Front loader forklift

Linde H 70, 7 t Stapler gut

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 11,000 kg, maximum load weight: 27,000 kg, overall weight: 38,000 kg, axle configuration: 3 axles, loading space length: 9,500 mm, loading space width: 2,480 mm, loading space height: 3,040 mm, total length: 13,800 mm, total width: 2,550 mm, total height: 4,020 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Chassis Steel welded construction with narrow crossmember spacing and reinforced design, low-loader outer frame profile, for transporting construction machinery up to 32,000 kg and with a maximum outer width of the construction machinery of 2550 mm, kingpin plate with replaceable 2 kingpins. Rear slope of approx. 1200 mm and 7°. Ramp shaft closed at the top with steel/diamond plate, in the low-bed, omega rail laterally at the bottom on the outer frame as a mounting rail for tarpaulin and spacers for lashing points, not in the wheel area. If a lift table is used, there is an additional, lightweight outer frame with an omega profile. 24-ton, 2-speed landing gear, single-sided operation, with a semi-circular lower part and a straight connection plate, with stroke compensation, free swivel radius to the rear approx.: 1950 mm, rear support, foldable 2 wheel chocks + holder Side underrun protection, aluminum Quarter panel fenders in front of and behind each axle with anti-splash flaps behind each axle Underrun protection, steel Splash flap at the rear over the entire width 4 storage boxes, stainless steel, w=800/h=350/d=350 mm, with a polished, lockable door, 2 x on the left front and 2 x on the right front in front of the 1st axle Lift table behind the gooseneck, approx. 3000 mm long, hydraulically liftable for crossing over the gooseneck, with mechanical locking in the raised position. (Cylinder angled for good ground clearance, Fliegl standard). Operation on the right front + additional activation with a wireless remote control, lift table can be raised with the tarpaulin closed! Tarpaulin attachment in the lift table area to an additional, lightweight outer frame with omega profile, lift table can be raised with the tarpaulin closed! Lashing points can also be used in the lowered position! Lashing points Gooseneck: 4 pairs of 5-ton lashing points embedded in the outer frame 2 pairs of lashing points at the top and on the side embedded in the outer frame 8 pairs of lashing points at the top and on the side embedded in the outer frame, each 10 tons 9 pairs of 5-ton lashing points embedded in the outer frame Axles + Suspension SAF drum brake axles last axle with trailing steering knuckle, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lifting and lowering valve + auto-reset function H&S function with quick vent Crsdpji Riw Ajfx Aafji 1st axle, automatic lift axle, incl. forced lowering and starting assist, activated by pressing the brake pedal 3 times (starting assist is functional up to an axle load exceedance of 30% and a speed of max. 25 km/h) Axle lift below the recommended ride height, no guarantee for tire damage Wheels and tires 235/75R17.5 from leading manufacturers Steel rims in twin arrangement, factory silver Braking system 2-line pneumatic braking system Spring brake parking brake 2 foolproof coupling heads at the front EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Axle load recognition in the truck via EBS, without installation in the truck. Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white

