Used Fliegl Interchangeable Chassis / Swap Chassis for sale (340)

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT33901014200, empty load weight: 6,700 kg, maximum load weight: 28,300 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space height: 900 mm, total length: 13,800 mm, total width: 2,550 mm, total height: 2,500 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, color: grey-black, Chassis, Semi-trailer, Logistics Fine-grained steel welded construction, kingpin plate with replaceable 2" kingpin Outer frame slightly angled, new design with "Load-Lock profile" for securing lashing straps 24 tons, 2-speed landing gear, single-sided operation, with straight lower part, without lateral support Free support leg angle or free swivel radius to the rear, approx. 1920 mm 2 support wedges with holder Aluminum side impact protection Steel underrun protection Partial wheel covers in front of and behind each axle Splash flaps in front of the 1st axle and behind each axle with anti-splash protection, according to EC regulations 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable (lock not included) Axles + Suspension SAF drum brake axles "Axle/chassis laser-aligned" to reduce tire wear and fuel consumption Air suspension 1st axle: automatic lift axle, including forced lowering and starting assist function, activated by "3x braking" (starting assist function is operational up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Axle lift below the recommended ride height, therefore no guarantee for tire damage Braking System 2-line compressed air brake system Color-coded line routing for easy maintenance Spring brake parking brake 2 non-interchangeable coupling heads at the front, without connecting cable EBS, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With raising and lowering valve Vehicle - Driving Stability System Wheels and Tires 235/75 R17.5, brand according to the manufacturer's choice Steel rims, factory silver Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red outline lights at the rear 2 x 7-pole and 1 x 15-pole non-interchangeable sockets at the front, without connecting cable Floor Sieve-printed panels, approx. 30 mm thick, for high point load capacity for forklift axle load up to max. 5,600 kg Front wall / corner posts 25 mm aluminum hollow profile, 1,350 mm high, corner posts made of steel in a full-volume design Lhedpjza A Txefx Akksn Country of Approval / Signage Germany With DEKRA inspection and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for single-row license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paint Frame DB 7350 Novagrau Front corner posts: hot-dip galvanized Front wall: aluminum

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT33901014072, empty load weight: 7,300 kg, maximum load weight: 27,700 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 13,500 mm, loading space width: 2,530 mm, total length: 13,850 mm, total width: 2,550 mm, total height: 3,330 mm, suspension: air, tire size: 385/65 R 22,5", tire condition: 100 %, color: silver, Chassis, semi-trailer, transport company Fine-grained steel, welded lightweight construction, kingpin plate with replaceable 2" kingpin, main frame reinforcement for 25 tons, with center of gravity at 3 m loading length in the retracted state. 13 pairs of hooks for lashing straps, welded onto the cross members. 23 pairs of lashing eyes recessed in the outer frame, each rated at 3.5 tons. 24-ton, 2-speed support winch in reinforced design for loading and unloading, single-sided operation. 1 spare wheel holder for 1 spare wheel. 1 storage compartment for stowage, open, with the option of stowing items behind the front wall or in a compartment between the extended longitudinal beams! 4 pairs of stake pockets recessed in the outer frame for rectangular tubes 80x80 mm. 5 stake pockets recessed in the middle of the floor for rectangular tubes 80x80 mm, with reinforcing beam, installed between the outer stake pockets, except for one. 6 lashing/stake rails recessed across the floor over the entire width to the outer frame (max. usable internal width between the outer stake sockets approx. 2170 mm), approx. 100 mm high. With 20 mm round steel rails, top and bottom, spacing from top to bottom approx. 60 mm (of the round steel). Bottom with an angle plate as a closure, half open downwards. For lashing and inserting stakes 80 x 80 mm. Pull-out ladder at the rear on the right side. 5 x 3 pairs of stake pockets recessed on the outside of the longitudinal beams for rectangular tubes 80x80 mm, including reinforcing beams. 10 "lightweight" stake sockets, B=80/ T=80/, usable height approx. 1850 mm, hot-dip galvanized, with lashing eyes welded on at the bottom on both sides. 2 plastic toolboxes, b=600 / h=425 / t=460 mm, lockable. Telescoping extendable by a maximum of 4,000 mm and lockable approximately every 500 mm. Main frame telescoping Locking with pneumatic bolt locking + display of frame locking on both sides, operated via hand knob, operation for brake/locking and suspension on the left side in front of the axles. Storage compartment between the longitudinal beams in the extended state. Axles + Suspension SAF disc brake axles with 430 mm disc diameter. Last axle with trailing arm, with automatic reversing lock via reversing light and additional locking function on the vehicle via hand knob. Axle spacing offset 1310/1410 mm. Air suspension. 1st axle automatic lift axle, also electrically operated from the truck, with start-up assistance. Braking system 2-line compressed air braking system. Spring brake parking brake. Lsdpfx Aksza Dyyskehn 2 non-interchangeable coupling heads at the front. EBS Wabco, electronic braking system with EBS socket at the front. With raising & lowering valve + auto-reset function. Axle load recognition via EBS-CAN bus signal, for display on the display in the driver's cab, truck must be appropriately pre-equipped. Wheels and tires 385/65 R 22.5" steel rims. Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the side. 2 white position lights at the front in LED. 2 white/red side marker lights at the rear in LED. 2 x 7-pin and 1 x 15-pin non-interchangeable sockets at the front. 1 rotating beacon with bracket, switched via side light. 2 pairs of warning signs, LED illuminated and extendable to 3,500 mm. Flashing side marker lights. Side 7-pin sockets, positioning 2x front panel, 2x support legs, 2x rear end. 1 additional 7-pin socket, in the underrun protection at the rear. 2 additional LED work lights, top inside on the fron

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT33902036248, empty load weight: 7,272 kg, maximum load weight: 27,728 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 13,460 mm, loading space width: 2,470 mm, loading space height: 2,655 mm, loading space volume: 92 m³, total length: 13,800 mm, total width: 2,550 mm, total height: 4,005 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, Container color: solid color, RAL color freely selectable Chassis: semi-trailer, for forwarding companies Fine-grained steel welded construction in lightweight design, up to the support legs, trailer plate with replaceable 2" kingpin 24 tons, 2-speed support winch, single-sided operation Extension ladder at the rear Door latch on the side Folding mudguard for lighting unit Rear impact protection 1 aluminum ladder approx. 3,550 mm, with holder on the side 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Axles + suspension BPW disc brake axles with 430 mm disc diameter Air suspension, 1st axle automatic lift axle, including forced lowering and starting assist, activated by "3x braking" Braking system 2-line compressed air braking system Spring brake parking brake 2 tamper-proof coupling heads at the front 24 Volt EBS, electronic braking system with EBS socket at the front Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! with lifting and lowering valve Vehicle - driving stability system "TPMS" tire pressure monitoring system according to ECE R 141, display via display in the towing vehicle, via EBS 1 additional air connection on the left rear, with quick-release coupling Wheels and tires 385/55 R22.5", manufacturer's choice Steel rims, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the side Yellow LED lighting on the side linked to the turn signal ("flashing side marker lights") 2 white position lights at the front in LED 2 white/red side marker lights at the rear 2 x 7-pin and 1 x 15-pin tamper-proof sockets at the front, without connecting cable 2 additional LED work lights at the rear, switched via reversing light Self-tipping hydraulics Hydraulic cylinder with sliding mechanism installed in the floor. 2-circuit hydraulics. Lhedpfx Akjza S E Roksn Switching between forward/reverse operation is done electrically via remote control with cable Operation hydraulically via truck PTO Hydraulic connection with hose on the front wall and HDK screw connection NW = 48 mm Self-tipping floor Sliding floor with wear plate at the rear Floorboards made of aluminum, 8 mm floor profile, ribbed design Self-tipping container Aluminum box container made of high-quality, abrasion-resistant material. Front and side walls made of aluminum hollow profiles, welded all around at the top with a wide special reinforcing profile made of aluminum, welded to a special frame at the bottom. Sliding wall for better unloading of the load, with reinforced tarpaulin flaps at the bottom. Rear wall made of aluminum hollow profiles, as a 2-wing door, with a 1/2 to 1/2 split, framed all around with a special U-profile with stop and rubber seal, with 2 swivel latch bars on the outside, locked at the top and bottom. Rear wall with mechanical safety locking, operated at the rear on the left in the direction of travel Standing platform with ladder on both sides in the direction of travel left/right and railing, for opening and closing the roof tarpaulin 3 removable, swiveling crossbars for tarpaulin support + tarpaulin support at the front on the front wall and at the rear on the rear wall Paint finish Frame DB 7350 Novagrau "10-year warranty against rust through" Support legs Black coated Container Aluminum natural - can be painted in RAL color according to customer's request Roof tarpaulin Not yet

