Low loader semitrailer

Faymonville 4-1+3-Achs-Tele-Semi-Radmulden-Rampen-zg

Condition: new, empty load weight: 15,550 kg, maximum load weight: 47,450 kg, overall weight: 63,000 kg, axle configuration: 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm -Rear gooseneck with bevel approx. 1,000 mm x 10° Loading area: -Loading area in extendable design, length approx. 8,800 mm, with bevel at the rear approx. 500 mm x 10° -One recess protruding into the loading surface and into the chamfer to accommodate the excavator dipper arm -Pneumatic locking with conical locking pins and reinforced locking positions -Hardwood covering on the bevel of the loading area Ramps: -1 Pair of two-part steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm -Ramps with hardwood decking -Hydraulically folding ramp tips -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards -Square climbing ledges 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and suspension: -BPW axles and suspension, 1st axle with preload steering, all other axles with forced hydromechanical steering -Technical axle load: 12,000 kg -1st axle with electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -235/75 R 17.5 twin tires -TPMS tire monitoring system in accordance with ECE R141 -TPMS tire monitoring sensors mounted in all wheels including spare wheels Accessories included: -steel front wall, pluggable, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Parking position on the gooseneck for the warning signs when not in use -1 Spare wheel -On the gooseneck 1 pair of plug-in ALU side panels, approx. 400 mm high, anodized -One plug-in ALU rear panel on the gooseneck, approx. 400 mm high, anodized -Approx. 40 mm thick hardwood covering over the gooseneck, checker plate covering over the kingpin -2" kingpin -Guide plate from the gooseneck for the saddle plate, approx. 500 mm wide -4 wheel chocks -Mechanical seat posts with 2-speed gearbox and crank -JOST module B - static test load = 50,000 kg -1 Intermediate table, approx. 300 mm wide -Widenings (galvanized) extendable by approx. 230 mm per side -Wheel recesses with square climbing rails -ALU covers for the wheel recesses Kdodjk Aht Uspfx Ak Nsk -1 pair of mechanical rear supports -Steering can be operated from the front and rear by cable remote control, with tracking control of the axles -1st axle with automatic lift axle function -Central lubrication system with 1 pump, BEKAMAX brand -Radio remote control for operating the self-steering, in addition to the cable remote control, with 2 indicator lights on the receiver as toe-in control -Wabco Smart Board System -4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for rotating beacon

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions Kdsdotx Nwnopfx Ak Nok * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: new, empty load weight: 22,700 kg, maximum load weight: 79,300 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, loading space length: 11,000 mm, loading space width: 2,850 mm, loading space height: 920 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 22,700 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the length of the loading area, length approx. 3,750 mm, with a bevel at the rear of approx. 850 mm x 10° -Can be raised and lowered hydraulically, stroke +- 250 mm including hydraulic connection connected to the hydraulic axle compensation of the first two axles -Open in the rear third -For tractor units: 6 x 4 and 8 x 4 Loading area: -Loading area in extendable design, length approx. 11,000 mm with a bevel at the rear of approx. 500 mm x 10°. Kedsk Af Svopfx Ak Nedk -A recess in the loading area and in the bevel to accommodate the excavator bucket handle approx. 4,240 x 900 x 440 mm -Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable supports and automatically adjust to the respective loading area length Ramps: -A pair of two-part steel ramps with a length of approx. 4,650 mm and a width of approx. 900 mm -Hydraulically foldable ramp tips. -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards -25 mm "Super Grip" rubber floor and approx. 5 mm sheet metal floor as additional reinforcement on the slope of the loading area -20x30 mm square climbing rails, approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: -PA-X axle system, all axles hydro-mechanically forced steered -The steering behavior of the first two axles can be optimally adjusted to the length of the loading area both mechanically and hydraulically. -Hose rupture valve on the axle compensation cylinder with automatic RESET function. -Hydraulic cylinder with shut-off valves and pins for securing in the raised position. -245/70 R 17.5 3PMSF Accessories included: -Steel bulkhead, pluggable, approx. 400 mm high -Connection strip for supply lines to the tractor unit, mounted at the height of the outer frame profile -1 spare wheel -Outer support of the gooseneck with mounting holes for screwable lashing rings -The first hole approx. 200 mm from the front, then approx. every 400 mm -2 pairs of screwable lashing rings included -Checker plate covering above the gooseneck -On the gooseneck 1 pair of pluggable aluminum side walls on the side, approx. 400 mm high, anodized -On the gooseneck a pluggable aluminum rear wall, approx. 400 mm high, anodized -3.5" kingpin / 2" kingpin mounted -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -4 Brake shoes -4 axle load gauges -Mechanical downpipe supports at the front -1 one-piece INOX tool box, approx. 2,480 x 340 x 390 mm -Mechanical downpipe supports at the front -Continuous sheet metal covering on the loading area with a painted layer of sand to prevent slipping -1 intermediate table, approx. 500 mm wide, for the pull-out, with long holes for hanging and movable bridging elements -Painted sand coating on the support surfaces of the intermediate table -Mechanical locking for locking the intermediate table to the pull-out -8 pairs of stake pockets in the outer frame -Extensions (galvanized) extendable by approx. 230 mm per side -1 pair of hydraulic. Rear supports -Central lubrication system -1 reversing light on the left and right at the rear of the vehicle -3 kW electro-hydraulic unit -Widening planks, loose, in reinforced steel U-frame -Radio and cable remote control -4 warning signs, approx. 423 x 423 mm

