rear approx.: 1950 mm, rear support, foldable 2 wheel chocks + holder Side underrun protection, aluminum Quarter panel fenders in front of and behind each axle with anti-splash flaps behind each axle Underrun protection, steel Splash flap at the rear over the entire width 4 storage boxes, stainless steel, w=800/h=350/d=350 mm, with a polished, lockable door, 2 x on the left front and 2 x on the right front in front of the 1st axle Lift table behind the gooseneck, approx. 3000 mm long, hydraulically liftable for crossing over the gooseneck, with mechanical locking in the raised position. (Cylinder angled for good ground clearance, Fliegl standard). Operation on the right front + additional activation with a wireless remote control, lift table can be raised with the tarpaulin closed! Tarpaulin attachment in the lift table area to an additional, lightweight outer frame with omega profile, lift table can be raised with the tarpaulin closed! Lashing points can also be used in the lowered position! Lashing points Gooseneck: 4 pairs of 5-ton lashing points embedded in the outer frame 2 pairs of lashing points at the top and on the side embedded in the outer frame 8 pairs of lashing points at the top and on the side embedded in the outer frame, each 10 tons Psdpsi Riw Asfx Adhjrb 9 pairs of 5-ton lashing points embedded in the outer frame Axles + Suspension SAF drum brake axles last axle with trailing steering knuckle, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lifting and lowering valve + auto-reset function H&S function with quick vent 1st axle, automatic lift axle, incl. forced lowering and starting assist, activated by pressing the brake pedal 3 times (starting assist is functional up to an axle load exceedance of 30% and a speed of max. 25 km/h) Axle lift below the recommended ride height, no guarantee for tire damage Wheels and tires 235/75R17.5 from leading manufacturers Steel rims in twin arrangement, factory silver Braking system 2-line pneumatic braking system Spring brake parking brake 2 foolproof coupling heads at the front EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Axle load recognition in the truck via EBS, without installation in the truck. Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white

Condition: new, empty load weight: 10,350 kg, maximum load weight: 39,150 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with rear slope of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood deck, 30 mm thick Loading platform: -Telescoping loading platform with rear slope of approx. 1,000 mm x 8° -1 pair of permanently installed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm -Wheel recesses with square climbing strips 15 x 15 mm and widening in the lower area -Between the 1st and 2nd axles, a pair of permanently installed wheel recesses, approx. 1,610 x 970 x 400 mm -3-part removable galvanized covers over the wheel recesses (W 670 mm) - max. point load 5 tons / piece -Recess in the slope and extending into the loading platform to accommodate the excavator arm, approx. 2,900 x 750 x 210/290 mm -1 pair of lashing rings lying at the front in the loading platform (LC 10,000 daN) -5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) -2 pairs of lashing rings that can be folded outwards (LC 10,000 daN) -2 pairs of lashing rings in the excavator arm recess (LC 5,000 daN) Prodeiu Er Aopfx Adhob -Cutouts in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) One-piece aluminum ramps: -A pair of one-piece aluminum ramps, approx. 2,500 x 600 mm -Ramp with spring lift mechanism and manually adjustable -Maximum load per pair: 24,000 kg Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle steered -Technical axle load: 12,000 kg -Electromagnetic reversing lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -Axle tool -Tires 235/75 R 17.5 -TPMS tire pressure monitoring system according to ECE R 141 Included accessories: -One spare wheel with holder in front of the front wall -2" kingpin -One galvanized steel front wall, approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 pieces of wheel chocks with holder on the front wall -Mounting in the rear area of the gooseneck for aluminum ramps -Widening, galvanized, extendable by approx. 230 mm on each side -Galvanized folding supports under the slope of the loading platform -One mounting for a rotating beacon on the rear of the trailer -White reflector tape according to EU regulations on the side, on the extension and red at the rear -On the gooseneck and on the rear panel, one mounting each on the left and right for warning signs including socket -On the gooseneck, aluminum side and rear panels that can be plugged in, approx. 