Low loader trailer

FLIEGL VTS 400

Condition: new, maximum load weight: 30,010 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,000 mm, loading space width: 2,520 mm, loading space height: 900 mm, total width: 2,550 mm, Brand-new Fliegl 4-axle low-bed trailer with wheel recesses and split ramps, type VTS 400 RM Hire-purchase offer: 48-month term, down payment only the VAT, final residual value 40% Monthly rate: EUR 899.00 Vehicle / Body: Low-bed trailer First registration: New vehicle Gross weight: 24,000kg/40,000kg Unladen weight: 9,990kg Payload: 14,010kg / 30,010kg Overall length: 12,000mm Bdedpstrizkofx Akcjf Loading length: total approx. 10,000mm, gooseneck approx. 2,850mm, load bed including rear taper approx. 7,150mm Width: 2,550mm Loading height: 900mm Further information Chassis: Low-bed trailer Steel welded construction Turntable with heavy-duty ball race Foldable rear support Wheel chocks with holders Aluminum side underrun protection Full-width rear spray flap Half-shell mudguards 1st and 2nd axle with anti-spray mud flaps behind each axle, anti-spray mud flap behind the 4th axle Excavator arm trough above rear axles, from the rear axle to the rear approx. 1,800mm long, approx. 650mm wide and 150mm deep 2 pairs of lashing holes, each 5t, in the excavator arm trough, on the longitudinal frame approx. 300mm from the front and approx. 200mm before the rear taper Spare wheel bracket for 1 spare wheel, upright on the gooseneck, front center, spare wheel brand same as main equipment, steel rim Toolbox let into the floor on the gooseneck with lid, W=720mm / L=520mm / D=170mm 1st pair of wheel recesses after the gooseneck, let into the deep deck in the driving lane, chamfered for access, length at the bottom approx. 1,600mm, approx. 400mm deep. Note! Frame in the main beam area 400mm higher than the wheel recess. 2nd pair of wheel recesses between the axles, let into the deep deck in the driving lane, chamfered for access, length at the bottom approx. 600mm, approx. 300mm deep. Note! Frame in the main beam area 300mm higher than the wheel recess. Extensions retractable to 3,000mm (no extension at the rear taper and not in the wheel recesses below) (track width of machines or vehicles to be transported must not exceed the outer frame width of 2,550mm) Storage compartment for timber planks underneath the low-bed deck 70mm timber planks for extension to 3,000mm Lashing points – low-bed trailer 1 pair of RIN lashing rings inlaid at the front on the gooseneck, each 5t 4 pairs of lashing holes in the outer frame, each 5t (for securing strap attachments) 8 pairs of lashing mushrooms flush-mounted top and side in the outer frame, each 10t 2 at the front on the gooseneck 6 in the deep deck First lashing ring 250mm from the front, last a maximum of 250mm from the rear, spacing between lashing rings not more than 1,100mm 5 pairs of stake pockets inlaid in the outer frame, inner dimensions 70 x 40mm (convertible to 5t ring lashing eyes, not included) 1 pair of foldable lashing rings additionally inlaid in the floor, each 10t 1 inside next to main frame at start of low-bed section 2 pairs of additional foldable lashing rings, each 10t 1 on the gooseneck (protrudes) 1 behind the last axle inlaid in the floor Towing device for turntable trailer Drawbar with certified 50mm towing eye, towing eye inclined by 8° D-value at least 160kN Axles and Suspension BPW drum braked axles "Axles/chassis laser aligned" – reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical front axle load equalization (rocker equalizer) Wheels and Tires 235 / 75 R 17.5" Manufacturer’s choice, with M + S marking Steel rims in twin arrangement,