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches Kdsdpforgzv Nox Ak Nsk * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: used, power: 70 kW (95.17 HP), fuel type: diesel, color: red, lifting height: 9,000 mm, tire size: 15.5 / 80 - 24, tire condition: 98 %, mast type: telescopic, Year of construction: 2009, operating hours: 2,362 h, load capacity: 3,200 kg, Equipment: all wheel drive, cabin, hydraulics, pallet forks, Off-road - MANITOU telescopic arm forklift, type: MT 932 D-E3 - 4x4x4, first use: 2010, LIFTING FORCE: 3,200 kg, LIFTING HEIGHT: 9.00 m, LONG LOADING FORKS (fork length: 1.180 mm / pick-up width: 1,120 mm) - LOAD PROTECTION GRID, ADDITIONAL HYDRAULIC, QUICK CHANGER, 4-cylinder PERKINS TURBO diesel engine (type: 2978/2200 - 95.20 hp / 70.00 kW at 2.200 rpm), ALL-WHEEL and ALL-WHEEL STEERING (4x4x4) - DOG DRIVING, OVERLOAD WARNING DEVICE, large cab (low overall height, only approx. 2,280 mm) - colored glass, comfort seat, ROPS / FOPS, trailer coupling (with power connection), traffic lights, CPB, WARNING LIGHTS, exterior mirrors (2x), windscreen wipers (2x), heating / ventilation, retaining and transport eyes, OPERATING INSTRUCTIONS (in German). Tires: All-terrain tires (15.5 / 80 - 24) - approx. 98 % all-round. Transport dimensions: Length: approx. 5,850 mm (approx. 4,600 mm without forks), width: approx. 2,280 mm, height: approx. 2,280 mm. Price is net export, plus VAT in Germany. ∗∗∗ FINANCING POSSIBLE / TRANSPORT AFFORDABLE (WORLDWIDE) / ON EXPORT ONLY THE NET PRICE IS TO BE PAID (!) ∗∗∗∗ © pb - - - - - - - - - - - - - Rough terrain telescopic forklift MANITOU, type: MT 932 D-E3 - 4x4x4, first use: 2010, LIFTING FORCE: 3.200 kg, LIFTING HEIGHT: 9.00 m, LONG FORKS (forklength: 1.180 mm / width admission: 1.120 mm) - PROTECTION LOAD GUARD, ADDITIONAL HYDRAULIC, QUICK CHANGER, 4-cylinder PERKINS TURBO diesel-engine (type: 2978/2200 - 95.20 PS / 70.00 kW at 2.200 rpm), 4-WHEEL-DRIVE (4WD) and ALL-WHEEL-STEERING SYSTEM (4x4x4) - CRAB STEERING (dogway), OVERLOAD PROTECTION SYSTEM, big driverhouse (low height, only approx. 2.280 mm) - colorglass, comfortseat, ROPS / FOPS, follower coupling (with power connection), road lightnings, CPB, WARNING LIGHT, back view mirror (2x), windshield wiper (2x), heating / ventilation, hold- and transporthooks, OPERATION MANUAL (in german). Tyres: ROUGH TERRAIN TYRES (15.5 / 80 - 24) - all around approx. 98 %. Transport dimensions: see above. Price is net. ∗∗∗ EQUIPMENT IS FINANCEABLE in nearly all european countries / TRANSPORTATION WORLDWIDE POSSIBLE at good conditions / EXPORT: ONLY THE NET AMOUNT NEEDED TO PAID (!) ∗∗∗∗ © pb Kjdpfx Akeuq Hypo Nsdk

