Semi low-loader

Lako | SPECIAL TRAILER | PALFINGER 42502 | FULL STEE...

Condition: new, empty load weight: 17,500 kg, maximum load weight: 43,500 kg, overall weight: 61,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,750 mm, loading space height: 400 mm, tire size: 245/70 R 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and lowered hydraulically -For tractor units: 6x4 or 8x4 Drop deck: -Low bed with external beams in extendable design, "SUPER LOW" design, length approx. 7,550 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking mechanism The supply lines are protected in the pull-out supports and automatically adjust to the respective drop-down bed length Rear chassis: -Rear chassis with closed outer frame, checker plate covering and continuous Prisma excavator trough approx. 1,450/900 x 505 mm, open at the rear -2 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame Axles and tires: -"PENDEL-AXLE", all axles with hydromechanical forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with stopcocks and locking pin for securing in raised position -Technical axle load: 12,000 kg Hnodpeh Hm Thefx Aaask -Hydraulic axle compensation -245/70 R 17.5 / 3PMSF tires Accessories included: -Preparation for mounting bolt-on container positioners for 1x 20ft or 1x 40ft container on the outer beams -2" kingpin -One galvanized steel end wall approx. 400 mm high -One spare wheel with holder -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering can be operated from the front and rear by remote control cable via pushbuttons, with axle tracking control -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw coupling -Electric hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and red at the rear -2 wooden blocks 500x250x200 mm -European reflector plates (red/yellow) at the rear of the trailer -On the gooseneck and on the rear plate on the left and right, one holder each for the warning signs including socket -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 standard grease -Load manometer for determining the axle loads including load diagram -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,000 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,120 mm) -Separate air connection with air gun on the gooseneck -Duomatic air coupling from gooseneck to low bed -Gooseneck closed in the rear upper area with a removable cover -1 pair of steel ramps for bridging the mounting hooks of the low bed -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm -Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control 6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD rings VLBG-4 -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -folding extensions, approx. 230 mm on each side -A layer of sand painted onto the loading surface to prevent slipping Dipper arm recess of the rear chassis closed at the front and rear with a plug-in plate -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - aluminium 15%)

Condition: used, mileage: 360,000 km, power: 390 kW (530.25 HP), first registration: 05/2020, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, brakes: retarder, color: blue, gearing type: automatic, emission class: euro6, Year of construction: 2020, Equipment: ABS, air conditioning, crane, electronic stability program (ESP), navigation system, parking heater, DAF XF 530 6X2 lift/steer, fully air-suspended flatbed with crane absolutely fully equipped Wheelbase: 4800mm Loading area: 6200mm Overall length: 9900mm Crane: Palfinger PK 23002-SH, continuous rotation, 6+1 extensions, total 19m, 740kg, radio remote control, hose package with quick couplers, pallet fork (1100 hours) Condition: Top and fully equipped Hjdpfxsx Sbz Te Aaaonk Trailer also currently available – two variants: Jumbo or Standard

