Low loader semitrailer

FAYMONVILLE Multimax Satteltieflader (2+2) - nachlaufgelenkt

Condition: new, maximum load weight: 36,410 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Extract from the equipment. Full equipment details available on request. GOOSENECK: * Gooseneck in SNT design for optimized loading platform length, length approx. 3,700 mm, rear with taper approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Steel front wall, removable, approx. 400 mm high * ASPÖCK-UNIBOX * 3 kW electro-hydraulic power unit for hydraulic functions, excluding hydraulic winches * Approx. 40 mm thick hardwood decking above the gooseneck * 2-inch kingpin * Gooseneck guide plate for the fifth-wheel plate, approx. 500 mm wide * Bracket at the rear of the gooseneck for ALU loading ramps * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 4 wheel chocks with holders in front of the front wall * 1 pair of stake pockets recessed on the gooseneck for plug-in stakes approx. 100 x 50 mm (located on the inside of the chassis rail) EQUIPMENT: * Loading platform length approx. 8,800 mm, extendable version approx. 4,100 mm, with rear taper approx. 500 mm x 10° * A recess in the loading platform, extending into the tapered section to accommodate the excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * Pneumatic locking with conical locking bolts and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adapt to the selected loading platform length * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steered * 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: each 12,000 kg with air suspension and raise/lower valve * 235/75 R 17.5 3PMSF twin tires. Manufacturer at our discretion * Mechanical landing legs with 2-speed gearbox and crank. JOST Module B – static test load = approx. 50,000 kg * Throughout the loading platform and between the axles, interrupted approx. 50 mm thick hardwood decking (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the telescopic tube with large cross-section. Intermediate table with offset loading platform and extendable mounting rails for aluminum bridging elements * Platform locking with conically welded locking profiles every approx. 250 mm. Includes pre-tensioning plate Hnsdpfx Aasy Auh Ijaok * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards (LC 10,000 daN) * 1 pair of fixed wheel recesses in front of the axles, open up to the gooseneck cross member, approx. 700 x 410 mm (W x D) * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom (in case vehicle is equipped with extendable widenings) * 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the platform between 1st and 2nd axle * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom * Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axle, which can also be used as widening planks (if vehicle is equipped with extendable widenings) * Lockable aluminum elements installed on the extension tubes of the widenings * 1 pair of mechanical rear supports * 1st axle with traction aid * Sandblasting painted...

Condition: new, empty load weight: 17,500 kg, maximum load weight: 43,500 kg, overall weight: 61,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,750 mm, loading space height: 400 mm, tire size: 245/70 R 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and lowered hydraulically -For tractor units: 6x4 or 8x4 Drop deck: -Low bed with external beams in extendable design, "SUPER LOW" design, length approx. 7,550 mm Hsdpfjh Hm Thsx Aaasnk -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking mechanism The supply lines are protected in the pull-out supports and automatically adjust to the respective drop-down bed length Rear chassis: -Rear chassis with closed outer frame, checker plate covering and continuous Prisma excavator trough approx. 1,450/900 x 505 mm, open at the rear -2 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame Axles and tires: -"PENDEL-AXLE", all axles with hydromechanical forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with stopcocks and locking pin for securing in raised position -Technical axle load: 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 / 3PMSF tires Accessories included: -Preparation for mounting bolt-on container positioners for 1x 20ft or 1x 40ft container on the outer beams -2" kingpin -One galvanized steel end wall approx. 400 mm high -One spare wheel with holder -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering can be operated from the front and rear by remote control cable via pushbuttons, with axle tracking control -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw coupling -Electric hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and red at the rear -2 wooden blocks 500x250x200 mm -European reflector plates (red/yellow) at the rear of the trailer -On the gooseneck and on the rear plate on the left and right, one holder each for the warning signs including socket -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 standard grease -Load manometer for determining the axle loads including load diagram -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,000 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,120 mm) -Separate air connection with air gun on the gooseneck -Duomatic air coupling from gooseneck to low bed -Gooseneck closed in the rear upper area with a removable cover -1 pair of steel ramps for bridging the mounting hooks of the low bed -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm -Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control 6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD rings VLBG-4 -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -folding extensions, approx. 230 mm on each side -A layer of sand painted onto the loading surface to prevent slipping Dipper arm recess of the rear chassis closed at the front and rear with a plug-in plate -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - aluminium 15%)