Condition: used, empty load weight: 9,980 kg, maximum load weight: 30,020 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 02/2022, loading space length: 10,200 mm, loading space width: 2,520 mm, loading space height: 950 mm, suspension: air, tire size: 235/75R17.5, color: grey, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 4 axles, SAF axles, turntable, air suspension, ABS (anti-lock braking system), extendable to 3m, lashing points, 2-part loading ramps, hydraulic ramps, side aluminum fender, twin tires, wheel recesses. Superstructure: 4-axle low-bed trailer with wheel recesses, excavator arm recess, and hydraulic ramps, in like-new condition! 4x 10t SAF axles, drum brakes, total weight technically 40,000 kg, loading length of the gooseneck approx. 2800 mm, loading length of the low-bed platform approx. 7400 mm, extendable to 3000 mm, 50 mm drawbar eye, 1st pair of wheel recesses approx. 1600 mm long, 2nd pair of wheel recesses approx. 600 mm, ramp length approx. 3850 mm, ramps are hot-dip galvanized, ramps can be hydraulically shifted sideways. Loading height of the front wheel recess approx. 560 mm! Loading height of the rear wheel recess approx. 650 mm! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale and errors! Bdjdpfx Aezg Ev Ujkcof

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 9,900 kg, maximum load weight: 14,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Custom-tailored transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Further information Chassis Steel welded construction Turntable with robust ball bearing, storage box recessed Turntable extension Foldable rear support 2 wheel chocks with holder Aluminum side impact protection Mud flaps at the rear across the entire width Extendable wideners to 3,000 mm (not in rear slope) (However, the track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the center of the loading area Wooden planks 70 mm for widening to 3000 mm Tie-down eyes, low-loader type 3 pairs of tie-down points, each rated at 10 tons, integrated in the front of the floor 6 pairs of tie-down anchor plates, top and side in the outer frame, each rated at 10 tons 1 x in the neck area the rest distributed in between with a maximum distance of 1200 mm 1 x rear slope 5 pairs of pocket slots recessed in the outer frame, inside 70 x 40 mm, (can be converted to 5-ton ring tie-down eyes, not included in the scope of supply) Towing device, turntable trailer Tow bar with tested 40 mm towing eye Note! With a 40 mm towing eye, the permissible total weight of the truck must not exceed 18000 kg; otherwise, a 50 mm towing eye is required. Axles + Suspension SAF drum brake axles Axle / chassis laser-aligned, reducing tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load equalization in the front and rear (rocker equalization) Wheels & Tires 235 / 75 R 17.5, according to manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be pulled by towing vehicles which guarantee the effectiveness of the ABS! Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connecting cable 1 LED rotating beacon with holder, switched via parking light (beacon can be removed) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area: steel floor followed by 70 mm softwood floor, steel / diamond plate in the wheel arch area Rear slope with 70 mm softwood floor Access Ramps Steel ramps, 2800 mm long, 750 mm wide, laterally movable covered with wood with gas spring support Operating Instructions With an axle load of 10,000 kg, an exemption permit is required, only indivisible loads are possible!!! The stated total weight is technically possible; depending on the cargo, the total weight may not be reached while complying with the permissible axle / support and saddle loads. Country of Registration / Signs Country of Registration: Germany 1 with Dekra inspection and certificate (according to §13 EG - FGV) 24/7 service hotline prepared for license plate holder, two-line Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Bdedpfji Ri I Esx Akcjf Paint finish Frame: RAL 3002 Carmine Red 10-year warranty against rust-through Tow bar: galv