Condition: used, maximum load weight: 42,500 kg, overall weight: 60,000 kg, axle configuration: 3 axles, first registration: 06/2022, with 12 axles, hydraulically suspended and divided, with hydromechanical forced steering, rear taper and drive-on ramps STZ-L Gooseneck - Robust welded steel construction - Engineered loading platform 3,950 x 2,480 mm including rear taper - Hydromechanical forced steering (dual-circuit steering system) - Turntable-mounted fifth-wheel plate with interchangeable 2-inch or 3.5-inch kingpin and adjustable steering wedge - Fifth wheel load: 24 t - Rear max. steering radius: 2,600 mm Loading platform - Lowered outer sections 4,630 mm long, 420 mm deep, resulting in a loading height of 470 mm or 830 mm with floor inserts - Extendable by 2,053 mm - Includes aluminum bridging rails for creating level surfaces Crsdpfxjw Etd Ts Aafsi - Excavator boom trough at rear running gear: 4,900 mm long, 880 mm wide, 480 mm deep - Length of rear running gear: 4,900 mm incl. 500 mm rear taper, loading height 890 mm - One pair of wheel recesses in lower deck - 3-axle hydraulically suspended running gear - Split Gigant axles with 600 mm stroke Rear of vehicle - Tapered design, 500 mm - Rear hydraulic support Drive-on ramps - Two-part drive-on ramps, 2,850 + 1,850 mm long, 800 mm wide - Rubber-coated with climbing bars Braking system - Dual-line full air braking system with diaphragm brake cylinders - Automatic load-dependent brake (ALB) - Automatic slack adjusters (AGS) - Parking brake via spring-loaded cylinders - ABS brake Special equipment Radio remote control for steering and ramp operation Central lubrication system Technical data Gooseneck Loading platform (LxW): 3,950 x 2,480 mm Loaded fifth wheel height: 1,300 mm Loading platform Platform (LxW): 10,030 x 2,850 mm, extendable by 2,053 mm Lowered outer sections: 4,630 mm + 2,053 mm extension Center beam: 980 mm Excavator trough: 4,900 mm long, 880 mm wide, 480 mm deep Steering 1st to 3rd axle: hydromechanically forced steered (dual-circuit system)

Condition: new, empty load weight: 10,350 kg, maximum load weight: 39,150 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with rear slope of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood deck, 30 mm thick Loading platform: -Telescoping loading platform with rear slope of approx. 1,000 mm x 8° -1 pair of permanently installed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm -Wheel recesses with square climbing strips 15 x 15 mm and widening in the lower area -Between the 1st and 2nd axles, a pair of permanently installed wheel recesses, approx. 1,610 x 970 x 400 mm -3-part removable galvanized covers over the wheel recesses (W 670 mm) - max. point load 5 tons / piece -Recess in the slope and extending into the loading platform to accommodate the excavator arm, approx. 2,900 x 750 x 210/290 mm -1 pair of lashing rings lying at the front in the loading platform (LC 10,000 daN) -5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) -2 pairs of lashing rings that can be folded outwards (LC 10,000 daN) -2 pairs of lashing rings in the excavator arm recess (LC 5,000 daN) -Cutouts in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) One-piece aluminum ramps: -A pair of one-piece aluminum ramps, approx. 2,500 x 600 mm -Ramp with spring lift mechanism and manually adjustable Crodpfxsiu Er Ae Aafei -Maximum load per pair: 24,000 kg Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle steered -Technical axle load: 12,000 kg -Electromagnetic reversing lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -Axle tool -Tires 235/75 R 17.5 -TPMS tire pressure monitoring system according to ECE R 141 Included accessories: -One spare wheel with holder in front of the front wall -2" kingpin -One galvanized steel front wall, approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 pieces of wheel chocks with holder on the front wall -Mounting in the rear area of the gooseneck for aluminum ramps -Widening, galvanized, extendable by approx. 230 mm on each side -Galvanized folding supports under the slope of the loading platform -One mounting for a rotating beacon on the rear of the trailer -White reflector tape according to EU regulations on the side, on the extension and red at the rear -On the gooseneck and on the rear panel, one mounting each on the left and right for warning signs including socket -On the gooseneck, aluminum side and rear panels that can be plugged in, approx. 2,440 x 400 mm -The rear galvanized slotting strips are removable (length of the structure approx. 2,560 mm) -2 pairs of WADER container pockets in the loading platform for a 20ft or 30ft container -3 pairs of rung pockets for slotting strips 100 x 50 mm in the outer frame of the loading platform -One removable galvanized intermediate table with 1 pair of WADER container pockets -Square climbing strips 20 x 20 mm every 200 mm on the outer frame of the slope of the loading platform -A sand coating is applied to the diamond-patterned plates on the gooseneck and on the loading platform for slip resistance -Four warning signs, each extendable by approx. 400 mm, approx. 423 x 423 mm, with a position light -On the warning signs, a mounting for a rotating beacon -Speed sticker 80 km/h at the rear and on both sides -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel structure shot blasted, then the defined visible sur