Condition: used, Year of construction: 2014, load capacity: 5,000 kg, lifting height: 21,000 mm, fuel type: diesel, construction height: 3,050 mm, tire condition: 50 %, front tire size: 18 R22.5, rear tire size: 18 R22.5, color: other, Special equipment: 3rd valve, heating, full cab, special equipment description: overhead guard, 3rd control circuit, lighting, radio control, joystick Kodpfx Akei Rhtvs Nsdk

Condition: new, maximum load weight: 65,400 kg, overall weight: 93,400 kg, axle configuration: > 3 axles, Year of construction: 2025, Pos 1. Type STZ-VP 6 (245) (2+4) with pendle axles The specified technical data are only valid when used with a 4-axle tractor unit with the following specifications: Dimension a: 5,400 mm Saddle height (loaded): 1,300 mm Weights Speed: 80 km/h - Fifth wheel load: 22,000 kg - Axle load: 6 x 12,000 kg - Permissible total weight: 94,000 kg - Tare weight approx.: 29,600 kg - Payload approx.: 64,400 kg (depending on load chart / easyLOAD calculation) Dimensions - Dimension b: 18,765 mm - Overall train length: 24,165 mm - Vehicle width: (please specify) - Gooseneck length x width: 3,700 mm x 2,480 mm - Saddle height (loaded): 1,300 mm - Steering lock radius front/rear: 1,370 mm / 2,735 mm - King pin: 3.5'' Kdedpfx Aswg N N Iek Nok Front 2-axle chassis - Wheelbase: 1,510 mm - Single tires: Continental, 245/70 R 17.5 143/141 L (146/146 F) M+S - Steering axle arrangement: counter-steered 14,400 mm flatbed (outer beams) single extendable with split - Length x width: 7,000 mm x 2,750 mm - Extendable by / to max.: 3,400 mm / 10,400 mm - Deck height: 300 mm - Plus 4,000 mm extension beam incl. - Loading height, loaded: approx. 450 mm Rear 4-axle chassis - Wheelbase: 3 x 1,510 mm - Single tires: Continental, 245/70 R 17.5 143/141 L (146/146 F) M+S - Steering axle arrangement: forced steering