Condition: used, maximum load weight: 51,870 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, first registration: 03/2025, next inspection (TÜV): 03/2026, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Complete equipment details available upon request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, length approx. 3,700 mm, rear with chamfer approx. 1,000 mm x 10° * For tractors: 4 x 2, 6 x 2, and 6 x 4 * Plug-in steel front wall, approx. 400 mm high * At the front connection strip: yellow-red air couplings * ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for hydraulic operations * External beams of the gooseneck with mounting holes for bolted lashing rings * One mounting hole at the rear upper part of the gooseneck external beam for a bolted lashing ring * 1 pair of screw-in lashing rings included (LC 10,000 daN) * On the gooseneck, 1 pair of plug-in side aluminum drop sides, approx. 400 mm high, anodized version * On the gooseneck, 1 plug-in aluminum rear wall, approx. 400 mm high, anodized version * Approx. 40 mm thick hardwood flooring above the gooseneck * 2-inch kingpin * Gooseneck guide plate for fifth wheel, approx. 500 mm wide * Rear gooseneck mounting for aluminum ramps * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Loading platform, extendable version, length approx. 8,800 mm, rear with chamfer approx. 500 mm x 10° * Recess in the platform and chamfer for accommodating the excavator dipper stick approx. 2,490 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension * 1st and 2nd axle fixed, 3rd and 4th axles steering trailing axles * 3rd and 4th axles with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with raise and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Complete platform and interrupted between the axles with approx. 50 mm thick hardwood flooring (increasing the coefficient of friction) * Platform locking with conically welded locking profiles every approx. 250 mm * Elongated slots for insertable and repositionable bridging elements at the front of the platform * Intermediate table with set-down platform, approx. 300 mm wide, for large cross-section telescopic tube with sheet metal covering – front and rear with elongated slots for insertable and repositionable bridging elements – removable cover flush with the platform * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 6 pairs of flush-mounted lashing rings in the outside frame of the platform, foldable outward (LC 10,000 daN) * Additionally, 1 pair of lashing rings externally on the front cross member of the platform, approx. 90° turned inward towards the platform (LC 10,000 daN) * Extendable galvanized widening extensions by approx. 230 mm per side Hsdpfxoxtc Uho Aaajnk * 1 pair of permanently installed wheel recesses, open up to the extension, approx. 700 x 410 mm (W x D), sheet-covered in the platform ahead of the 1st axle, wheel recesses with square climbing strips approx. 15 x 15 mm, spaced approx. 200 mm * Between the 2nd and 3rd axles, 1 pair of permanently installed wheel recesses on the platform, approx. 1,695 x 700 x 410 mm (L x W x D), covers for wheel recesses split lengthwise, with wooden overlay, outer plug-in loc

