Low loader semitrailer

Wiese SA 36 CS-S Tieflader-Auflieger Plane,Rampe

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 11,000 kg, maximum load weight: 27,000 kg, overall weight: 38,000 kg, axle configuration: 3 axles, loading space length: 9,500 mm, loading space width: 2,480 mm, loading space height: 3,040 mm, total length: 13,800 mm, total width: 2,550 mm, total height: 4,020 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Chassis Steel welded construction with narrow crossmember spacing and reinforced design, low-loader outer frame profile, for transporting construction machinery up to 32,000 kg and with a maximum outer width of the construction machinery of 2550 mm, kingpin plate with replaceable 2 kingpins. Rear slope of approx. 1200 mm and 7°. Ramp shaft closed at the top with steel/diamond plate, in the low-bed, omega rail laterally at the bottom on the outer frame as a mounting rail for tarpaulin and spacers for lashing points, not in the wheel area. If a lift table is used, there is an additional, lightweight outer frame with an omega profile. 24-ton, 2-speed landing gear, single-sided operation, with a semi-circular lower part and a straight connection plate, with stroke compensation, free swivel radius to the rear approx.: 1950 mm, rear support, foldable 2 wheel chocks + holder Side underrun protection, aluminum Quarter panel fenders in front of and behind each axle with anti-splash flaps behind each axle Underrun protection, steel Splash flap at the rear over the entire width 4 storage boxes, stainless steel, w=800/h=350/d=350 mm, with a polished, lockable door, 2 x on the left front and 2 x on the right front in front of the 1st axle Lift table behind the gooseneck, approx. 3000 mm long, hydraulically liftable for crossing over the gooseneck, with mechanical locking in the raised position. (Cylinder angled for good ground clearance, Fliegl standard). Operation on the right front + additional activation with a wireless remote control, lift table can be raised with the tarpaulin closed! Tarpaulin attachment in the lift table area to an additional, lightweight outer frame with omega profile, lift table can be raised with the tarpaulin closed! Lashing points can also be used in the lowered position! Lashing points Gooseneck: 4 pairs of 5-ton lashing points embedded in the outer frame 2 pairs of lashing points at the top and on the side embedded in the outer frame 8 pairs of lashing points at the top and on the side embedded in the outer frame, each 10 tons 9 pairs of 5-ton lashing points embedded in the outer frame Axles + Suspension SAF drum brake axles last axle with trailing steering knuckle, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lifting and lowering valve + auto-reset function H&S function with quick vent 1st axle, automatic lift axle, incl. forced lowering and starting assist, activated by pressing the brake pedal 3 times (starting assist is functional up to an axle load exceedance of 30% and a speed of max. 25 km/h) Axle lift below the recommended ride height, no guarantee for tire damage Wheels and tires 235/75R17.5 from leading manufacturers Steel rims in twin arrangement, factory silver Braking system 2-line pneumatic braking system Spring brake parking brake 2 foolproof coupling heads at the front Kdodpfx Aei Riw Aeg Rsu EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Axle load recognition in the truck via EBS, without installation in the truck. Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white

Condition: new, empty load weight: 12,300 kg, maximum load weight: 37,200 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,480 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -Hardwood covering 30 mm thick Two-piece steel ramps: -A pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating covering -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear -Maximum load per pair: 30,000 kg Loading area: -Loading surface with rear slope of approx. 1,000 mm x 8° -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Kdodpfx Aotvfkfsg Rju Axles and tires: -BPW axles and suspension, two axles rigid, one axle self-steering -Air suspension with lifting and lowering valve The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -235/75 R17.5 3PMSF tires Accessories included: -1 Spare wheel with holder -TPMS tire pressure monitoring system according to ECE R 141 -2" kingpin -Galvanized steel bulkhead -Yellow-red air couplings on the galvanized front connecting strip -4 restraining shoes with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -3 height aluminum boards -Galvanized folding supports under the bevel of the cargo bed Height-adjustable tarpaulin superstructure (3,960 mm) -Galvanized bulkhead with a tensioning mechanism for the sliding curtain -Height-adjustable by approx. 400 mm -"EDSCHA" brand roof can be moved forwards on ALU roof rail profiles bolted to the front and rear wall -3 pairs of sliding stanchions in the loading area -The body can be hydraulically widened at the rear to the left and right by approx. 750 mm -Sliding roof with pivoting portal support -Sliding tarpaulin with 700 mm reserve in length, with tension belts at approx. 600 mm intervals -Height top edge of body approx. 3,960 mm -Driving with the sliding tarpaulin open is not permitted and will damage the tarpaulin -Cover plates to bridge the free space between ramps and loading area -Electric hydraulic unit at the rear, under the cargo bed -On the gooseneck and on the ramps on the left and right, one bracket each for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Lift axle on the front axle -Grating in the bevel of the loading area C40/4 (point load 3.4 tons on an area of 20 x 20 cm) -One INOX toolbox 565 x 290 x 810 mm in the direction of travel on the right between the axles -A layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: used, maximum load weight: 31,300 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 02/2019, loading space length: 13,600 mm, loading space width: 2,480 mm, loading space height: 3,050 mm, total width: 2,550 mm, Equipment: ABS, Meusburger MPG-3 Low-loader, flatbed with steering/lift axle, hydraulic ramp Equipment: Air suspension * Axle weighing system * 1st axle: lift axle * 3rd axle: steered * Hydraulic ramp with additional supports and remote control * Through-type ramp * Electric winch with remote control * Edscha cover * Storage boxes on both sides * Spare wheel in driving condition * Additional spotlights * Extendable overwidth signs Safety: ABS * EBS * Disc brakes Errors and prior sale excepted. Kdjdpfx Agowfwd Dj Rsu Internal vehicle number: 8303

