Other

Hoeflon C4e Minikran

Condition: used, Year of construction: 2024, operating hours: 10 h, Equipment: all wheel drive, Hoeflon Mini Crane C4e - demonstration device Multifunctional compact crane First registered: May 16, 2024 Capacity: 2350 kg Max. swivel range: 11.7 m x 144 kg Max. lifting height including options 15.1 m Dimensions L x W x H: 2.8 m x 0.75 m x 1.82 m Dimensions including cable winch and boom: 3.04 m x 0.75 m x 1.95 m Total weight: 1,900 kg and with options 2,150 kg Mast system: cylinder and chain system Boom angle: -5 - 83 degrees Swivel: 360 degrees Drive system: with remote control 1st gear: 1.2 km/h 2nd gear: 2.4 km/h Hnsdpfx Afotrh T Es Seh Engine: Yanmar 3 cylinders, 1500 rpm Inclination angle: 20 degrees Ground pressure: 0.59kg/cm2 Special equipment included: Fly-Jib Cable winch: 3000 kg Extension part adjustable by 30° Supports can be bent

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2025, 3-axle MULTIMAX *PLUS semi-trailer low loader, air-suspended and hydraulically forced steered axles. Technical data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h Legal Total weight: 49500 kg 31500 kg Fifth wheel load: 18000 kg Axle load: 31500 kg 31500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm King pin turning radius to the rear approx.: 2,100 mm Fifth wheel height when loaded approx.: 1,205 mm Loading area length approx.: 9,600 mm Extendable by approx.: * Loading area width approx.: 2,540 mm Loading height with max. load approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle distance: 1,360 mm *Total weight depends on the fifth wheel load: Yes Special permit required if the country-specific legislation is exceeded: Technical description Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,900 mm, with a bevel at the rear approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor units: 4 x 2 and 6 x 2. Loading area: Loading area, length approx. 9,600 mm with a bevel at the rear approx. 900 mm x 6°. Loading area can be raised and lowered hydraulically after the gooseneck, length approx. 3,000 mm, load capacity up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS A pair of two-part AXS steel ramps with a length of approx. 4920 mm and a width of approx. 900 mm. Open grating surface. Ramp tips that can be opened hydraulically. Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 365 mm inwards. Maximum load and ramp angle according to technical data sheet: C470319 Maximum incline angle with lowered loading area: 9° Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced steered. Technical axle load: 12,000 kg Air suspension with lifting and lowering valve. Axle tool. Tires: 235/75 R 17.5 3PMSF twin tires. Make of our choice Load index 143/141J (144/144F) Brake system: WABCO EBS-E brake system in accordance with EU regulations. Without connection cable to the tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Version in accordance with EU regulations. (ASS 3) Metallization Complete HRM metallization (High Resistance Metallization) Complete steel construction shot blasted, then hot-finished with ZINACOR 850 (zinc 85% - aluminum 15%). Paint 6-K final treatment: Complete steel construction shot blasted after welding. 1 layer of zinc-based base paint, 1 layer of adhesion primer. Final painting with 2 layers of 2-component paint (acrylic) in a single color in RAL colors of your choice, then sealing the cavities with special wax. Hodpsizu Ntofx Af Sonh Rims in silver. Multi-color and special painting for an additional charge. Steel construction: Steel construction made of high-strength fine-grain steel. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welder tested according to DIN-EN 287-1. MAG welding process according to EN ISO 4063. Protective gas M21 according to EN ISO 14175 iFront wall made of steel, pluggable, approx. 400 mm high Connection strip for supply lines to the SZM, attached at the height of the outer frame profile. i ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets 24N connection in accordance with ISO-1185 24S connection in accordance with ISO-3731 15-pin connection in accordance with ISO-12098 If your pin assignment differs from the ISO connection standard, please let us know. i "Anderson"

Condition: new, empty load weight: 10,350 kg, maximum load weight: 39,150 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area: -telescopic loading area with rear slope approx. 1,000 mm x 8° -1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm -Wheel recesses with square climbing strips 15 x 15 mm and widenings in the lower area -A pair of fixed wheel recesses between the 1st and 2nd axles, approx. 1,610 x 970 x 400 mm -3-piece removable galvanized covers over the wheel recesses (W 670 mm) - max. point load 5 to / pc. -Recess in the chamfer and protruding into the loading area to accommodate the excavator dipper stick approx. 2,900 x 750 x 210/290 mm -1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) -5 pairs of lashing rings foldable outwards (LC 5,000 daN) -2 pairs of lashing rings can be folded outwards (LC 10,000 daN) -2 pairs of lashing rings in the excavator trough (LC 5,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) One-piece ALU ramps: -One pair of one-piece ALU ramps approx. 2,500 x 600 mm -Ramp with spring lifting mechanism and manually adjustable -Maximum load per pair: 24,000 kg Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 tires -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin Hnedjiu Er Aopfx Af Ssh -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking lights -Galvanized extensions, extendable by approx. 230 mm per side -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon at the rear of the trailer -White reflector tape in accordance with EU regulations on the sides, on the pull-out and red at the rear -One bracket for the warning signs including socket on the left and right of the gooseneck and on the rear panel -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container -3 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -One removable galvanized intermediate table with 1 pair of WADER container pockets -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -a layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -A bracket for a rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: used, Year of construction: 2024, operating hours: 10 h, Equipment: all wheel drive, Hoeflon C6 Mini Crane - Demo Unit First registered: April 30, 2024 Capacity: 3000 kg Max. slewing range: 13.70 m x 210 kg Max. lifting height: 11.5 m and 16.40 m including options Dimensions L x W x H: 2.98 m x 0.77 m x 1.88 m Dimensions including winch and boom: 3.20 m x 0.77 m x 2.00 m Total weight: 2850 kg Mast system: Cylinder and chain system Boom angle: -5 - 83 degrees Slewing: 360 degrees Speed: 2.2 km/h Engine: YANMAR 3-cylinder, 7.3 kW (diesel), 1,500 rpm Electric drive: 230V Starter: Electric start via remote control Fuel / Tank capacity: Diesel / 20 l Hnedji N U Dcopfx Af Seh Tilt angle: 15 degrees Ground pressure: 0.79 kg/cm2 Included special options: Fly jib Extension section adjustable by 30° Foldable outriggers Cable winch: 3,000 kg Would you like another demonstration of a Hoeflon mini crane? No problem, we'll come to your desired location and present the Hoeflon mini crane to you.