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT33802037879, empty load weight: 3,250 kg, maximum load weight: 34,750 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 6,790 mm, total width: 2,550 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, available in multiple units Chassis, semi-trailer, container Fine-grain steel welded construction, kingpin plate with replaceable 2" kingpin Container fittings: 1 x 20 ft, flush at the rear (Note: low drawbar load with 20 ft container) 24 tons, 2-speed landing gear, single-sided operation, with semi-circular base and straight connection plate, with stroke equalization Lhedpfx Akszbtnieken 2 support wedges with holder Rear underrun protection, steel Spray flaps at the rear, covering the entire width Half-shell fenders with anti-spray flaps according to EC Storage box for fire extinguishers up to 6 kg Fire extinguisher (ABC powder 6 kg) incl. stainless steel drip tray in the center of the rear container crossbeam, approx. 290 mm wide Axles + Suspension BPW disc brake axles, with 430 mm disc diameter "Axles/chassis laser-aligned" - reduces tire wear and fuel consumption Axle spacing offset 1410/1310 mm (combined transport), up to 44 tons total weight Air suspension 1st axle, automatic lift axle, including forced lowering and start assist, activated by "pressing the brake pedal 3 times" (start assist is functional up to an axle load exceedance of 30% and up to a speed of max. 25 km/h) Braking system 2-line pneumatic braking system Color-coded line routing for easy servicing Spring brake parking brake 2 tamper-proof coupling heads at the front, without connecting line 24-volt EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lift and lower valve Vehicle - driving stability system Axle load detection via EBS-CAN bus signal, for display on the dashboard in the cab, truck must be prepared accordingly, no truck installation (no calibrated scale) Wheels and tires 385/55 R22.5", manufacturer at the discretion of the manufacturer Steel rims, factory silver Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front in LED 2 white/red marker lights at the rear 1 x 15-pin socket at the front, without connecting cable Operating instructions The specified total weight is technically possible; depending on the cargo, the total weight may not be reached while complying with the permissible axle/support and drawbar loads. (Poor driving and handling characteristics possible due to incorrect load distribution) Country of registration/plates Germany with Dekra inspection and certificate (according to §13 EG - FGV) 24/7 service hotline prepared for single-row license plate holder Warning sign "A" for waste transport, foldable ADR approval according to FL/AT with ADR warning sign at the rear Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paintwork Frame RAL 2011 traffic orange "10-year warranty against rust-through" Support feet black coated available in multiple units

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 2,520 kg, maximum load weight: 8,000 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,050 mm, loading space height: 400 mm, total length: 7,280 mm, total width: 2,550 mm, total height: 2,900 mm, suspension: steel, tire size: 235/75 R17,5", tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Chassis: Central axle trailer, low loader Fine-grained steel welded construction Gear-supported front support Telescopic rear support 2 chock blocks with holder Fenders made of sheet steel over both wheels with anti-splash flaps only on the last axle Aluminum side impact protection Front crossbar that can be inserted into the floor holes Coupling device for central axle trailer Drawbar with tested 40 mm towing eye Drawbar height-adjustable via spindle, max. adjustment range 250 mm Axles + Suspension Lsdpfezcnugsx Akkohn BPW drum brake axles "Axle/chassis laser-aligned" – reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (linkage compensation) Wheels and tires 235 / 75 R 17.5" as per manufacturer's choice Steel rims, factory silver Braking system 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle Parking sockets for electrical wiring, ABS/EBS and air connection to the drawbar 24 Volt EBS, Electronic Braking System with EBS plug at the front, with connecting cable Caution: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! "TPMS" tire pressure monitoring system according to ECE R 141, display via display in the towing vehicle, via EBS Electrical system 24 Volt, multi-chamber lights in LED, yellow LED lighting on the side, license plate lighting in LED Yellow LED lighting on the side coupled with the turn signal "flashing side lights" 2 white position lights at the front in LED 2 white/red outline lights at the rear in LED Premium LED side marker lights, with "20 LED diodes per light" 2 x 7-pole fail-safe plugs at the front, with connecting cable Platform TTS low-lying steel tub, platform floor made of steel/non-slip metal plate, steel walls firmly welded to the floor Platform length 5500 mm Tub with "Load-Lock profile" at the front and on the side for attaching lashing straps (8 pieces at the front, 16 pieces on each side) 2 pairs of lashing rings, 1 x at the front in the corners of the steel tub and 1 x at the rear in the floor, each 5 tons 3 pairs of additional lashing rings in the floor, each 5 tons 4 pairs of lashing rings screwed onto the side walls Ramps Steel ramps, 2,300 mm long, 510 mm wide, can be shifted sideways with handrail on the ramps covered with wood (tip area with steel/non-slip metal plate) with gas spring for single-person operation Rear wall / rear corner posts Screen-printed panel, 400 mm high, pluggable, between ramps Operating instructions The specified total weight is technically possible, depending on the load, the total weight may not be reached while complying with the permissible axle/support and saddle loads. Country of registration / signs Country of registration: Germany Type approval according to EG 2007/46 prepared for license plate holder, single-line Contour marking with reflective strips according to ECE R 048, white on the side and red at the rear Warning sign according to ECE - 70 Custom-made transport solution

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 2,900 kg, maximum load weight: 8,900 kg, overall weight: 11,800 kg, axle configuration: 2 axles, loading space length: 6,200 mm, loading space width: 2,480 mm, total length: 8,000 mm, total width: 2,550 mm, total height: 3,000 mm, suspension: steel, tire size: 235/75 R17,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Chassis: Center-axle trailer Fine-grained steel welded construction Outer frame slightly angled, new design with "Load-Lock profile" for tie-down straps 3 pairs of lashing eyes outside in the floor, each 5 tons 1 at the front in the corners, 1 in front of and 1 in the rear incline at the back 6 pairs of lashing eyes outside in the floor/outer frame, each 5 tons Gearbox support leg at the front Rear support, foldable 2 wheel chocks with holder Aluminum side impact protection Steel underrun protection, galvanized Splash guards at the rear covering the entire width (not in combination with forklift mount) Quarter panel fenders 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Coupling device: Center-axle trailer Lhodpfxjzcqpao Akken Drawbar with tested 40 mm drawbar eye Drawbar height-adjustable via spindle, max. adjustment range 300 mm Axles + Suspension GFA or BPW axles, at the manufacturer's choice, with tapered roller bearing and S-cam brake "Axle/chassis laser-aligned" - reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (lever compensation) Braking System 2-line compressed air brake system Color-coded line routing for easy servicing Hand-spindle parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle 24 volt ABS and ALB, with ABS connector at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and Tires 235/75 R17.5, manufacturer's choice Steel rims, factory silver Electrical System 24 volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front, in LED 2 white/red marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connecting cable Floor Steel/diamond plate floor for high point load capacity Note: Slight floor waviness due to welding distortion is possible! Platform length approx. 6,200 mm Rear incline to approx. 900 mm Front wall / corner posts at the front 25 mm aluminum hollow profile, 400 mm high Side walls 25 mm aluminum hollow profile, 400 mm high, foldable and removable Rear wall / corner posts at the rear 1 pair of steel uprights attached to the frame, with brackets for locking the access ramps, access width approx. 2,430 mm Access Ramps Steel ramps 2,300 mm long, 510 mm wide, laterally movable With handrail on the ramps Covered with wood (tip area with steel/diamond plate) With gas spring for one-person operation Operating Instructions The stated total weight is technically possible; depending on the cargo, the total weight may not be reached while complying with the permissible axle/support and saddle loads. (Poor driving and following behavior possible due to incorrect load distribution) Country of Registration / Signs Germany With DEKRA inspection and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-row license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paintwork Frame DB 7350 Novagrau "10-year warranty against rusting" Front wall Aluminum Side wall Aluminum, anodized Access ramps Hot-dip galvanized Customized Transport Solution