2,440 x 400 mm -The rear galvanized slotting strips are removable (length of the structure approx. 2,560 mm) -2 pairs of WADER container pockets in the loading platform for a 20ft or 30ft container -3 pairs of rung pockets for slotting strips 100 x 50 mm in the outer frame of the loading platform -One removable galvanized intermediate table with 1 pair of WADER container pockets -Square climbing strips 20 x 20 mm every 200 mm on the outer frame of the slope of the loading platform -A sand coating is applied to the diamond-patterned plates on the gooseneck and on the loading platform for slip resistance -Four warning signs, each extendable by approx. 400 mm, approx. 423 x 423 mm, with a position light -On the warning signs, a mounting for a rotating beacon -Speed sticker 80 km/h at the rear and on both sides -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel structure shot blasted, then the defined visible sur

Condition: new, empty load weight: 12,300 kg, maximum load weight: 37,200 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,480 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -Hardwood covering 30 mm thick Two-piece steel ramps: -A pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating covering -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear -Maximum load per pair: 30,000 kg Loading area: -Loading surface with rear slope of approx. 1,000 mm x 8° -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Axles and tires: -BPW axles and suspension, two axles rigid, one axle self-steering -Air suspension with lifting and lowering valve The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -235/75 R17.5 3PMSF tires Accessories included: -1 Spare wheel with holder -TPMS tire pressure monitoring system according to ECE R 141 -2" kingpin -Galvanized steel bulkhead -Yellow-red air couplings on the galvanized front connecting strip -4 restraining shoes with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -3 height aluminum boards -Galvanized folding supports under the bevel of the cargo bed Height-adjustable tarpaulin superstructure (3,960 mm) -Galvanized bulkhead with a tensioning mechanism for the sliding curtain -Height-adjustable by approx. 400 mm -"EDSCHA" brand roof can be moved forwards on ALU roof rail profiles bolted to the front and rear wall -3 pairs of sliding stanchions in the loading area -The body can be hydraulically widened at the rear to the left and right by approx. 750 mm -Sliding roof with pivoting portal support -Sliding tarpaulin with 700 mm reserve in length, with tension belts at approx. 600 mm intervals -Height top edge of body approx. 3,960 mm -Driving with the sliding tarpaulin open is not permitted and will damage the tarpaulin -Cover plates to bridge the free space between ramps and loading area -Electric hydraulic unit at the rear, under the cargo bed Prsdjtvfkfepfx Adhjb -On the gooseneck and on the ramps on the left and right, one bracket each for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Lift axle on the front axle -Grating in the bevel of the loading area C40/4 (point load 3.4 tons on an area of 20 x 20 cm) -One INOX toolbox 565 x 290 x 810 mm in the direction of travel on the right between the axles -A layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, maximum load weight: 34,104 kg, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Further information here: Prjdpev D Abgofx Adheb

Condition: new, empty load weight: 12,800 kg, maximum load weight: 36,200 kg, overall weight: 49,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,550 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 12,800 kg, Equipment: ABS, Gooseneck: - Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm - Gooseneck hydraulically raised/lowered and removable - Technical fifth wheel load: 25,000 kg - For tractor units: 4 x 2, 6 x 2, and 6 x 4 Loading area: - Low bed with external supports, designed as a telescopic tank bridge in a low construction with a front extension - Length 6,850 mm x Width 2,540 mm - One locking point approximately every 1,000 mm on the extension Rear chassis: - Rear chassis with closed outer frame with checker plate cover and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear Axles, suspension, and tires: - "PENDEL-AXLE", all Hydro-mechanically forced-steered axles - Hose rupture valve on the axle balancing cylinder with automatic reset function - Hydraulic cylinder with shut-off valves and pins for securing in the raised position - Final axle painting with two coats of 2-component acrylic paint in a single color "FAY-Gray-34-0260" - Technical axle load: 12,000 kg - Hydraulic axle balancing - Tires: 245/70 R 17.5 - TPMS tire pressure monitoring system in accordance with ECE R 14 - TPMS tire pressure monitoring sensors installed in all wheels, including spare tires Accessories included: - Steel bulkhead, plug-in, approx. 