Low loader semitrailer

Goldhofer Semitieflader MPA3

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Hedpfstx Nwnox Afnel Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: excellent (used), axle configuration: 2 axles, first registration: 03/2015, loading space length: 134,450 mm, loading space width: 2,550 mm, loading space height: 480 mm, suspension: hydraulics, Year of construction: 2015, Equipment: ABS, = Additional options and equipment = - Central lubrication = Further information = Axle configuration Suspension: hydraulic suspension Rear axle 1: Max. axle load: 12,000 kg; Steered Rear axle 2: Max. axle load: 12,000 kg; Steered Weights Unladen weight: 12,660 kg Payload: 34,340 kg Gross vehicle weight: 47,000 kg Functional Hsdpfxsvtc Ais Afnjl Loading platform height: 48 cm Extendable body: Yes Condition Technical condition: very good Visual condition: very good Financial information Price: On request Further information Contact David F Middelman for more information.

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm Hedorgzv Nspfx Afnel LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, 3-axle MULTIMAX PLUS low-bed semi-trailer, air-suspended and hydraulically forced-steered axles. Technical Data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h Legal Gross vehicle weight: 49,500 kg / 31,500 kg Fifth-wheel load: 18,000 kg Axle load: 31,500 kg / 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm King pin trailing radius (rearwards) approx.: 2,100 mm Saddle height loaded approx.: 1,205 mm Loading platform length approx.: 9,600 mm Extendable by approx.: ? Loading platform width approx.: 2,540 mm Loading height at max. load approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle spacing: 1,360 mm Gross vehicle weight depending on fifth-wheel load: Yes Special permit is required for exceeding country-specific regulations. Technical Description Gooseneck: Gooseneck in SNT Design for optimized loading platform length, length approx. 3,900 mm, rear with chamfer approx. 1,000 mm x 6°. Technical fifth-wheel load: 18,000 kg. For tractor units: 4 x 2 and 6 x 2. Loading platform: Loading platform, length approx. 9,600 mm with rear chamfer approx. 900 mm x 6°. Loading platform behind the gooseneck hydraulically raisable and lowerable, length approx. 3,000 mm, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS A pair of two-part AXS steel ramps approx. 4,920 mm long and approx. 900 mm wide. Open grating surface. Hydraulically folding ramp tips. Ramps can be hydraulically shifted individually by approx. 235 mm outwards and approx. 365 mm inwards. Maximum load capacity and approach angle per technical data sheet: C470319 Maximum ramp angle with lowered loading platform: 9° Axles and Suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg Air suspension with lift/lower valve. Axle tool kit. Hjdpfxoizu Nte Afnsl Tyres: 235/75 R 17.5 3PMSF twin tyres. Manufacturer of our choice Load index 143/141J (144/144F) Braking system: WABCO EBS-E braking system according to EU regulations. Without connecting cable to tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" version as per EU regulations. (ASS 3) Metalizing: Complete HRM metalizing (High Resistance Metallisation) Complete steel structure shot blasted, then hot-finished with ZINACOR 850 (Zinc 85% - Aluminium 15%). Painting 6K final treatment: Complete steel structure shot blasted after welding. 1 coat zinc-based primer, 1 coat bonding primer. Final painting with 2 coats 2K (acrylic) single-colour in RAL shades of your choice, then cavity sealing with special wax. Rims in silver. Multi-colour and special painting at extra cost. Steel construction: Steel structure made of high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified to DIN-EN 287-1. MAG welding process to EN ISO 4063. Protective gas M21 per EN ISO 14175 Front wall of steel, plug-in, approx. 400 mm high Connection board for supply lines to the tractor unit at the height of the outer frame profile. ASPÖCK-UNIBOX at the front plug connection board with sockets 24N, 24S & 15-pin. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pin connection according to ISO-12098 If your pin configuration deviates from the ISO standard, please inform us. “Anderson” socket at the front connection board. Rema 78051-00 & Amp. 150 V. Cable for supply to electro-hydraulic unit and/or electric winch (35 mm²,

Condition: new, maximum load weight: 31,500 kg, overall weight: 42,000 kg, axle configuration: 3 axles, Year of construction: 2025, Equipment: ABS, Wiese 3-axle semi-trailer with lift table and fold-down rear. Ideal for transporting forklift trucks and/or work platforms. Technical data. Hodsvw Hmtspfx Afnol 3 x 10 to. axles Lift axle Steering axle Smart Steering (steers forwards and backwards) Outer beam chassis with slope 18-tonne neck design suitable for 2- and 3-axle semitrailer tractors Lifting table hydraulically movable in 3 positions Rear in folding rear design incl. hydraulic extensions, can be used as drive-on ramps, drive-over ramps or as a loading area (overall length reduction when rear is raised) Remote control for ramps and lift table Front wall Grid floor Numerous lashing points SmartBoard Central lubrication system Spray-galvanized and painted steel construction Numerous optional extras are available: e.g: Cable winch Storage box on the saddle step aluminum rims Further information on request.

