Work platform

HAULOTTE Compact 10 DX

Condition: used, machine/vehicle number: 2163874, fuel type: diesel, Year of manufacture: 2026 Unladen weight: 3,350 kg Lifting capacity: 565 kg Working height: 1,028 cm Dimensions of the loading area: 318 x 178 x 244 cm Condition of front tires: 0 Condition of rear tires: 0 Cedpfozq Rcbox Aafsri Please contact PFEIFER GROUP for further information.

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, 3-Axle MULTIMAX "PLUS" semi-trailer, air-suspended and with hydraulically forced steering axles. Technical data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h (legal) Total weight: 49500 kg / 31500 kg Fifth wheel load: 18000 kg Axle load: 31500 kg / 31500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Kingpin offset to rear approx.: 2,100 mm Fifth wheel height loaded approx.: 1205 mm Platform length approx.: 9,600 mm Extendable by approx.: ? Platform width approx.: 2,540 mm Loading height at max. load approx.: 890 mm Suspension travel approx.: -55 / +145 mm Axle spacing: 1,360 mm Total weight dependent on fifth wheel load: Yes Special permit required if exceeding country-specific regulations. Technical description Codpfxjizu Nte Aafsri Gooseneck: Gooseneck in SNT design to optimize platform length, length approx. 3,900 mm, rear with a bevel of approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor-trailer combinations: 4 x 2 and 6 x 2. Platform: Platform, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6°. Platform behind the gooseneck can be hydraulically raised and lowered, length approx. 3,000 mm, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS A pair of two-piece AXS steel ramps with a length of approx. 4,920 mm and a width of approx. 900 mm. Open grating deck. Hydraulically folding ramp ends. Ramps can be individually hydraulically shifted outwards by approx. 235 mm and inwards by approx. 365 mm. Maximum load and angle of inclination according to technical data sheet: C470319 Maximum inclination angle with lowered platform: 9° Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced steered. Technical axle load: 12,000 kg Air suspension with lifting and lowering valve. Axle tool. Tires: 235/75 R 17.5 3PMSF, twin tires. Manufacturer according to our choice Load index 143/141J (144/144F) Braking system: Braking system of the brand WABCO EBS-E according to EU regulations. Without connection cable to the tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" design according to EU regulations. (ASS 3) Metallization: Complete HRM metallization (High Resistance Metallization) Complete steel structure shot-blasted, then hot-dip galvanized with ZINACOR 850 (Zinc 85% - Aluminum 15%). Painting: 6-coat finish: Complete steel structure shot-blasted after welding. 1 coat of zinc-based primer, 1 coat of adhesion primer. Top coat with 2 coats of 2-component paint (acrylic), solid color in RAL colors of your choice, followed by sealing of the cavities with special wax. Rims in silver. Multi-color and special paint finishes available at an extra cost. Steel structure: Steel structure made of high-strength fine-grain steels. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders tested according to DIN-EN 287-1. Welding process MAG according to EN ISO 4063. Protective gas M21 according to EN ISO 14175 Front wall made of steel, plug-in, approx. 400 mm high Connection strip for supply lines to the tractor unit, mounted at the height of the outer frame profile. ASPÖCK-UNIBOX on the connection strip at the front with sockets 24N, 24S & 15-pole. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pole connection according to ISO-12098 If your pin assignment differs from the ISO connection standard, please inform us. "Anderson" socket on the connection strip at

Condition: used, operating hours: 840 h, machine/vehicle number: 2036114, fuel type: diesel, Year of manufacture: 2018 Unladen weight: 3,440 kg Lifting capacity: 565 kg Working height: 1,020 cm Dimensions of the loading area: 318 x 178 x 244 cm Cedpszynrrofx Aafsri Condition of front tires: 70 Condition of rear tires: 70 Please contact PFEIFER GROUP for further information.

Condition: used, operating hours: 1,117 h, machine/vehicle number: 2037628, fuel type: diesel, Year of manufacture: 2018 Unladen weight: 3,440 kg Crjdpfozynrfex Aafji Lifting capacity: 565 kg Working height: 1,020 cm Dimensions of the cargo area: 318 x 178 x 244 cm Condition of the front tires: 80 Condition of the rear tires: 80 Please contact PFEIFER GROUP for further information.

