Low deck

Faymonville MAX Trailer-3-Achs-Mega-Tele-Plateau-nachlaufgel.

Condition: new, empty load weight: 8,300 kg, maximum load weight: 36,700 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 13,600 mm, loading space width: 2,540 mm, loading space height: 1,080 mm, suspension: air, tire size: 385/65 R 22.5, color: grey, Equipment: ABS, tail-lift, Cargo bed: Cargo bed in extendable design with pneumatically operated locking mechanism Cut-outs in the outer frame of the cargo bed for attaching tensioning straps Seat posts: JOST fifth-wheel supports (mechanical) with 2-speed gearbox for 24 t lifting load Axles and tires: BPW axles, air-sprung, with disc brakes (430 mm), with raise/lower function The self-steering axle with electromagnetic reverse lock can be activated via reverse gear or manually Axle tool 385/65 R 22.5 tires Fjdpoikyh Hjfx Ah Djpc Brake system: WABCO brake system in accordance with EU regulations with EBS-E Paint finish: First-class and long-lasting corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component top coat in a single color in MB 7350 nova grey Rear section metallized and painted in RAL 9010 Metallic paint is not possible Steel construction: Steel construction made from high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Electrical system: Electrical system according to EU regulations Lighting 24 Volt ASPÖCK-NORDIK ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO Accessories included: Yellow-red air couplings on the galvanized connection strip at the front One galvanized steel end wall approx. 1,600 mm high. EN12642-XL 4 restraint shoes with bracket White reflective tape in accordance with EU regulations on the sides, on the extension and at the rear in red European reflector plates at the rear of the trailer Loading area with approx. 30 mm thick hardwood floor edged in omega profiles 10 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed 1 spare wheel holder under the cargo bed on the right in the direction of travel Manual and description A bracket for a rotating beacon at the rear of the trailer A holder for the warning signs including socket on the gooseneck and on the rear plate on the left and right respectively A layer of sand painted onto the central beam to prevent slipping 6 pairs of WADER container pockets in the loading area, for 1x 20ft container, 2x 20ft containers or 1x 40ft container in the pull-out, an additional locking point is provided for a 45ft container 4 pairs of stanchion pocket rails, mounted transversely in the loading area, for 100 x 50 mm stanchions One galvanized bracket transversely under the cargo bed 2,390 x 720 x 400 mm Access ladder mounted on the right in the direction of travel Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status Load manometer for determining the axle loads including load diagram HRM metallization of the outer frame Complete steel construction shot-peened, then the defined visible surfaces hot-finished in metallization with ZINACOR 850

Condition: new, empty load weight: 17,250 kg, maximum load weight: 48,700 kg, overall weight: 66,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,480 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 17,250 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and removed hydraulically -For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Low bed: -Low bed with external supports, designed as a telescopic tank bridge in low construction with extension at the front -Length x width approx. 7,550 mm x 2,740 mm -Mechanical locking of the extension Chassis: -Chassis at the rear with closed outer frame -Checker plate covering and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, suspension and tires: -"PENDEL-AXLE", all axles hydromechanically forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position Fpodjh Hm Tzjpfx Ah Djc -Final painting of axles with 2 layers of 2-component paint in a single color in "FAY-Gray-34-0260" -Technical axle load 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 Accessories: -Steel bulkhead, plug-in, approx. 400 mm high -4 wheel chocks -Gooseneck in the rear upper area closed with a removable cover -1 pair of steel ramps with climbing strips and fastening bolts to bridge the hooks of the low bed -The ramps can be placed over or between the hooks -Fastening options for the steel ramps at the rear between the outer supports of the gooseneck -One Locking point approximately every 1,000 mm on the extension -1 lashing ring on the left and right on the front cross member -Connection strip for supply lines to the tractor unit, attached at the height of the outer frame profile -6 pairs of threaded blocks on the outside of the inner supports of the loading area for mounting screwable rings M24 -6 pairs of countersunk lashing rings on the outside of the outer supports of the loading area, foldable inwards and outwards -1 pair of threaded blocks at the front and rear of the outer supports of the loading area for mounting screwable rings M24 -Hanging strip for loose aluminum loading ramps on the vehicle's end cross member -Central lubrication system with 2 pumps, BEKAMAX brand -Steering from the front and rear, operated by cable remote control, with alignment control of the axles -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Removable loading floor (galvanized) in 3 elements can be inserted between the outer supports with hardwood flooring -Foldable extensions, by approx. 