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 8,500 kg, maximum load weight: 15,500 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, loading space width: 2,520 mm, loading space height: 890 mm, total length: 11,940 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer requirements. Further Information Bdedpfx Akji Ri Izocof Low-loader trailer chassis Steel welded construction Turntable with heavy-duty ball bearing Foldable rear support 2 support wedges with holder Aluminum side impact protection Splash guards at the rear over the entire width Quarter panel fenders in front of the 1st axle Extendable widening elements to 3,000 mm (not in rear slope) (However, the track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the center of the loading area Wooden planks 70 mm for widening to 3000 mm Tie-down points for low-loader 1 pair of tie-down points on the gooseneck, each 5 tons 9 pairs of tie-down eyes embedded at the top and sides in the outer frame, each 10 tons 2 x at the front on the gooseneck 7 x in the low bed 6 pairs of tie-down holes in the outer frame of the low bed, each with 5 tons. (for securing lashing straps) Coupling device for trailer turntable Drawbar with tested 50 mm drawbar eye Axles + Suspension SAF drum brake axles Axle/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical incl. Axle load equalization at the front and rear (lever equalization) Wheels and tires 235 / 75 R 17.5 according to the manufacturer's choice Steel rims in twin arrangement, factory silver Braking system 2-line compressed air braking system Spring brake parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red marker lights at the rear 1 LED warning light with holder, switched via side lights (light can be removed) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin fail-safe plugs at the front, with connecting cable Floor Gooseneck at the front with steel/diamond plate thereafter with 70 mm softwood floor, in the wheel arch area steel/diamond plate Rear slope with 70 mm softwood floor Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally movable covered with wood Hydraulically operated via tractor's auxiliary drive with throttle, operation on the left side Hydraulic connection with quick-release coupling NW 10/3, incl. connecting hose Operating instructions At 10,000 kg axle load, an exemption permit is required, only indivisible loads are possible!!! The stated total weight is technically possible; depending on the cargo, the total weight may not be reached while observing the permissible axle/support and saddle loads. (Poor driving and handling behavior possible due to incorrect load distribution) Country of registration / Signs Country of registration: Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline included prepared for license plate holder, two-line Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Painting Frame DB 7350 Novagrau 10-year warranty against rusting Drawbar galva

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 14,300 kg, maximum load weight: 9,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space width: 2,520 mm, loading space height: 900 mm, total length: 12,000 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Further Information Chassis Steel welded construction Turntable with robust ball bearing Foldable rear support 2 wheel chocks + holder Aluminum side underrun protection Splash guards at the rear over the entire width Quarter panel fenders in front of the 1st axle Excavator arm recess starting above the rear axles to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing points of 5 tons each in the excavator arm recess on the side of the longitudinal frame, approx. 300 mm from the front and approx. 200 mm in front of the rear slope Bdodpji Ri I Nofx Akcof 1 storage box recessed in the gooseneck in the floor with a lid, W=720 mm/ L=520 mm / D= 170 mm 1st pair of wheel recesses recessed in the gooseneck in the low-loader wheel well area, sloped for access, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area is 400 mm higher than the wheel recess. 2nd pair of wheel recesses between the axles recessed in the low-loader in the wheel well area, sloped for access, length at the bottom approx. 600, approx. 300 mm deep. Note! Frame in the main beam area is 300 mm higher than the wheel recess. Wheel recess cover pull-out from the main frame, with wood inserts. Distance from the outer frame, beam to beam, approx. 1280 mm Extensions pull-out to 3,000 mm, foldable at the wheel recess extensions (extension not in the rear slope and not in the wheel recesses at the bottom) Storage compartment for wooden planks in the middle of the loading area or under the loading area, depending on technical feasibility Wooden planks 70 mm for extension to 3000 mm Lashing points, low-loader 1 pair of ring lashing points recessed at the front on the gooseneck, each 5 tons 8 pairs of lashing eyes at the top and on the side recessed in the outer frame, each 10 tons 2 x at the front on the gooseneck 6 x in the low-loader, the first lashing point 250 mm from the front and the last one max. 250 mm from the rear, the distance between the lashing points is no more than 1100 mm 5 pairs of ring lashing points recessed in the outer frame, each 5 tons (can be converted to stake pockets) Coupling system, trailer, turntable Drawbar with tested 50 mm drawbar eye with 8° inclined drawbar eye Axles + Suspension SAF drum brake axles Axle/chassis laser-aligned, reducing tire wear and fuel consumption Air suspension with lifting and lowering valve, can be operated separately at the front and rear Wheels and tires 235/75R17.5 according to manufacturer's choice Steel rims in twin arrangement, factory silver Braking system 2-line compressed air brake system Spring-loaded parking brake Trailer Info Center for displaying vehicle data such as axle load (no calibrated scale) and odometer Axle load detection via EBS-CAN bus signal, for display on the display in the cab, truck must be suitably prepared, no truck installation (no calibrated scale) Vehicle-driving stability system Duomatic connection at the front, with connecting cable to the towing vehicle EBS, Electronic Braking System with EBS plug at the front, with connecting cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrical system 24 Volt, multi-chamber lights in LED with resistor, yellow LED lighting on the side, license plat