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) Hnjdotx Nwnepfx Aaajk LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: new, empty load weight: 22,700 kg, maximum load weight: 79,300 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, loading space length: 11,000 mm, loading space width: 2,850 mm, loading space height: 920 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 22,700 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the length of the loading area, length approx. 3,750 mm, with a bevel at the rear of approx. 850 mm x 10° -Can be raised and lowered hydraulically, stroke +- 250 mm including hydraulic connection connected to the hydraulic axle compensation of the first two axles -Open in the rear third -For tractor units: 6 x 4 and 8 x 4 Loading area: -Loading area in extendable design, length approx. 11,000 mm with a bevel at the rear of approx. 500 mm x 10°. -A recess in the loading area and in the bevel to accommodate the excavator bucket handle approx. 4,240 x 900 x 440 mm -Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable supports and automatically adjust to the respective loading area length Ramps: -A pair of two-part steel ramps with a length of approx. 4,650 mm and a width of approx. 900 mm -Hydraulically foldable ramp tips. -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards -25 mm "Super Grip" rubber floor and approx. 5 mm sheet metal floor as additional reinforcement on the slope of the loading area -20x30 mm square climbing rails, approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: -PA-X axle system, all axles hydro-mechanically forced steered -The steering behavior of the first two axles can be optimally adjusted to the length of the loading area both mechanically and hydraulically. -Hose rupture valve on the axle compensation cylinder with automatic RESET function. -Hydraulic cylinder with shut-off valves and pins for securing in the raised position. -245/70 R 17.5 3PMSF Accessories included: -Steel bulkhead, pluggable, approx. 400 mm high -Connection strip for supply lines to the tractor unit, mounted at the height of the outer frame profile Hnjdjk Af Svopfx Aaajk -1 spare wheel -Outer support of the gooseneck with mounting holes for screwable lashing rings -The first hole approx. 200 mm from the front, then approx. every 400 mm -2 pairs of screwable lashing rings included -Checker plate covering above the gooseneck -On the gooseneck 1 pair of pluggable aluminum side walls on the side, approx. 400 mm high, anodized -On the gooseneck a pluggable aluminum rear wall, approx. 400 mm high, anodized -3.5" kingpin / 2" kingpin mounted -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -4 Brake shoes -4 axle load gauges -Mechanical downpipe supports at the front -1 one-piece INOX tool box, approx. 2,480 x 340 x 390 mm -Mechanical downpipe supports at the front -Continuous sheet metal covering on the loading area with a painted layer of sand to prevent slipping -1 intermediate table, approx. 500 mm wide, for the pull-out, with long holes for hanging and movable bridging elements -Painted sand coating on the support surfaces of the intermediate table -Mechanical locking for locking the intermediate table to the pull-out -8 pairs of stake pockets in the outer frame -Extensions (galvanized) extendable by approx. 230 mm per side -1 pair of hydraulic. Rear supports -Central lubrication system -1 reversing light on the left and right at the rear of the vehicle -3 kW electro-hydraulic unit -Widening planks, loose, in reinforced steel U-frame -Radio and cable remote control -4 warning signs, approx. 423 x 423 mm

Condition: used, maximum load weight: 42,500 kg, overall weight: 60,000 kg, axle configuration: 3 axles, first registration: 06/2022, with 12 axles, hydraulically suspended and divided, with hydromechanical forced steering, rear taper and drive-on ramps STZ-L Gooseneck - Robust welded steel construction - Engineered loading platform 3,950 x 2,480 mm including rear taper - Hydromechanical forced steering (dual-circuit steering system) - Turntable-mounted fifth-wheel plate with interchangeable 2-inch or 3.5-inch kingpin and adjustable steering wedge - Fifth wheel load: 24 t - Rear max. steering radius: 2,600 mm Loading platform - Lowered outer sections 4,630 mm long, 420 mm deep, resulting in a loading height of 470 mm or 830 mm with floor inserts - Extendable by 2,053 mm - Includes aluminum bridging rails for creating level surfaces - Excavator boom trough at rear running gear: 4,900 mm long, 880 mm wide, 480 mm deep - Length of rear running gear: 4,900 mm incl. 500 mm rear taper, loading height 890 mm - One pair of wheel recesses in lower deck - 3-axle hydraulically suspended running gear - Split Gigant axles with 600 mm stroke Rear of vehicle - Tapered design, 500 mm - Rear hydraulic support Drive-on ramps - Two-part drive-on ramps, 2,850 + 1,850 mm long, 800 mm wide - Rubber-coated with climbing bars Braking system - Dual-line full air braking system with diaphragm brake cylinders - Automatic load-dependent brake (ALB) - Automatic slack adjusters (AGS) - Parking brake via spring-loaded cylinders - ABS brake Special equipment Radio remote control for steering and ramp operation Central lubrication system Technical data Gooseneck Loading platform (LxW): 3,950 x 2,480 mm Loaded fifth wheel height: 1,300 mm Loading platform Platform (LxW): 10,030 x 2,850 mm, extendable by 2,053 mm Hsdpfsw Etd Tjx Aaaonk Lowered outer sections: 4,630 mm + 2,053 mm extension Center beam: 980 mm Excavator trough: 4,900 mm long, 880 mm wide, 480 mm deep Steering 1st to 3rd axle: hydromechanically forced steered (dual-circuit system)