Condition: new, maximum load weight: 36,410 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Extract from the equipment. Full equipment details available on request. GOOSENECK: Cjdey Auh Iepfx Aafori * Gooseneck in SNT design for optimized loading platform length, length approx. 3,700 mm, rear with taper approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Steel front wall, removable, approx. 400 mm high * ASPÖCK-UNIBOX * 3 kW electro-hydraulic power unit for hydraulic functions, excluding hydraulic winches * Approx. 40 mm thick hardwood decking above the gooseneck * 2-inch kingpin * Gooseneck guide plate for the fifth-wheel plate, approx. 500 mm wide * Bracket at the rear of the gooseneck for ALU loading ramps * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 4 wheel chocks with holders in front of the front wall * 1 pair of stake pockets recessed on the gooseneck for plug-in stakes approx. 100 x 50 mm (located on the inside of the chassis rail) EQUIPMENT: * Loading platform length approx. 8,800 mm, extendable version approx. 4,100 mm, with rear taper approx. 500 mm x 10° * A recess in the loading platform, extending into the tapered section to accommodate the excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * Pneumatic locking with conical locking bolts and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adapt to the selected loading platform length * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steered * 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: each 12,000 kg with air suspension and raise/lower valve * 235/75 R 17.5 3PMSF twin tires. Manufacturer at our discretion * Mechanical landing legs with 2-speed gearbox and crank. JOST Module B – static test load = approx. 50,000 kg * Throughout the loading platform and between the axles, interrupted approx. 50 mm thick hardwood decking (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the telescopic tube with large cross-section. Intermediate table with offset loading platform and extendable mounting rails for aluminum bridging elements * Platform locking with conically welded locking profiles every approx. 250 mm. Includes pre-tensioning plate * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards (LC 10,000 daN) * 1 pair of fixed wheel recesses in front of the axles, open up to the gooseneck cross member, approx. 700 x 410 mm (W x D) * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom (in case vehicle is equipped with extendable widenings) * 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the platform between 1st and 2nd axle * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom * Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axle, which can also be used as widening planks (if vehicle is equipped with extendable widenings) * Lockable aluminum elements installed on the extension tubes of the widenings * 1 pair of mechanical rear supports * 1st axle with traction aid * Sandblasting painted...

Condition: new, maximum load weight: 37,619 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 9,240 mm, loading space width: 2,550 mm, total width: 2,550 mm, total height: 3,570 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer K.SLS 3 / 0N ? 18/30 | Year of Manufacture 2025 | NEW | 40t Ramps | Top Specification Location: Germany Condition: New / Unused Availability: Immediately --- Description For sale is a brand-new Kässbohrer K.SLS 3 / 0N ? 18/30 low-loader, year of manufacture 2025. Perfect for transporting construction machinery, equipment, and heavy goods. Robust chassis, high-quality axles, heavy-duty ramps — ready for immediate use. --- Technical Data Dimensions: - Overall length: 13,190 mm - Platform length: 9,240 mm - Platform height: 875 mm - Overall width: 2,550 mm (+600 mm with side extensions) - Gooseneck length: 3,950 mm - Unladen weight: approx. 10,381 kg Weights: - Permissible gross weight at 80 km/h: 48,000 kg - Permissible gross weight at 60 km/h: 52,800 kg - Total axle load: 30,000 kg - Kingpin load: up to 18,000 kg --- Chassis & Axles: - 3 BPW axles, air suspension, drum brakes - 1 trailing axle at rear - Lift axle (load-dependent + automatic control from the cab) - Tyres: 245/70 R17.5, M+S + 3PMSF - Tyre pressure monitoring R141 Crsdpfxox Efzus Aafji - Wabco EBS 4S/3M, ABS + RSS - Wabco Smartboard (axle load, suspension, diagnostics, etc.) --- Ramps & Loading Area: - Foldable 40t access ramps - Ramp length: 2,750 mm - Ramp width: 850 mm - Hydraulic sliding system - 45 mm hardwood floor + chequer plate over wheel arches --- Load Securing: - Multiple 8,000 daN and 13,400 daN lashing points - 7×2 stake pockets + plug-in stakes - Container locks for 1×20 ft - 450 mm front wall, side and rear walls made of aluminium --- Body & Chassis: - High-strength S700 MC steel - Partially metallised (Zn/Al 85/15) — strong corrosion protection - Rear angle: 10°, 500 mm - 2" kingpin - Mechanical landing legs at front - 45t supports at rear --- Equipment: - 2× toolboxes - All-round warning beacon - LED lighting - Rear work lights - Wheel chocks - 9×2 extensions (up to +300 mm) - Stake box - Reflective strips on sides & rear --- Colour: RAL 3020 Traffic Red We are happy to provide further information upon request.