Condition: used, power: 74.5 kW (101.29 HP), fuel type: diesel, color: red, lifting power: 4 kg/m, lifting height: 14,000 mm, tire size: 15.5 / 80 - 24, tire condition: 98 %, mast type: telescopic, Year of construction: 2007, operating hours: 1,048 h, Equipment: all wheel drive, cabin, pallet forks, Off-road - telescopic arm forklift MANITOU, type: MT 1440 SLT ULTRA TURBO Series III-E2 - 4x4x4, first use: 2008, LIFTING FORCE: 4,000 kg, LIFTING HEIGHT: 14.00 m, LONG LOADING FORKS - QUICK CHANGER, ADDITIONAL HYDRAULIC, LOAD PROTECTION GRID, 4-cylinder PERKINS TURBO-Diesel engine (101.32 HP / 74.50 kW at 2.200 rpm), RADIO REMOTE CONTROL, ALL-WHEEL and ALL-WHEEL STEERING (4x4x4) - DOG DRIVING, hydraulic outriggers (2x / WIDE), SIDE-BALANCE CONTROL, CPB, OVERLOAD WARNING DEVICE, large driver's cab (colored glass), KAB - comfort seat, ROPS / FOPS, traffic lights, WORKING LIGHTS (front/rear), WARNING LIGHTS, exterior mirrors (2x), windshield wipers (2x), heating / ventilation, trailer coupling, retaining and transport eyes. Tires: BKT OFF-ROAD TIRES (15.5/80 - 24) - approx. 98 % all-round. Transport dimensions: Length: approx. 7,290 mm (approx. 5,930 mm without fork), width: approx. 2,440 mm, height: approx. 2,560 mm. Price is net export, plus VAT in Germany. ∗∗∗ FINANCING POSSIBLE / TRANSPORT FAVORABLE (WORLDWIDE) / FOR EXPORT ONLY THE NET PRICE IS TO BE PAID (!) ∗∗∗∗ © pb - - - - - - - - - - Rough terrain telescopic forklift MANITOU, type: MT 1440 SLT TURBO ULTRA Serie III-E2 - 4x4x4, first use: 2008, LIFTING FORCE: 4.000 kg, LIFTING HEIGHT: 14.00 m, LONG FORKS - QUICKCHANGER, ADDITIONAL HYDRAULIC, PROTECTION LOAD GUARD, 4-cylinder PERKINS TURBO-diesel engine (101.32 PS / 74.50 kW at 2.200 rpm), REMOTE CONTROL, FOUR-WHEEL-DRIVE and ALL-WHEEL-STEERING SYSTEM (4x4x4) - CRAB STEERING (dogway), hydraulic supports (2x / BIG SUPPORTS), SIDE - EQUALISE - SYSTEM, OVERLOAD PROTECTION SYSTEM, big driver house (colorglass), CPB, KAB - comfort seat, ROPS / FOPS, road lightnings, WORKING FLOOTLIGHT (in front/behind), WARNING LIGHT, back view mirror (2x), windshield wiper (2x), follower coupling, heating / ventilation, hold- and transport hooks. Tyres: BKT ROUGH-TERRAIN-TYRES (15.5/80 - 24) - all around approx. 98%. Transport dimensions: see above. Price is net. ∗∗∗ EQUIPMENT IS FINANCEABLE in nearly all European countries / TRANSPORTATION WORLDWIDE POSSIBLE at good conditions / EXPORT: ONLY THE NET AMOUNT NEEDED TO PAID (!) ∗∗∗∗ © pb Ksdpfx Aeuiyqdek Nodk

Condition: used, power: 74.5 kW (101.29 HP), fuel type: diesel, color: red, lifting height: 18,000 mm, tire size: 15.5 - 25, tire condition: 98 %, mast type: telescopic, Year of construction: 2011, operating hours: 2,847 h, construction height: 2,540 mm, fork length: 1,200 mm, fork carriage width: 1,200 mm, load capacity: 4,000 kg, Equipment: all wheel drive, cabin, pallet forks, Rough terrain telescopic forklift MANITOU, model: MT 1840 EP PRIVILEGE TURBO – 4x4x4. First commissioned: 2012. LIFTING CAPACITY: 4,000 kg, MAX. LIFTING HEIGHT: 18.00 m. Includes RADIO REMOTE CONTROL, EMERGENCY LOWERING, EXTRA-LONG FORKS (fork length: 1,200 mm / fork carriage width: 1,200 mm), ADDITIONAL HYDRAULICS, LOAD PROTECTION GRILL, 4-cylinder PERKINS diesel engine (101.32 HP / 74.50 kW at 2,200 rpm), CPB, FOUR-WHEEL DRIVE and FOUR-WHEEL STEERING (4x4x4) with CRAB STEERING mode, dual hydraulic stabilizers, SIDE-SHIFT ADJUSTMENT, OVERLOAD WARNING SYSTEM, PANORAMIC CABIN (large operator cab) – tinted glass, ROPS / FOPS, GRAMMER comfort seat, trailer hitch, WORK LIGHTS (front/rear), road lighting, WARNING BEACON / REVERSE ALARM, three windshield wipers, dual exterior mirrors, heater/ventilation system, OPERATOR’S MANUAL (German). Tyres: BKT OFF-ROAD TYRES (15.5 – 25) – approx. 98% tread remaining. Transport dimensions: Length: approx. 7,420 mm (approx. 6,100 mm without forks), width: approx. 2,400 mm, height: approx. 2,540 mm. Financing available / Competitive worldwide transport / For export, only net price is payable. Kjdpfxsuiwv Re Ak Nodk