Condition: used, maximum load weight: 44,980 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, first registration: 09/2024, next inspection (TÜV): 09/2025, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Chassis, bent * Special steel frame made of high-strength fine-grain steels, electrically welded at the joints, well-dimensioned outer frame * 4-axle arrangement. Wheel protection above the axles with spray mist suppression * All steel parts sandblasted * Lateral impact protection made of anodized aluminum mounted * Increased point load of approx. 30,000 kg over approx. 4,000 mm * Special design in the bent area for maximum low-bed length in combination with AluLeg outrigger supports instead of telescopic outrigger winches, max. rear swivel radius of the tractor unit approx. 2,100 mm Special superstructure with rear beam extension * Self-supporting aluminum roof beam / profile approx. 120 x 100 mm, sliding tarpaulin with plastic flaps * Rear beams extendable to approx. 4,200 mm * Three sliding beams per side with rubber cord relief * Additional center beam locking in the roof beam and parking position, by means of a pull cable and spring latch * Lifting roof mechanically adjustable, lifting height approx. 400 mm, can be operated on both sides or on one side, without opening the opposite side and the doors * Additional height adjustment of approx. 480 mm in approx. 40 mm increments with height adjustment in the beams * Front overhang on the front wall for operation under tarpaulin up to a total height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminum slats on the side, bottom 450 mm pockets, above 4 rows of single pockets * Only 3 rows of insert slats in the upper bed. Spacing between slats evenly distributed Floor * Approx. 27 mm special water-resistant glued beech plywood, rough surface * Steel sheet in the wheel arch area * Forklift truck accessible according to DIN standard * Outer frame flush with the surface Brakes * WABCO compressed air brake system with EBS according to EC standard 71/320 EEC including PREV (parking release safety valve) * Spring brake cylinders as parking brake * Wabco Smart Board with odometer and aggregate load indicator Axles * 4 x 10,000 kg SAF/Sauer with drum brakes in low-loader design * Air suspension with lifting and lowering device, total stroke approx. 230 mm * Third and fourth axles as friction-jointed trailing axles with electric and mechanical lock Twin tires * 235/75 R 17.5, -16-ply, incl. E-wheel holder. without E-wheel Paint finish * Chassis in RAL 3002 red, solid color * Center beams, axles coated with KTL black * Corner beams in hot-dip galvanized design * Plastic parts black Kdodjlthguspfx Ag Reu * Hot-dip galvanized parts unpainted * Rims in factory silver * Superstructure in RAL color, solid color Special equipment incl. * Air suspension in ECAS design, operated on the semi-trailer * Overwidth signs front and rear in zinc-plated, steplessly telescopic design with attached warning lights including socket for rotating beacons (small panels) * Sliding tarpaulin cover locking additionally from the outside * 4 beam adapters for special outer frame profile, to lock the center beams as desired * PVC sliding tarpaulin, color similar: RAL 9006 silver * Roof tarpaulin translucent, in overwidth and overheight design, flat hooks, tarpaulin folds, closures with pawl lock /OCS * Telescopic socket for rotating beacon including beacon on the rear left * Outer frame for machine transport with app

Condition: new, machine/vehicle number: 12853, Year of construction: 2022, operating hours: 551 h, load capacity: 10,000 kg, lifting height: 4,150 mm, free lift: 1,450 mm, construction height: 2,680 mm, fork length: 2,400 mm, front tire size: 355/50-20, rear tire size: 250-15, overall weight: 12,720 kg, Zwischenverkauf und Änderungen vorbehalten Kjdpow Arvpsfx Ag Rjdu

Condition: good (used), functionality: fully functional, empty load weight: 6,340 kg, maximum load weight: 20,660 kg, overall weight: 27,000 kg, axle configuration: 2 axles, first registration: 08/2003, next inspection (TÜV): 03/2026, loading space length: 13,600 mm, loading space width: 2,480 mm, loading space height: 2,550 mm, loading space volume: 82 m³, suspension: air, tire size: 385/65R22.5, wheelbase: 1,310 mm, ground clearance: 1,150 mm, color: blue, Year of construction: 2003, Equipment: ABS, 2-axle curtain-sided semi-trailer, French style. Inspected March 2025, valid until March 2026. Tyres at 80%. New aluminium doors. New sliding/roll-back roof tarpaulin. Disc brakes. Ksdpfxow Hm Iuo Ag Rjdu

Condition: good (used), operating hours: 4,299 h, lifting height: 3,000 mm, Manufacturer: KALMAR Type: DCE100-6 Year: 2010 Capacity: 12 t Kdedpsv D Ixdofx Ag Rou Own Weight: 16 t Lifting Height: 3 m Operating Hours: 4,299 h Equipment: Full cabin with heater, fork tine extension 2 m