Low loader semitrailer

FAYMONVILLE Multimax Satteltieflader - hydr. gelenkt

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor Cjdjrgzv Njpfx Aaxsrb * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: new, empty load weight: 17,500 kg, maximum load weight: 43,500 kg, overall weight: 61,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,750 mm, loading space height: 400 mm, tire size: 245/70 R 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and lowered hydraulically -For tractor units: 6x4 or 8x4 Drop deck: -Low bed with external beams in extendable design, "SUPER LOW" design, length approx. 7,550 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking mechanism The supply lines are protected in the pull-out supports and automatically adjust to the respective drop-down bed length Rear chassis: -Rear chassis with closed outer frame, checker plate covering and continuous Prisma excavator trough approx. 1,450/900 x 505 mm, open at the rear -2 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame Axles and tires: -"PENDEL-AXLE", all axles with hydromechanical forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with stopcocks and locking pin for securing in raised position -Technical axle load: 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 / 3PMSF tires Accessories included: -Preparation for mounting bolt-on container positioners for 1x 20ft or 1x 40ft container on the outer beams -2" kingpin -One galvanized steel end wall approx. 400 mm high -One spare wheel with holder -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering can be operated from the front and rear by remote control cable via pushbuttons, with axle tracking control -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw coupling -Electric hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and red at the rear -2 wooden blocks 500x250x200 mm -European reflector plates (red/yellow) at the rear of the trailer -On the gooseneck and on the rear plate on the left and right, one holder each for the warning signs including socket -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 standard grease -Load manometer for determining the axle loads including load diagram -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,000 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,120 mm) -Separate air connection with air gun on the gooseneck -Duomatic air coupling from gooseneck to low bed -Gooseneck closed in the rear upper area with a removable cover -1 pair of steel ramps for bridging the mounting hooks of the low bed -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm -Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control 6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD rings VLBG-4 -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -folding extensions, approx. 230 mm on each side Crsdpoh Hm Thsfx Aaxjb -A layer of sand painted onto the loading surface to prevent slipping Dipper arm recess of the rear chassis closed at the front and rear with a plug-in plate -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - aluminium 15%)

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually Csdstx Nwnopfx Aaxjrb * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: new, empty load weight: 11,000 kg, maximum load weight: 27,000 kg, overall weight: 38,000 kg, axle configuration: 2 axles, loading space length: 7,300 mm, loading space width: 2,550 mm, tire size: 235/75 R17.5, color: grey, operation weight: 11,000 kg, Equipment: ABS, Chassis: -Steel frame welded construction with front and rear frame offset and low bed without rear bevel -Frame neck + fifth wheel plate 225 mm -Low bed designed for point load 25 tonnes over 5 m -Outer frame closed on the outside with welded-in tie rings for lashing -Replaceable 2" king pin -Rear suspension rail for aluminium ramps Axles and tyres: -BPW low-loader axles, 10 tonnes axle load each, bellows diameter 360 mm -Air suspension with lifting and lowering device, stroke 220 mm (-60/+160 mm) -Wabco SmartBoard with ECAS function for 2 coupling heights + 100 mm -S-cam brake 300/200 mm, asbestos-free brake pads -Automatic slack adjuster -IVTM tyre pressure monitoring -9 tyres 235/75 R 17.5, tubeless Steering: -1. and 2nd axle hydraulically forced-steered via fifth wheel coupling Floor: -Multi-layer glued plate floor with a thickness of 27 mm flush with the outer frame and longitudinal beams -Reinforced at the bottom with GRP coating -12 pairs of binding rings welded into the outer frame (8 pairs of RUD 8 ton - 6 pairs in the low bed and one pair each on the gooseneck and at the beginning of the rear unit - 2 pairs of 4 ton lashing rings each on the gooseneck and rear unit) Crjdpfx Ajiu Eu Nsaxsb -6 pairs of mushrooms in the outer frame in the low bed -Storage compartment with lid in the floor of the low bed at the front left and right Front wall: -25 mm aluminum hollow profiles raised up to the lower edge of the roof with integrated tarpaulin tensioning device Sliding tarpaulins: -Sliding tarpaulins on both sides with welded vertical and horizontal straps (distance approx. 600 mm) and tension fasteners made of stainless steel -Adjustable tarpaulin straps (over dead center) up to loading width of 4,000 mm including tarpaulin extension with press studs and Velcro fastener -Tarpaulin extension in direction of travel: 300 mm, height: 750 mm -Incl. Eyelets for loose tarpaulin extension part -1 pair of vertical tarpaulin pockets with a length of approx. 1,000 mm, position in the low bed at the front bend -With belt pockets Rear wall: -Steel rear portal frame with side tarpaulin attachment device -Aluminium double-wing door, 25 mm thick -Both door wings can be fully folded over with door stop -One aluminium double-joint hinge and two recessed grip recesses per door wing Corner pillars at the front: -At roof height, screwed on to the front Central pillars: -3 pairs of continuously adjustable folding pillars -The pillars can be moved along the entire length using a trolley -Central pillars in the low bed can also be fixed in the rear platform Roof: -EDSCHA sliding roof (galvanised) with crossbars that can be moved in both directions (pushed together towards the front in the loading space) -Rear portal crossbeam can be swung away -PVC tarpaulin roof without customs seal -Hand hydraulic lifting roof on both sides, lifting 450 mm -Lifting roof can be moved in the positions at the front (9x50) and rear (9x50) -Including tarpaulin extension and tarpaulin flap at the rear -Canopy at the very front of the bulkhead can be cranked out 900 mm each Accessories: -Extendable warning signs (removable at the front and rear with socket) including position lights up to a loading width of 4,000 mm -Storage of the 4 warning signs on the inside of the front wall, top right and left -1 aluminum ladder with bracket 2,500 mm long on the front wall -2 rows of aluminum slats attached in a self-locking manner -Sheet metal mudguard with mud flaps -1 night parking sign and 1 ADR