Condition: used, mileage: 403,500 km, power: 360 kW (489.46 HP), first registration: 10/2017, fuel type: diesel, tire size: 385/55R22.5, axle configuration: 8x2, wheelbase: 3,750 mm, fuel: diesel, brakes: retarder, color: blue, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, suspension: air, total length: 10,450 mm, total width: 2,550 mm, loading space length: 6,350 mm, loading space width: 2,540 mm, loading space height: 1,100 mm, Year of construction: 2017, Equipment: ABS, AdBlue, air conditioning, crane, cruise control, differential lock, lane keeping assist, parking heater, retarder, seat heater, traction control, trailer coupling, = Additional options and equipment = - Alarm system - Refrigerator - Lift axle - Air suspension - Towing jaw coupling - Engine brake - PTO (Power Take-Off) - Reversing camera - Disc brakes - Sun visor - Spotlights - Lane departure warning system - Auxiliary heater - Toolbox = Notes = Hnsdpjx Srx Nofx Aaask HMF 5020 K6 FJ 1000 Front stabilizer. Scanreco radio remote control. 4.70 m - 9,270 kg 6.40 m - 6,460 kg 8.30 m - 4,780 kg 10.30 m - 3,700 kg 12.30 m - 3,000 kg 14.40 m - 2,500 kg 16.70 m - 2,150 kg FJ1000 19.70 m - 1,100 kg 21.30 m - 990 kg 22.90 m - 900 kg 24.70 m - 820 kg 26.60 m - 700 kg 28.50 m - 575 kg Hydraulic rear bumper and table. 2 x hydraulic outrigger supports. Loading platform 635 cm + 120 cm extension. 110 cm loading height. = Further Information = Technical Information Number of cylinders: 6 Axle configuration Brakes: Disc brakes Suspension: Air suspension Front axle: Tire size: 385/55R22.5; Steering axle; Tire tread left: 70%; Tire tread right: 70% Rear axle 1: Tire size: 305/70R22.5; Twin tires; Tire tread left inside: 45%; Tire tread left outside: 45%; Tire tread right inside: 45%; Tire tread right outside: 45% Rear axle 2: Tire size: 305/70R22.5; Twin tires; Tire tread left inside: 45%; Tire tread left outside: 45%; Tire tread right inside: 45%; Tire tread right outside: 45% Rear axle 3: Tire size: 385/55R22.5; Steering axle; Tire tread left: 50%; Tire tread right: 50% Weights Curb weight: 22,285 kg Payload: 14,715 kg Gross vehicle weight: 37,000 kg Functionality Crane: HMF Financial Information Price: On request Identification Type number: G490 8x4*4 / HMF 5020 + JIB = Company Information = ALL PRICES ARE NET FOR EXPORT. Joris Versteijnen (NL-DE-EN) Wouter Greutink (NL-DE-EN-ES-IT) We speak Russian as well. We strive to provide accurate information, however, no rights can be derived from the information shown.

Condition: new, functionality: fully functional, BERTOJA SEMITRAILER 13.80m Hedpfexpi A Rex Aaasnk NEW, READY FOR REGISTRATION Double galvanized hydraulic ramp Edge rail on neck Winch preparation Self-steering axle CONTACTS: 0823 1686306 335 6713062 OPENING HOURS: MONDAY-FRIDAY 8:30 AM - 7:00 PM / SATURDAY 8:30 AM - 2:00 PM WE OFFER A LARGE SELECTION OF USED MULTI-BRAND COMMERCIAL AND INDUSTRIAL VEHICLES: Fiat – Hyundai – Daf - Mercedes Benz – Renault – Peugeot – Iveco – Mitsubishi – Scania - S-Way -S500-V8-650-580-730-S500-S 500-S500 – Stralis – Man - Nissan V8 - Intarder- 770s -Limited Edition - 660 S Semitrailer-Refrigerated Semitrailer Tipper – Lamberet - Schmitz Isuzu-Fixed body-Crane-Tipper- 4 axles -4 Rear Axles -Tway-T-Way-540- 460 hp - Xway-X-Way-Trilateral - V8 - Scania - Frost Edition Curtain Sider-Box body-Liftgate - Refrigerated Cell- Insulated with Fridge - Van Domenico Truck srl declines any responsibility for any discrepancies in technical specifications, options, and features, which may in some cases differ from those described. We invite you to verify the specifications of the specific vehicle.