Condition: new, empty load weight: 10,350 kg, maximum load weight: 39,150 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with rear slope of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood deck, 30 mm thick Loading platform: -Telescoping loading platform with rear slope of approx. 1,000 mm x 8° -1 pair of permanently installed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm -Wheel recesses with square climbing strips 15 x 15 mm and widening in the lower area -Between the 1st and 2nd axles, a pair of permanently installed wheel recesses, approx. 1,610 x 970 x 400 mm -3-part removable galvanized covers over the wheel recesses (W 670 mm) - max. point load 5 tons / piece -Recess in the slope and extending into the loading platform to accommodate the excavator arm, approx. 2,900 x 750 x 210/290 mm -1 pair of lashing rings lying at the front in the loading platform (LC 10,000 daN) -5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) -2 pairs of lashing rings that can be folded outwards (LC 10,000 daN) -2 pairs of lashing rings in the excavator arm recess (LC 5,000 daN) -Cutouts in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) One-piece aluminum ramps: -A pair of one-piece aluminum ramps, approx. 2,500 x 600 mm -Ramp with spring lift mechanism and manually adjustable -Maximum load per pair: 24,000 kg Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle steered -Technical axle load: 12,000 kg -Electromagnetic reversing lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -Axle tool -Tires 235/75 R 17.5 -TPMS tire pressure monitoring system according to ECE R 141 Included accessories: -One spare wheel with holder in front of the front wall -2" kingpin -One galvanized steel front wall, approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 pieces of wheel chocks with holder on the front wall -Mounting in the rear area of the gooseneck for aluminum ramps -Widening, galvanized, extendable by approx. 230 mm on each side -Galvanized folding supports under the slope of the loading platform -One mounting for a rotating beacon on the rear of the trailer -White reflector tape according to EU regulations on the side, on the extension and red at the rear -On the gooseneck and on the rear panel, one mounting each on the left and right for warning signs including socket -On the gooseneck, aluminum side and rear panels that can be plugged in, approx. 2,440 x 400 mm -The rear galvanized slotting strips are removable (length of the structure approx. 2,560 mm) Credpfeiu Er Aox Aafei -2 pairs of WADER container pockets in the loading platform for a 20ft or 30ft container -3 pairs of rung pockets for slotting strips 100 x 50 mm in the outer frame of the loading platform -One removable galvanized intermediate table with 1 pair of WADER container pockets -Square climbing strips 20 x 20 mm every 200 mm on the outer frame of the slope of the loading platform -A sand coating is applied to the diamond-patterned plates on the gooseneck and on the loading platform for slip resistance -Four warning signs, each extendable by approx. 400 mm, approx. 423 x 423 mm, with a position light -On the warning signs, a mounting for a rotating beacon -Speed sticker 80 km/h at the rear and on both sides -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel structure shot blasted, then the defined visible sur

Condition: used, operating hours: 863 h, machine/vehicle number: 2035403, fuel type: diesel, Year of manufacture: 2018 Unladen weight: 3,440 kg Lifting capacity: 565 kg Working height: 1,020 cm Dimensions of the cargo area: 318 x 178 x 244 cm Condition of the front tires: 80 Condition of the rear tires: 80 Credpjz Anm Isfx Aafei Please contact PFEIFER GROUP for further information.

Condition: used, fuel type: diesel, Year of manufacture: 2016 Credpfxo Adnurj Aafji Lifting capacity: 565 kg Please contact Gebrauchtgeräte Center for more information

Condition: used, maximum load weight: 44,980 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, first registration: 09/2024, next inspection (TÜV): 09/2025, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Chassis, bent * Special steel frame made of high-strength fine-grain steels, electrically welded at the joints, well-dimensioned outer frame * 4-axle arrangement. Wheel protection above the axles with spray mist suppression * All steel parts sandblasted * Lateral impact protection made of anodized aluminum mounted * Increased point load of approx. 30,000 kg over approx. 4,000 mm * Special design in the bent area for maximum low-bed length in combination with AluLeg outrigger supports instead of telescopic outrigger winches, max. rear swivel radius of the tractor unit approx. 2,100 mm Special superstructure with rear beam extension * Self-supporting aluminum roof beam / profile approx. 120 x 100 mm, sliding tarpaulin with plastic flaps * Rear beams extendable to approx. 4,200 mm * Three sliding beams per side with rubber cord relief * Additional center beam locking in the roof beam and parking position, by means of a pull cable and spring latch * Lifting roof mechanically adjustable, lifting height approx. 400 mm, can be operated on both sides or on one side, without opening the opposite side and the doors * Additional height adjustment of approx. 480 mm in approx. 40 mm increments with height adjustment in the beams * Front overhang on the front wall for operation under tarpaulin up to a total height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminum slats on the side, bottom 450 mm pockets, above 4 rows of single pockets Csdelthgujpfx Aafori * Only 3 rows of insert slats in the upper bed. Spacing between slats evenly distributed Floor * Approx. 27 mm special water-resistant glued beech plywood, rough surface * Steel sheet in the wheel arch area * Forklift truck accessible according to DIN standard * Outer frame flush with the surface Brakes * WABCO compressed air brake system with EBS according to EC standard 71/320 EEC including PREV (parking release safety valve) * Spring brake cylinders as parking brake * Wabco Smart Board with odometer and aggregate load indicator Axles * 4 x 10,000 kg SAF/Sauer with drum brakes in low-loader design * Air suspension with lifting and lowering device, total stroke approx. 230 mm * Third and fourth axles as friction-jointed trailing axles with electric and mechanical lock Twin tires * 235/75 R 17.5, -16-ply, incl. E-wheel holder. without E-wheel Paint finish * Chassis in RAL 3002 red, solid color * Center beams, axles coated with KTL black * Corner beams in hot-dip galvanized design * Plastic parts black * Hot-dip galvanized parts unpainted * Rims in factory silver * Superstructure in RAL color, solid color Special equipment incl. * Air suspension in ECAS design, operated on the semi-trailer * Overwidth signs front and rear in zinc-plated, steplessly telescopic design with attached warning lights including socket for rotating beacons (small panels) * Sliding tarpaulin cover locking additionally from the outside * 4 beam adapters for special outer frame profile, to lock the center beams as desired * PVC sliding tarpaulin, color similar: RAL 9006 silver * Roof tarpaulin translucent, in overwidth and overheight design, flat hooks, tarpaulin folds, closures with pawl lock /OCS * Telescopic socket for rotating beacon including beacon on the rear left * Outer frame for machine transport with app