400 mm high - 3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches - One spare tire with mounting adapter - Gooseneck outer support with mounting holes for screwable lashing rings -Slidable aluminum side walls on the gooseneck, approx. 400 mm high, anodized -Slidable aluminum rear wall on the gooseneck, approx. 400 mm high, anodized -Checker plate covering above the gooseneck -Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide -Illuminated control panel on the gooseneck with on/off switch -Hydraulic crossbar for supporting the gooseneck on the tractor unit or a dolly -2" kingpin -Anti-slip sticker on the left slope of the gooseneck -Gooseneck closed at the rear upper area with a removable cover -4 chocks with brackets -Hydraulic connections from the gooseneck to the drop bed with multi-coupling instead of screw couplings -1 pair of steel ramps with climbing rails and fastening bolts for bridging the drop bed's hooks -The Ramps can be installed over or between the hooks. -Attachment option for the steel loading ramps at the rear between the outer supports of the gooseneck. Prsdpfx Adevy Edcehob -Prepared for screw-on container holders for 1x20f on the outer support. -Mechanical bolt-and-lug coupling from the low bed to the chassis, for replacing the loading area or installing extension supports. -With electro-pneumatic-hydraulic couplings. -The outer supports of the low bed are provided with a painted layer of sand as a slip protection. -Removable loading floor (galvanized) in 3 elements, insertable between the outer supports with hardwood flooring. -Foldable extensions, by approximately 230 mm per side. -Hanging rail at the front of the rear chassis to the low bed for loose loading ramps. -2 pairs of stake pockets recessed into the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm. -Hanging rail for loose Aluminum docking ramps on the vehicle's end crossbar -Central lubrication system with 2 pumps -Wireless and cable remote control -4 warning signs, approximately 423 mm x 423 mm extendable -Extensive lashing positions

Condition: used, maximum load weight: 31,710 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 10/2016, next inspection (TÜV): 04/2027, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. The following is an excerpt of the equipment. Complete equipment list available upon request. Chassis with wedge-shaped design. Increased point load of approximately 25,000 kg over approximately 5,000 mm. 24,000 kg telescopic support winches with load and fast-speed settings. Lashing points in 5,000 kg, 6,000 kg, and 10,000 kg versions. 8 stake pockets (for 2 front walls). Aluminum roof rail with sliding cover. Rear stakes extendable to approximately 3,500 mm, for loading and unloading purposes only. Three sliding stakes per side. End stakes extendable laterally in the direction of travel. Front wall designed as a storage area with integrated shelving system, closed on the inside. DINKEL lift roof, mechanically adjustable in height, lift roof height 400 mm, operable on both sides or on one side. Additional height adjustment of 480 mm in 40 mm increments (12 x 40 mm) with height adjustment in the stakes. Trailer can be driven under tarpaulin up to a total height of approximately 4,400 mm (open at the rear above the loading platform). Upper portal crossbeam with sliding cover, movable. Four rows of stackable 150 mm aluminum slats on the side (only 2 rows of slats in the upper bunk), 450 mm pockets at the bottom, 4 rows of pockets above, even spacing between them. WABCO air brake system with EBS according to EC standard 71/320 EEC including PREV. Air suspension in ECAS version, with lifting and lowering function. Wabco Smart Board with engine load display and lift odometer. 3 x 10,000 kg SAF axles with drum brakes. 3rd axle as a friction-jointed trailing axle. 1st axle can be lifted. Tires 235/75 R 17.5. Dhollandia heavy-duty lift platform type DHLSU, load capacity 9,000 kg, load distance 1,000 mm, steel platform approximately 3,000 x 2,500 mm. Hydraulic additional support, automatic ground leveling. Loading platform with ramp function for inclining the platform, for use as a drive-up ramp, loadable up to a maximum of 13,500 kg. Chassis painted in mb-novagrau. Body painted white. Tarpaulins with customer lettering! Prjdpfey Dy Ehex Adhsb