Condition: excellent (used), mileage: 242,362 km, power: 360 kW (489.46 HP), first registration: 09/2016, fuel type: diesel, tire size: 385/22/22.5, axle configuration: 8x2, fuel: diesel, brakes: engine braking, color: white, driver cabin: sleeper cab, gearing type: automatic, number of gears: 12, emission class: euro6, suspension: air, permissible axle load (axle 1): 9,000 kg, permissible axle load (axle 2): 9,000 kg, permissible axle load (axle 3): 12,700 kg, loading space length: 6,250 mm, loading space width: 2,500 mm, loading space height: 1,100 mm, Year of construction: 2016, Equipment: ABS, AdBlue, air conditioning, central locking, crane, cruise control, differential lock, electric window regulation, fog lights, navigation system, parking heater, power mirror, soot filter, trailer coupling, = Additional Options and Accessories = - Aluminum fuel tank - Brake booster - High beam headlights - Speed limiter - Refrigerator - Alloy wheels - Air suspension - Particulate filter - Reversing camera - Sun visor - Auxiliary heater - Toolbox - Power take-off (PTO) - Central lubrication system - Towing eye = Further Information = Axle configuration Brakes: Disc brakes Suspension: Air suspension Front axle 1: Tire size: 385/22/22.5; Alloy wheels; Max. axle load: 9,000 kg; Steered Front axle 2: Tire size: 385/55/22.5; Alloy wheels; Max. axle load: 9,000 kg; Steered Rear axle 1: Tire size: 315/60/22.5; Twin tires; Differential lock; Alloy wheels; Max. axle load: 12,700 kg Rear axle 2: Tire size: 315/60/22.5; Alloy wheels; Lift axle; Max. axle load: 8,300 kg Weights Unladen weight: 25,800 kg Payload: 10,198 kg Gross vehicle weight: 36,000 kg Functional Mast: Telescopic (14 sections) Mast length: 38 m Lifting capacity: 26,200 kg Lifting height: 3,800 cm Crane: EFFER 955/8S + JIB 6S, year of manufacture 2016, mounted behind the cab Superstructure brand: EFFER 955/8S + JIB 6S CE mark: yes Condition Technical condition: very good Visual condition: very good SCANIA G490 LB8X2*6HNB WITH EFFER 955/8S + JIB 6S CRANE + WINCH EURO 6 | PACKAGE 490 HP DRIVE 8X2*6HNB LAST AXLE LIFT AND STEERABLE!!! FULL AIR SUSPENSION WHEELBASE 610 CM CG19H SLEEPER CAB FULL OPTIONS WITH AIR CONDITIONING, AUXILIARY HEATER, NAVI, CAMERA, REFRIGERATOR, LEATHER, TV SPECIAL INTERIOR WITH LED LIGHTING OPTICRUISE AUTOMATIC GEARBOX TRAILER COUPLING NUMEROUS TOOLBOXES!!! ALCOA RIMS OPEN LOADING PLATFORM LOADING PLATFORM LENGTH 625 CM + 300 CM HYDRAULICALLY EXTENDABLE, TOTAL LENGTH 925 CM LOADING PLATFORM WIDTH 255 CM + SIDE EXTENSIONS HOOK EYES + STANCHION POTS + TWISTLOCKS Hnsdpfx Ajyiuqnsaajk EFFER 955/8S + JIB 6S + WINCH OIL COOLER FOR CRANE HYDRAULICS 14X HYDRAULICALLY EXTENDABLE TOTAL WORKING HEIGHT 38 METERS!! MAX. LIFTING CAPACITY AT 2.50 M = 26,200 KG MAX. LIFTING CAPACITY AT 33.55 METERS = 720 KG CRANE CAN OPERATE IN FRONT OF THE CAB USING 1X FRONT OUTRIGGER 100% EXTRA CHASSIS REINFORCEMENT TOTAL OF 5 OUTRIGGERS LARGE HYDRAULIC WINCH WITH ATTACHMENT HOOKS AND ROLLERS RADIO REMOTE CONTROL

