Used Hangler Semitrailers for sale (10)

Condition: used, overall weight: 41,000 kg, maximum load weight: 30,480 kg, axle configuration: 3 axles, loading space length: 17,270 mm, loading space width: 2,550 mm, loading space height: 850 mm, first registration: 03/2023, next inspection (TÜV): 03/2026, Year of construction: 2023, total width: 2,550 mm, total height: 850 mm, Equipment: ABS, HANGLER 3-axle semi-low loader, telescopic, type SDS-H 470 First registered 03/2023, in mint condition Empty weight only 10,520 kg Loading height unloaded approx. 850 mm Fifth wheel height 1,050 to 1,100 mm Gooseneck length 3,650 mm Low bed length 9,770 mm, extendable by 7,500 mm = total low bed length 17,270 mm, movable intermediate support on the telescope Extra-wide package up to a width of 3,000 mm, extendable frame extensions including wooden supports, frame bevel at the rear 8° Continuous U-profile hanging rail for docking ramps Front support feet telescopic Rear support telescopic 4 pairs of container locks recessed in the floor for 1x 40 ft. or 2x 20 ft. containers Kslhccqeu Dftvjpsdn 9 pairs of stake pockets embedded in the outer frame 2 stake bushing strips, continuous across the width Plastic tool box Ramp storage box 11 pairs of folding lashing rings, each 10,000 daN, freely pivoting in the side frame profile (also suitable for over-width lashing) 11 pairs of lashing holes in the outer frame on the gooseneck (tension belt attachment) 13-fold tires 235/75 R 17.5 SAF axles with drum brakes Air suspension with raising/lowering Offset axle spacing 1,360/1,410 mm 3rd axle TRAILING STEERING WABCO Trailer-EBS with RSS driving stability system Chassis frame front spray galvanized + final coat in RAL 3002 Chassis rear hot-dip galvanized + outer frame visible area finished with RAL 3002 RENTING is the new BUYING, also available immediately for full-service rental-----

Condition: used, color: red, Year of construction: 2014, Hangler 3 STZL 30. Year: 2014. 9 tons BPW axles. Weight: 12,650 kg. Max weight: 35,000 - 41,000 kg. Kingpin load: 11,000 kg. Hydraulic works on NATO from the truck. 1st axle liftaxle. 2nd and 3rd axles steering axles Powersteering. Hydraulic bridge from floor to neck (lenght: 2300 mm). Slitted floor. 2 x 25 cm widened. Winch. Allu boards on gooseneck. Airsuspension. 2 point hydraulic outriggers on the back. 2 way hydraulic ramps. Hydraulic from left to right. Dimmensions: Neck: L: 4250 mm. W: 2550 mm. H: 1360 mm. Kingpin height: 1150 mm. Floor: L: 9530 mm. W: 2550 mm. H: 950 mm. Tyres: 235/75R17.5 80%. 2 Pieces avialable! ID NR: 650. The General Terms and Conditions of Heinhuis are applicable to all adverts, offers and quotations by Heinhuis, all agreements entered into by Heinhuis and the negotiations preceding them. By any form of response you accept the applicability of the General Terms and Conditions of Heinhuis and you declare that you have taken note of these General Terms and Conditions. Our prices are export net prices. = Further information = Year of construction: 2014 Unladen weight: 12,650 kg Payload: 28,350 kg GVW: 41,000 kg = Company information = For more information: Kslhccqowm Icaepsdn WhatsApp:

Condition: good (used), overall weight: 34,500 kg, Year of construction: 2009, Manufacturer: Hangler Type: 3STZL24 Year of manufacture: 2009 Own weight: 7960 kg Payload: 26,540 kg Total weight: 34,500 kg Length to: 13,900 m Kelhsvwz Ursccqpsdn

Condition: used, overall weight: 58,000 kg, maximum load weight: 47,580 kg, axle configuration: > 3 axles, loading space length: 1,300 mm, loading space width: 3,000 mm, loading space height: 890 mm, first registration: 04/2021, Year of construction: 2021, total width: 2,550 mm, total height: 3,900 mm, Equipment: ABS, Hangler SVS-H 580 4 Achs Semie Tieflader Erstzulassung:27-04-2021 SAF Achsen Liftachse 2x Nachlauf Lenckachsen Drum brakes with ABS and EBS Reifen:235/75 R17.5 Approx.40% Kdjlhccowapm Tjqpsn Luftfederung Total weight: 58,000 kg, Leather weight: 10,420 kg, Nutzload: 51,760 kg. Schwaneneck Length: 4.00 Mtr., Tiefbedlänge: 9.00 Mtr., Width: 2.55 Mtr. + 2x25 Cm. Drawer height: 89 cm. Hydraulic Ramps:350 Cm. Rampen Hydraulic In Breite Verstellbar 2 Stutzen Hinten Smart board 24 Volt Powerpack Fuer Rampen Irrtümer / Schreibfehler und Zwischenverkauf Vorbehalten