Condition: new, Equipment: all wheel drive, Hoeflon mini crane C6e - new device Powerful all-rounder available from stock. Capacity: 3000 kg Max. Swivel range: 13.70 m x 210 kg Hnsdpfxot Il Dbj Af Soh Lifting height max. 11.5 m and incl. options 16.40 m Dimensions L x W x H: 2.98m x 0.77m x 1.88m Dimensions incl. cable winch and boom: 3.20 m x 0.77 m x 2.00 m Total weight: 2850 kg Mast system: cylinder and chain system Boom angle: -5 - 83 degrees Pivoting: 360 degrees Speed: 2.2 km/h Motor/battery: OX Power accu Tilt angle: 15 degrees Ground pressure: 0.79 kg/cm2 Special options included: Fly-Jib Extension part 30°adjustable Foldable outriggers Cable winch : 3,000 kg

Condition: new, overall weight: 41,000 kg, axle configuration: 3 axles, loading space length: 12,360 mm, total width: 2,550 mm, total height: 1,800 mm, Year of construction: 2021, Equipment: ABS, Swap chassis trailer for 40', 2x 20', 1x 30', 1x 40'HC container * Lift axle * Rear pneumatically extendable by 1360 mm * SAF axles with disc brakes * Jost landing legs * Wabco Trailer EBS-E, ABS * Haldex Colas air system * Wheel chocks Hnodpfx Askc T Ngsf Seh ----Vehicle number 6945 -----Errors and interim sale excepted WhatsApp support available! If you have questions about the vehicle or need more information, feel free to contact us via WhatsApp Whatsapp Whatsapp

Condition: new, Year of construction: 2024, Hoeflon Mini Crane C10e – New machine The powerful all-rounder Delivery time: on request Capacity: 4000 kg Max. swing range: 13.70 m x 500 kg – incl. options: 19.80 m x 209 kg Max. lifting height: 16.30 m incl. options: 22.00 m Dimensions L x W x H: 3.93 m x 0.80 m x 1.97 m Dimensions incl. winch and boom: 4.15 m x 0.80 m x 2.07 m Total weight: 4400 kg, incl. options 4700 kg Weight of boom arm: 205 kg Boom angle: 5 - 83 degrees Slewing: 360 degrees Drive system with remote control: 1st gear: 1.1 km/h 2nd gear: 2.3 km/h 3rd gear: 2.9 km/h Hjdpjrbdh Esfx Af Sonh Electric drive: 400 V Tilt angle: 20 degrees optional special equipment: Fly-Jib Extension part, 30° adjustable Winch: 4000 kg Color of choice

Condition: new, Year of construction: 2023, Equipment: all wheel drive, Haulotte Compact 10DX - New device Delivery time: on request Color: Haulotte Standard (RAL1006) Delivery to your desired address is possible. Working height 10.28 m Platform height 8.28 m Maximum load capacity 565 kg Platform length 2.45 m Platform length with extension 3.7 m Platform extension 1.2 m Platform width 1.45 m Transport height 1.59 m Height when retracted 2.44 m Width 1.78 m Length 3.17 m Wheelbase 1.84 m Standard equipment: * All-wheel drive, steerable front wheels Hnodpfx Aomv Natof Soh * Drive motor disengagement * Foam-filled tires for all terrains * One-sided platform extension 1.2 m * Removable control panel on the platform * 3° inclinometer * Automatic leveling of the outriggers * Horn * Operating hours counter * Batteries 12 V ? 74 Ah * Hydraulic brakes * Manual emergency lowering * Lifting eyes for fall protection * Towing and crane eyes * Side protection Additional options: * Non-marking tires * Socket on the work platform * Swing door * Hydr. generator 3.5 kW * Biodegradable hydraulic oil * Kit for cold countries * Preparation for tracking* * Acoustic driving signal * Warning signal when driving * Rotating beacon * Working lights * Fold-down railing * Optional color (RAL) *Only available ex works, cannot be retrofitted to stock machines. 24-month manufacturer's warranty on wages and spare parts.