230 mm per side -Extension planks, loose, framed in steel -4 warning signs approx. 423 x 423 mm -Radio remote control for operating the steering -3.5" king pin -Anti-slip sticker on the left bevel of the gooseneck -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Guide plate from the gooseneck for the fifth wheel plate, approx. 800 mm wide -1 spare wheel with mounting adapter -Parking position on the gooseneck for the warning signs when not in use -2 pairs of stake pockets embedded in the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm -Dipper handle recess of the rear chassis closed at the back with a plug-in plate -Color of the trailer MB 7350 Novagrau

Condition: new, maximum load weight: 49,000 kg, overall weight: 60,800 kg, axle configuration: > 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area in extendable version: -Loading surface in extendable version with rear bevel of approx. 1,000 mm x 8° -5 pairs of lashing rings can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps. (LC 2,000 daN) -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Removable two-part ramps: -A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable -Maximum load per pair: 40,000 kg Fpedpjh Etf Refx Ah Dsc Seat posts: -JOST fifth wheels (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles, two axles rigid two axles self-steering, air-suspended, with drum brake, with lifting/lowering function The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -axle tool -235/75 R 17.5 tires Brake system: -brake system in accordance with EU regulations with EBS-E (4S3M) Steel construction: -steel construction made of high-strength fine-grained steels -Steel grades: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Coating: -First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in nova grey Electrical system: -Electrical system in accordance with EU regulations, 24 volt ASPÖCK-NORDIK lighting (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Accessories included: -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -One spare wheel with holder in front of the bulkhead -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon -Cover plates to bridge the gap between ramps and cargo bed -White reflector tape in accordance with EU regulations on the sides, on the extension and red at the rear -Electric hydraulic unit -On the gooseneck and on the ramps on the left and right a holder for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -One mud flap at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -4 pairs of WADER container pockets in the loading area for one 20ft, 2x 20ft or one 40ft container -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -Lift axle on the front axle with controls -Square climbing rails 20 x 20 mm -BEKAMAX central lubrication system -Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm

Condition: new, empty load weight: 22,700 kg, maximum load weight: 79,300 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, loading space length: 11,000 mm, loading space width: 2,850 mm, loading space height: 920 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 22,700 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the length of the loading area, length approx. 3,750 mm, with a bevel at the rear of approx. 850 mm x 10° -Can be raised and lowered hydraulically, stroke +- 250 mm including hydraulic connection connected to the hydraulic axle compensation of the first two axles -Open in the rear third -For tractor units: 6 x 4 and 8 x 4 Loading area: -Loading area in extendable design, length approx. 11,000 mm with a bevel at the rear of approx. 500 mm x 10°. -A recess in the loading area and in the bevel to accommodate the excavator bucket handle approx. 4,240 x 900 x 440 mm -Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable supports and automatically adjust to the respective loading area length Ramps: -A pair of two-part steel ramps with a length of approx. 4,650 mm and a width of approx. 900 mm -Hydraulically foldable ramp tips. -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards -25 mm "Super Grip" rubber floor and approx. 5 mm sheet metal floor as additional reinforcement on the slope of the loading area -20x30 mm square climbing rails, approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: -PA-X axle system, all axles hydro-mechanically forced steered -The steering behavior of the first two axles can be optimally adjusted to the length of the loading area both mechanically and hydraulically. -Hose rupture valve on the axle compensation cylinder with automatic RESET function. -Hydraulic cylinder with shut-off valves and pins for securing in the raised position. -245/70 R 17.5 3PMSF Accessories included: -Steel bulkhead, pluggable, approx. 