Condition: used, Year of construction: 2018, operating hours: 896 h, machine/vehicle number: 2046899, fuel type: diesel, Unladen weight: 3,440 kg Lifting capacity: 565 kg Working height: 1,020 cm Csdpszynr Sefx Aafjri Dimensions of the cargo area: 318 x 178 x 244 cm Condition of the front tires: 80 Condition of the rear tires: 80 Please contact PFEIFER GROUP for further information.

Condition: used, Year of construction: 2018, operating hours: 609 h, machine/vehicle number: 2036768, fuel type: diesel, Unladen weight: 3,440 kg Cjdpfxsz Skmps Aaferi Lifting capacity: 565 kg Working height: 1,020 cm Dimensions of the cargo area: 318 x 178 x 244 cm Condition of the front tires: 80 Condition of the rear tires: 80 Please contact PFEIFER GROUP for further information.

Condition: new, mileage: 4 km, power: 355 kW (482.67 HP), fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, brakes: retarder, color: white, gearing type: automatic, emission class: euro6, Year of construction: 2026, Equipment: ABS, air conditioning, electronic stability program (ESP), navigation system, parking heater, soot filter, Equipment: * FAN XG 480 Multi-changer 1120-1320 with tail lift * Chassis front design: Aero base plate * Air-suspended cab * Laminated glass with sun protection film * Central locking, 3 keys, 2 remote controls * Windscreen with sun protection film * External sun visor * Two LED work lights on the rear cab wall * Reversing camera, prewiring for 2nd camera * DAF Corner View * Handles, trims, and side panels in cab color * LED headlights, cornering and fog lights Csdpfjy A Uvfex Aafsri * Fixed cab entry * XG cab * LED skylights * LED daytime running lights * Adjustable roof spoiler for XG cab * Lower cab step: Crystal White * Side skirt housing black for cab color Crystal White * Chassis color: anthracite grey * CRYSTAL WHITE * Headlight trim color: Crystal White * Bumper color: Crystal White * Roof spoiler color: Crystal White * Electrically operated roof hatch * Integrated stationary air conditioning * Driver’s seat: Luxury Air * Preparation for pneumatic device * Passenger seat: cinema & table, fabric cover * Driver’s seat with swivel base * Xtra Comfort mattress for lower bunk * Upper bunk * Automatic climate control for cab * Refrigerator and drawer * Armrests on both sides of the driver’s seat * Storage compartment with drawer in center console * Luxury LED interior lighting * ECAS remote control with extended functions * Interior trim color scheme: Exclusive * Dashboard table * Steering wheel with silver accents * Cab interior design: Hexagon * Safety nets at both bunks * Curtains, no dividing curtain * Dashboard design: Plateau * Auxiliary heater with waste heat pump and timer * Wireless charger * Speakers: Exclusive * Digital tachograph, VDO version G2V2A * Speed limiter setting: 90 km/h * PACCAR Connect with navigation * Antennas: Radio, 2x mobile, GNSS Extra: CB * FMS connector, extended and prewired * Infotainment including DAF Truck Navigation * Adaptive Cruise Control with FCW and AEBS-3 * Predictive Cruise Control * Toll system preparation * Driver Performance Assistant * Reversing warning system * Lane departure warning system * Start assist * DAF Side and Turn Assist * Electronic stability control (VSC) * Speed limit recognition * DAF Drowsiness & Distraction Detection * Standard immobilizer * Automatic lift operation * Front air suspension: medium * Front: 8.00 t, air suspension, 161 N * Rear axle load capacity 13.00 t * Tag axle load 8.0 t * Load limiter 11.5 t * Axle load ratio 11.5/7.5 * Lifting device * Rear: 20.00 t, air suspension, SR1344 * Continental * F1, 315/70R22.5 CGW CEPS5 158/150 L Steering ABA 3P * R1, 315/70R22.5 CGW CEPD5 154/150 L Traction ACA 3P * R2, 315/70R22.5 CGW CEPS5 158/150 L Steering ABA 3P * Silver-grey wheel trims * Tire pressure monitoring system * Steel disc wheels, silver-grey * Urge-to-move * Mechanical differential lock * Traction aid 15.0 t * MX-13 engine, 355kW/483HP, cab emblem: 480 * Emission standard Euro 6 * Standard transport, full version * Eco-Fuel * Idle shutdown automatic, 5 minutes * Automated gearbox, TraXon, 12-speed * Automated manual gearbox, full version * Final drive ratio 2.21 * Traction control (ASR) * 12-speed TraXon gearbox 12TX2210 DD, 16.69-1.00 * ZF-Intarder * 2-cylinder compressor with clutch * Driven rear axle with disc brakes * Pneumatic control for parking brake * Wheels