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,220 kg, maximum load weight: 8,580 kg, overall weight: 11,800 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 450 mm, total length: 6,900 mm, total width: 2,550 mm, total height: 1,550 mm, suspension: steel, tire size: 235/75 R17,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized to meet individual customer needs. Chassis: Central axle tilting trailer Steel welded construction, continuous tilting shaft at the rear with 80 mm ball bearing Gear-supported front support leg Foldable rear support Wheel chocks with holder Underrun protection, steel Splash guards at the rear, covering the entire width (not in conjunction with forklift mount) Quarter panel fenders 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable (lock not included) Note! The side panel touches the storage box when folded down. Lockable storage space for loading ramps below the loading area Coupling device for central axle trailer Drawbar with tested 40 mm tow hitch Drawbar height adjustable via spindle, max. adjustment range 300 mm Axles + Suspension GFA or BPW axles, at the manufacturer's choice, with tapered roller bearing and S-cam brake "Axle/chassis laser-aligned" - reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load equalization (linkage equalization) Wheels and Tires 235 / 75 R 17.5", manufacturer's choice Steel rims, factory silver Braking System 2-line compressed air braking system Color-coded line routing for easy servicing Handwheel-operated parking brake 24 Volt ABS and ALB, with ABS connector at the front, with connection cable Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 fail-safe coupling heads at the front, with connection lines to the towing vehicle Electrical System 12 to 24 Volts, multi-chamber lights in LED, yellow LED side lighting, license plate lighting in LED 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pole fail-safe connectors at the front, with connection cable Additional LED work lights at the rear, switched via reversing light Hydraulics Three-way tipper, hydraulic multi-piston cylinder with stroke limitation and safety cable Low-pressure cylinder up to max. 170 bar, without throttle. If required, this must be retrofitted on the truck (truck with max. hydraulic flow rate of 55 l/min) Hydraulic connection with SVK connector NW 10/3, including connection hose Operation hydraulically via truck auxiliary drive Tipping Platforms Lsdpfozcv Stjx Akkshn Stable tipping platform with 4 mm steel sheet base, side panel construction in steel, side walls continuous, foldable and pivotally mounted with central locking at the bottom. Rear corner posts pluggable. Rear wall foldable and pivotally mounted, with central locking at the bottom. Platform length approx. 5,000 mm, side walls with 6 hinges at the bottom. Side panel retraction springs Platform width 2420 mm 3 pairs of lashing eyes in the floor, each 5 tons Paint Finish Frame: Hot-dip galvanized including passivation "15-year guarantee against rust through" Side panels/platform: galvanized or painted according to customer requirements Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized to meet individual customer needs.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,600 kg, maximum load weight: 13,400 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,370 mm, loading space height: 900 mm, total length: 7,200 mm, total width: 2,550 mm, total height: 2,350 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your individual requirements. The vehicle shown is an example configuration. Production and equipment are tailored to customer specifications. Lhedpozcyl Refx Akken *Chassis – Tandem Three-Way Tipping Trailer Welded steel chassis construction Continuous rear tipping shaft with 100 mm spherical tipping bearing Two-speed landing gear at the front Foldable rear support legs Wheel chocks with holder Steel underrun protection Quarter mudguards in front of and behind each axle Anti-spray mud flaps behind each axle Lockable storage compartment for aluminium loading ramps beneath the platform 1 pair of aluminium loading ramps, approx. 3,600 mm long and 400 mm wide, load capacity 8,000 kg per pair Plastic toolbox with shelf insert, dimensions: 620 x 360 x 440 mm (W x H x D), lockable with padlock *Drawbar Drawbar with certified towing eye *Axles & Suspension BPW drum brake axles Air suspension with raise-and-lower valve *Wheels & Tyres 385/55 R 22.5 tyres, manufacturer's choice Steel rims, factory silver finish *Braking System Dual-line compressed air braking system Spring-loaded parking brake Two non-interchangeable coupling heads at the front with connecting lines to the towing vehicle EBS (Electronic Braking System) with front EBS connector and connecting cable *Electrical System 24 V electrical system Multi-chamber rear lights Yellow LED side marker lights 2 white front position lights 2 white/red rear outline marker lights 2 x 7-pin non-interchangeable front plugs with connecting cable *Hydraulic System Three-way tipping mechanism Hydraulic multi-stage tipping cylinder with stroke limiter and safety cable Hydraulic connection with SVK coupling NW 10/3, including connecting hose Hydraulic operation via truck PTO (power take-off) *Tipping Body 4 mm HB 400 steel floor Rear spherical tipping bearing, 100 mm diameter Steel side walls, drop-down and pendulum-mounted, with central locking at the bottom Front wall and side walls approx. 800 mm high Steel rear wall approx. 600 mm high, designed as a combination pendulum tailgate Side wall return springs 4 pairs of external lashing rings in the floor, each rated at 3 t 2 pairs of recessed floor lashing rings, each rated at 5 t *Registration & Compliance Registration country: Germany DEKRA inspection and certification included 24/7 service hotline Prepared for single-line licence plate holder Reflective contour markings according to ECE R048 (white on the sides, red at the rear) Rear warning plate according to ECE 70 *Paint Finish Chassis: galvanised or painted according to customer requirements Body and side walls: painted according to customer requirements Customized Transport Solution Configure your Fliegl vehicle according to your individual requirements. The vehicle shown is an example configuration. Production and equipment are tailored to customer specifications.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 11,000 kg, maximum load weight: 27,000 kg, overall weight: 38,000 kg, axle configuration: 3 axles, loading space length: 9,500 mm, loading space width: 2,480 mm, loading space height: 3,040 mm, total length: 13,800 mm, total width: 2,550 mm, total height: 4,020 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Chassis Steel welded construction with narrow crossmember spacing and reinforced design, low-loader outer frame profile, for transporting construction machinery up to 32,000 kg and with a maximum outer width of the construction machinery of 2550 mm, kingpin plate with replaceable 2 kingpins. Rear slope of approx. 1200 mm and 7°. Ramp shaft closed at the top with steel/diamond plate, in the low-bed, omega rail laterally at the bottom on the outer frame as a mounting rail for tarpaulin and spacers for lashing points, not in the wheel area. If a lift table is used, there is an additional, lightweight outer frame with an omega profile. 24-ton, 2-speed landing gear, single-sided operation, with a semi-circular lower part and a straight connection plate, with stroke compensation, free swivel radius to the rear approx.: 1950 mm, rear support, foldable 2 wheel chocks + holder Side underrun protection, aluminum Quarter panel fenders in front of and behind each axle with anti-splash flaps behind each axle Underrun protection, steel Splash flap at the rear over the entire width 4 storage boxes, stainless steel, w=800/h=350/d=350 mm, with a polished, lockable door, 2 x on the left front and 2 x on the right front in front of the 1st axle Lift table behind the gooseneck, approx. 3000 mm long, hydraulically liftable for crossing over the gooseneck, with mechanical locking in the raised position. (Cylinder angled for good ground clearance, Fliegl standard). Operation on the right front + additional activation with a wireless remote control, lift table can be raised with the tarpaulin closed! Tarpaulin attachment in the lift table area to an additional, lightweight outer frame with omega profile, lift table can be raised with the tarpaulin closed! Lashing points can also be used in the lowered position! Lashing points Gooseneck: 4 pairs of 5-ton lashing points embedded in the outer frame 2 pairs of lashing points at the top and on the side embedded in the outer frame 8 pairs of lashing points at the top and on the side embedded in the outer frame, each 10 tons 9 pairs of 5-ton lashing points embedded in the outer frame Axles + Suspension SAF drum brake axles last axle with trailing steering knuckle, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lifting and lowering valve + auto-reset function H&S function with quick vent 1st axle, automatic lift axle, incl. forced lowering and starting assist, activated by pressing the brake pedal 3 times (starting assist is functional up to an axle load exceedance of 30% and a speed of max. 25 km/h) Axle lift below the recommended ride height, no guarantee for tire damage Wheels and tires 235/75R17.5 from leading manufacturers Steel rims in twin arrangement, factory silver Braking system 2-line pneumatic braking system Lhjdpoi Riw Ajfx Akkon Spring brake parking brake 2 foolproof coupling heads at the front EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Axle load recognition in the truck via EBS, without installation in the truck. Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white