400 mm high -Connection strip for supply lines to the tractor unit, mounted at the height of the outer frame profile -1 spare wheel -Outer support of the gooseneck with mounting holes for screwable lashing rings -The first hole approx. 200 mm from the front, then approx. every 400 mm -2 pairs of screwable lashing rings included -Checker plate covering above the gooseneck -On the gooseneck 1 pair of pluggable aluminum side walls on the side, approx. 400 mm high, anodized -On the gooseneck a pluggable aluminum rear wall, approx. 400 mm high, anodized -3.5" kingpin / 2" kingpin mounted -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -4 Brake shoes -4 axle load gauges -Mechanical downpipe supports at the front -1 one-piece INOX tool box, approx. 2,480 x 340 x 390 mm -Mechanical downpipe supports at the front Fpsdpjk Af Svjfx Ah Dec -Continuous sheet metal covering on the loading area with a painted layer of sand to prevent slipping -1 intermediate table, approx. 500 mm wide, for the pull-out, with long holes for hanging and movable bridging elements -Painted sand coating on the support surfaces of the intermediate table -Mechanical locking for locking the intermediate table to the pull-out -8 pairs of stake pockets in the outer frame -Extensions (galvanized) extendable by approx. 230 mm per side -1 pair of hydraulic. Rear supports -Central lubrication system -1 reversing light on the left and right at the rear of the vehicle -3 kW electro-hydraulic unit -Widening planks, loose, in reinforced steel U-frame -Radio and cable remote control -4 warning signs, approx. 423 x 423 mm

Condition: used, empty load weight: 10,900 kg, maximum load weight: 43,600 kg, overall weight: 54,500 kg, axle configuration: > 3 axles, first registration: 04/2025, loading space length: 8,700 mm, loading space width: 2,550 mm, loading space height: 855 mm, tire size: 245/70 r17.5, color: grey, Year of construction: 2025, operation weight: 10,900 kg, Equipment: ABS, Gooseneck, rigid, in center tube design: -closed outer frame with cut-outs for lashing straps (LC 1,500 daN) -steel floor covering with anti-slip coating -including perforated strip for aluminum docking lights -2" kingpin -Mechanically operated BPW seat posts -550 mm long, 8' chamfer at the gooseneck end -Front wall incl. parking position for rear wall, 400 mm high -Spare wheel holder mounted upright on the front of the gooseneck -3 pairs of LC 5,000 daN lashing rings recessed in the loading area of the gooseneck -Aluminium plug-in drop sides 400 mm high, consisting of 2x drop sides, side length 3,150 mm and rear drop sides with stanchions (galvanized) -Rectangular storage box, aluminum, hinged lid, lockable Dimensions approx. 400 x 800 mm, center -Storage box 45', aluminum, hinged lid, lockable Dimensions approx. 400 x 800 mm, left -Storage box 45', aluminum, hinged lid, lockable Dimensions approx. 400 x 800 mm, right Loading area, easily telescopic: -closed outer frame with cut-outs for tension belts (LC 1,500 daN) -Fixed part at the front 700 mm Sheet metal floor covering with anti-slip coating -Angled interface between fixed section and loading area for attaching bridging rails and wheel recesses -Excavator trough incl. slotted holes for load securing (LC 1,500 daN), length approx. 3,850 mm -Preparation for hydraulic ramp (electrical supply) -spars for widening to 3,000 mm -Sloping vehicle rear 8°, 550 mm long -Carriage design for easy attachment and removal of ramps -Continuous mud flap at the rear -1 pair of LC 10,000 daN lashing points in the middle of the cargo bed behind the gooseneck -7 pairs of LC 10,000 daN lashing points in the outer frame of the cargo bed -6 pairs of stanchion pockets 100 x 50 mm in the outer frame of the cargo bed -1 pair of LC 10,000 daN lashing points in the center of the rear area of the cargo bed -1 pair of stanchion pocket strips approx. in the middle of the cargo bed -1 pair of stanchion pocket rails on the fixed part -1 pair of stanchion pocket rails behind the last axle Ramps: -Hydraulic double folding ramps, 2,750+1,500x800 mm -Wooden decking larch -Control via remote control (possible via cable and radio) -Ramps with quick-change (disassembly) system Chassis: -axle make BPW ECO Max -2 ride heights -4 axles 10 t each (technically 12 t) -Twin tires 245/70 R17.5 -2 x rigid axle and 2 x friction-steered axle -Reverse steering lock on the friction-steered axle via reverse gear -Knorr brake system (in accordance with EU regulations with EBS-E) -TIM G2 from Knorr (trailer information module) -RSS (Roll Stability Support) driving stability control Load-dependent lift axle on the first axle incl. start-up aid (forced lowering of the lift axle possible via TIM) Accessories: -4 wheel chocks with holder 2 pairs of warning signs 423 mm x 423 mm, with 2 position lights and plug-in position for rotating beacon, infinitely adjustable up to 3,950 mm Fodpfei Ai E Rsx Ah Depc -Fastening options on the gooseneck and on the loading area (alternatively on the ramp, if available) are included -pluggable bulkhead plate at the end of the excavator trough -Electro-hydraulic unit for ramp operation -Ramp operation via radio remote control -Hydraulic relief supports at the rear of the vehicle for support during the loading process -1 Pair of additional reversing lights rear switched to reverse gear -Wooden widening planks - larch (optional)