Condition: used, Year of construction: 2018, operating hours: 907 h, lifting height: 18,000 mm, fuel type: diesel, mast type: telescopic, construction height: 2,540 mm, power: 55.4 kW (75.32 HP), fork carriage width: 1,100 mm, fork length: 1,200 mm, tire condition: 98 %, total length: 7,420 mm, color: red, lifting power: 4 kg/m, fuel: diesel, Equipment: all wheel drive, cabin, lighting, pallet forks, trailer coupling, Off-road - MANITOU telescopic arm forklift, type: MT 1840 ST3B TURBO - 4x4x4, first use: 2019, LIFTING FORCE: 4,000 kg, LIFTING HEIGHT: 18.00 m, LONG LOADING FORKS (Fork length: 1.200 mm / pick-up width: 1,100 mm) - ADDITIONAL HYDRAULIC, LOAD PROTECTION GRID, QUICK CHANGER, 4-cylinder DEUTZ turbo diesel engine (type: TD 3.6 L4 - 75.34 hp / 55.40 kW at 2.200 rpm), CPB, ALL-WHEEL and ALL-WHEEL STEERING (4x4x4) - DOG DRIVING, hydraulic outriggers (2x), SIDE LEVEL - REGULATION, OVERLOAD WARNING DEVICE, PANORAMIC CAB (large cab) - Colorglas, ROPS / FOPS, KAB - comfort seat, trailer coupling, traffic lights, windshield wipers (2x), exterior mirrors (2x), WARNING SOUND / WARNING LIGHT, heating / ventilation, OPERATING INSTRUCTIONS (in German). Tires: BKT OFF-ROAD TIRES (15.5/80 - 24) - approx. 98 % all-round. Transport dimensions: Length: approx. 7,420 mm (approx. 6,100 mm without fork), width: approx. 2,400 mm, height: approx. 2,540 mm. ∗∗∗ FINANCING POSSIBLE / TRANSPORTATION CHEAP (WORLDWIDE) / FOR EXPORT ONLY THE NET PRICE HAS TO BE PAID (!) ∗∗∗∗ © pb - - - - - - - - - - - - - - - - Rough terrain telescopic forklift MANITOU, type: MT 1840 ST3B TURBO - 4x4x4, first use: 2019, LIFTING FORCE: 4.000 kg, LIFTING HEIGHT: 18.00 m, LONG FORKS (fork length: 1.200 mm / width admission: 1.100 mm) - ADDITIONAL HYDRAULIC, PROTECTION LOAD GUARD, QUICK CHANGER, 4-cylinder DEUTZ turbo-diesel-engine (type: TD 3.6 L4 - 75.34 PS / 55.40 kW at 2.200 rpm), CPB, FOUR-WHEEL-DRIVE and ALL-WHEEL-STEERING SYSTEM (4x4x4) - CRAB STEERING (dogway), hydraulic supports (2x), SIDE - EQUALISE - SYSTEM, OVERLOAD PROTECTION SYSTEM, PANORAMIC-CABINE (big driverhouse) - colorglass, ROPS / FOPS, KAB - comfort seat, follower coupling, road lightnings, windshield wiper (2x), back view mirror (2x), WARNING RING / WARNING LIGHT, heating / ventilation, OPERATION MANUAL (in German). Tyres: BKT ROUGH-TERRAIN-TYRES (15.5/80 - 24) - all around approx. 98 %. Transport dimensions: see above. ∗∗∗ EQUIPMENT IS FINANCEABLE in nearly all European countries / TRANSPORTATION WORLDWIDE POSSIBLE at good conditions / EXPORT: ONLY THE NET AMOUNT NEEDED TO PAID (!) ∗∗∗∗ © pb Kdjdpfxor Nvyko Ak Nek