Condition: new, empty load weight: 13,500 kg, maximum load weight: 51,500 kg, overall weight: 69,500 kg, axle configuration: > 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r17.5, color: grey, Equipment: ABS, Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm Rear gooseneck with bevel approx. 1,000 mm x 10° Cargo bed: Telescopic cargo bed, length approx. 8,800 mm, with rear chamfer approx. 500 mm x 10° Recess in the chamfer and protruding into the loading area to accommodate the excavator dipper arm Pneumatic locking with conical pin and reinforced locking positions The supply lines are protected in the extendable carrier and adapt to the respective loading area length Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps can be moved individually hydraulically outwards by approx. 235 mm and inwards by approx. 215 mm Axles and suspension: BPW axles and suspension, two axles rigid, two axles self-steering Electromagnetic reverse lock via reverse gear and can be activated manually Air suspension with lifting and lowering valve Axle tool Tires: 235/75 R17.5 3PMSF dual tires Load index: 143/141J (144/144F) Brake system: WABCO brake system, EBS-E in accordance with EU regulations Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Metallization: Standard HRM metallization of the outer frame Complete steel construction shot-peened, then the defined visible surfaces hot-finished with ZINACOR 850 (zinc 85% - aluminum 15%) metallization Steel construction: Steel grades: Hsdpfsk Ahugjx Aaajnk S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welder DIN-EN 287-1 tested MAG welding process according to EN ISO 4063 Shielding gas M21 according to EN ISO 14175 Accessories included: Steel front wall, pluggable, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets 24N connection in accordance with ISO-118524S connection in accordance with ISO-373115-pin connection in accordance with ISO-12098 Round NATO socket on the front connection strip Cable to supply the electro-hydraulic unit and/or the electric cable winch (35 mm2, 3.5 m long) between trailer and SZM with plug (NATO-NATO) 3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches 1 spare wheel with mounting adapter Outer support of the gooseneck with fastening holes for screw-in lashing ringsThe first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included One fastening hole in the rear upper area of the outer beams of the gooseneck for a screw-in lashing ring 1 pair of screw-in lashing rings Approx. 40 mm thick hardwood covering above the gooseneck On the gooseneck 1 pair of plug-in aluminium drop sides on the side, approx. 400 mm high, anodized One plug-in aluminium rear panel on the gooseneck, approx. 400 mm high, anodized 2" kingpin Guide plate from the gooseneck for the saddle plate, approx. 500 mm wide 4 wheel chocks with holder Holder for ALU docking lights Mech. Saddle supports with 2-speed gearbox and crank Continuous hardwood covering on the cargo bed, interrupted between the axles, approx. 50 mm thick Locking of the cargo bed with conically welded locking profiles every 250 mm incl. pretensioning plate Slotted holes for attachable and movable bridging elements on the front of the cargo bed 1 intermediate table with stepped loading surface, approx. 300 mm wide for the pull-out tube with large cross-section with sheet metal covering Front and rear with Langl

Condition: new, empty load weight: 11,000 kg, maximum load weight: 38,500 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Area: - Telescopic loading area with rear bevel approx. 1,000 mm x 8° - 1 pair of permanently installed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm - Wheel recesses fitted with 15 x 15 mm square anti-slip bars and widened at the lower section - Between the 1st and 2nd axle, one pair of permanently installed wheel recesses with cover, approx. 1,610 x 970 x 400 mm - Recess in the rear slope projecting into the loading area for excavator dipper arm storage, approx. 2,900 x 750 x 210/290 mm - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) Hedpjup U Hzjfx Aaaenk - 2 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - 2 pairs of lashing rings in the excavator arm recess (LC 5,000 daN) - Cut-outs in the outer frame of the loading area for securing straps (LC 2,000 daN) - Including 3-piece removable galvanized covers over the wheel recesses – max. point load 3.5 t per section Two-part Steel Ramps: - One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with 48 mm thick hardwood surfacing - Ramps with hydraulically foldable ramp sections, hydraulic lifting gear, and hydraulically transverse-adjustable Axles and Tires: - BPW axles and suspension, 2 rigid axles, 1 self-steering trailing axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear or manually - Air suspension with raise/lower valve - Axle tool kit - Tires: 235/75 R 17.5 - TPMS tire pressure monitoring system according to ECE R 141 Accessories Included: - At the gooseneck and at the rear, left and right, each with a holder for warning signs, including socket - One spare wheel - 2" king pin - One galvanized steel front wall approx. 400 mm high - Yellow-red air couplings on the galvanized front connection panel - 4 wheel chocks - Galvanized extensions, extendable by approx. 230 mm each side - Galvanized folding supports under the sloped rear of the loading area - Holder for rotating beacon at the rear of the trailer - Cover plates to bridge the gap between the ramps and loading area - White reflective tape in accordance with EU regulations on the sides and on the extension, red at the rear - Rear-mounted electro-hydraulic power unit underneath the loading area - Ramp control valves mounted on the right-hand side of the trailer - European reflective signs (red-yellow) at the rear of the trailer - Four extendable warning signs, about 423 x 423 mm, each with a position light (extendable about 400 mm) - Mounting for rotating beacon on the warning signs - On the gooseneck, plug-in aluminium side walls and rear wall ca. 2,440 x 400 mm - The rear, galvanized plug-in posts are removable (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the loading area for one 20ft or 30ft container - 3 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading area - One removable, galvanized intermediate table with 1 pair of WADER container pockets - Square anti-slip bars 20 x 20 mm every 200 mm on the outer frame of the rear slope - Painted sand grip layer as anti-slip protection on the checker plates on the gooseneck and loading area - 80 km/h speed stickers at the rear and on both sides - Ax

