Low loader semitrailer

Doll 2-Achs-Tiefbett-tera-Pendelachsfahrwerk

Condition: new, empty load weight: 12,900 kg, maximum load weight: 34,100 kg, overall weight: 47,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,540 mm, loading space height: 350 mm, suspension: other, tire size: 245/70 R 17,5, color: grey, operation weight: 12,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered hydraulically and removed -Technical fifth wheel load: 23,000 kg -For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading area: -Low bed with external supports in extendable "SUPER LOW" design, length approx. 6,850 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking Rear chassis: -Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear -2 pairs of lashing rings that can be folded outwards -1 pair of lashing rings lying in the trough -2 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame Pendulum axle and tires: -"PENDEL-AXLE", all axles hydromechanically forced steered -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint, painted in a single color in "FAY-Gray-34-0260" -Technical axle load: 12,000 kg -Hydraulic axle compensation -Tires 245/70 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories: -Preparation for screw-on container positioning for 1x 20ft or 1x40ft container on the outer supports -2" kingpins -A galvanized steel front wall approx. 400 mm high -One spare wheel -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Electro-hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and at the rear -European reflector signs (red-yellow) on the rear of the trailer Nodpfx Alehlz R Soqela -One holder for the warning signs including a socket on the gooseneck and on the rear panel on the left and right -6 pairs of threaded blocks between the lashing rings under the top strap on the outer support for mounting screwable RUD rings VLBG-4 -ALU side walls and rear wall can be plugged into the gooseneck approx. 2,440 x 400 mm -The rear galvanized plug-in stanchions are removable (Length of the body approx. 2,560 mm) -Gooseneck in the rear upper area closed with a removable cover -5 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Foldable extensions, approx. 230 mm per side -2 pairs of screwable RUD rings VLBG-4 M24 (LC 8,000 daN) -1 pair of steel ramps to bridge the hooks of the low bed -A painted layer of sand on the loading area as anti-slip protection -Speed sticker 80 km/h at the rear and on both sides -Dipper handle recess of the rear chassis closed at the rear with a plug-in plate -Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm -Radio remote control for the steering in addition to the cable remote control, with indicator lights on the receiver as Alignment control -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 normal grease -Load pressure gauge for determining axle loads -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: new, maximum load weight: 30,190 kg, overall weight: 43,000 kg, axle configuration: 2 axles, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the equipment list. Full equipment details available on request. Loading Platform: - Lowbed with external beams in extendable SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking mechanism - Supply lines protected inside the extendable side rails, automatically adjusting to the current bed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for attaching RUD screw-on rings Gooseneck: - Gooseneck in SNT design for optimized platform length, length approx. 3,750 mm - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractors: 4x2, 6x2 Rear Chassis: - Rear chassis in short version with closed external frame and checker plate cover - Running gear with excavator recess, closed in the rear half to accommodate the air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings horizontal, front & rear of the chassis (LC 10,000 daN) Axles: Nljdpfx Aexarl Nslqea - BPW axles, hydro-mechanically forced steering - Technical axle load per axle: 12,000 kg - Air suspension with lift and lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF - Manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transmission to the truck via the standardized EBS interface in accordance with ISO 11992 - The truck must be capable of processing and displaying this data for correct operation Braking System: - Braking system according to EU regulations with EBS-E (2S2M) Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with indicators - ASPÖCK-UNIBOX at the front connection point with 24N, 24S, and 15-pin sockets as per standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel Construction: - Steel construction from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure is automatically shot-blasted after welding using a blasting turbine system - Second blasting process with corundum for optimal adhesion of coating system - HRM metallization of complete chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection - Final paint finish with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, as per RAL system 841GL - Rims in silver - Rear section metallized and painted RAL 9010 (Pure White) - Metallic paint not possible - Paint system tested in salt spray test as per ISO 9227-NSS - Cavities sealed with special wax Including the following additional equipment: - 2" King pin - One galvanized steel front wall, approx. 400 mm high - Remote steering of front and rear axles by cable remote control with pushbuttons, including single track axle monitoring (without installation in the tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Electro-hydraulic power pack - Preparation for mounting container locks for 1x 20' or 1x 40' container on the external beams - Without container locks

Condition: new, maximum load weight: 33,750 kg, overall weight: 47,000 kg, axle configuration: 2 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete range of vehicles, including those available for immediate or short-term delivery, on our website. Excerpt from the equipment list. Full specification available upon request. Neck: - Gooseneck in SNT design to optimize load platform length, approx. length 3,750 mm - Gooseneck hydraulically raisable/lowerable and detachable - Technical kingpin load: 23,000 kg For tractor units: 4 x 2, 6 x 2, and 6 x 4 Low bed: - Low bed with external beams, extendable SUPER LOW design, approx. length 6,850 mm - Low bed with fixed hardwood floor (approx. 40 mm thick) and mechanical locking - Supply lines run protected inside the extendable beams and adjust automatically to the respective bed length - 5 pairs of fold-out lashing rings (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for fitting bolted RUD rings Rear running gear: - Rear running gear with closed outer frame, checker plate surface, and continuous prism-shaped digger recess, approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of fold-out lashing rings (LC 10,000 daN) - 1 pair of laying lashing rings in the recess LC 16,000 daN - 1 pair of laying lashing rings in the recess LC 10,600 daN - 2 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame PENDLE-AXLE: - PENDLE-AXLE system, all axles forced-steered hydro-mechanically - Hose break valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins to secure in raised position - Axles finished with 2 layers of 2K paint, single-color painted in FAY-Grey-34-0260 - Technical axle load: 12,000 kg per axle, hydraulic axle compensation - Axle tools - Tyres: 245/70 R 17.5 3PMSF – Brand at our discretion. Load index (146/146F) TPMS: - TPMS tyre pressure monitoring system according to ECE R 141 Brake system: - Wabco braking system compliant with EU regulations, with EBS-E (2S2M), without connecting lines to the tractor unit Nsdpfjxbmn Uex Alqela Electrical system: - Electrical system per EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the turn signal - ASPÖCK-UNIBOX at the front connection panel with sockets 24N, 24S & 15-pin. Connection according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel structure: - Steel structure made of high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Painting: - Complete steel structure automatically shot-blasted after welding with a blast wheel system - Second blasting with corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for best corrosion protection - Final painting with 2 layers of 2K topcoat, single-color in RAL 3002 carmine red per RAL system 841GL Including the following additional equipment: - 2-inch kingpin - One galvanized steel front wall, approx. 400 mm high - Remote steering from front and rear via cable control with push buttons, including axle tracking control (without installation in tractor unit) - Electro-hydraulic power unit - 2 pairs of bolted container locks on the outer beams; includes 2 pairs of container locks for 1 x 20' or 1 x 40' container - On the gooseneck: removable aluminum side and rear walls, approx. 2,440 x 400 mm (L x H) - Rear galvanized plug-in stakes are removable