Condition: used, overall weight: 33,000 kg, empty load weight: 7,170 kg, maximum load weight: 25,830 kg, axle configuration: 3 axles, first registration: 01/2007, tire size: 455/40 r22,5, machine/vehicle number: 8c9a877b63be8509f58298a74, Further information 2 VEHICLES AVAILABLE! - 2 VEHICLES AVAILABLE! - 2 VEHICLES AVAILABLE! - 2 VEHICLES AVAILABLE! Kelhoi Ri Akjccqpedn Air suspension with lifting and lowering, BPW disc brake axles, 2-speed gearbox door winches with thrust compensation, 1 plastic storage box, sliding roof, side tarpaulin, 2-leaf portal doors, spare wheel holder without wheel, hazardous goods plate, A-plate, document roll, customs cord, 4 rows of aluminum slats, coil trough approx. 7,000 mm long, 2 bumpers at the rear, warning signs according to ECE-070, tyres approx. 30 - 40 % 2 VEHICLES AVAILABLE! - 2 VEHICLES AVAILABLE! - 2 VEHICLES AVAILABLE! - 2 VEHICLES AVAILABLE!

Condition: used, overall weight: 18,000 kg, maximum load weight: 13,830 kg, axle configuration: 2 axles, first registration: 02/2012, Year of construction: 2012, Equipment: ABS, Trailer HANGLER 2 PEL 18 2 axle Pritscge tarpaulin, dropside with stanchion holders Kdslhstrur Ajccqpon 4170Kg tare weight 13830Kg Payload Condition: TOP Tires: 70-90%

Condition: used, color: red, Year of construction: 2014, Hangler 3 STZL 30. Year: 2014. 9 tons BPW axles. Weight: 12,650 kg. Max weight: 35,000 - 41,000 kg. Kingpin load: 11,000 kg. Hydraulic from trailer works on NATO. 1st axle liftaxle. 2nd and 3rd axles steering axles (power steering). Hydraulic bridge from floor to neck (length: 2300 mm). Slitted floor. 2 x 25 cm widened. Wink. Air suspension. Allu boards on neck. 2 point hydraulic outriggers on the back. 2 way hydraulic ramps. - hydraulically slid from left to right. Dimensions: Neck: L: 4250mm. W: 2550mm. H: 1360mm. King pin height: 1150 mm. Floor: L: 9530mm. W: 2550mm. H: 950mm. Radio Remote Control! Tires: 235/75R17.5 40%. Kslhcswl Ev Uocqpjdn ID NO: 651. The General Terms and Conditions of Heinhuis are applicable to all adverts, offers and quotations by Heinhuis, all agreements entered into by Heinhuis and the negotiations preceding them. By any form of response you accept the applicability of the General Terms and Conditions of Heinhuis and you declare that you have taken note of these General Terms and Conditions. Our prices are export net prices. = Further information = Year of construction: 2014 Curb weight: 12,650 kg Payload: 28,350 kg GVW: 41,000 kg = Company information = For more information: WhatsApp:

Condition: new, overall weight: 35 kg, empty load weight: 8 kg, maximum load weight: 26 kg, axle configuration: 3 axles, tire size: 435/50 r 19,5, machine/vehicle number: cd0062ee491e6794168ccb01a, Further information Chassis semi-trailer In proven HANGLER welded construction made of high-quality steel with UP-welded side members tapered towards the front. Frame neck height 120 mm, with double center bar. Z-profile cross members punched through on the side member with floor panels (larger spacing) and with welded special side frame.2 kingpins to DIN 74080, replaceable, with grinding plate beveled to the front, made of high-quality sheet steel. EC front turning radius 2,040 mm. Sliding plate continuously welded from saddle plate to front plate *inside* 18 pairs of lashing eyes embedded in the outer frame, 2.5 tons each 8 pairs of lashing eyes embedded in the outer frame, 5 tons each 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminum side collision protection Plastic mudguards with splash protection mats Underride guard Impact protection at the rear Spare wheel holder for 1 e-wheel, with wheel mounting kit 3 Plastic tool box, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) Aluminum ladder 3 300 mm, loose Pair of recessed stanchion pockets Piece of stanchions Storage compartment for plug-in slats on one side in FR left, below loading area Storage compartment for drop sides underneath the cargo bed, open, if technically possible Coil trough/inclined loading device Coil trough 8,000 mm long with cover and rubber pad. Cover 35 mm. With inclined loading bars and supports suitable for FR 80/80/4, complete stanchions 80/80 incl. lower reinforcement supplied Hydraulic sloping loading device with 4 crossbars:Hydraulic supply via tractor unit by means of 2-pipe pump system (forward/return) with 2-fold Faster coupling mounted on bulkhead (hoses are connected to Faster coupling from below).Sloping loading bars (FR 180x100x8 mm) with integrated extension part can be locked in height. Multi-stage hydraulic cylinders, each beam with cardanic suspension Incl. outriggers - adjustable - with bolt safety device underneath the loading area5-fold control block for operating the sloping loading device and for folding device sliding roof.1 set of boiler floor holder with height-adjustable support bolts for different boiler floor diameters, incl. shelf.1 piece of stop protection for sloping plate - for securing to the front! Axles + suspension SAF disc brake axles Offset axle spacing mm Air suspension Brake system 2-line compressed air brake system Aluminum air reservoir Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS make Wabco, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lift & lower valve + auto-reset function Vehicle - driving stability system Wheels and tires 435/50 R 19.5, manufacturer's choice Factory silver steel rims, manufacturer's choice Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1 additional LED work light(s) at the rear, switched via reversing light 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm, detachable with plug 1 rotating beacon with holder, detachable Floor Kdslhcei Riw Hscqpsn Screen printing plates approx. 3

Condition: new, empty load weight: 4,100 kg, machine/vehicle number: 087c7b6bc0c6118a84279fb46, Further information Frame Welded steel construction made of fine-grained steel, hot-dip galvanized, flat plateau without raised edges, Loading area slanted downwards by approx. 8° after the rear axle. Side members made of steel profiles, Hot-dip galvanized steel frame, with stainless steel plate at the kink as cable guide - flush with the floor. For trucks with Wheelbase: 2nd axle 5,100 mm / 2nd to 3rd axle 1350 mm Trailer coupling Towing hitch ball head D24.8: (height from floor to top edge approx. 480 mm), towing capacity 2,800 kg, incl. assembly and electrics with 7-pin socket Accessories/conversions 2 holders for wheel chocks, aluminum side bumpers, foldable - are taken from the truck! Steel underride guard, quarter-shell mudguards with mud flaps - will be taken from the truck! Storage box Plastic tool box, with drawer and shelf, w=650 Incl. / h=520 / d=670 mm, lockable with a padlock (lock not included). not included) 1 holder for 3 pcs. petrol cans 1 stainless steel storage box, w=600/h=400/t=500 mm, with polished door, incl. lockable, includes control valve. lockable, includes control valve and electro-hydraulic pump unit. pump unit. Control box with circumferential door seal and sealing sleeves on the back (splash-proof according to techn. technical possibility) Kdolhsi Riytsccqpon Electrics Adaptation of the existing rear lights, 2 additional LED work lights, recessed in the bulkhead recessed switched via parking light with switch on front wall outside in FR-left, 1 LED work light, at the rear, with integrated reversing camera Incl. with color flat screen monitor, screen with suction cup mount and power supply via 24 volts, Voltage divider 24/12V, 1 socket 7-pin 12V = plug-in adapter Base Mega Grip made of toothed galvanized grating, steel grating 50/4 Incl. with mesh width 50 mm. Top side with anti-slip serration, laid continuously over the entire main frame plateau Lashing eyes 12 pairs of lashing rings suspended freely pivoting in the outer frame - 10 tons each. 1 x at the front and the last one at the rear. 1 piece Lashing eyelet at the very rear in the center for fastening the winch cable 12 lashing eyes centrally embedded in the floor, 5 tons each, (not included in Incl. rear sloping) Front wall Sheet steel bulkhead, height 1,500 mm. Fixed with corner pillars at front wall height. In each case 2 x 12 pcs. Suspension brackets for lashing chains mounted on the left and right of the front wall Cable winch Electric cable winch, 24 volt, pulling force approx. 6350 kg, mounted in the center of the bulkhead (recessed with loading bridge), operation with radio remote control, cable length min. 35 m x 9.5 mm, with roller rope window, with cable pressure plate, incl. overload protection, cable freewheel clutch, manual switch with approx. 5 m control lever, acceptance of the cable winch, civil engineer test report, test book, operating instructions Drive-on ramps Length 3,500 mm - 2-part (2,000 mm + 1,500 mm), width 850 mm, load capacity 20,000 kg / pair (also for ramp loading), electric for ramp loading), electro-hydraulically foldable and laterally movable - incl. Electro-hydraulic pump unit. Drive-on angle approx. 8° with lowered rear axle Ramp support made of hot-dip galvanized steel grating (like the floor of the loading bridge), with with anti-skid toothing. Ramps can be pushed together to approx. 170 mm, Hydraulic ramp extension. Ramp prepared for operation on loading ramp with full load capacity. Ramp locking with 2 tension belts. Ramp tip offs