Condition: used, machine/vehicle number: WFDFLT21601003376, empty load weight: 2,600 kg, maximum load weight: 10,800 kg, overall weight: 13,400 kg, axle configuration: 2 axles, first registration: 01/2014, tire size: 285/70 r19,5, Further information: Fine-grained steel welded construction, fifth wheel coupling, manufacturer at our discretion for 2 kingpins, telescopic support leg, chock blocks with holder, steel underride guard, half-shell fenders. Drawbar with tested 50 mm drawbar eye, lower coupling drawbar mechanically adjustable in length. BPW disc brake axles, air suspension with raise and lower valve, electronic dolly steering system, sensor via contact in the drawbar eye (required in Germany to comply with the BO-Kreis regulation, or the semi-trailer must be steerable). 2-line pneumatic brake system, spring-loaded parking brake, 2 non-interchangeable coupling heads at the front, with connecting lines to the tractor unit, 2 non-interchangeable coupling heads to the semi-trailer. Lodpsi Riydofx Akkshn EBS, electronic braking system with EBS plug at the front, with connecting cable, EBS connecting cable to the semi-trailer, axle load recognition for the truck via EBS, without truck installation. 24 Volt, multi-chamber lights, yellow LED lighting on the sides, 2 white position lights at the front, 2 white/red marker lights at the rear, 1 x 15-pole plug at the front. Registration country: Germany, with Dekra approval, prepared for single-row license plate holder, contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear, warning sign according to ECE - 70. Fifth wheel height approx.: 960 mm.

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 6,750 kg, maximum load weight: 32,250 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 9,950 mm, loading space width: 2,480 mm, loading space height: 2,150 mm, loading space volume: 50 m³, total length: 10,300 mm, total width: 2,550 mm, total height: 3,670 mm, suspension: air, tire size: 385/65 R 22,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. More information Chassis, Saddle, Tipper Fine-grained steel welded construction, in basic lightweight design, saddle plate with interchangeable 2 kingpin Curved front end, patented 24 ton, 2-speed support winch, single-sided operation, with straight lower part, without thrust compensation Wheel chocks with holder Underrun protection, foldable Half-shell fenders Integrated fender holder, surface designed to repel stones Tarp rod with holder Towing hook at the rear Axles + Suspension BPW disc brake axles with 430 mm disc diameter Axle/suspension laser-aligned to reduce tire wear and fuel consumption Air suspension 1st axle, automatic lift axle, including forced lowering and start-up assistance Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking system 2-line compressed air braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With raising and lowering valve Vehicle - driving stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver "TPMS" tire pressure monitoring system according to ECE R 141, display via display in the towing vehicle, via EBS, without truck installation (this must be available in the truck. Only on standard tires). Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides Yellow LED lighting on the sides, linked to the turn signal ("flashing side lights") 2 x 7-pole fail-safe sockets at the front, without connecting cable Hydraulics Low-pressure cylinder, max. 170 bar, smallest stage hard-chromed, with HDK screw-on fitting, fixed part, NW 48 mm (without hose connection) Operation via truck auxiliary drive Body Steel side body made of highly wear-resistant HB 400 steel, sloping front wall with externally mounted hydraulic cylinder mount. Shovel and broom holder on the outside of the front wall. Internal access ladder on the front wall. Side walls continuously 3 mm thick, floor continuously 3 mm thick Membrane - rear wall Internal width at the bottom approx. 1440 mm Lhodoi Rizfspfx Akksn Aluminum rear wall, pendulum-mounted with "double-hinge hinge" and with 2-wing door, split 1/2 to 1/2, at the top with pivoting boom, each with a grain slide per door. Standing platform with access ladder, connection plate for air/electricity and brake with large space for optimal operation. Roller cover on one side for placement on the right side, with central locking on the left side Country of approval/signs Germany Type approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for license plate holder, single-line Warning sign according to ECE - 70 Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paint Frame: DB 7350 Novagrau "10-year warranty against rust-through" Body: RAL, single color, according to customer's choice Roller cover: RAL 7035 light gray

Condition: new, functionality: fully functional, empty load weight: 4,780 kg, maximum load weight: 33,220 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 11,250 mm, total width: 2,550 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Chassis, Saddle, and Container Fine-grain steel welded construction, saddle plate with 2 replaceable kingpins and 2 kingpin positions Container mounts: Rear extension retracted: 1 x 20 ft, flush at the rear, low saddle load Rear extension extended, 1st stage: 1 x 30 ft, 2 x 20 ft, 1 x 40 ft with gooseneck tunnel Rear extension extended, 2nd stage: 1 x 45 ft with short gooseneck tunnel and overload to the rear Rear extension extended, 2nd stage + front extension, 1st stage: 1 x 45 ft with long gooseneck tunnel and angled corners with height adjustment at the rear and folding center supports for containers without a tunnel Container guide at the front, pluggable and removable Plug adapter for front locking, to lock containers without a tunnel from below, with holder when not in use Front extension on rollers, manually extendable (for 45 ft containers with long tunnels) Rear extension on rollers, with hand crank 24 ton, 2-speed support winch, single-sided operation 2 chock blocks with holder Aluminum side impact protection Galvanized steel underrun protection Extendable underrun protection for 45 ft containers Half-shell fenders with anti-spray flaps according to EG Rear impact protection Axles and Suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-aligned, reducing tire wear and fuel consumption Offset axle spacing mm (combined transport), up to 44 tons gross vehicle weight Air suspension 1st axle: automatic lift axle, including forced lowering and start-up assistance, activated by 3x braking (start-up assistance is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Braking System 2-line pneumatic braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connecting cable Note: The trailer may only be towed by tractor units that guarantee the effectiveness of the ABS! with lift and lower valve + auto-reset function Vehicle - Driving Stability System Axle load detection via EBS-Canbus signal, for display on the display in the driver's cab, the truck must be appropriately prepared Wheels and Tires 385/55 R22.5, manufacturer's choice Steel rims, factory silver Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe sockets at the front Operating Instructions Special permit required if the overall train length exceeds 16,500 mm. When transporting 45 ft containers with a short tunnel, with or without a front extension, the permissible system length from kingpin to the rear edge of the vehicle and the overall train length of 16,500 mm will be exceeded! The underrun protection must be manually extended! An exemption permit according to § 70 StVZo is required! Approval / Signage Germany Type approval according to EG 2007/46 24/7 service hotline prepared for single-row license plate holder Warning sign according to ECE - 70 Lodpfsi Rizusx Akkohn Contour marking with reflective tape