Condition: used, mileage: 129,252 km, lifting height: 38,000 mm, Year of construction: 2015, Drive: Wheel Unladen weight: 27,875 kg Csdpfsw A Hb Tjx Aaxjrb Lifting capacity: 23,800 kg Serial number: 122024 Front tyre condition: 70 Rear tyre condition: 70 Transport dimensions (L x W x H): 11.1 x 2.55 x 3.9 Please contact PFEIFER GROUP for further information.

Condition: new, empty load weight: 15,550 kg, maximum load weight: 47,450 kg, overall weight: 63,000 kg, axle configuration: 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm -Rear gooseneck with bevel approx. 1,000 mm x 10° Loading area: -Loading area in extendable design, length approx. 8,800 mm, with bevel at the rear approx. 500 mm x 10° -One recess protruding into the loading surface and into the chamfer to accommodate the excavator dipper arm -Pneumatic locking with conical locking pins and reinforced locking positions -Hardwood covering on the bevel of the loading area Ramps: -1 Pair of two-part steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm -Ramps with hardwood decking -Hydraulically folding ramp tips -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards -Square climbing ledges 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and suspension: -BPW axles and suspension, 1st axle with preload steering, all other axles with forced hydromechanical steering -Technical axle load: 12,000 kg -1st axle with electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -235/75 R 17.5 twin tires -TPMS tire monitoring system in accordance with ECE R141 -TPMS tire monitoring sensors mounted in all wheels including spare wheels Accessories included: -steel front wall, pluggable, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Parking position on the gooseneck for the warning signs when not in use -1 Spare wheel -On the gooseneck 1 pair of plug-in ALU side panels, approx. 400 mm high, anodized -One plug-in ALU rear panel on the gooseneck, approx. 400 mm high, anodized -Approx. 40 mm thick hardwood covering over the gooseneck, checker plate covering over the kingpin -2" kingpin Csdok Aht Uopfx Aaxerb -Guide plate from the gooseneck for the saddle plate, approx. 500 mm wide -4 wheel chocks -Mechanical seat posts with 2-speed gearbox and crank -JOST module B - static test load = 50,000 kg -1 Intermediate table, approx. 300 mm wide -Widenings (galvanized) extendable by approx. 230 mm per side -Wheel recesses with square climbing rails -ALU covers for the wheel recesses -1 pair of mechanical rear supports -Steering can be operated from the front and rear by cable remote control, with tracking control of the axles -1st axle with automatic lift axle function -Central lubrication system with 1 pump, BEKAMAX brand -Radio remote control for operating the self-steering, in addition to the cable remote control, with 2 indicator lights on the receiver as toe-in control -Wabco Smart Board System -4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for rotating beacon