Condition: new, empty load weight: 10,700 kg, maximum load weight: 38,800 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r 17,5, color: grey-black, Equipment: ABS, Gooseneck: •Gooseneck with bevelled corners at the front 45° and with a rear bevel of approx. 750 mm x 10° •3 pairs of lashing rings •Hardwood flooring 30 mm thick Hnsdohlz S Nspfx Aaajk Loading area in extendable version: •Loading area in extendable version with rear bevel of approx. 1,000 mm x 8° •Cutouts in the outer frame of the loading area for hanging tensioning straps •Hardwood flooring approx. 48 mm thick, checkered sheet covering over the axles Two-part steel ramps: •One pair of galvanised, two-part steel ramps with approx. 48 mm thick hardwood flooring •Ramp with hydraulically foldable and unfoldable ramp parts, hydraulic lifting mechanism and hydraulically movable •Maximum load per pair: approx. 40,000 kg Axles and Tires: •BPW axles and suspension, 2 axles rigid, 1 axle with self-steering •Technical axle load: 12,000 kg •Electro-magnetic reversing lock can be activated via reverse gear and manually •Air suspension with lifting and lowering valve •Axle tool •235/75 R 17.5 3PMSF Brake system: •WABCO brake system in accordance with EU regulations with EBS-E Paintwork: •First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component zinc dust primer •A high-quality 2-component top coat in one color in MB 7350 Nova gray •Rear section metallized and painted in RAL 9010 Seatposts: •JOST seatposts with 2-speed gearbox for 24t lifting load (50t test load). Steel construction: •Steel construction made of high-strength fine-grain steel •Steel qualities: •S355J2+N/S355MC •S690QL/S700MC Electrical system: •Electrical system in accordance with EU regulations, 24 volt lighting •ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets Accessories included: •A spare wheel with holder •A galvanized steel bulkhead approx. 400 mm high •Yellow-red air couplings on the galvanized front connection panel •4 wheel chocks •A bracket for a rotating beacon at the rear of the trailer •Mounting in the rear area of the gooseneck for aluminum docking ramps •Galvanized folding supports under the bevel of the loading area •Cover plates to bridge the space between the ramps and the loading area •White Reflective tape in accordance with EU regulations on the side, on the extension and at the rear, red •Electro-hydraulic unit at the rear, under the loading area •A holder for the warning signs including a socket on the gooseneck and on the ramps on the left and right •Control valves for the ramps attached to the right-hand side of the trailer •ALU side walls and rear wall on the gooseneck, approx. 2,440 x 400 mm •The rear, galvanized plug-in stanchions are removable (length of the structure approx. 2,560 mm) •Four warning signs extendable by approx. 400 mm with a position light •3 pairs of WADER container pockets in the loading area for a 20ft, 30ft or 40ft container •6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading area •Galvanized extensions, extendable by approx. 230 mm each Page •Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area bevel •A painted layer of sand on the checker plates, above the kingpin and the loading area as anti-slip protection •Load pressure gauge for determining the axle loads including load diagram •HRM metallization (High Resistance Metallization) of the outer frame •Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: new, empty load weight: 10,350 kg, maximum load weight: 39,150 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area: -telescopic loading area with rear slope approx. 1,000 mm x 8° -1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm -Wheel recesses with square climbing strips 15 x 15 mm and widenings in the lower area -A pair of fixed wheel recesses between the 1st and 2nd axles, approx. 1,610 x 970 x 400 mm -3-piece removable galvanized covers over the wheel recesses (W 670 mm) - max. point load 5 to / pc. -Recess in the chamfer and protruding into the loading area to accommodate the excavator dipper stick approx. 2,900 x 750 x 210/290 mm -1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) -5 pairs of lashing rings foldable outwards (LC 5,000 daN) -2 pairs of lashing rings can be folded outwards (LC 10,000 daN) -2 pairs of lashing rings in the excavator trough (LC 5,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) One-piece ALU ramps: -One pair of one-piece ALU ramps approx. 2,500 x 600 mm -Ramp with spring lifting mechanism and manually adjustable -Maximum load per pair: 24,000 kg Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 tires -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories included: -One spare wheel with holder in front of the bulkhead Hnsdpeiu Er Aefx Aaaek -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking lights -Galvanized extensions, extendable by approx. 230 mm per side -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon at the rear of the trailer -White reflector tape in accordance with EU regulations on the sides, on the pull-out and red at the rear -One bracket for the warning signs including socket on the left and right of the gooseneck and on the rear panel -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container -3 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -One removable galvanized intermediate table with 1 pair of WADER container pockets -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -a layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -A bracket for a rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: used, axle configuration: > 3 axles, first registration: 10/2006, total width: 2,850 mm, suspension: other, tire size: 285/70R19.5, color: black, Year of construction: 2006, Equipment: ABS, = Additional options and accessories = - Central lubrication system = Remarks = Faymonville Jeep Dolly D3 Year 10/2006. 1 x lift axle. 1 x friction-steered axle (trailing steering axle). Air suspension. Max. technical weight: 56,000 kg. Faymonville STBZ-5VA Year 10/2006. Pendle axle. Detachable gooseneck. Movable deck. Extendable bed: 400 cm. Hjdpfx Aexbng Eoaasnk Load bed: 650 + 400 cm. 50,000 kg neck load capacity. Max. technical weight: 119,680 kg. = Further information = Axle configuration Tire size: 285/70R19.5 Brakes: drum brakes Front axle 1: twin tires; left inner tread: 15%; left outer tread: 60%; right inner tread: 60%; right outer tread: 60%; suspension: air suspension Front axle 2: twin tires; left inner tread: 30%; left outer tread: 30%; right inner tread: 40%; right outer tread: 60%; suspension: air suspension Front axle 3: twin tires; steered; left inner tread: 30%; left outer tread: 70%; right inner tread: 60%; right outer tread: 70%; suspension: air suspension Rear axle 1: twin tires; steered; left inner tread: 30%; left outer tread: 60%; right inner tread: 40%; right outer tread: 70%; suspension: hydraulic suspension Rear axle 2: twin tires; steered; left inner tread: 50%; left outer tread: 50%; right inner tread: 30%; right outer tread: 75%; suspension: hydraulic suspension Rear axle 3: twin tires; steered; left inner tread: 60%; left outer tread: 60%; right inner tread: 60%; right outer tread: 60%; suspension: hydraulic suspension Rear axle 4: twin tires; steered; left inner tread: 60%; left outer tread: 60%; right inner tread: 40%; right outer tread: 50%; suspension: hydraulic suspension Rear axle 5: twin tires; steered; left inner tread: 70%; left outer tread: 70%; right inner tread: 20%; right outer tread: 70%; suspension: hydraulic suspension Weights Unladen weight: 36,600 kg Payload: 83,080 kg Gross vehicle weight: 119,680 kg Financial Information Price: On request Identification Type number: STBZ-5VA + 3 AXLE JEEP DOLLY / E = Company information = ALL PRICES ARE NET FOR EXPORT. Joris Versteijnen (NL-DE-GB) Wouter Greutink (NL-DE-GB-ES-IT) We speak Russian. We make every effort to provide correct information, but no rights can be derived from the listed texts.