Condition: new, empty load weight: 12,800 kg, maximum load weight: 36,200 kg, overall weight: 49,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,550 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 12,800 kg, Equipment: ABS, Gooseneck: - Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm - Gooseneck hydraulically raised/lowered and removable - Technical fifth wheel load: 25,000 kg - For tractor units: 4 x 2, 6 x 2, and 6 x 4 Loading area: - Low bed with external supports, designed as a telescopic tank bridge in a low construction with a front extension - Length 6,850 mm x Width 2,540 mm - One locking point approximately every 1,000 mm on the extension Rear chassis: - Rear chassis with closed outer frame with checker plate cover and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear Axles, suspension, and tires: - "PENDEL-AXLE", all Hydro-mechanically forced-steered axles - Hose rupture valve on the axle balancing cylinder with automatic reset function - Hydraulic cylinder with shut-off valves and pins for securing in the raised position - Final axle painting with two coats of 2-component acrylic paint in a single color "FAY-Gray-34-0260" - Technical axle load: 12,000 kg Nsdpfxsvy Edcj Alqela - Hydraulic axle balancing - Tires: 245/70 R 17.5 - TPMS tire pressure monitoring system in accordance with ECE R 14 - TPMS tire pressure monitoring sensors installed in all wheels, including spare tires Accessories included: - Steel bulkhead, plug-in, approx. 400 mm high - 3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches - One spare tire with mounting adapter - Gooseneck outer support with mounting holes for screwable lashing rings -Slidable aluminum side walls on the gooseneck, approx. 400 mm high, anodized -Slidable aluminum rear wall on the gooseneck, approx. 400 mm high, anodized -Checker plate covering above the gooseneck -Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide -Illuminated control panel on the gooseneck with on/off switch -Hydraulic crossbar for supporting the gooseneck on the tractor unit or a dolly -2" kingpin -Anti-slip sticker on the left slope of the gooseneck -Gooseneck closed at the rear upper area with a removable cover -4 chocks with brackets -Hydraulic connections from the gooseneck to the drop bed with multi-coupling instead of screw couplings -1 pair of steel ramps with climbing rails and fastening bolts for bridging the drop bed's hooks -The Ramps can be installed over or between the hooks. -Attachment option for the steel loading ramps at the rear between the outer supports of the gooseneck. -Prepared for screw-on container holders for 1x20f on the outer support. -Mechanical bolt-and-lug coupling from the low bed to the chassis, for replacing the loading area or installing extension supports. -With electro-pneumatic-hydraulic couplings. -The outer supports of the low bed are provided with a painted layer of sand as a slip protection. -Removable loading floor (galvanized) in 3 elements, insertable between the outer supports with hardwood flooring. -Foldable extensions, by approximately 230 mm per side. -Hanging rail at the front of the rear chassis to the low bed for loose loading ramps. -2 pairs of stake pockets recessed into the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm. -Hanging rail for loose Aluminum docking ramps on the vehicle's end crossbar -Central lubrication system with 2 pumps -Wireless and cable remote control -4 warning signs, approximately 423 mm x 423 mm extendable -Extensive lashing positions

Condition: used, color: green, Year of construction: 2018, Faymonville F-S42-2ACB. Year: 2018. 12-ton Pendel-X axles. Max gross weight: 49,000 kg. Kingpin load: 25,000 kg. Hydraulic detachable gooseneck. Hydraulics operate on NATO connection from a truck. EBS, ABS, ALB. Spare wheel. Hydraulic suspension. Remote control via cable. Aluminium side boards and toolbox on neck. Extendable by 5.5 meters. Widened sections: 2 x 25 cm. Excavator trough: 2750 x 600 mm. Zinc-coated. Dimensions: Neck: L: 3650 mm W: 2500 mm H: 1550 mm Kingpin height: 1250 mm Deck: L: 8000 mm W: 2550 mm H: approx. 350 mm Deck thickness: 220 mm Rear of trailer: L: 2750 mm W: 2550 mm H: 1000 mm Tyres: 245/70R17.5, 80% tread remaining German trailer! ID No: 465. The General Terms and Conditions of Heinhuis apply to all advertisements, offers, and quotations by Heinhuis, all agreements entered into by Heinhuis, and the negotiations preceding them. By responding in any way, you accept the applicability of the General Terms and Conditions of Heinhuis and declare that you are aware of these Terms and Conditions. Our prices are net export prices. Nledey A Ehlopfx Alqja = Further information = Year of manufacture: 2018 Gross vehicle weight: 49,000 kg Extendable frame: Yes Price: On request = Company information = For more information: WhatsApp: