Used Humbaur Horse Trailers for sale (661)

Condition: new, overall weight: 10,500 kg, maximum load weight: 8,200 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,010 mm, loading space height: 350 mm, Year of construction: 2024, Equipment: ABS, * Drum brakes * Ramps spring-supported & can be moved sideways * Frame completely hot-dip galvanized * 16 lashing eyes on the loading area Cgebvpvjh Rlx Dscijt * Loading height approx. 700 mm * Height-adjustable tow arm * Trailer available immediately * Technically permissible total weight 11,900 kg with payload 9,450 kg * Suspension: leaf * Payload: 8,200 kg * Tires: 235/75R17.5 ----Information non-binding - errors not excluded - sale reserved

Condition: new, overall weight: 18,000 kg, maximum load weight: 14,510 kg, axle configuration: 2 axles, loading space length: 7,100 mm, loading space width: 2,485 mm, loading space height: 1,000 mm, suspension: air-lift, tire size: 385/65 r22,5, Equipment: ABS, center pivot plate, tail-lift, trailer coupling, HUMBAUR 18.0 to building material trailer with platform length 7,100 mm, Typ. HD 18.0 building material (PLUS) --- --- INCLUSIVE hot-dip galvanized chassis & bogie INCLUSIVE aluminium dropside superstructure, anodized INCLUSIVE galvanized Kinnegrip stanchions with dropside partition, transverse at the rear INCLUSIVE gas pressure lifters integrated in the side walls Cgsbjkn N Rtsvpvciet INCLUSIVE SAF air suspension disc brake Equipment: * Permissible total weight 18,000 kg * Payload approx. 14,510 kg * Welded chassis frame with stretched cross members in lightweight construction * Loading area approx. 7,100 x 2,480 mm * Unloaded loading height approx. 1,285 mm * Overall dimensions: LxWxH approx. 8,900 x 2,550 x 2,485 mm (B dimension 8,850 mm) * ALU drop sides 1,000 mm high, anodized, can be folded down at the sides and rear, galvanized Kinnegrip stanchions, transverse at the rear * ALU front wall 1,200 mm high, anodized * Folding steps on the inside of the rear wall * Gas pressure lifters integrated in the side walls * 9-ton SAF Intradisc disc brakes 430mm * SAF air suspension with 385/65R22.5" tires * Drawbar 2,000 mm long, height-adjustable for coupling heights of approx. 700 - 900 mm * 40 mm DIN towing eye * Perforated outer frame, hole spacing 125 mm, 57 pairs of lashing holes, 2000 daN each * 2-circuit air brake system * EBS braking system 24 Volt * Spring-loaded parking brake * Hot-dip galvanized chassis & bogie * Mudguards with spray protection mats * Electrical system: 15-pin 24 Volt * Brake connection: 2 interchangeable coupling heads red/yellow ISO 1728 Your advantages: * High-quality and corrosion-protected anodized aluminium side wall construction * Optimum corrosion protection thanks to hot-dip galvanizing in an immersion bath * Simple and easy handling of the drop sides thanks to the gas pressure lifters * Ideal load securing options thanks to standard lashing options * Height-adjustable towing fork enables compatibility with the different coupling heights of towing vehicles * Low tare weight => therefore high payload ∗Stock vehicle - promptly available ∗Subsequent sale reserved ∗Price ex works

Condition: used, overall weight: 2,500 kg, maximum load weight: 1,864 kg, axle configuration: 2 axles, loading space length: 3,050 mm, loading space width: 1,500 mm, loading space height: 1,800 mm, first registration: 07/2020, total width: 2,026 mm, 1450. GW210947474 Box trailer from Humbaur Wing doors, lockable Wooden floor Double axle Color: white 100 km/h approval ... and much more ---- Cgsbvpohmmtqevcijt The vehicle is unprepared! Nationwide delivery possible for an additional charge. Subject to errors and prior sale. We are happy to accept your vehicle as part payment. Financing / leasing also possible without a down payment! Do you have any questions? We are happy to advise you!

Condition: new, overall weight: 1,800 kg, maximum load weight: 1,145 kg, axle configuration: 1 axle, loading space length: 3,100 mm, loading space width: 1,765 mm, loading space height: 1,800 mm, Year of construction: 2024, total width: 2,456 mm, total height: 2,378 mm, !!! SPECIAL OFFER !!! only one item in stock Other technical data: Permissible total weight 1,800 Axles 1 Payload 1,145 Loading space length 3,100 Loading space width 1,765 Loading space height 1,800 Description: This box trailer is characterized by an intelligent lowering mechanism that makes loading and unloading particularly convenient. With an extremely flat ramp angle of only 4 to 6 degrees as well as an integrated ramp and upward-opening tailgate, it offers optimal conditions for smooth loading. The robust, non-slip floor and the durable side walls with GRP coating ensure maximum stability. In combination with an optional rocker, the trailer is also ideal for the safe transport of motorcycles. Standard equipment: Bolted, hot-dip galvanized chassis * Loading area can be lowered hydraulically with a hand pump * Mechanical safety lock of the swivel axle when driving * Humbaur multifunctional lighting * Wooden floor 15 mm thick * 4 pairs of integrated lashing rings (tractive force 400 kg per lashing ring, Dekra tested) * Side walls and roof made of 14 mm thick multi-layer wood with GRP coating * Interior light installed * Tailgate opens upwards * Internal ramp * Espagnolette lock and hinges galvanized Images do not always correspond to the basic equipment and sometimes contain accessories that are subject to an additional charge. Errors and changes reserved. NEW PRODUCT - Incl. invoice with VAT, braked 2 years TÜV/unbraked 3 years TÜV and 2 years guarantee. The vehicle registration document can be sent in advance after the deposit or payment has been made so that you can register the trailer for collection. Collection from the main office Engelhard trailer wholesale market Steinauer Weg 15 91589 Aurach Tel: Fax: 9 Homepage: If desired, the handover can also take place in 06618 Wethau, (Gmach company) collection warehouse OST near Leipzig Tel. , Fax for an additional charge of 250.00 euros (if in stock there!). The handover fee is to be paid directly on site Cjbvpvjux T A Usciegt IMPORTANT! - If you would like to be collected in Wethau, please call beforehand to inquire about availability! Opening times: Monday - Friday 8.00 a.m. - 12.00 p.m. and .00 a.m. - 5.00 p.m. Saturday 9.00 a.m. - .00 p.m. Outside of these times, you can also send your inquiries at any time by fax 9.

Condition: new, overall weight: 10,500 kg, maximum load weight: 7,700 kg, axle configuration: 2 axles, loading space length: 6,200 mm, loading space width: 2,460 mm, loading space height: 400 mm, Year of construction: 2024, Equipment: ABS, * Drum brakes * Ramps spring-supported & can be moved sideways Cebvpoq A A Nzovcijgt * Frame completely hot-dip galvanized * 20 lashing eyes on the loading area * Loading height approx. 920 mm * Height-adjustable tow arm * Trailer available immediately * Technically permissible total weight: 11,900 kg with payload 9,100 kg * Suspension: leaf * Payload: 7,700 kg * Tires: 235/75R17.5 ----Information non-binding - errors not excluded - sale reserved

Condition: new, overall weight: 19,000 kg, maximum load weight: 14,600 kg, axle configuration: 2 axles, loading space length: 5,010 mm, loading space width: 2,420 mm, loading space height: 900 mm, suspension: air/air, tire size: 385/65 r22,5, Equipment: ABS, tail-lift, trailer coupling, HUMBAUR 19.0 to tandem three-way tipper with Hardox body, Typ. HTK 195024 Gravel tipper PLUS --- INCLUDING HARDOX side walls, rear wall and rear floor, 900 mm high INCLUDING HOT-DIP GALVANIZED CHASSIS & DRAWBAR INCLUDES tipper body and superstructure KTL and powder-coated in color of choice INCLUSIVE with automatic tailgate release INCLUSIVE SAF air suspension and drum brake INCLUSIVE dropside jack in FR left Equipment: * Permissible gross weight 19,000 kg * Payload approx. 14,600 kg * Loading area approx. 5,010 x 2,420 mm * Unloaded loading height approx. 1520 mm * Overall dimensions: LxWxH approx. 7,150 x 2,550 x 2,550 mm * Bridge floor made of 4 mm highly wear-resistant steel, HB 450; * HARDOX superstructure 900x3 mm, swinging side walls with central locking system * Left-hand side wall spring jack in direction of travel * HARDOX rear wall mounted on pendulum bearings, with automatic tailgate release; * Drawbar for coupling heights unbel. approx. 820 - 970 mm * Galvanized drawbar, screwed in, with DIN screw drawbar eye Ø 50 mm * Reinforced 12 t gear support winch with load and fast gear * Lateral / rear tipping angle: 50 ° / 50 ° * Tipping bridge and superstructure KTL and powder-coated in color of choice * HOT-DIP GALVANIZED CHASSIS & DRAWBAR * EBS brake system with stability program in accordance with ECE directive * Spring-loaded parking brake * Hydraulic three-way tipping mechanism with control via the towing vehicle (max. 200 bar); three-stage telescopic cylinder, 1st stage Oxinite-coated, 2nd + 3rd stage salt-bath nitrided, with lift limiter and safety cables; SVK BG3 hydraulic plug-in coupling as single-circuit connection * 2 pairs of semi-circular mudguards with splash guard system * Chassis frame with drawbar hot-dip galvanized * 385/65 R22.5 tires * SAF air suspension with drum brake axles, electronically controlled for tilt stabilization * Electrical system: 15-pin 24 volt * Brake connection: 2 interchangeable coupling heads red/yellow ISO 1728 Cgsbvpvjkn N S Rjcist * Fixed underride guard Your advantages: * Optimum corrosion protection for the chassis/ drawbar thanks to hot-dip galvanizing in an immersion bath * Low tare weight => therefore high payload * Tipper body and superstructure KTL and powder-coated in the color of your choice * HARDOX superstructure for maximum load capacity --- Optional * Roll-up tarpaulin and platform --- ∗Stock vehicle - promptly available ∗Subject to prior sale ∗Price ex works

Condition: used, overall weight: 3,000 kg, maximum load weight: 2,130 kg, axle configuration: 2 axles, loading space length: 3,626 mm, first registration: 07/2020, total width: 2,022 mm, total height: 1,240 mm, Subject to errors and prior sale! Internal number: 1451. GW220985927 ---- See pictures for equipment and condition. ---- The vehicle is unprocessed! Nationwide delivery possible for an additional charge. Subject to errors and prior sale. Csbopxmg Nevpvcijgt We are happy to accept your vehicle as part payment. Financing / leasing also possible without a down payment! Do you have any questions? We are happy to advise you!

Condition: new, overall weight: 750 kg, maximum load weight: 365 kg, axle configuration: 1 axle, loading space length: 2,510 mm, loading space width: 1,320 mm, loading space height: 1,520 mm, total width: 1,810 mm, total height: 2,145 mm, HUMBAUR HK 7525-15 car box trailer 750 kg Rear wing door SURCHARGE: White ramp instead of rear door, Maximum load 300 kg, with ramp tip.....Price on request Technical data Trailer type: Single-axle Construction type: Plywood Total weight: 750 kg Payload: 365 kg Length (inside): 2510 mm Length (total): 35 mm Width (inside): 20 mm Width (total): 1810 mm Cgebvpvcon E Trroiot Height (inside): 1520 mm Height (total): 2105 mm Loading height: 535 mm Description Our single-axle car box trailer is constructed to be as stable as possible: hot-dip galvanized steel chassis, plastic seals on the doors, solid reinforcements in the roof area and the front wall - this trailer has a long service life. The integrated lashing system secures the load in the interior. A lamp provides sufficient light. This means your goods arrive reliably and undamaged. The perfect advertising medium: we can stick your individual advertising message onto the side walls of the single-axle trailer for an additional charge. You will benefit from this for a long time. Standard equipment * V-drawbar, hot-dip galvanized * -pin plug (without reversing light on HK 7525-15P) * Base plate 15 mm thick * Side walls and roof made of multi-layer wood, 15 mm thick, with UV-resistant plastic coating * Interior light installed * Single-leaf door at the rear on HKxx25, double-leaf door on HKxx3015 * Espagnolette lock and hinges galvanized * 6 lashing rings in the frame profile, tensile force 400 kg per lashing ring, Dekra tested * Support wheel NEW PRODUCT - Incl. invoice with VAT, braked 2 years TÜV/unbraked 3 years TÜV and 2-year guarantee. The vehicle documents can be sent in advance after the deposit or payment has been made so that you can register the trailer for collection. Some pictures do not correspond to the basic equipment Subject to errors and changes Collection from the main office Engelhard trailer wholesale market Steinauer Weg 15 91589 Aurach Tel: Fax: 9 Homepage: If desired, the handover can also take place in 06618 Wethau, (Gmach company) collection warehouse OST near Leipzig Tel. , Fax for an additional charge of 150.00 euros (if in stock there!). The handover fee is to be paid directly on site IMPORTANT! - If you would like to be picked up in Wethau, please call to inquire about availability! Opening hours: Monday - Friday 8:00 a.m. - 12:00 p.m. and .:00 a.m. - 5:00 p.m. Saturday 9:00 a.m. - .:00 p.m. Outside of these hours you can also send your enquiries at any time by fax 9.

Condition: new, overall weight: 18,000 kg, maximum load weight: 13,700 kg, axle configuration: 2 axles, loading space length: 5,030 mm, loading space width: 2,420 mm, loading space height: 600 mm, tire size: 435/50 r19,5, color: white, Equipment: ABS, tail-lift, trailer coupling, HUMBAUR 18.0 to tandem three-way tipper with ramp shaft, Typ. HTK 185024 Premium --- INCLUDING SAF air suspension with lifting & lowering function INCLUDING HOT-DIP GALVANIZED CHASSIS & DRAWBAR including lockable ramp cover with lid (privacy screen) Equipment: * Permissible total weight 18,000 kg * Payload approx. 13,700 kg * Loading area approx. 5,030 x 2,420 mm * Unloaded loading height approx. 1,135 mm * Overall dimensions: LxWxH approx. 7,000 x 2,550 x 1,750 mm * Bridge floor made of 4 mm fine-grained steel * Finishing of the tipper body and drop sides in the desired color (RAL 9010 pure white) or hot-dip galvanized * Laser-welded quality steel drop sides, 600 mm high * Side and rear drop sides can be folded down, removable and swinging with central locking bolted on * Removable rear stanchions * Dropside lifting springs on the side drop sides * Drawbar with spindle infinitely height-adjustable for coupling heights unbel. approx. 840 - 1,100 mm * DIN screw-type drawbar eye Ø 50 mm * Reinforced 12 t geared support winch with load and fast gear * SAF air suspension with lift & lower function * 10 6 t lashing rings recessed * Lateral / rear tipping angle: 45 ° / 48 ° * 2 telescopic folding supports at the rear of the vehicle Cgebvpvcskn N Sfjist * Lockable mounting shaft for 2 optional drive-on ramps integrated in the frame * 2-circuit air brake system * EBS brake system 24 volt * Spring-loaded parking brake * Hydraulic three-way tipping mechanism with control via the towing vehicle (max. 200 bar); five-stage tipping cylinder with lift limiter and safety cables; SVK BG3 hydraulic plug-in coupling as single-circuit connection; * Mudguards with splash guard system * Chassis frame with drawbar hot-dip galvanized * 435/50 R19.5 tires * Electrical system: 15-pin 24 volt * Brake connection: 2 interchangeable coupling heads red/yellow ISO 1728 Your advantages: * Optimum corrosion protection through hot-dip galvanizing * Lower loading height thanks to the 435 tires * Safe loading and unloading thanks to telescopic folding supports at the rear * Ideal load securing options thanks to standard lashing options * Height-adjustable drawbar enables compatibility with the different coupling heights of towing vehicles * Low tare weight => therefore high payload Optionally we offer you for an extra charge: * 1 pair of ALU drive-on ramps (10 t or 13 t/pair) with pin lock, length approx. 3,570 mm x width approx. 400 mm (tare weight approx. 65-75 kg/each) * Plastic toolbox mounted under the loading area * LED rear lights 24 Volt or LED multi-voltage system for 12&24 Volt ∗Stock vehicle - available immediately ∗Subsequent sale reserved ∗Price ex works

Condition: new, overall weight: 750 kg, maximum load weight: 585 kg, axle configuration: 1 axle, loading space length: 2,510 mm, loading space width: 1,310 mm, loading space height: 350 mm, HUMBAUR HA 7525 ALU WITHOUT front flap (with see surcharge below) Transport trailer Technical data: Trailer type: Single-axle Construction type: Aluminum Total weight: 750 kg Payload: 585 kg Length (inside): 2510 mm Length (total): 3580 mm Width (inside): 10 mm Width (total): 1760 mm Cgobvpvcotvtd Roist Height (inside): 350 mm Height (total): 865 mm Loading height: 510 mm Standard equipment: * V-drawbar hot-dip galvanized * -pin plug, reversing light from 751 kg permissible total weight * Base plate 15 mm thick * Side walls made of anodized, double-walled aluminum profile * Flap(s) with recessed locks * Lashing brackets (4 St. up to 2050 mm / 6 pcs. from 2510 mm box length) integrated in the side walls, pulling force 400 kg per lashing bracket, Dekra tested * Humbaur multifunctional lighting integrated in the underrun protection * Corner stanchions with insertion option Front flap .....Price on request Support wheel mounted ..... 35.00 euros incl. VAT PLEASE CALL US - we will be happy to advise you! NEW PRODUCT - Incl. invoice with VAT, braked 2 years TÜV / unbraked 3 years TÜV and 2 years guarantee. The vehicle documents can be sent in advance after the deposit or payment has been made so that you can register the trailer for collection. Some pictures do not correspond to the basic equipment Subject to errors and changes Collection from the main office Engelhard trailer wholesale market Steinauer Weg 15 91589 Aurach Tel: Fax: 9 Homepage: If desired, the handover can also take place in 06618 Wethau, (Gmach company) collection warehouse OST near Leipzig Tel. , Fax for an additional charge of 150.00 euros (if in stock there!). The handover fee is to be paid directly on site IMPORTANT! - If you would like to be picked up in Wethau, please call to inquire about availability! Opening hours: Monday - Friday 8:00 a.m. - 12:00 p.m. and .:00 a.m. - 5:00 p.m. Saturday 9:00 a.m. - .:00 p.m. Outside of these hours you can also send your enquiries at any time by fax 9.

Condition: new, overall weight: 1,900 kg, maximum load weight: 14,500 kg, axle configuration: 2 axles, loading space length: 7,200 mm, loading space width: 2,460 mm, loading space height: 870 mm, suspension: full air, tire size: 235/75 r17,5, Equipment: ABS, tail-lift, trailer coupling, HUMBAUR 19 to tandem low loader drive-over with rear bevel and folding steel ramps, Typ. HBTZ 197224 BS --- INCLUDING SAF air suspension with lifting/lowering valve INCLUDING HOT-DIP GALVANIZED CHASSIS/ DRAWBAR INCLUSIVE galvanized steel bulkhead 400 mm high, pluggable INCLUSIVE anodized aluminium drop sides 400 mm incl. galvanized central stanchions Equipment: * Total weight 19 tons (2x9 tons axle load and 1 ton drawbar load) * Payload approx. 14.5 tons (without BW superstructure) * 7,200 mm long loading area incl. rear slope * Loading height with unloaded vehicle approx. 870 mm * Steel bulkhead 400 mm high, pluggable * 400 mm anodized aluminium drop sides incl. galvanized central stanchions * Overall dimensions: LxWxH approx. 9,380 x 2,550 x 3,700 mm * Loading area slanted at the rear * Drive-on ramps with wooden decking, can be moved sideways * Steel ramps approx. 3,100 x 760 mm with spring lifting mechanism * Drive-on angle only approx. 11° * Low loader axles from SAF with closed S-cam brakes * Air suspension with lifting/lowering function * EBS brake system with stability program in accordance with ECE directive * Spring-loaded parking brake * Twin tires 235/75R17.5" * Galvanized drawbar, with DIN screw-in drawbar eye Ø 50 mm, infinitely adjustable via reinforced height adjustment * Coupling height approx. 750 - 1,000 mm * Reinforced 12 t geared support winch with load and fast gear * 8 10 t lashing rings recessed * 16 2 t drop lashing brackets can be lowered into the outer frame * 2 telescopic folding supports at the rear of the vehicle * Chassis, ramps and steel bulkhead hot-dip galvanized * Bridge floor with wooden decking and STEEL tear plate over the wheels * Mudguards with anti-spray system * 2 wheel chocks with holder * Electrical system: 15-pin 24 volt * Brake connection: 2 interchangeable coupling heads red/yellow ISO 1728 Your advantages: Cgjbvpvcokn N Sisijt * Optimum corrosion protection thanks to hot-dip galvanizing * Safe loading and unloading thanks to telescopic folding supports at the rear * Simple and easy handling of the steel access ramps thanks to the ramp lifters * Ideal load securing options thanks to standard lashing options * The infinitely height-adjustable drawbar enables compatibility with the different coupling heights of towing vehicles * Low tare weight => therefore high payload --- Optional * Hydraulic ramp hoist ∗Storage vehicle - promptly available ∗Subject to prior sale ∗Price ex works

Condition: new, overall weight: 1,500 kg, maximum load weight: 1,210 kg, axle configuration: 1 axle, loading space length: 2,300 mm, loading space width: 1,400 mm, loading space height: 300 mm, HUMBAUR HU 15 14 - 1500 kg Technical data: Trailer type: single-axle Construction type: aluminum Total weight: 1500 kg Payload: 1210 kg Length (inside): 00 mm Width (inside): 1400 mm Height (inside): 300 mm Loading height: 655 mm Standard equipment * V-drawbar combined with longitudinal beam hot-dip galvanized * Chassis and frame hot-dip galvanized * -pin plug, reversing light from 751 kg. permissible total weight * Base plate 15 mm thick * Side walls made of anodized, double-walled aluminum profile with drawbar locks, cpl. removable * 4 lashing brackets in the outer frame profile * Support wheel * Humbaur multifunctional lighting integrated in the underrun protection * Corner stanchions with insertion option Other accessories on request PLEASE CALL US - we will be happy to advise you! NEW PRODUCT - Incl. invoice with VAT, braked 2 years TÜV/unbraked 3 years TÜV and 2 years guarantee. The vehicle documents can be sent in advance after the deposit or payment has been made so that you can register the trailer for collection. Some pictures do not correspond to the basic equipment Subject to errors and changes Csbvpstpd Ifevcisgt Collection from the main office Engelhard trailer wholesale market Steinauer Weg 15 91589 Aurach Tel: Fax: 9 Homepage: If desired, the handover can also take place in 06618 Wethau, (Gmach company) collection warehouse OST near Leipzig Tel. , Fax for an additional charge of 150.00 euros (if in stock there!). The handover fee is to be paid directly on site IMPORTANT! - If you would like to be picked up in Wethau, please call to inquire about availability! Opening hours: Monday - Friday 8:00 a.m. - 12:00 p.m. and .:00 a.m. - 5:00 p.m. Saturday 9:00 a.m. - .:00 p.m. Outside of these hours you can also send your enquiries at any time by fax 9.

Condition: new, overall weight: 21,000 kg, maximum load weight: 16,400 kg, axle configuration: 2 axles, loading space length: 7,200 mm, loading space width: 2,540 mm, suspension: full air, tire size: 235/75 r17,5, Equipment: ABS, trailer coupling, HUMBAUR 21 to tandem low loader drive-over with rear bevel and folding steel ramps, Typ. HBTZ 217224 BS --- --- INCLUSIVE SAF air suspension with raise/lower function INCLUSIVE central axle lift on 1st axle INCLUSIVE galvanized 400 mm high solid steel bulkhead INCLUSIVE protected rear lights recessed in the end beam INCLUSIVE reinforced drawbar height adjustment by means of a spindle HOT-DIP GALVANIZED CHASSIS/DRAWBAR Equipment: * Permissible total weight 21,000 kg * Payload approx. 16,400 kg * Loading area approx. 7,200 x 2,540 mm * Unloaded loading height approx. 870 mm due to wheel wells * Overall dimensions: LxWxH approx. 8,700 x 2,550 x 3,710 mm * Galvanized 400 mm high solid steel bulkhead * Loading area slanted at the rear * Drive-on ramps with wooden decking, can be moved sideways (approx. 3,100 x 760 mm) * Spring jack as standard (hydraulic ramp jack at extra cost) * Approx. 13° drive-on angle * Reinforced infinitely variable drawbar height adjustment for coupling heights unbel. approx. 750 - 1,000 mm * DIN screw-type towing eye Ø 50 mm * Reinforced 12 t gear support winch with load and fast gear * Climbing rails welded to the drive-on slope * 8 10 t lashing rings countersunk * 16 2 t drop lashing brackets can be lowered into the outer frame * 2 telescopic folding supports at the rear of the vehicle * 2-circuit air brake system with ALB function * EBS brake system 24 volt with EBS plug-in connection ISO 7638;Note: towing vehicle must have ABS/EBS connection; * Spring-loaded parking brake * Steel mudguards, hot-dip galvanized * Floor and ramps with softwood planks * Chassis frame with towing tube hot-dip galvanized * 235/75 R17.5 tires (8-wheel) * Electrical system: 15-pin 24 volt * Brake connection: 2 interchangeable coupling heads red/yellow ISO 1728 Your advantages: * Optimum corrosion protection thanks to hot-dip galvanizing * Safe loading and unloading thanks to telescopic folding supports at the rear and climbing rails on the ramp slope * Simple and easy handling of the steel drive-on ramps thanks to the ramp lifters * Ideal load securing options thanks to standard lashing options * The reinforced, infinitely height-adjustable drawbar enables compatibility with the different coupling heights of towing vehicles * Low tare weight => therefore high payload Cobokn N Sxjvpvciogt --- Optional * Hydraulic ramp hoist ∗Storage vehicle - promptly available ∗Subject to prior sale ∗Price ex works

Condition: new, overall weight: 3,000 kg, maximum load weight: 2,340 kg, axle configuration: 2 axles, loading space length: 3,000 mm, loading space width: 1,600 mm, loading space height: 270 mm, total width: 2,200 mm, total height: 2,015 mm, HUMBAUR HS 30 30 16 - 3000 kg Machine transporter Technical data: Weight: 660 kg Total weight: 3,000 kg Payload: 2,340 kg Inner length: 3,000 mm - Total length: 4.0 mm Inner width: 1,600 mm Total width: 2,200 mm Inner height: 270 mm - Total height: 2,015 mm Loading height: 485 mm Tires: 14 inches Drawbar length approx. 1,530 mm Coupling height approx. 440 mm Plane length approx. 1,530 mm Plane width approx. 360 mm Standard equipment: Welded side wall/frame construction made of sheet steel, hot-dip galvanized Screwed V-drawbar, dip bath hot-dip galvanized 13-pin plug and reversing light Hot-dip galvanized steel ramps (1530 x 360mm) standing, load capacity per ramp 1500 kg, with anti-slip mesh covering and integrated support feet Lashing rings mounted in the outer frame 12 pieces (6 pairs) for 3000 mm and 14 pieces (7 pairs) for 3750 mm box length, pulling force 1000 kg per lashing ring Fully automatic support wheel Solid walkable steel fenders Other sizes, designs and equipment on request. PLEASE CALL US - we will be happy to advise you! Cgebvpvjr Nnnmscist NEW PRODUCT - Incl. invoice with VAT, 3 years TÜV and 2 years guarantee. The vehicle registration document can be sent after a deposit (550.00 euros) or payment in advance so that you can register the trailer for collection. Some of the pictures do not correspond to the basic equipment If desired, the handover can also take place in 06618 Wethau, Klein Wethau (Gmach company) near Leipzig. Tel., Fax for an additional charge of 200.00 euros. IMPORTANT! - If you would like to pick up in Wethau near Leipzig, please call us beforehand to check availability! Opening times: Monday - Friday 8.00 a.m. - 12.00 p.m. and 1.00 p.m. - 5.00 p.m. Saturday 9.00 a.m. - 1.00 p.m. Outside of these times, you can also send your enquiries at any time by fax:

Condition: new, overall weight: 40,000 kg, maximum load weight: 31,300 kg, axle configuration: > 3 axles, loading space length: 7,130 mm, loading space width: 3,000 mm, loading space height: 890 mm, suspension: full air, Equipment: ABS, center pivot plate, trailer coupling, Humbaur HTD40-K V20 Total weight 40,000 kg Payload approx. 31,350 kg Chassis frame hot-dip galvanized Bogie frame hot-dip galvanized Drive-on ramps hot-dip galvanized Air suspension with manual REAR lowering at the rear SAF axle with drum brake EBS electronic braking system Tires 235/75R17.5 – 16-fold Low bed length approx. 7160 mm Hole for excavator boom storage, approx. 3000 mm x 730 mm x 180 mm in the rear area of the low bed 4 pairs of lashing rings 10 tons sunk in the low bed 2 pairs of lashing rings 10 tons sunk in the high bed 4 pairs of lashing points 3 tons in the outer frame of the low bed 3 pairs of lashing eyes 6 tons on the outer frame 4 pairs of stake pockets in the outer frame of the high bed 4 pairs of stake pockets in the outer frame of the low bed 3-meter widening package with folding boom without slope 4 x warning signs with lighting Beacon at the rear Storage compartment under the loading area 2 storage compartments with hinged lid in the high plateau Hydraulic ramp jacks 1-part ramps approx. 3150 x 750 mm Softwood flooring for loading area and ramps 40,000 kg GVW only with special approval according to §70 ∗Stock vehicle - available immediately ∗Subject to prior sale ∗Price ex works Cgobvpvcskn N Sujiet

Condition: new, overall weight: 2,700 kg, maximum load weight: 2,140 kg, axle configuration: 1 axle, loading space length: 4,000 mm, loading space width: 2,140 mm, loading space height: 50 mm, total width: 2,190 mm, total height: 900 mm, HUMBAUR FTK 27 40 22 Car transporter Weight: 560 kg Total weight 2,700 kg Payload 2,140 kg Inner length 4,000 mm Total length 5,515 mm Inner width 2,140 mm Total width 2.0 mm Inner height 50 mm Total height 900 mm Loading height 610 mm 10 inch tires Standard equipment: Chassis bolted and galvanized * Galvanized tipping bridge * Tipping bridge can be tilted mechanically using shock absorbers * Steel loading ramps * V-drawbar hot-dip galvanized * -pin plug and reversing light * Support wheel Surcharge: Cable winch with cable winch bracket can be inserted on the right and left..... Price on request With the new tiltable vehicle transporter FTK from Humbaur allows you to transport your vehicle comfortably and safely. The FTK now offers the advantages of tiltable vehicle trailers in the compact class. Ideal for vehicle repair service companies or private users for transporting small vehicles such as a Smart or VW Golf. The new Humbaur FTK offers all the advantages of tiltable vehicle transporters - for the first time in a compact version. You can tilt the bridge mechanically using shock absorbers and drive the trailer effortlessly over grooved steel loading ramps. The optional cable winch and the tilting hydraulics make loading even easier. Four variants with a payload of up to two tons and different dimensions allow you to choose a tailor-made, inexpensive model. The well thought-out and stable design ensures an optimally utilized usable area and a low loading angle. Galvanized components and the numerous options for securing loads confirm the quality in detail from Humbaur. PLEASE CALL US - we will be happy to advise you! NEW PRODUCT - Incl. invoice with VAT, braked 2 years TÜV/unbraked 3 years TÜV and 2 years guarantee. The vehicle documents can be sent in advance after the deposit or payment has been made so that you can register the trailer for collection. Some images do not correspond to the basic equipment Subject to errors and changes Collection from the main office Engelhard trailer wholesale market Steinauer Weg 15 91589 Aurach Tel: Fax: 9 Homepage: On request, the handover can also take place in 06618 Wethau, (Gmach company) collection warehouse OST near Leipzig Tel. , Fax for an additional charge of 150.00 euros (if in stock there!). The handover fee is to be paid directly on site IMPORTANT! - If you would like to pick up in Wethau, please call us in advance to check availability! Opening hours: Monday - Friday 8:00 a.m. - 12:00 p.m. and .:00 a.m. - 5:00 p.m. Cebvpvceutwn Neijgt Saturday 9:00 a.m. - .:00 p.m. Outside of these times, you can also send your enquiries at any time by fax 9.

Condition: new, overall weight: 11,900 kg, empty load weight: 2,500 kg, maximum load weight: 9,400 kg, axle configuration: 2 axles, loading space length: 6,200 mm, loading space width: 2,460 mm, loading space height: 400 mm, tire size: 235/75 r17,5, Equipment: ABS, tail-lift, trailer coupling, HUMBAUR 11.9 to tandem low-loader drive-over with ramp shaft, Typ. HBT 106224 BE (planks can be pushed in) INCLUDING side walls made of aluminium, anodized INCLUDING HOT-DIP GALVANIZED CHASSIS/ DRAWBAR Equipment: Cjbvpskn N R Novciogt * Permissible total weight 11,900 kg * Payload approx. 9,400 kg * Loading area approx. 6,200 x 2,460 mm * Unloaded loading height approx. 920 mm * Overall dimensions: LxWxH approx. 8,140 x 2,550 x 1,400 mm * Aluminium drop sides, anodized, can be folded down at the sides, removable; galvanized corner stanchions, pluggable at the front and rear * Lockable mounting shaft for optional aluminum ramps in the chassis frame * Infinitely height-adjustable drawbar for coupling heights of approx. 700 - 1,000 mm * Reinforced 12 t geared support winch with load and fast gear * BPW axles * 6 pcs. 6 t lashing rings countersunk * 14 2 t drop lashing hoops can be lowered into the outer frame * 2 telescopic folding supports at the rear of the vehicle * 2-circuit air brake system with ALB function * ABS braking system 24 volt * Spindle parking brake * Steel mudguards, hot-dip galvanized * Floor made of softwood planks * Chassis frame with drawbar hot-dip galvanized * 235/75 R17.5 tires * Maintenance-free parabolic suspension with load compensation * Electrical system: 15-pin 24 volt * Brake connection: 2 interchangeable coupling heads red/yellow ISO 1728 Your advantages: * High-quality and corrosion-protected anodized aluminium side wall construction * Optimum corrosion protection thanks to hot-dip galvanizing in an immersion bath * Safe loading and unloading thanks to telescopic folding supports at the rear * Simple and easy handling thanks to the patented securing system of the ALU drive-on ramps * Lockable pick-up shaft * Ideal load securing options thanks to standard lashing options * The infinitely height-adjustable drawbar enables compatibility with the different coupling heights of towing vehicles * Low tare weight => therefore high payload Optionally we offer you for an extra charge: * 1 pair of ALU drive-on ramps (8 t/pair) with patented locking system, length approx. 3,570 mm x width approx. 400 mm (tare weight approx. 55 kg/each) ∗Storage vehicle - promptly available ∗Subject to prior sale ∗Price ex works

Condition: new, overall weight: 13,000 kg, empty load weight: 2,800 kg, maximum load weight: 10,200 kg, axle configuration: 2 axles, loading space length: 6,200 mm, loading space width: 2,460 mm, loading space height: 3,260 mm, tire size: 245/70 r17,5, Equipment: ABS, tail-lift, trailer coupling, HUMBAUR 13.0 to tandem low-loader drive-over with rear bevel and folding steel ramps, Typ. HBT 136224 BS INCLUDING galvanized grating on the rear ramps INCLUDING aluminium drop sides, anodized HOT-DIP GALVANIZED CHASSIS/ DRAWBAR Equipment: * Permissible total weight 13,000 kg * Payload approx. 10,200 kg * Loading area approx. 6,200 x 2,460 mm * Unloaded loading height approx. 920 mm * Overall dimensions: LxWxH approx. 8,350 x 2,550 x 3,260 mm * 400 mm high side walls made of aluminium, anodized, can be folded down at the sides, removable; galvanized corner stanchions, pluggable at the front and rear * Loading area slanted at the rear * Drive-on ramps with galvanized grating, can be moved sideways (approx. 2,600 x 540 mm) with one gas strut jack per ramp * Infinitely height-adjustable drawbar for coupling heights unbel. approx. 700 - 1,000 mm * Reinforced 12 t geared support winch with load and fast gear * 6 6 t lashing rings recessed * 14 2 t drop lashing hoops can be lowered into the outer frame * 2 telescopic folding supports at the rear of the vehicle * 2-circuit air brake system with ALB function * ABS braking system 24 volt * Spindle parking brake * Steel mudguards, hot-dip galvanized * Floor made of softwood planks * Chassis frame with drawbar hot-dip galvanized * Tires 245/70 R17.5 * Maintenance-free parabolic suspension with load compensation * Electrical system: 15-pin 24 volt Cgsbskn N R Tjvpvciot * Brake connection: 2 interchangeable coupling heads red/yellow ISO 1728 Your advantages: * High-quality and corrosion-protected anodized aluminium side wall construction * Optimum corrosion protection thanks to hot-dip galvanizing in an immersion bath * Safe loading and unloading thanks to telescopic folding supports at the rear and the anti-slip grating ramp covering * Simple and easy handling of the steel access ramps thanks to the ramp lifters * Ideal load securing options thanks to standard lashing options * The infinitely height-adjustable drawbar enables compatibility with the different coupling heights of towing vehicles * Low tare weight => therefore high payload ∗Stock vehicle - promptly available ∗Subsequent sale reserved ∗Price ex works

Condition: new, overall weight: 30,000 kg, maximum load weight: 23,500 kg, axle configuration: 3 axles, loading space length: 8,550 mm, loading space width: 2,550 mm, loading space height: 880 mm, Equipment: ABS, center pivot plate, trailer coupling, HUMBAUR 3-axle turntable low loader with offset loading area/high platform, Typ. HTD309525-K - PARABLE SUSPENSION - V2-Plus --- INCLUSIVEChassis frame and bogie hot-dip galvanized INCLUSIVE parabolic suspension with rear axle compensation unit INCLUSIVE ABS brake system (suitable for tractor and truck) INCLUSIVE 12 & 24 volt LED multi-voltage lighting system INCLUSIVE warning package and rotating beacon INCLUSIVE stake pockets & lashing ring package INCLUSIVE storage box at the top front of the platform, with hinged lid INCLUSIVE 3-meter package with storage compartment Equipment: * 24-month warranty * Gross vehicle weight 30,000 kg * Payload approx. 23,500 kg * Chassis frame and bogie hot-dip galvanized * Parabolic suspension with rear axle compensation unit * ABS brake system (suitable for tractors and trucks) * 12 & 24 volt LED multi-voltage lighting system, 15-pin 24 volt connection and 13-pin adapter * Loading height approx. 880 mm * 235/75R17.5 tires - 12-ply * Low loading platform 6,500 mm incl. ramp * B dimension 10,760 mm * Drawbar with 8° inclined drawbar eye Ø 40 mm, height-adjustable * 3-fold towing fork mount for various truck coupling heights * Storage box at the top front of the plateau, with hinged lid * 3 pairs of lashing rings 10 to. recessed in the low bed * 2 pairs of lashing rings 10 to. recessed in the high bed * 4 pairs of lashing points 3 tons in the outer frame of the low bed * 3 pairs of lashing eyes 6 to. screwed to the outer frame * 4 pairs of lashing points 2 to. over wheel cut-out 2nd and 3rd axle * 6 pairs of stanchion pockets in the outer frame (stanchion pocket package) Cgjbvjkn N S Aopvciot * Chassis frame and bogie hot-dip galvanized * 1-section ramps approx. 3150 x 750 mm with spring lifting mechanism and mech. displacement * Drive-on angle approx. 10-11° * Softwood covering for loading area and ramps * Pendulum support feet at the rear * 3-meter widening package with folding boom, wooden planks * Sheet steel tool box under the cargo bed, lockable, mounted on the side under the cargo bed as a storage compartment for wooden planks * Climbing rails welded to the ramp slope * 30,000 kg GVW only with special permit in accordance with §70 * Brake connection: red/yellow * Warning package and rotating beacon --- Optional variants at extra cost: * V2 Plus with hydr. ramp lift = € 1,000 net surcharge * V2 PlusPlus (spring lifter) with excavator trough = 700 € net surcharge * V2 PlusPlus with hydr. ramp lift & excavator trough = € 1,700 net surcharge --- ∗Stock vehicle - available immediately ∗Subject to prior sale ∗Price ex works

Condition: new, overall weight: 30,000 kg, maximum load weight: 24,000 kg, axle configuration: 3 axles, loading space length: 8,550 mm, loading space width: 2,550 mm, loading space height: 880 mm, Equipment: ABS, center pivot plate, trailer coupling, HUMBAUR 3-axle turntable low loader with offset loading area/high platform, Typ. HTD309525-K - PARABOLIC SUSPENSION - V2 Csbvskn N R Espvcisgt --- INCLUSIVEChassis frame and bogie hot-dip galvanized INCLUSIVE parabolic suspension with rear axle compensation unit INCLUSIVE ABS braking system (suitable for tractor and truck) INCLUSIVE 12 & 24 volt LED multi-voltage lighting system INCLUSIVE warning package and rotating beacon Equipment: * 24 months warranty * Gross vehicle weight 30,000 kg * Payload approx. 24,000 kg * Chassis frame and bogie hot-dip galvanized * Parabolic suspension with rear axle compensation unit * ABS brake system (suitable for tractors and trucks) * 12 & 24 volt LED multi-voltage lighting system, 15-pin 24 volt connection and 13-pin adapter * Loading height approx. 880 mm * 235/75R17.5 tires - 12-ply * Low loading platform 6,500 mm incl. ramp * B dimension 10,760 mm * Drawbar with 8° inclined drawbar eye Ø 40 mm, height-adjustable * 3-fold towing fork mount for various truck coupling heights * 3 pairs of lashing rings 10 tons recessed in the drop deck * 2 pairs of lashing rings 10 to. recessed in the high bed * 4 pairs of lashing points 3 tons in the outer frame of the low bed * 4 pairs of lashing points 2 tons above wheel cut-out 2nd and 3rd axle * Chassis frame and bogie hot-dip galvanized * 1-section ramps approx. 3150 x 750 mm with spring lifting gear and mech. displacement * Drive-on angle approx. 10-11° * Softwood covering for loading area and ramps * Pendulum support feet at the rear * Climbing rails welded to the ramp slope * 30,000 kg GVW only with special permit according to §70 * Brake connection: red/yellow * Warning package and rotating beacon --- Modular design for easy retrofitting of 3 m folding extension, storage box in the high bed, plank box under the cargo bed, etc. --- ∗Stock vehicle - promptly available ∗Subject to prior sale ∗Price ex works

Condition: new, overall weight: 21,000 kg, empty load weight: 4,600 kg, maximum load weight: 166,400 kg, axle configuration: 2 axles, loading space length: 6,500 mm, loading space width: 2,540 mm, loading space height: 3,710 mm, suspension: air/air, tire size: 235/75 r17,5, Equipment: ABS, trailer coupling, HUMBAUR 21 to tandem low-loader drive-over trailer with rear bevel and folding steel ramps, Typ. HBTZ 216524 BS --- --- INCLUSIVE SAF air suspension with raise/lower function INCLUSIVE central axle lift on 1st axle INCLUSIVE galvanized 400 mm high solid steel bulkhead INCLUSIVE protected rear lights recessed in the end beam INCLUSIVE reinforced drawbar height adjustment by means of a spindle --- --- HOT-DIP GALVANIZED CHASSIS/TRACTION TUBE Equipment: * Permissible total weight 21,000 kg Cebvpskcuyzevcisgt * Payload approx. 16,400 kg * Loading area approx. 6,500 x 2,540 mm * Loading height unloaded approx. 870 mm due to wheel wells * Overall dimensions: LxWxH approx. 8,700 x 2,550 x 3,710 mm * Galvanized 400 mm high solid steel bulkhead * Loading area slanted at the rear * Drive-on ramps with wooden decking, can be moved sideways (approx. 3,100 x 760 mm) * Spring jack as standard (hydraulic ramp jack at extra cost) * Approx. 13° drive-on angle * Reinforced infinitely variable drawbar height adjustment for coupling heights unbel. approx. 750 - 1,000 mm * DIN screw-type towing eye Ø 50 mm * Reinforced 12 t gear support winch with load and fast gear * Climbing rails welded to the drive-on slope * 8 10 t lashing rings countersunk * 16 2 t drop lashing brackets can be lowered into the outer frame * 2 telescopic folding supports at the rear of the vehicle * 2-circuit air brake system with ALB function * EBS brake system 24 volt with EBS plug-in connection ISO 7638;Note: towing vehicle must have ABS/EBS connection; * Spring-loaded parking brake * Steel mudguards, hot-dip galvanized * Floor and ramps with softwood planks * Chassis frame with towing tube hot-dip galvanized * 235/75 R17.5 tires (8-ply) * Electrical system: 15-pin 24 volt * Brake connection: 2 interchangeable coupling heads red/yellow ISO 1728 Your advantages: * Optimum corrosion protection thanks to hot-dip galvanizing * Safe loading and unloading thanks to telescopic folding supports at the rear and climbing rails on the ramp slope * Simple and easy handling of the steel drive-on ramps thanks to the ramp lifters * Ideal load securing options thanks to standard lashing options * The reinforced, infinitely height-adjustable drawbar enables compatibility with the different coupling heights of towing vehicles * Low tare weight => therefore high payload --- Optional * Hydraulic ramp hoist ∗Storage vehicle - promptly available ∗Subject to prior sale ∗Price ex works

Condition: new, overall weight: 14,400 kg, maximum load weight: 107,000 kg, axle configuration: 2 axles, loading space length: 6,200 mm, loading space width: 2,460 mm, loading space height: 850 mm, suspension: parabolic leaf (spring), Year of construction: 2024, Equipment: tail-lift, HUMBAUR 14.4 to tandem low-loader drive-over trailer (twin tires) with rear bevel and folding steel ramps, Typ. HBTZ 146225 BS INCLUDES galvanized grating on the rear access ramps INCLUDING aluminium drop sides, anodized HOT-DIP GALVANIZED CHASSIS/ DRAWBAR Equipment: Permissible total weight 14,400 kg Payload approx. 10,700 kg Loading area approx. 6,200 x 2,460 mm Unloaded loading height approx. 850 mm Overall dimensions: LxWxH approx. 8,370 x 2,550 x 3,260 mm 400 mm high side walls made of aluminium, anodized, can be folded down at the sides, removable; galvanized corner stanchions, pluggable at the front and rear Loading area slanted at the rear Drive-on ramps with galvanized grating, can be moved sideways (approx. 2,400 x 540 mm) with one gas strut jack per ramp Drawbar continuously height-adjustable for coupling heights of approx. 600 - 900 mm Reinforced 12 t geared support winch with load and fast gear BPW axles 6 pieces 6 to. Lowered lashing rings 14 pcs. 2 to. Lowerable drop lashing bracket in the outer frame 2 telescopic folding supports at the rear of the vehicle 2-circuit air brake system EBS brake system 24 volt Spring-loaded parking brake Cebvpjvbykyjvcijgt TPMS tire pressure monitoring system Complete LED lighting Flashing side marker lights Steel mudguards, hot-dip galvanized Floor made of softwood planks, painted/impregnated Chassis frame with drawbar hot-dip galvanized Tires 205/65 R17.5 (8-wheel) Maintenance-free parabolic suspension with load compensation Electrical system: 15-pin 24 volt Brake connection: 2 interchangeable coupling heads red/yellow ISO 1728 Your advantages: Low loading height thanks to 205 twin tires High-quality and corrosion-protected anodized aluminium dropside superstructure Optimum corrosion protection thanks to hot-dip galvanizing in an immersion bath Safe loading and unloading thanks to telescopic folding supports at the rear and the anti-slip grating ramp covering Simple and easy handling of the steel access ramps thanks to the ramp lifters Ideal load securing options thanks to standard lashing options The infinitely height-adjustable drawbar enables compatibility with the different coupling heights of towing vehicles Low tare weight => therefore high payload Optionally we offer you against surcharge: Plastic toolbox under the loading area ATTENTION: Example pictures, equipment may vary! *Stock vehicle - available immediately *Subject to prior sale *Price ex works - Gersthofen