Condition: new, functionality: fully functional, overall weight: 16,000 kg, maximum load weight: 13,700 kg, empty load weight: 2,300 kg, loading space width: 2,480 mm, loading space length: 7,750 mm, loading space height: 3,000 mm, machine/vehicle number: Produktpalette, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Tandem Trailer Chassis Welded steel construction with a floor assembly approximately 152 mm high; load-bearing and torsionally rigid steel frame construction. Longitudinal beam floor construction with a load-resistant outer frame and guide tunnels spaced 600 mm apart; tunnels feature guides on top and sides, tunnel height approx. 45 mm; 4 x swap body corner fittings based on a 20-foot standard. 4 side-extending/folding parking feet with dual locking mechanism for a parking height of 970 mm, with support leg rest Side door stops Rear impact protection made of flat bar Pallet stops on both sides, approx. 20 mm high with perforated profile for securing straps; loading height is reduced by approx. 20 mm Floor Screen-printed panels approx. 27 mm thick, for high point load capacity, for forklift axle load up to max. 4,400 kg Front wall/corner stanchions Approx. 2,580 mm high, remainder covered with tarp; steel corner stanchions in full-size design; release mechanism for side tarp on front wall Inner front wall additionally lined with a 1,250 mm high screen-printed panel Center stanchions 1 pair of sliding stanchions adjustable along the entire length, with 4-compartment pockets and a long pocket at the bottom. 1 pair of stanchion positions Slotting Slats 5 rows of wooden V-shaped slotting slats Rear wall/rear corner stanchions Rear steel corner stanchions extending to the bottom edge of the roof, tarpaulin attachment with round tube and tarpaulin tensioning ratchet Rear portal doors, double-leaf, each with 2 internal twist-lock latches Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps, reinforcements for stanchions Stainless steel tensioning fasteners Roof Sliding roof, rear end lift folds up, roof can be slid from rear to front, L-shaped roof rail for the automotive industry, interior width between roof rails approx. 2,490 mm, tarpaulin color: white EcoLift – lifting roof by approx. 380 mm, liftable on both sides, with gas spring assistance, Registration / Plates Country of registration: Germany Lhodpfx Akekt Ni Uoksn Fliegl manufacturer’s certificate for body strength in accordance with EN 12642 XL, Fliegl manufacturer’s certificate for body strength in accordance with DL 9.5, pallet stops on both sides, approx. 20 mm high, loading height reduced by approx. 20 mm Fliegl manufacturer’s certificate for load securing in accordance with VDI 2700, Sheet 12 ff. Pallet stops on both sides, approx. 20 mm high; loading height is reduced by approx. 20 mm Paint Finish Frame Hot-dip galvanized, including passivation Front corner posts Hot-dip galvanized Front wall Aluminum Rear corner posts Hot-dip galvanized Rear wall White

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 2,800 kg, maximum load weight: 15,200 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,300 mm, total width: 2,550 mm, total height: 1,300 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your individual requirements. The vehicle shown is an example configuration. Production and equipment are tailored to customer specifications. ### Chassis – Turntable Drawbar Trailer for Roll-Off Containers * High-tensile steel welded chassis construction * Sliding frame system: * The container is loaded from the rear onto the sliding frame and pushed forward * Front container stop adjustable for 6.0 m, 6.5 m and 7.0 m roll-off containers with external rollers * Container locking system: * 2 pairs of recessed locking hooks integrated into the floor * Pneumatic operation * Internal 2-point locking system * Not suitable for roll-off containers with internal centre beam * Designed for the transport of roll-off containers with subframe according to DIN 30722 * Heavy-duty turntable with ball-bearing slewing ring * 2 wheel chocks with holders * Aluminium side underrun protection * Steel rear underrun protection * Semi-circular mudguards * Rear impact protection, mounted vertically on left and right side, with delta rubber buffers on underrun protection brackets * Spare wheel carrier for 1 spare wheel, including wheel mounting kit * Plastic toolbox with drawer and shelf insert, dimensions: 650 x 520 x 670 mm (W x H x D), lockable with padlock ### Drawbar * Drawbar with certified 40 mm towing eye ### Axles & Suspension * SAF disc brake axles Lhedpfx Akjzggghokjn * Laser wheel alignment of axles and suspension for reduced tyre wear and lower fuel consumption * Air suspension with raise-and-lower valve ### Wheels & Tyres * 385/55 R 22.5 tyres * Manufacturer's choice * Steel rims, factory silver finish ### Braking System * Dual-line compressed air braking system * Spring-loaded parking brake * Drive-away protection: opening the container locking system automatically activates the spring-loaded parking brake * Vehicle Stability Control System * Two non-interchangeable coupling heads at the front with connecting lines to the towing vehicle * EBS (Electronic Braking System) with front EBS connector and connecting cable Note: The trailer may only be operated with towing vehicles that ensure proper ABS functionality. ### Electrical System * 24 V electrical system * Multi-chamber rear lights * Yellow LED side marker lights * 2 white front position lights * 2 white/red rear outline marker lights * 2 additional LED work lights at the rear, activated via reverse gear * 2 x 7-pin non-interchangeable front plugs with connecting cable ### Registration & Compliance * Registration country: Germany * DEKRA inspection and certification included (according to §13 EC-FGV) * 24/7 service hotline * Prepared for single-line licence plate holder * Reflective contour markings according to ECE R048 (white on the sides, red at the rear) ### Paint Finish * Chassis: hot-dip galvanised or painted according to customer requirements * Drawbar: black KTL coating (cathodic dip coating) Customized Transport Solution Configure your Fliegl vehicle according to your individual requirements. The vehicle shown is an example configuration. Production and equipment are tailored to customer specifications.

Condition: used, empty load weight: 5,933 kg, maximum load weight: 29,067 kg, overall weight: 35,000 kg, axle configuration: 3 axles, Condition - Very well-maintained vehicle from first owner Category - Semi-trailer Model - FLIEGL DHKA 350 - 35,000 kg Registration Month - 02 Registration Year - 2013 Gross weight (kg) – 35,000 Unladen weight (kg) – 5,933 Lhjdpswk Ux Nsfx Akkon Payload (kg) – 29,067 Colour - Silver Number of axles - 3 Maintenance - Inspection record Commercial/Export - Net price in € - 19,990 Subject to prior sale, changes, and errors Phone +49 551 50 84 912 According to manufacturer: Axles and Suspension SAF disc brake axles with 370 mm disc diameter; air suspension with raise/lower function; 1st axle is an automatic lift axle, includes forced lowering and starting aid, actuation by 'brake 3x' (starting aid is operational up to axle load exceedance of 30% and up to a maximum speed of 25 km/h) Chassis Special lightweight steel welded construction; fifth wheel plate with replaceable 2” kingpin Support legs Not equipped Tyres/Wheels 385 / 65 R 22.5”, manufacturer’s choice; polished aluminium rims, manufacturer’s choice Braking system 2-line brake system per EC regulation; EBS; 2 non-interchangeable coupling heads; spring-actuated parking brake; without connecting cable Electrics 24 Volt, multi-chamber rear lights; 2 x 7-pin non-interchangeable sockets; lighting per EC regulation; without connecting cable Hydraulics Low-pressure cylinder max. 170 bar with HDK threaded coupling; fixed section, NW 48 mm (without hose connection) Body Aluminium floor made of high-quality, abrasion-resistant material, 5 mm thick, Brinell 110, reinforced with U-profiles; side walls in hollow chamber profiles, precisely welded, with upper rail profile for bulk material shedding; front wall slanted, rear wall as pendulum tailgate with double-joint hinge, exterior mounting with double hook lock. Note! Suitable only for the transport of sand, gravel, and rolled chippings with a maximum grain size of up to 20 mm! All other transported goods are excluded from warranty! Paintwork Chassis shot-blasted, primed, and final coat single colour 2K/HS acrylic paint in DB Novagrau; body RAL 9010 pure white with 'Revolution' lettering Miscellaneous Foldable underrun bar; wheel chocks with holder; 1/2 shell plastic mudguards; with Dekra inspection and certificate (per §13 EC FGV); contour marking with reflective tape per ECE R 048, side in white, rear in red; shovel and broom holder mounted on front wall