Condition: new, maximum load weight: 38,953 kg, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2025, MAX100-N-3B-9.30-U Technical data Speed: 80 km/h Total weight: 49,500 kg Fifth wheel load: 18,000 kg Axle load: 31,500 kg Empty weight (+/- 3%): 10,547 kg Payload approx.: 38,953 kg Gooseneck length: 3,850 mm Fifth wheel height loaded: 1,200 mm Loading area length: 9,300 mm Extendable by: 0 mm Axle spacing: 1,360 mm Rear steering radius: 2,300 mm Loading height with max. load: 860 mm Total width: 2,540 mm Suspension travel: -55/ +145 mm Technical description Gooseneck: Gooseneck with bevelled corners 45° at the front and with a rear bevel of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring 30 mm thick. Loading area: Loading area can be raised and lowered hydraulically after the gooseneck, length approx. 2,800 mm, with a rear bevel of approx. 1,000 mm x 8°. 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN). 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 1 pair of tension rings that can be folded inwards on the central support at the front (LC 10,000 daN). Cutouts in the outer frame of the loading area for hanging tensioning straps. (LC 2000 da N). Hardwood flooring approx. 48 mm thick, checkered sheet flooring over the axles. Ramps: Two-part steel ramps A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood flooring. Ramp with hydraulically foldable and unfoldable ramp sections, hydraulic lifting mechanism and hydraulically movable. Maximum load per pair: 40,000 kg Seat supports: JOST seat supports (mechanical) with 2-speed gearbox for 24t lifting load (50t test load). Tires: 235/75 R 17.5 tires as selected by the manufacturer. Axle: SAF axles, air-sprung, with drum brake, with lifting/lowering function. The last axle is self-steered with an electro-magnetic reversing lock can be activated via reverse gear or manually. Axle tool. Braking system: Braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel construction: Steel construction made of high-strength fine-grain steel. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) top coat in a single color in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint possible. Electrical system: Electrical system in accordance with EU regulations, lighting LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the connection panel at the front with sockets 24N, 24S & 15-pin. Connection in accordance with ISO. 24N ISO-1185 Fpjdpfx Asg Sk Trjh Dec 24S ISO-3731 15-pin ISO-12098 Accessories included 2" kingpin A galvanized steel bulkhead approx. 400 mm high. Yellow-red air couplings on the galvanized connection strip at the front. 4 pieces of chocks with holder on the bulkhead. (± 5kg) Cable for supplying the electro-hydraulic unit and/or the electric cable winch (35mm², 3.5 m long, max. 250A) between the trailer and tractor unit with plug connection (ANDERSON-ANDERSON) Galvanized folding supports under the slope of the loading area. A bracket for a rotating beacon at the rear of the trailer. Control valves for the ramps attached to the right-hand side of the trailer. (± 4kg) Yellow reflector tape in accordance with EU regulations on the side and rear of the Trailer.

Condition: new, empty load weight: 15,420 kg, maximum load weight: 61,080 kg, overall weight: 76,500 kg, axle configuration: > 3 axles, loading space length: 8,600 mm, loading space width: 2,540 mm, loading space height: 900 mm, tire size: 235/75/r17,5, color: grey, Equipment: ABS, Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10° 3 pairs of lashing rings Hardwood decking 30 mm thick Loading platform: Loading area in extendable design with rear bevel of approx. 500 mm x 8° 8 pairs of lashing rings can be folded outwards Fjdpfx Ajl Sl Izeh Dspc 1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking. Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable. Maximum load per pair: 50,000 kg. Seat posts: - JOST fifth wheels (mechanical) with 2-speed gearbox for 24t lifting load (50t test load). Axles and tires: BPW axles and suspension, 4th + 5th axle self-steering Technical axle load: 12,000 kg 4th and 5th axles with electro-magnetic reverse lock via reverse gear and manual activation Tires 235/75 R 17.5 3PMSF Brake system: Brake system in accordance with EU regulations with EBS-E (4S3M) Sockets and lighting: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO 24N ISO-1185 24S ISO-3731 15 pole ISO-12098 Paint finish: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in MB 7350 nova grey Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Steel construction: Steel construction made from high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Accessories: One spare wheel with holder in front of the bulkhead 2" kingpin One galvanized steel bulkhead approx. 