Condition: used, maximum load weight: 42,500 kg, overall weight: 60,000 kg, axle configuration: 3 axles, first registration: 06/2022, with 12 axles, hydraulically suspended and divided, with hydromechanical forced steering, rear taper and drive-on ramps STZ-L Gooseneck - Robust welded steel construction - Engineered loading platform 3,950 x 2,480 mm including rear taper - Hydromechanical forced steering (dual-circuit steering system) - Turntable-mounted fifth-wheel plate with interchangeable 2-inch or 3.5-inch kingpin and adjustable steering wedge - Fifth wheel load: 24 t - Rear max. steering radius: 2,600 mm Loading platform - Lowered outer sections 4,630 mm long, 420 mm deep, resulting in a loading height of 470 mm or 830 mm with floor inserts - Extendable by 2,053 mm - Includes aluminum bridging rails for creating level surfaces - Excavator boom trough at rear running gear: 4,900 mm long, 880 mm wide, 480 mm deep - Length of rear running gear: 4,900 mm incl. 500 mm rear taper, loading height 890 mm - One pair of wheel recesses in lower deck - 3-axle hydraulically suspended running gear - Split Gigant axles with 600 mm stroke Rear of vehicle Hodpfx Asw Etd Tjfnjl - Tapered design, 500 mm - Rear hydraulic support Drive-on ramps - Two-part drive-on ramps, 2,850 + 1,850 mm long, 800 mm wide - Rubber-coated with climbing bars Braking system - Dual-line full air braking system with diaphragm brake cylinders - Automatic load-dependent brake (ALB) - Automatic slack adjusters (AGS) - Parking brake via spring-loaded cylinders - ABS brake Special equipment Radio remote control for steering and ramp operation Central lubrication system Technical data Gooseneck Loading platform (LxW): 3,950 x 2,480 mm Loaded fifth wheel height: 1,300 mm Loading platform Platform (LxW): 10,030 x 2,850 mm, extendable by 2,053 mm Lowered outer sections: 4,630 mm + 2,053 mm extension Center beam: 980 mm Excavator trough: 4,900 mm long, 880 mm wide, 480 mm deep Steering 1st to 3rd axle: hydromechanically forced steered (dual-circuit system)

Condition: used, empty load weight: 9,480 kg, maximum load weight: 31,520 kg, first registration: 03/2020, next inspection (TÜV): 04/2024, total length: 11,500 mm, total width: 25,500 mm, total height: 38,000 mm, suspension: air, tire size: 245/70 R 17.5/10mm, wheelbase: 1,800 mm, front tire size: 245/70 R 17.5/10mm, operation weight: 41,000 kg,

Condition: used, overall weight: 45,000 kg, axle configuration: 3 axles, first registration: 09/2017, * SAF axles * Wheel recesses * Hydraulic loading ramps, width adjustable * Air suspension Hedpfx Aowta Aljfnjl * Extendable * Unladen weight: 11,020 kg -----Internal vehicle number: 11010----Subject to errors and prior sale. WhatsApp support available! If you have questions about the vehicle or need further information, feel free to contact us conveniently via WhatsApp. WhatsApp: German, English -- WhatsApp: German, English, Arabic

Condition: new, empty load weight: 10,900 kg, maximum load weight: 37,100 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 9,600 mm, loading space width: 2,540 mm, loading space height: 890 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, operation weight: 10,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, with a bevel at the rear of approx. 1,000 mm x 6° -Technical fifth wheel load: 18,000 kg -For tractor units: 4 x 2 and 6 x 2 Loading area: -Loading area, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6° -Loading area can be raised and lowered hydraulically after the gooseneck, length approx. 3,000 mm, load capacity up to approx. 9,000 kg -Grating and sheet metal floor approx. 5 mm as additional reinforcement on the bevel of the loading area Ramps: -A pair of two-part AXS steel ramps with a length of approx. 4,675 mm and a width of approx. 900 mm -Grating floor -Hydraulically hinged ramp tips -Ramps can be moved hydraulically by approx. 235 mm outwards and approx. 365 mm inwards -Painted sand coating on the outer frame of the ramp and on the ramp tip -Flashlights on the outside of the ramp tips with switch next to the ramp controls -Ramp secured in driving position using a quick release Axles, suspension and tires: -BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle with self-steering Hodsuadk Nopfx Afnel -1st Axle with traction aid -Operation via the brake pedal in the tractor unit -Technical axle load: 12,000 kg -Air suspension with lifting and lowering valve -235/75 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 -TPMS tire pressure monitoring sensors mounted in all wheels including spare wheels Braking system: -WABCO EBS-E brand braking system in accordance with EU regulations Paintwork: -Semi-trailer MB 7350 Nova gray Accessories included: -Bulkhead made of steel, plug-in, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -JOST module B - static test load = 50,000 kg -Continuous grating with 5 mm sheet metal underlay as additional reinforcement -Painted sand coating -Cutouts in the outer frame of the loading area and the lifting bed for hanging control valves for the hydraulic ramps on the right of the vehicle -2" kingpin -Central lubrication system with 1 pump, brand BEKAMAX -On the gooseneck 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized -Electric cable winch, approx. 5,400 kg pulling force, with radio remote control -Wire cable approx. 24 m long, cable ø approx. 9.5 mm, including cable pressure roller -WABCO Smart Board System -4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Condition: used, overall weight: 47,000 kg, axle configuration: 3 axles, first registration: 11/2004, next inspection (TÜV): 08/2026, * Müller Mitteltal TS3 low loader semi-trailer Hedjw Tgkbopfx Afnsl * First registration: 11/2004 * 3 axles * Air suspension * Gigant axles * Hydraulically operated long ramps, extendable and foldable * Load width extensions from 2.50 m to 3.0 m * Loading length: 8.50 m at 0.85 m loading height * Loading length on neck: 3.40 m at 1.50 m loading height * Support legs * Unladen weight: 10,260 kg * Technical gross weight: 47,000 kg * TÜV valid until: 08/2026 * General inspection valid until: 02/2026