Condition: used, mileage: 70,275 km, power: 390 kW (530.25 HP), first registration: 06/2021, fuel type: diesel, axle configuration: 8x8, wheelbase: 4,800 mm, fuel: diesel, brakes: engine braking, color: white, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, suspension: steel, loading space length: 5,950 mm, loading space width: 2,470 mm, loading space height: 1,460 mm, Year of construction: 2021, Equipment: ABS, AdBlue, air conditioning, central locking, crane, cruise control, differential lock, electric window regulation, parking heater, seat heater, traction control, trailer coupling, = Additional Options and Accessories = - Remote central locking - Pintle hook - Hub reduction - PTO (Power Take-Off) - Radio Crjdpfxex S N Hkj Aaxsb - Reversing camera - Sun visor - Auxiliary heater - Toolbox = Notes = Mercedes-Benz Arocs 3253 8x8 Full spring suspension. 2 sets of tyres. Road: 385/65R22.5 315/80R22.5 Off-road: 14.00R20 Copma 650.6 Jib with 6 extensions. Winch. Front outriggers. Scanreco radio remote control. Personnel basket. Lifting capacities: 2.00 m - 27,520 kg 4.30 m - 12,800 kg 5.95 m - 9,070 kg 7.70 m - 6,840 kg 9.55 m - 5,380 kg 11.40 m - 4,420 kg 13.50 m - 3,680 kg 15.60 m - 3,160 kg 2 x manual extension 18.71 m - 1,720 kg 20.11 m - 1,520 kg 21.75 m - 1,240 kg 23.46 m - 1,000 kg 25.19 m - 870 kg 26.96 m - 800 kg 28.76 m - 720 kg 80 cm hydraulic extension on loading platform. = Further Information = Technical Information Number of cylinders: 6 Axle Configuration Brakes: Drum brakes Suspension: Leaf suspension Front axle 1: Steering Front axle 2: Steering Weights Empty weight: 24,855 kg Payload: 12,145 kg Gross vehicle weight: 37,000 kg Functionality Crane: Copma Financial Information Price: On request Identification Type number: AROCS 3253 8x8 / 65 t/m CRANE + = Company Information = ALL PRICES ARE NET FOR EXPORT. Joris Versteijnen (NL-DE-EN), Wouter Greutink (NL-DE-EN-ES-IT), Govorim po russki. We strive to provide accurate information, however, no rights can be derived from the posted texts.

Condition: used, mileage: 278,066 km, Year of construction: 2009, Drive: Wheel Unladen weight: 72,000 kg Lifting capacity: 150,000 kg Serial number: 068506 Front tire condition: 80% Rear tire condition: 80% Transport dimensions (L x W x H): 16.2 x 2.85 x 3.95 m Please contact PFEIFER GROUP for further information. Crjdjw D N Raepfx Aaxsb

Condition: excellent (used), axle configuration: > 3 axles, first registration: 08/1994, color: yellow, Year of construction: 1994, Equipment: ABS, = Further options and accessories = - Air suspension = Additional information = Axle configuration Rear axle 1: Twin tires Rear axle 2: Twin tires Rear axle 3: Twin tires; Steering Rear axle 4: Twin tires; Steering Weights Unladen weight: 11,420 kg Functional Loading platform height: 77 cm Extendable body: Yes Condition Technical condition: Very good Optical condition: Very good Financial information Price: On request NOOTEBOOM OSD-50-04-V SEMI LOW LOADER 4x SAF axles 2x steering axles (trailing) Air suspension Tyre size 205/65/R17.5 Extendable loading platform Length 923 cm + 670 cm extendable, total loading platform length 1593 cm Width of loading platform 275 cm + 2 x 27.5 cm side extension, total platform width 330 cm Height of loading platform approx. 77 cm when loaded Gooseneck length 388 cm Lashing eyes and stake pockets 2x rear supports FOLLOW US ON INSTAGRAM: GEURTSTRUCKS WE SPEAK GERMAN HABLAMOS ESPANOL Crjdpfx Asuxy Dfsaxjb WE SPEAK ENGLISH

Condition: used, mileage: 53,318 km, lifting height: 110,000 mm, Year of construction: 2018, Drive: Wheel Unladen weight: 60,000 kg Lifting capacity: 250,000 kg Serial number: 088666 Front tire condition: 90% Rear tire condition: 90% Credpfxowz Utzs Aaxeb Transport dimensions (L x W x H): 15.86 x 2.99 x 3.99 m Contact PFEIFER GROUP for further information.