400 mm high Yellow-red air couplings on the galvanized connection strip at the front 2 restraining shoes with holder on the bulkhead Mounting in the rear area of the gooseneck for ALU docking lights A bracket for a rotating beacon at the rear of the trailer Galvanized supports under the bevel of the loading area White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear Electro-hydraulic unit at the rear under the cargo bed A holder for the warning signs, including a socket, on the gooseneck and on the rear panel on the left and right respectively Control valves for the ramps mounted on the right-hand side of the trailer A mud flap at the rear of the trailer Manual and description on USB stick 3.5" kingpin supplied loose ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm (LxH) The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) 3 pairs of WADER container pockets in the loading area for a 20' (30') or a 40' container 6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed Galvanized extensions, extendable by approx. 230 mm per side Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope On the chequer plates, above the kingpin and the load floor

Condition: new, empty load weight: 10,700 kg, maximum load weight: 38,800 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r 17,5, color: grey-black, Equipment: ABS, Gooseneck: •Gooseneck with bevelled corners at the front 45° and with a rear bevel of approx. 750 mm x 10° •3 pairs of lashing rings •Hardwood flooring 30 mm thick Loading area in extendable version: •Loading area in extendable version with rear bevel of approx. 1,000 mm x 8° •Cutouts in the outer frame of the loading area for hanging tensioning straps •Hardwood flooring approx. 48 mm thick, checkered sheet covering over the axles Two-part steel ramps: •One pair of galvanised, two-part steel ramps with approx. 48 mm thick hardwood flooring •Ramp with hydraulically foldable and unfoldable ramp parts, hydraulic lifting mechanism and hydraulically movable •Maximum load per pair: approx. 40,000 kg Axles and Tires: •BPW axles and suspension, 2 axles rigid, 1 axle with self-steering •Technical axle load: 12,000 kg •Electro-magnetic reversing lock can be activated via reverse gear and manually •Air suspension with lifting and lowering valve •Axle tool •235/75 R 17.5 3PMSF Brake system: •WABCO brake system in accordance with EU regulations with EBS-E Fpsdpshlz S Nofx Ah Doc Paintwork: •First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component zinc dust primer •A high-quality 2-component top coat in one color in MB 7350 Nova gray •Rear section metallized and painted in RAL 9010 Seatposts: •JOST seatposts with 2-speed gearbox for 24t lifting load (50t test load). Steel construction: •Steel construction made of high-strength fine-grain steel •Steel qualities: •S355J2+N/S355MC •S690QL/S700MC Electrical system: •Electrical system in accordance with EU regulations, 24 volt lighting •ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets Accessories included: •A spare wheel with holder •A galvanized steel bulkhead approx. 400 mm high •Yellow-red air couplings on the galvanized front connection panel •4 wheel chocks •A bracket for a rotating beacon at the rear of the trailer •Mounting in the rear area of the gooseneck for aluminum docking ramps •Galvanized folding supports under the bevel of the loading area •Cover plates to bridge the space between the ramps and the loading area •White Reflective tape in accordance with EU regulations on the side, on the extension and at the rear, red •Electro-hydraulic unit at the rear, under the loading area •A holder for the warning signs including a socket on the gooseneck and on the ramps on the left and right •Control valves for the ramps attached to the right-hand side of the trailer •ALU side walls and rear wall on the gooseneck, approx. 2,440 x 400 mm •The rear, galvanized plug-in stanchions are removable (length of the structure approx. 2,560 mm) •Four warning signs extendable by approx. 400 mm with a position light •3 pairs of WADER container pockets in the loading area for a 20ft, 30ft or 40ft container •6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading area •Galvanized extensions, extendable by approx. 230 mm each Page •Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area bevel •A painted layer of sand on the checker plates, above the kingpin and the loading area as anti-slip protection •Load pressure gauge for determining the axle loads including load diagram •HRM metallization (High Resistance Metallization) of the outer frame •Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: new, maximum load weight: 34,660 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our entire range of vehicles, including those available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment details available on request. Loading area: * Loading platform in double-extendable design with pneumatically operated locking mechanism * 2 pairs of recessed lashing rings (LC 5,000 daN) * 1 pair of recessed lashing rings (LC 10,000 daN) * 7 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * Cutouts in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) Landing gear: * JOST landing legs (mechanical) with 2-speed gearbox, approx. 24 t lifting capacity (approx. 