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,660 kg, maximum load weight: 33,340 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 10,450 mm, total width: 2,550 mm, total height: 1,325 mm, suspension: air, tire size: 385/55 R22.5", tire condition: 100 %, Year of construction: 2026, Tailor-made transport solution Configure your Fliegl vehicle to your requirements. The vehicle shown is an example. Production and specification are carried out individually to customer requirements. #Chassis, semi-trailer container - Fine-grain steel welded construction, fifth wheel plate with replaceable 2" kingpin and 2 kingpin positions - Front locking on tipping ram mounting bracket with guide wedges on both sides, rear locking on continuous twist-lock shaft with return spring - Without subframe, for self-supporting containers - Container mounts: locking crossmember, twin-point for locking 1 x 30 ft container - 24 t 2-speed landing legs, single-side operation, with straight foot, without slide compensation - Clear landing leg corner dimension / rear swivel clearance approx. 1850 mm - 2 wheel chocks with holder - Aluminium side underrun protection - without rear underrun protection - Half-shell mudguards - with anti-spray mudflaps to EC standard #Hydraulics - Low-pressure cylinder max. 170 bar, smallest stage hard chrome-plated, with HDK screw coupling, fixed part, NW 48 mm (without hose connection). Caution! Tipping angle limited! - Hydraulic actuation via truck PTO - Hydraulic connection with hose and HDK screw connector NW = 48 mm with knurled nut #Axles + Suspension - BPW disc brake axles with 430 mm disc diameter - "Laser-aligned axles/chassis", reducing tyre wear and fuel consumption - Staggered axle spacing 1410/1310 mm (combined transport) up to 44 t gross train weight - Air suspension - 1st axle automatic lift axle, including forced lowering and traction assist, activated by "3x braking" (traction assist functions up to an axle load excess of 30% and up to a speed of max. 25 km/h) #Braking system - Two-line compressed-air braking system - Colour-coded line routing for easy servicing. - Spring-loaded parking brake - 2 mismatch-proof coupling heads at the front, without connecting line - 24 V EBS electronic braking system with EBS socket at the front, without connecting cable - Caution: the trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! - with raise & lower valve - Vehicle driving stability system - Axle load detection via EBS CAN bus signal, for display on the cab monitor; the truck must be pre-fitted accordingly, no installation on the truck included (not a calibrated weighing system) #Wheels and tyres - 385/55 R22.5" make at the manufacturer's discretion - Steel rims, factory silver #Electrics - 24 V multi-chamber lights, yellow LED side lighting - 2 white LED position lights at the front - 2 white/red outline marker lights at the rear - 2 x 7-pin mismatch-proof sockets at the front, without connecting cable #Country of registration / Plates - Type approval to EC 2007/46 - 24/7 service hotline - prepared for single-line number plate holder Ledjzy N Hkjpfx Akkjhn - Contour marking with reflective strips to ECE R048, white on the sides and red at the rear #Paintwork - Frame: RAL colour of choice - "10-year warranty against corrosion perforation" - Landing legs: black coated

Condition: used, empty load weight: 6,075 kg, maximum load weight: 28,925 kg, overall weight: 35,000 kg, axle configuration: 3 axles, next inspection (TÜV): 03/2027, total length: 13,850 mm, total width: 2,550 mm, total height: 4,000 mm, suspension: air, tire size: 435/50 R19,5, color: red, Year of construction: 2023, Equipment: ABS, Color: RAL 3002 Carmine Red Front/rear panel: Purple / white Extension ladder at the rear, door latch on the side Support wedges with holder, aluminum side impact protection, galvanized steel underride protection, quarter panel fenders in front of the 1st axle and behind each axle, with anti-spray flaps behind each axle, rear impact protection, Pallet stop on both sides, approximately 15-20 mm high, in a bolted design, loading height is reduced by approximately 15-20 mm, plastic toolbox Axles + Suspension SAF disc brake axles, "axle/chassis laser measured" to reduce tire wear and fuel consumption, air suspension, 1st axle automatic lift axle, including forced lowering and starting assistance, Lhjdpjzun I Asfx Akkon Activation via "3x braking" (starting assistance is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Axle lift below the recommended ride height, therefore no warranty for tire damage Braking system 2-line compressed air braking system, color-coded lines for easy servicing, spring brake parking brake, 2 fail-safe coupling heads in front, without connecting line, EBS, electronic braking system with EBS socket in front, without connecting cable. Note: The trailer may only be pulled by towing vehicles that ensure the effectiveness of the ABS! with lifting and lowering valve Ride height in conjunction with lift axle, when the lift axle is raised, the loading or overall height increases by 50 mm (in Mega Flex only at low ride height or saddle height), vehicle - driving stability system Wheels and tires 435/50 R19.5", manufacturer's choice, steel rims, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the side, 2 white position lights in front 2 white/red marker lights at the rear, 2 x 7-pole and 1 x 15-pole fail-safe sockets in front Floor Sieve-printed panels approximately 30 mm thick, on longitudinal supports for high point load capacity for forklift axle load up to max. 7100 kg Front wall / corner posts 2,580 mm high, corner posts steel in volume design, release device for side tarpaulin on front wall, "Crash-Blocker," bottom inside at approximately 140 mm height with steel impact protection Intermediate supports 3 pairs of sliding supports, fully adjustable in length, with 4-fold insertion pockets and a long pocket at the bottom, 3 pairs of support positions Insertion slats 5 rows of wooden insertion slats Rear wall / corner posts Corner posts at the rear, steel up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet Rear portal doors, 2-wing with 2 internal rotary rod locks each Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps Tensioning closures made of stainless steel Roof Fliegl sliding roof, sliding cover, end lift at the rear that can be folded up, with a cover that can be slid from back to front, L-shaped roof beam for the automotive industry, inner width between the roof beams approximately 2,490 mm, tarpaulin color: white, roof non-elastic, little deflection of the roof beam during loading and unloading, EcoLift - lifting roof can be raised by approximately 380 mm, on both sides, with gas spring support, 3 driving positions in the front: interior height in the front approximately 2900mm/ 2950 mm / 3000 mm Optimal rain strip at the rear, on top of the end rail, above the doors Fliegl manufacturer certificate for body strength according to EN 12642 XL, Fliegl manufacturer certificate for body strength accor

Condition: used, axle configuration: 3 axles, first registration: 07/2013, suspension: air, tire size: 385/65, tire condition: 30 %, color: other, Equipment: ABS, = Additional options and accessories = Ledpfx Akszvdp Sskohn - ADR - Air Suspension - BPW Axles - Disc brakes = More information = Year of construction: 2013 Tyre size: 385/65 Make axles: BPW Tyre profile: 30% Brakes: disc brakes Suspension: air suspension

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 6,200 kg, maximum load weight: 32,800 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 13,650 mm, loading space width: 2,480 mm, loading space height: 3,000 mm, total length: 13,850 mm, total width: 2,550 mm, total height: 4,000 mm, suspension: air, tire size: 445/45 R19,5", tire condition: 100 %, color: original, Year of construction: 2026, Save on transport costs! Upon request, up to three curtainsider trailers can be delivered as a space-saving 3-unit stack. Roof and side curtains are supplied separately and can be easily installed after delivery. Benefit from significantly reduced transport costs. Customized transport solution Configure your Fliegl trailer according to your requirements. The shown vehicle is an example only. Production and equipment are customized according to customer specifications. #Chassis Fine-grain steel welded construction with "Preload" neck area reinforcement Fifth wheel plate with replaceable 2" kingpin Outer frame with Load-Lock profile for securing straps 24 t 2-speed landing gear, one-side operation Extendable rear ladder Aluminium side underrun protection Galvanized steel underrun protection Rear impact protection Lockable plastic toolbox, W=600 / H=425 / D=460 mm Storage box for fire extinguisher up to 6 kg #Axles + Suspension Disc brake axles Laser-measured axle and chassis alignment for reduced tyre wear and fuel consumption Air suspension 1st axle automatic lift axle with forced lowering and starting aid (activated by 3x brake operation) #Brake system Dual-line compressed air braking system Colour-coded brake lines for easy service Spring-loaded parking brake 2 non-interchangeable coupling heads at front, without connecting lines EBS electronic braking system with EBS socket at front Raise/lower valve Vehicle height increases by approx. 50 mm when lift axle is raised Vehicle driving stability system #Wheels and tyres 445/45 R19.5" steel rims, factory silver finish #Electrical system 24 V system, multi-chamber lights Yellow LED side marker lights White front position lights White/red rear lane marker lights 2 x 7-pin non-interchangeable sockets at front #Floor Approx. 30 mm phenolic plywood floor panels on longitudinal supports High point load capacity for forklift axle loads up to max. 7,100 kg Rear steel chequer plate flooring approx. 300 mm length Ljdpfxszmub Hs Akkohn #Front wall / Corner posts Height 2,580 mm Steel corner posts in high-volume design Side curtain release system at front wall "Crash Blocker" steel impact protection inside lower area (approx. 140 mm height) Front wall additionally covered inside with 1,250 mm high phenolic plywood panel #Centre posts 3 pairs of sliding posts, movable over full length With 4-fold insertion pockets and long lower pocket 3 post positions 4 rows of aluminium V-insertion slats #Rear wall / Corner posts Steel rear corner posts up to roof height Curtain attachment with round tube and tension ratchet Double-wing rear portal doors with 2 internal rotary bar locks each #Curtain Curtain with welded horizontal and vertical reinforcement belts Stainless steel tension buckles #Roof Sliding roof system with rear end lift function Roof opens from rear to front L-shaped roof beam for automotive industry applications Non-elastic roof with minimal deflection during loading and unloading Optimized rain gutter at rear, mounted on top rear cross member above doors EcoLift roof lifting system, height adjustable by approx. 380 mm on both sides with gas spring assistance Complete body supplied loose as a kit (unassembled).