Condition: new, overall weight: 11,900 kg, maximum load weight: 9,500 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,010 mm, loading space height: 250 mm, tire size: 235/75 r17,5, Equipment: ABS, trailer coupling, HUMBAUR 11.9 to tandem low-loader drive-through (wheels outside), Typ. HS 105020 BS --- INCLUDING galvanized grating on the access ramps at the rear Cgebvpvcokn N S Heist --- HOT-DIP GALVANIZED CHASSIS/ DRAWBAR Equipment: * Permissible total weight 11,900 kg * Payload approx. 9,500 kg * Loading area approx. 5,000 x 2,010 mm * Loading height unloaded approx. 700 mm * Overall dimensions: LxWxH approx. 7,160 x 2,550 x 3,000 mm * Drive-on ramps with galvanized grating, can be moved sideways (approx. 2,400 x 540 mm) with one gas strut lift per ramp * Infinitely height-adjustable drawbar for coupling heights of approx. 700 - 850 mm * Reinforced 12 t geared support winch with load and fast gear * 4 6 t lashing rings (recessed in the corners) * 12 2 t drop lashing hoops can be lowered into the outer frame * 2 telescopic folding supports at the rear of the vehicle * 2-circuit air brake system with ALB function * ABS braking system 24 volt * Spindle parking brake * Steel mudguards, hot-dip galvanized * Floor made of softwood planks * Chassis frame with drawbar hot-dip galvanized * 235/75 R17.5 tires * Maintenance-free parabolic suspension with load compensation * Electrical system: 15-pin 24 volt * Brake connection: 2 interchangeable coupling heads red/yellow ISO 1728 Your advantages: * Low loading and installation height * Optimum corrosion protection thanks to hot-dip galvanizing * Safe loading and unloading thanks to telescopic folding supports at the rear and the anti-slip grating ramp surface * Simple and easy handling of the steel access ramps thanks to the ramp lifters * Ideal load securing options thanks to standard lashing options * The infinitely height-adjustable drawbar enables compatibility with the different coupling heights of towing vehicles * Low tare weight => therefore high payload TOP! On request, we are happy to offer you a visible paint finish (front, side walls, mudguards and rear cross member) on the galvanized chassis in your corporate color, see example pictures. ∗Stock vehicle - available immediately ∗Subject to prior sale ∗Price ex works

Condition: new, overall weight: 21,000 kg, maximum load weight: 16,200 kg, axle configuration: 2 axles, loading space length: 7,250 mm, loading space width: 2,540 mm, suspension: full air, tire size: 235/75 r17,5, Equipment: ABS, trailer coupling, HUMBAUR 21 to tandem low-loader drive-over trailer with rear bevel and folding steel ramps, Typ. HBTZ 217224 BS --- --- INCLUSIVE SAF air suspension with raise/lower function INCLUSIVE central axle lift on 1st axle INCLUSIVE galvanized 400 mm high solid steel bulkhead INCLUSIVE protected rear lights recessed in the end beam INCLUSIVE reinforced drawbar height adjustment by means of a spindle HOT-DIP GALVANIZED CHASSIS/DRAWBAR Equipment: * Permissible total weight 21,000 kg * Payload approx. 16,200 kg * Loading area approx. 7,250 x 2,540 mm * Unloaded loading height approx. 870 mm due to wheel wells * Overall dimensions: LxWxH approx. 9,400 x 2,550 x 3,710 mm * Galvanized 400 mm high solid steel bulkhead * Loading area slanted at the rear * Drive-on ramps with wooden decking, can be moved sideways (approx. 3,100 x 760 mm) with spring lifting mechanism for each ramp * Approx. 13° drive-on angle * Reinforced, infinitely variable drawbar height adjustment for coupling heights of approx. 750 - 1,000 mm * DIN screw-type drawbar eye Ø 50 mm * Reinforced 12 t gear support winch with load and fast gear * Climbing rails welded to the drive-on slope * 8 10 t lashing rings countersunk * 16 2 t drop lashing brackets can be lowered into the outer frame * 2 telescopic folding supports at the rear of the vehicle * 2-circuit air brake system with ALB function * EBS brake system 24 volt with EBS plug-in connection ISO 7638;Note: towing vehicle must have ABS/EBS connection; * Spring-loaded parking brake * Steel mudguards, hot-dip galvanized * Floor and ramps with softwood planks * Chassis frame with towing tube hot-dip galvanized Cebvekn N Rwepvcijgt * 235/75 R17.5 tires (8-ply) * Electrical system: 15-pin 24 volt * Brake connection: 2 interchangeable coupling heads red/yellow ISO 1728 Your advantages: * Optimum corrosion protection thanks to hot-dip galvanizing * Safe loading and unloading thanks to telescopic folding supports at the rear and climbing rails on the ramp slope * Simple and easy handling of the steel drive-on ramps thanks to the ramp lifters * Ideal load securing options thanks to standard lashing options * The reinforced, infinitely height-adjustable drawbar enables compatibility with the different coupling heights of towing vehicles * Low tare weight => therefore high payload --- Optional * Hydraulic ramp hoist ∗Storage vehicle - promptly available ∗Subject to prior sale ∗Price ex works

Condition: new, overall weight: 48,000 kg, maximum load weight: 38,000 kg, axle configuration: 3 axles, loading space length: 12,180 mm, loading space width: 3,000 mm, loading space height: 890 mm, suspension: full air, Equipment: ABS, HUMBAUR 3-axle low loader semi-trailer with offset loading area, Typ. HTS30K-V44+ --- INCLUSIVE lift axle INCLUSIVE self-steering axle with SAF air suspension INCLUSIVE 3-meter package INCLUSIVE stowage box under cargo bed INCLUSIVE TIM/WABCO Smart Board for axle load display INCLUSIVE Hot-dip galvanized chassis INCLUSIVE ALU drop sides and stowage box to the semi-trailer platform INCLUSIVE stake pockets and lashing ring package INCLUSIVE excavator trough Equipment: V44+ * Gross vehicle weight 48,000 kg * Payload approx. 38,000 kg * Chassis frame and ramps hot-dip galvanized * SAF air suspension unit including lifting and lowering * INCLUSIVE hot-dip galvanized chassis * Lift axle with starting aid and self-steering axle * EBS electronic braking system * WABCO Smart Board for axle load display * LED lighting system * Loading height approx. 890 mm * Saddle height: approx. 1,230 mm * 235/75R17.5 tires - 12-ply * Drop deck length approx. 8,680 mm incl. slope * Saddle platform length approx. 3,500 mm incl. slope * Excavator trough * 2" kingpin can be offset by 340 mm for 2+3-axle SPM * Gooseneck with 400 mm bulkhead * 400 mm folding aluminum side wall + storage box with lid * Ramp rail at the offset to the gooseneck * 3 pairs of lashing rings 6 tons sunk into the raised bed * 3 pairs of lashing points 3 tons in the bunk bed outer frame * 5 pairs of lashing rings 10 to. recessed in the low bed * 3 pairs of lashing eyes 6 to. screwed to the outer frame * 3 pairs of stake pockets in the outer frame of the high bed * 5 pairs of stanchion pockets in the low bed outer frame * 3-meter widening package with folding boom, wooden planks * Sheet steel toolbox under the cargo bed, lockable, mounted on the side under the cargo bed as a storage compartment for wooden planks * Warning package with lighting * Rotating beacon at the rear * 1-section ramps approx. 3150 x 750 mm - drive-on angle approx. 10° * Softwood flooring on ramps, low loading & semi-trailer platform * Spring lifting gear to the ramps * COC papers * 48,000 kg GVW only with special permit according to §70 * Climbing rails on the ramp slope Cebvpvcekn N S Ueiegt * Brake connection: red/yellow * Electrical system: 3-way socket with 2x7-pin socket (1 x ISO 1185 / 1x ISO 3731, 24 V-N/24 V-S) and 15-pin socket ISO 12098 --- Example pictures - equipment may vary ! ∗Stock vehicle - promptly available ∗Subsequent sale reserved ∗Price ex works