50 t test load) Tyres: * Tyres 235/75 R 17.5 3PMSF – manufacturer of our choice Axles: * BPW axles, hydro-mechanically forced steering * Air suspension with lift and lower valve * Axle tool kit Brake system: * Brake system compliant with EU regulations, with EBS-E (2S2M), without connecting lines to the tractor unit Steel construction: * Steel structure made from high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paintwork: * Top quality, long-lasting corrosion protection of the standard shot-blasted welded chassis, guaranteed by a 2-component (2K) zinc dust primer * High-quality 2-component (2K) top coat, single-colour in RAL 3002 carmine red * Rear section metallised and painted in RAL 9010 (pure white) * Wheel rims in silver * Metallic paintwork not possible Electrical system: Fpedpfsk Ugacsx Ah Dec * Electrical system in accordance with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets; connections according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Including accessories: * Remote steering from front and rear via cable remote control with push buttons, with single-track axis control (without installation in the tractor unit) * Electro-hydraulic power unit * 4 wheel chocks with bracket on front wall * 2-inch king pin * Yellow-red air couplings on galvanised front connection panel * Yellow reflective tape according to EU regulations – on the sides, on the sliding extension and at the rear of the trailer * European reflective warning plates (red-yellow) at the rear of the trailer * One mudflap at the rear of the trailer * Manual and documentation on USB stick * Loading area with heavy-duty hardwood floor * 10 pairs of stake pockets for plug-in stakes, 100 x 50 mm, in the outer frame * Bracket for rotating beacon at the rear * Galvanised supports under the loading area taper * Bracket for rotating beacon at the rear * Hook-in profile for ALU loading ramps at the rear of the vehicle * 80 km/h speed stickers, rear and both sides * Load gauge for axle load determination, including load chart * Galvanised steel front wall (EN12642-XL), approx. 1,600 mm high * Central lubrication system with 2 BEKAMAX (Pico) pumps, using standard grease NLGI-2 and removable guard around the pump * Spiral cable for powering the electro-hydraulic unit and/or electric winch (approx. 35 mm², approx. 3.5 m length, max. 250A) between trailer and tractor unit with connector (NATO-NATO) * Anti-slip sand layer painted onto the centre beam * 6 pairs of WADER container pockets in the loading platform, for 1 x 20' container, 2 x 20' containers, or 1 x 40' container; in the extension, an additional ...

Condition: new, empty load weight: 6,350 kg, maximum load weight: 38,650 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 13,600 mm, loading space width: 2,540 mm, suspension: air, tire size: 385/65 R22,5, Equipment: ABS, Loading area: -2 pairs of lashing rings can be folded outwards (LC 5,000 daN) 24 pairs of cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) Seat posts: -JOST fifth-wheel supports (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles, air-sprung, with disc brakes (430 mm), with lifting/lowering function -385/65 R 22.5 tires Brake system: -WABCO brake system in accordance with EU regulations with EBS-E (2S2M) Paint finish: -First-class and long-lasting corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in MB 7350 nova grey -Rear part metallized and painted in RAL 9010 (pure white) -No metallic paint finish possible Steel construction: -steel construction made of high-strength fine-grained steels -Steel qualities: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690Mpa) Electrical system: -Electrical system according to EU regulations -Lighting 24 Volt -ASPÖCK-NORDIK (ASS3) -ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets -Connection according to ISO. -24N ISO-1185 -24S ISO-3731 -15-pin ISO-12098 Accessories included: -Yellow-red air couplings on the galvanized connection strip at the front -4 pieces of restraining shoes with bracket -2" kingpin -One galvanized steel end wall approx. 1,600 mm high. EN12642-XL -White reflector tape in accordance with EU regulations on the side of the trailer and red at the rear -European reflector plates (red/yellow) at the rear of the trailer -Loading area with approx. 30 mm thick hardwood floor edged in omega profiles -10 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -3 pairs of stanchion pocket rails, mounted transversely in the cargo bed, for 100 x 50 mm stanchions -Storage for 1,000 mm stanchions, at the rear in the central support -1 Spare wheel holder under the cargo bed on the right in the direction of travel -One mud flap at the rear of the trailer -Manual and description on USB stick -One bracket for a rotating beacon at the rear of the trailer Fodeiu Etkepfx Ah Dopc -One bracket for the warning signs on the gooseneck and on the rear panel on the left and right, including socket -6 pairs of WADER container pockets in the loading area, for 1x 20ft container, 2x 20ft containers or 1x 40ft container. Flush with the rear -Speed stickers 80 km/h at the rear and on both sides -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with one LED position light -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)