Condition: used, axle configuration: 3 axles, first registration: 07/2013, suspension: air, tire size: 385/65, tire condition: 30 %, color: other, Equipment: ABS, = Additional options and accessories = - Air Suspension - BPW Axles - Disc brakes = More information = Lsdpfe Adrvyox Akkjhn Year of construction: 2013 Tyre size: 385/65 Make axles: BPW Brakes: disc brakes Suspension: air suspension Rear axle 1: Tyre profile: 30% Rear axle 2: Tyre profile: 40% Rear axle 3: Tyre profile: 40%

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,700 kg, maximum load weight: 33,300 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 9,600 mm, total width: 2,550 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, Year of construction: 2026, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer specifications. Chassis, Saddle, and Container Fine-grain steel welded construction, saddle plate with 2 replaceable kingpins and 2 kingpin positions Container receptacles: Rear extension retracted: 1 x 20 ft or 1 x 30 ft, flush at the rear Middle telescope, 1st stage, rear extension extended, 1st stage: 2 x 20 ft or 1 x 40 ft with and without gooseneck tunnel Middle telescope, 2nd stage, rear extension extended, 2nd stage: 1 x 45 ft with and without gooseneck tunnel, and with rear overload capability Middle telescope as a nested central tube frame with pin locking with height adjustment at the rear and foldable center supports for containers without a tunnel Container guides, front, pluggable and removable Plug-in adapter for front locking, to lock containers without a tunnel from below, with a holder when not in use Rear extension mounted on rollers, with hand crank 24 tons, 2-speed support jacks, single-sided operation Rear underrun protection, extendable for 45 ft containers Half-shell fenders with anti-splash flaps according to EG Rear impact protection Axles + Suspension SAF disc brake axles with 430 mm disc diameter Axle/suspension laser-aligned to reduce tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross vehicle weight Air suspension Braking System 2-line compressed air braking system Color-coded line routing for easy service Spring-loaded parking brake Tele Control Axle load adjustment for easy telescoping 2 fail-safe coupling heads at the front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connecting cable Note: The trailer may only be towed by tractor units that guarantee the effectiveness of the ABS! with raise and lower valve Vehicle - Driving Stability System Axle load detection via EBS-CAN bus signal, for display on the instrument panel in the driver's cab; the truck must be prepared accordingly; no truck installation (no calibrated scale) Wheels and Tires 385/55 R22.5, manufacturer's choice Steel rims, factory silver Electrical System 24 Volt, multi-chamber lights, tail and brake lights in LED, yellow LED lighting on the sides (Note: certain tractor units may experience false diagnoses, even though the function is correct) 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe sockets at the front, without connecting cable Operating Instructions Note: Transport of filled tank containers is not permitted! When transporting 45 ft containers with a short tunnel, with or without a front extension, the permissible system length from kingpin to the rear edge of the vehicle and the total length of the combination of 16500 mm will be exceeded! The rear underrun protection must be manually extended. An exemption permit according to § 70 StVZo is required! Country of Registration/ Signs Germany Type approval according to EG 2007/46 24/7 service hotline Ledpfx Aei Ri Exjkkehn prepared for license plate holder, single-line Warning sign according to ECE - 70 Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paint Frame, front section + rear extension, hot-dip galvanized Rear section DB 7350 Novagrau - 10-year guarantee against rust-through or hot-dip galvanized - 15-year

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,000 kg, maximum load weight: 15,000 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 6,930 mm, loading space width: 2,450 mm, loading space height: 1,300 mm, total length: 9,300 mm, total width: 2,550 mm, total height: 1,300 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, color: original, Year of construction: 2026, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example only. Production and equipment are customized according to customer specifications. # Chassis – Turntable Container Trailer Heavy-duty fine-grain steel welded construction Sliding container system: Container is loaded from the rear onto the sliding frame and pushed forward. Adjustable front container stop for 6.0 m, 6.5 m and 7.0 m roll-off containers with external rollers. Container locking system: * 2 pairs of recessed locking hooks * Pneumatic operation Heavy-duty turntable with ball-bearing ring. 2 wheel chocks with holders Aluminium side underrun protection Steel rear underrun protection Half-shell mudguards Vertical rear impact protection (left and right) with Delta rubber buffers 1 spare wheel holder with mounting kit Lockable plastic toolbox with drawer and shelf (650 × 520 × 670 mm) # Drawbar Drawbar with certified 40 mm towing eye # Axles + Suspension SAF disc brake axles Laser-measured axle/chassis alignment for reduced tyre wear and fuel consumption Air suspension with raise/lower valve # Wheels and Tyres 385/55 R22.5 tyres on factory silver steel rims # Brake System Dual-line compressed air braking system Spring parking brake Drive-away protection: parking brake is automatically activated when the container locking system is open Vehicle Stability System (VSS) 2 non-interchangeable air couplings with connecting lines to the towing vehicle Electronic Braking System (EBS) with front connector and connecting cable Note: Trailer may only be operated with towing vehicles that ensure full ABS functionality. Lhsdpfx Aszna Tdjkkjn # Electrical System 24 V electrical system Multi-chamber lighting Yellow LED side marker lights 2 white front position lights 2 white/red rear outline marker lights 2 LED rear work lights, activated via reverse gear 2 × 7-pin front connectors with connecting cable # Registration Prepared for registration in Germany DEKRA approval and certificate according to §13 EC-FGV 24/7 service hotline Prepared for single-line number plate holder ECE R48 reflective contour markings (white sides, red rear) # Finish Frame hot-dip galvanized with passivation or painted in customer's preferred colour Drawbar KTL-coated in black