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle fleet, including vehicles available immediately and at short notice, on our website. Excerpt from the equipment. Full equipment details available upon request. GOOSENECK: * Gooseneck in SNT design for optimization of loading platform length, approx. 3,700 mm long, with rear chamfer approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Plug-in steel front wall, approx. 400 mm high * ASPÖCK UNIBOX at the front connection rail with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, except hydraulic winches * On the gooseneck: 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized finish * On the gooseneck: 1 plug-in aluminum rear wall, approx. 400 mm high, anodized finish * Gooseneck covered with approx. 40 mm thick hardwood, king pin area with checker plate * 2" king pin LOADING AREA: * Extendable loading platform, approx. 8,800 mm long, with rear chamfer approx. 500 mm x 10° * A depression in the platform and chamfer to take up excavator dipper sticks, approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system according to ECE R 141. Data transmission to the truck via standard EBS interface in line with ISO 11992. For correct display, the truck must be able to transmit and display this data. * TPMS tire pressure sensors mounted on all wheels * BPW axles and suspension, 1st axle steered, all other axles hydro-mechanically forced-steered * 1st axle with electromagnetic reverse lock, activated by reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve Hodpfx Asyhkrfsaajnk * Axle tools * Mechanical landing legs with 2-speed gearbox and crank, JOST Modul B, static test load = approx. 50,000 kg * 245/70 R 17.5 3PMSF twin tires. Brand at our discretion. Load index 143/141J (146/146F) * Loading area with continuous (between the axles interrupted) 50 mm thick hardwood floor (provides increased coefficient of friction) * Platform locked using welded-on conical locking profiles, every approx. 250 mm; includes pre-tensioning plate * 1 intermediate platform, approx. 300 mm wide, for large-diameter sliding tube * Intermediate platform with recessed loading area and extendable suspension bars for aluminum bridging elements * 1 pair of lashing rings on the front cross-member (LC 10,000 daN) * 8 pairs of recessed lashing rings in the outer frame of the loading area, fold-out to the outside (LC 10,000 daN) * Extendable (galvanized) platform wideners, approx. 230 mm each side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm in front of the axles, fully open to the gooseneck cross-member, approx. 700 x 410 mm (W x D) * ALU covers for the wheel recesses that can also be used as bridging elements for the extension OR as platform widening planks (if the vehicle is equipped with extendable wideners) * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * 1 pair of mechanical rear supports * Steering from front and rear via cable remote control, with single-track control of the axles HYDRAULIC LOADING RAMPS: * DR-15/60-900-4350-KG-HV-M: One pair of two-piece steel ramps, approx. 4,350 mm long and approx. 900 mm wide

Condition: used, mileage: 9,440 km, power: 382 kW (519.37 HP), first registration: 01/2024, fuel type: diesel, axle configuration: 2 axles, brakes: retarder, color: black, gearing type: automatic, emission class: euro6, Equipment: air conditioning, had accident, * ?!Engine running!? * Multifunction steering wheel * Automatic climate control * Sleeper bunk * Cruise control * Hill-start assist * Leaf/air suspension Hnsdpfx Aajvy R Iyoajk * Hydraulics * Differential lock -----Internal vehicle number: 10295----Subject to errors & prior sale. WhatsApp support available! If you have questions about the vehicle or need further information, feel free to write us conveniently via WhatsApp. Whatsapp Whatsapp