Condition: good (used), axle configuration: 3 axles, loading space length: 18,520 mm, loading space width: 2,750 mm, loading space height: 450 mm, total length: 18,520 mm, total width: 2,750 mm, total height: 450 mm, suspension: hydraulics, tire size: 245 / 70 R17.5 | Load index 146/146F, color: white, Year of construction: 2014, = Further Information = General Information Year of manufacture: 2014 Axle Configuration Tyre size: 245 / 70 R17.5 | Load index 146/146F Axle make: BPW Hydraulic pendulum axles Suspension: hydraulic suspension Rear axle 1: Twin tyres; Max. axle load: 12,000 kg; Steering Rear axle 2: Twin tyres; Max. axle load: 12,000 kg; Steering Rear axle 3: Twin tyres; Max. axle load: 12,000 kg; Steering Weights Unladen weight: 17,200 kg Payload: 53,800 kg Gross vehicle weight (GVW): 71,000 kg Functional Extendable superstructure: Yes Hodpfxexyh I Tj Aaaenk Condition Technical condition: Good Visual condition: Good Financial Information Price: On request Additional Information Please contact Stefan Schaapveld for further information.

Condition: new, maximum load weight: 30,190 kg, overall weight: 43,000 kg, axle configuration: 2 axles, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the equipment list. Full equipment details available on request. Loading Platform: - Lowbed with external beams in extendable SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking mechanism - Supply lines protected inside the extendable side rails, automatically adjusting to the current bed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for attaching RUD screw-on rings Gooseneck: - Gooseneck in SNT design for optimized platform length, length approx. 3,750 mm - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractors: 4x2, 6x2 Rear Chassis: - Rear chassis in short version with closed external frame and checker plate cover - Running gear with excavator recess, closed in the rear half to accommodate the air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings horizontal, front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Technical axle load per axle: 12,000 kg - Air suspension with lift and lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF - Manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transmission to the truck via the standardized EBS interface in accordance with ISO 11992 - The truck must be capable of processing and displaying this data for correct operation Braking System: - Braking system according to EU regulations with EBS-E (2S2M) Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with indicators - ASPÖCK-UNIBOX at the front connection point with 24N, 24S, and 15-pin sockets as per standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel Construction: - Steel construction from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure is automatically shot-blasted after welding using a blasting turbine system - Second blasting process with corundum for optimal adhesion of coating system - HRM metallization of complete chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection Hodpfxsxarl Ne Aaaenk - Final paint finish with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, as per RAL system 841GL - Rims in silver - Rear section metallized and painted RAL 9010 (Pure White) - Metallic paint not possible - Paint system tested in salt spray test as per ISO 9227-NSS - Cavities sealed with special wax Including the following additional equipment: - 2" King pin - One galvanized steel front wall, approx. 400 mm high - Remote steering of front and rear axles by cable remote control with pushbuttons, including single track axle monitoring (without installation in the tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Electro-hydraulic power pack - Preparation for mounting container locks for 1x 20' or 1x 40' container on the external beams - Without container locks