Condition: new, empty load weight: 4,600 kg, machine/vehicle number: c78894767223a51dd199030f3, Further information Frame Welded steel construction made of fine-grained steel, hot-dip galvanized, flat plateau without raised edges, Loading area slanted downwards by approx. 8° after the rear axle. Side members made of steel profiles, Hot-dip galvanized steel frame, with stainless steel plate at the kink as cable guide - flush with the floor. For trucks with Wheelbase: 2nd axle 1,795 mm / 2nd to 3rd axle 4105 mm and 3rd to 4th axle 1350 mm Trailer coupling Towing hitch ball head D24.8: (height from floor to top edge approx. 480 mm), towing capacity 2,800 kg, incl. assembly and electrics with 7-pin socket Accessories/conversions 2 holders for wheel chocks, aluminum side bumpers, foldable - are taken from the truck! Steel underride guard, quarter-shell mudguards with mud flaps - will be taken from the truck! Storage box Plastic tool box, with drawer and shelf, w=650 Incl. / h=520 / d=670 mm, lockable with a padlock (lock not included). not included) 1 holder for 3 pcs. petrol cans 1 stainless steel storage box, w=600/h=400/t=500 mm, with polished door, incl. lockable, includes control valve. lockable, includes control valve and electro-hydraulic pump unit. pump unit. Control box with circumferential door seal and sealing sleeves on the back (splash-proof according to techn. technical possibility) Electrics Adaptation of the existing rear lights, 2 additional LED work lights, recessed in the bulkhead recessed switched via parking light with switch on front wall outside in FR-left, 1 LED work light, at the rear, with integrated reversing camera Incl. with color flat screen monitor, screen with suction cup mount and power supply via 24 volts, Voltage divider 24/12V, 1 socket 7-pin 12V = plug-in adapter Base Mega Grip made of toothed galvanized grating, steel grating 50/4 Incl. with mesh width 50 mm. Top side with anti-slip serration, laid continuously over the entire main frame plateau Lashing eyes 12 pairs of lashing rings suspended freely pivoting in the outer frame - 10 tons each. 1 x at the front and the last one at the rear. 1 piece Lashing eyelet at the very rear in the middle for fastening the winch cable 12 lashing eyes centrally embedded in the floor, each 5 to. (not included in Inkl. rear slope) Front wall Sheet steel bulkhead, height 1,500 mm. Fixed with corner pillars at front wall height. Each with 2 Kdelhcjk Unitocqpen x 12 pcs. Suspension brackets for lashing chains mounted on the left and right of the front wall Cable winch Electric cable winch, 24 volt, pulling force approx. 6350 kg, mounted in the center of the bulkhead (recessed with loading bridge), operation with radio remote control, cable length min. 35 m x 9.5 mm, with roller rope window, with cable pressure plate, incl. overload protection, cable freewheel clutch, manual switch with approx. 5 m control lever, acceptance of the cable winch, civil engineer test report, test book, operating instructions Drive-on ramps Length 3,500 mm - 2-part (2,000 mm + 1,500 mm), width 850 mm, load capacity 20,000 kg / pair (also for ramp loading), electric for ramp loading), electro-hydraulically foldable and laterally movable - incl. Electro-hydraulic pump unit. Drive-on angle approx. 8° with lowered rear axle Ramp support made of hot-dip galvanized steel grating (like the floor of the loading bridge), with with anti-skid toothing. Ramps can be pushed together to approx. 170 mm, Hydraulic ramp extension. Ramp prepared for operation on loading ramp with full load capacity. Ramp locking with 2 tension