Condition: used, overall weight: 42,000 kg, axle configuration: > 3 axles, first registration: 02/2013, total width: 2,550 mm, total height: 4,000 mm, Year of construction: 2013, Manufacturer: Faymonville Type: STN-3UB Cedps Agqqkefx Aafjri Year of manufacture: 2013 Product type: Used Data: Initial registration: 13.02.2013 Number of axles: 3 Overall dimensions L x W x H: 13.50 x 2.55 x 4.00 m Unladen weight: 10,900 kg Permissible total weight: 42,000 kg Special features: Semi-trailer, standard low-loader, axle with trailing swivel The vehicle may only be operated behind a towing vehicle with a plug connection according to ISO 7638 (5- or 7-pole). Location: 45143 Essen Note: immediately available

Condition: used, mileage: 370,731 km, power: 355 kW (482.67 HP), first registration: 10/2023, fuel type: diesel, overall weight: 19,500 kg, axle configuration: 2 axles, brakes: retarder, color: white, gearing type: automatic, Equipment: ABS, air conditioning, electronic stability program (ESP), parking heater, soot filter, Model year * Model year: 2023 Transmission * TraXon automatic transmission, 12 gears Assistance systems * Electronic Braking System (EBS) * Adaptive Cruise Control (ACC) * Lane Keeping Assist * Hill Start Assist * Turning Assist Lights and Visibility * LED headlights * Cornering lights * Fog lights * Ambient lighting * Turning lights Audio & Communication * Radio with MP3 * Digital Radio (DAB) * Sound system * Information and service system Exterior * Air suspension * Fifth wheel coupling * Sunroof * Electrically adjustable exterior mirrors * Differential lock * Work lights * 1x15-pin connector * Full fairing * Upper and lower bunk Safety * Intarder * Electronic Stability Program (ESP) * Anti-lock Braking System (ABS) * Curb mirror * Wide-angle mirror * Tire pressure monitoring system Interior * Fabric seats Cjdpe Af Dd Sefx Aafjri * Digital tachograph * Multifunction steering wheel * On-board computer * Sun visor * Cooler box Comfort * Air conditioning * Auxiliary heater * Air-suspended driver/passenger seat * Heated driver's seat * Power steering * Adjustable steering column * Electrically operated windows * Central locking * Cup holder * Digital instrument cluster * Suspended cab Tire dimensions * 1st axle: 315/70 R22.5 * 2nd axle: 315/70 R22.5 Other dimensions and weights * Payload: 11,125 kg * Permissible total weight: 19,500 kg * Fuel tank: 1,195 liters * AdBlue tank: 85 liters * Wheelbase: 4,000 mm ----Vehicle location: 90518 Altdorf. Errors and omissions excepted.