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 5,600 kg, maximum load weight: 24,400 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 5,900 mm, loading space width: 2,520 mm, loading space height: 860 mm, total length: 10,290 mm, total width: 2,550 mm, suspension: steel, tire size: 235/75 R17,5", tire condition: 100 %, color: original, Year of construction: 2026, Tailor-made transport solution Configure your Fliegl vehicle to your requirements. The vehicle shown is an example. Production and specification are customised to customer requirements. #Low Loader Drawbar Trailer Chassis Welded steel construction Turntable with heavy-duty ball race Folding rear support legs Wheel chocks with holders Full-width rear mudflap 1 plastic toolbox Preparation for extensions to 3,000 mm (holes in outer frame with covers, not in rear bevel) #Lashing Points Low Loader 1 pair of recessed 10 t lashing cut-outs in front gooseneck side members 7 pairs of recessed 10 t lashing points in top and side outer frame 1 on front gooseneck 5 in low bed 1 in rear bevel 12 pairs of 5 t lashing holes in outer frame (for load straps) 5 on gooseneck, 6 in low bed and 1 in rear bevel #Drawbar Equipment Drawbar with certified 40 mm towing eye Spring-assisted drawbar height adjustment #Axles + Suspension Drum brake axles, manufacturer's choice "Achsen-/Fahrwerk laservermessen" reduces tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushes and mechanical axle load equaliser #Wheels and Tyres 235/75 R17.5 Manufacturer's choice Twin steel wheels, factory silver #Braking System Twin-line air brake system Spring parking brake 2 non-interchangeable front coupling heads with connecting lines to towing vehicle Connecting lines extended by approx. 60 cm Without ABS, with mechanical ALB, max. 60 km/h approval #Electrical System 12 V multi-chamber lights, without yellow side LED lights, with side reflectors 2 front white position lights 2 rear white/red outline marker lights 1 x 7-pin 12 V front plug with connecting cable, extended by approx. 60 cm Lhsdsznyrmepfx Akksn 1 removable LED beacon with bracket, switched via side lights #Floor Front gooseneck with steel chequer plate Recessed storage box in transition to gooseneck 70 mm softwood floor, steel chequer plate in wheel arch area Rear bevel with 70 mm softwood floor Low loader deck incl. rear bevel: 5,900 mm #Loading Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Timber-covered (steel chequer plate at ramp tips) Hydraulic operation via PTO with flow control, left-hand side operation in direction of travel Hydraulic connection with SVK plug NW 10/3 incl. connecting hose #Registration / Plates Registration country: Germany With DEKRA inspection and approval report for max. 60 km/h registration, agricultural towing vehicle Prepared for two-line number plate holder Without contour marking / reflective strips according to ECE R 048 #Paint Finish Chassis hot-dip galvanised incl. passivation "15 Jahre Gewährleistung gegen Durchrostung" Drawbar galvanised or black, manufacturer's choice Loading ramps hot-dip galvanised

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 1,850 kg, maximum load weight: 8,650 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 3,100 mm, loading space width: 1,740 mm, total length: 4,900 mm, total width: 2,550 mm, suspension: steel, tire size: 235/75 R17,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your individual requirements. The vehicle shown is an example configuration. Production and equipment are tailored to customer specifications. ### Chassis – Tandem Low-Bed Trailer for Skip Containers * High-tensile steel welded chassis construction * 1 pair of adjustable and removable skip container locking wedges * 1 pair positioned in front of the container * Lashing rails for skip containers on both sides of the body * Front jockey wheel * Steel mudguards covering both wheels * Aluminium side underrun protection * 2 wheel chocks with holders * Recessed rear storage compartment integrated into the floor, approx. 650 × 240 × 240 mm (W × L × D), with slightly raised lid ### Drawbar * Drawbar with certified 40 mm towing eye ### Axles & Suspension * 2 Euro axles (manufacturer's choice) with tapered roller bearings and S-cam drum brakes * Laser wheel alignment of axles and suspension for reduced tyre wear and lower fuel consumption * Parabolic leaf suspension with maintenance-free steel-rubber bushings and mechanical load equalisation (walking beam system) ### Wheels & Tyres * 235/75 R 17.5 tyres * Manufacturer's choice * Steel rims, factory silver finish ### Braking System Lsdpfxjzhfzgj Akkshn * Dual-line compressed air braking system * Spring-loaded parking brake * Two non-interchangeable coupling heads at the front with connecting lines to the towing vehicle * 24 V ABS and automatic load-dependent braking (ALB), with front ABS connector and connecting cable Note: The trailer may only be operated with towing vehicles that ensure proper ABS functionality. ### Electrical System * 24 V electrical system * Multi-chamber rear lights * Yellow LED side marker lights * 2 white front position lights * 2 white/red rear outline marker lights * 2 × 7-pin non-interchangeable front connectors with connecting cable ### Low-Bed Body (TTS) * Low-profile steel well body * Steel floor plate * Steel side walls fully welded to the floor for maximum durability Note: Minor floor distortion caused by the welding process is technically normal. ### Registration & Compliance * Registration country: Germany * DEKRA inspection and certification included (according to §13 EC-FGV) * 24/7 service hotline * Prepared for single-line licence plate holder * Reflective contour markings according to ECE R048 (white on the sides, red at the rear) ### Paint Finish * Chassis painted in customer's colour * Drawbar painted to match the chassis --- Customized Transport Solution Configure your Fliegl vehicle according to your individual requirements. The vehicle shown is an example configuration. Production and equipment are tailored to customer specifications.

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT23202019236, empty load weight: 5,675 kg, overall weight: 31,000 kg, axle configuration: 2 axles, first registration: 10/2026, loading space length: 13,650 mm, loading space width: 2,480 mm, total length: 13,850 mm, total width: 2,550 mm, total height: 4,030 mm, suspension: air, tire size: 435/50 R19,5", color: yellow, Year of construction: 2016, Fine-grain steel welded construction, fifth-wheel coupling plate with replaceable 2" kingpin - Slightly inclined outer frame with "Load-Lock-Profil" for securing straps - Note: When securing straps in conjunction with side boards, the side boards must be opened! - Single-side operation of landing legs, straight lower section, without thrust compensation - Side-mounted door retainers, aluminium side underrun protection, galvanised steel rear underrun protection - Heavy-duty pallet stop on both sides, approx. 20–25 mm high, lashing points every 200 mm; loading height reduced by approx. 20–25 mm - Spare wheel, same make as standard tyres - Plastic toolbox with drawer and shelf, W=650 / H=520 / D=670 mm, lockable with a padlock (padlock not included) # Axles and suspension - BPW disc-brake axles - Air suspension # Braking system - Dual-line compressed-air braking system - Spring-loaded parking brake - 2 misconnection-proof coupling heads at the front, without connecting lines - EBS electronic braking system with front EBS socket, without connecting cable - Warning: This trailer may only be towed by tractor units that ensure the effective operation of the ABS! - With raise/lower valve - Vehicle driving stability system # Wheels and tyres - 435/50 R19.5", make at manufacturer's discretion # Electrical system - 24 V, multi-chamber lights, yellow LED side lighting - Yellow LED side lighting with 20 LEDs per lamp - 2 white front position lights - 2 white/red rear outline marker lights - 2 x 7-pin and 1 x 15-pin misconnection-proof sockets at the front, without connecting cable - LED safety light, mounted at the top of the rear corner posts - Approx. 30 mm thick screen-printed floor panels, cross joints with Omega inserts, on longitudinal bearers for high point loads; maximum forklift axle load 7,100 kg # Front bulkhead / corner posts - 2,580 mm high, steel corner posts in high-volume design # Centre posts - Pair of sliding posts, movable along the full length, with four-way sockets and a long lower socket - Pair of post positions Lhedpfx Ao Aay Sbskksn # Insert boards - 4 rows of aluminium V-shaped insert boards # Rear wall / corner posts # Curtain - Curtain with welded-in horizontal and vertical tensioning straps # Roof - Sliding roof, rear end lift-up section; roof can be slid from rear to front; L-shaped roof rail for the automotive industry; internal width between roof rails approx. 2,490 mm; curtain colour: white - EcoLift lifting roof, raises by approx. 380 mm, assisted by gas struts - Front with 2 driving positions: - Front internal height approx. 2,900 mm / 3,000 mm # Operating instructions - If the overall height exceeds 4,000 mm, please note the following: - The transport operator is solely liable for any resulting damage. - The driver transporting the vehicle must obtain a permit under Section 29 of the German Road Traffic Regulations (StVO). - We accept no liability for transporting the vehicles. - Note: The specified gross weight is technically possible; depending on the load, it may not be achievable while complying with the permitted axle and fifth-wheel loads. # Registration / plates - Germany - With DEKRA inspection and report - Load securing certificate to EN 12642 XL (valid only in conjunction with 4 rows of aluminium boards) - Additional DC 9.5 certificate, pallet stops on both sides, approx. 25 mm high; loading height reduced by approx. 25 mm; warning panel to ECE Regulation 70