Condition: used, maximum load weight: 31,000 kg, overall weight: 45,000 kg, axle configuration: 2 axles, first registration: 06/2026, next inspection (TÜV): 06/2027, loading space width: 2,550 mm, loading space height: 300 mm, total width: 2,550 mm, total height: 300 mm, Year of construction: 2026, Equipment: ABS, DOLL tera 2-axle low-bed semi-trailer with trailing axles New vehicle, first registration June 30, 2026 Unladen weight 13,950 kg Permissible total weight (technical) 45,000 kg Gooseneck length 3,070 mm Saddle height 1,200 to 1,280 mm Swivel radius 2,350 mm Low-bed length 6,800 mm Telescopic extension length 5,700 mm Rear axle bogie length 2,700 mm Width of excavator arm recess 700 mm Depth of excavator arm recess 550 mm Loading height of low-bed 300 mm Loading height above the chassis 955 mm Width of the semi-trailer 2,550 mm Hydraulic suspension -70 / + 530 mm Technical maximum saddle load 21,000 kg Axle load 24,000 kg Detachable gooseneck with external main frame Painting of the semi-trailer in 3 layers including hot-dip galvanizing Doll Tronic CAN-bus system Podpfozmqmxsx Adherb Floor in the low-bed: 45 mm spruce wood planks between the flatbed frames 24-volt E-hydraulic system Control of trailer functions with DOLL keypads on the gooseneck AUXILIARY STEERING with REMOTE CONTROL EEG electronic single-lane guidance during straight-line driving LaSi in the low-bed: 7 pairs of swivelable lashing points, 13,400 daN lashing force 5 pairs of frame pockets in the outer frame 3 pairs of M36 threads externally for screwing in lashing brackets DOLL tera chassis with trailing axles and hydraulically suspended BPW axles All axles are hydraulically steered with a maximum steering angle of 60° on the last axle All lubrication points are connected to the central lubrication system WABCO trailer EBS with ABS and RSS Aluminum air tank BEKA-MAX central lubrication system on the front and rear units Overwidth package with foldable loading area extensions 2x 225 mm, extendable warning sign package up to 3,200 mm width Tires 8x 245/70 R 17.5 RENTING is the new BUYING, with us, also available in full-service rental IMMEDIATELY-----

Condition: new, maximum load weight: 36,020 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our full vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Complete equipment details available on request. Gooseneck: * Gooseneck with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area with rear bevel approx. 1,000 mm x 8° * 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) * 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate above the axles Two-piece steel ramps: * One pair of galvanized two-piece steel ramps, approx. 3,185 + 1,420 x 1,250 mm, with grating covering C40/5 (point load approx. 2.8 t on a surface of approx. 20 x 20 cm) * Ramp with hydraulically foldable ramp sections and hydraulic lifting system * Maximum load per pair: 30,000 kg Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 steering trailing axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock activated via reverse gear and manually * Air suspension with raise/lower valve Tyres: * Tyres 235/75 R 17.5 3PMSF – brand at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Predey Auhujpfx Adheb Brake system: * WABCO brake system compliant with EU regulations, with EBS-E (2S2M), without connection lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations, LED lighting 24V ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * HRM metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to guarantee optimum corrosion protection * Finishing coat: 2 layers 2K topcoat, solid colour RAL 3002 carmine red as per RAL system 841GL * Rear section metallised and painted RAL 9010 (pure white) * Rims in silver Included accessories: * One bracket for warning signs on the gooseneck and at the rear left and right, including socket * 1 spare wheel holder under the loading area, right in the direction of travel * 2" kingpin * One galvanized steel front wall * Yellow-red air couplings on the galvanized front connection bar * 4 wheel chocks with brackets on the bulkhead * 3 height wooden boards * Galvanized folding supports under the loading area bevel * Bracket for rotating beacon at rear of trailer * Height-adjustable tarpaulin structure – approx. 3,960 mm * Galvanized front wall with tensioning system for sliding curtains, height adjustable by approx. 400 mm * EDSCHA roof, sliding forward on aluminum roof girder profiles (screwed to front and rear wall) * 3 pairs of sliding stakes in the loading area * The body is hydraulically extendable to the left and right at the rear by approx. 750 mm * Sliding roof with pivoting portal crossbeam * Sliding curtain with approx. 700 mm reserve length, ratchet straps at approx. 600 mm intervals. Height O