Condition: used, Year of construction: 2018, operating hours: 426 h, machine/vehicle number: 2048010, fuel type: diesel, Unladen weight: 3,440 kg Lifting capacity: 565 kg Working height: 1,020 cm Dimensions of the cargo area: 318 x 178 x 244 cm Credoz Rt Nvopfx Aafji Condition of the front tires: 80 Condition of the rear tires: 80 Please contact PFEIFER GROUP for further information.

Condition: used, machine/vehicle number: 2170909, fuel type: diesel, Year of manufacture: 2026 Crsdpfxoz Enkis Aafei Unladen weight: 3,350 kg Lifting capacity: 565 kg Working height: 1,028 cm Dimensions of the loading area: 318 x 178 x 244 cm Condition of front tires: 0 Condition of rear tires: 0 Please contact PFEIFER GROUP for further information.

Condition: used, maximum load weight: 34,760 kg, overall weight: 40,000 kg, axle configuration: 3 axles, first registration: 06/2024, next inspection (TÜV): 06/2025, Warranty extension * on the KRONE axle: 6 years with no mileage limit for on-road use within the EU, load-dependent, fully automatic, electronic lift axle control for 1st axle, manual function Krone axles 9t, 6-year warranty on Krone axles with no mileage limit, LED side marker lights with flashing function, Hella LED tail lights, ADR warning sign, B 028.001 Two mechanical support winches, 2 x 12 tonnes, semi-circular with base plate, make: Jost B 001.000 Support winches operated on one side, in FR-right, multi-function tail lights (full LED), make Hella (Gen.2) Krone warranty: 10 years g. Rust-free underrun protection, extendable, 1 x 40`container with tunnel, 1 x 45`container with tunnel, 2 x 20`containers, 1 x 20`container flush with the rear, 1 x 20`container in the middle, NOT for tank containers, lifting axle A 420.000 Container locks for holding the following containers: A 420.101 1 x 40' container with tunnel A 420.152 1 x 45' container with tunnel A 420.110 2 x 20' containers A 420.140 1 x 20' container flush with the rear A 420.120 1 x 20' container in the middle Color group 1. Color group vehicles: 2 vehicles X 998.107 Chassis RAL 9005 DEEP BLACK X 998.130 Axles incl. Wheel hubs RAL 9005 DEEP BLACK X 998.242 Underrun protection/lighting bracket WHITE POWDER COATED X 998.890 Attachments BLACK OR GALVANIZED X 998.212 Rims SILVER NATURAL X 998.272 Side impact protection WHITE POWDER COATED X 998.831 Landing gear RAL 9005 DEEP BLACK Crodpfx Asnudhmoafsi

Condition: used, Year of construction: 2018, operating hours: 572 h, machine/vehicle number: 2037342, fuel type: diesel, Unladen weight: 3,440 kg Lifting capacity: 565 kg Working height: 1,020 cm Dimensions of the cargo area: 318 x 178 x 244 cm Condition of the front tires: 80 Crodpfx Aajz Dffzofei Condition of the rear tires: 80 Please contact PFEIFER GROUP for further information.