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, overall weight: 24,000 kg, axle configuration: > 3 axles, loading space height: 900 mm, total length: 11,940 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Additional Information Low-bed semi-trailer chassis Steel welded construction Turntable with heavy-duty ball bearing ring Folding rear outriggers 2 support wedges with holder Aluminum side impact protection Rear splash guards covering the entire width Semi-fender for 1st and 2nd axles with anti-spray splash guards behind each axle, anti-spray splash guards in front of and behind the 3rd and 4th axles Excavator arm recess above the rear axles, extending to the rear, approximately 1800 mm long, approximately 650 mm wide and approximately 150 mm deep, 2 pairs of lashing points of 5 tons each in the excavator arm recess, laterally on the longitudinal frame, approximately 300 mm from the front and approximately 200 mm in front of the rear slope 1 plastic toolbox, with insert, w=620/h=360/d=440 mm, lockable with a padlock (lock not included) 1 storage box recessed in the gooseneck at the bottom with lid, W=720 mm/ L=520 mm / D= 170 mm Extendable widening elements to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Storage compartment for wooden planks under the loading platform Lashing eyes for low-bed trailer (40 lashing options) 1 pair of lashing eyes on the gooseneck, each 5 tons 9 pairs of lashing eyes embedded above and on the side in the outer frame, each 10 tons 2 x at the front on the gooseneck 7 x in the low bed 6 pairs of lashing eyes in the outer frame from the low bed, each 5 tons (for attaching tie-down straps) 3 pairs of folding lashing eyes additionally, each 10 tons 1 x inside next to the main frame at the beginning of the low bed 1 x on the gooseneck (protruding) 1 x behind the last axle, recessed in the floor Coupling device for the trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined by 8° / D-value min. 160 kN Bsdpfxei Ri Daj Akcedf Axles + Suspension Drum brake axles Parabolic spring suspension with maintenance-free steel-rubber bearing and mechanical axle load equalization at the front and rear (rocker equalization) Wheels and Tires 235 / 75 R 17.5 according to the manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, with connecting cable Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking lights (beacon removable) 2 pairs of warning signs double LED illuminated and extendable to 3,000 mm Floor Gooseneck at the front with steel / checkered plate covering followed by 70 mm softwood floor, wheel arch area with steel / checkered plate covering Rear slope with 70 mm softwood floor Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable covered with wood Hydraulically operated via towing vehicle auxiliary drive with throttle, operation on the left-hand side at the front Hydraulic connection with SVK plug NW 10/3, incl. connecting hose Country of Registration / Signs Country of Registration: Germany 24/7 Service Hotline prepared for two-line license plate holder Contour marking with reflective strips ac

Condition: new, maximum load weight: 31,920 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,410 mm, loading space width: 2,500 mm, loading space height: 900 mm, total width: 2,550 mm, New vehicle Fliegl 4 axle low loader trailer with ramps, type VTS 400 Total weight: 24,000kg/40,000kg Empty weight: 8,080kg Payload: 15,920kg/31,920kg Total length: 11,940mm Loading length: total approx. 10,410mm, offset approx. 2,490mm, loading bed including rear bevel approx. 7,920mm Width: 2,550mm Loading height: 900mm Further information plus pre-freight / provision from storage location 26639 Wiesmoor 1,280.00 ¤/ net Bsdevv D Ixspfx Akcodf Rent-purchase offer: term 48 months, down payment only VAT, residual value 40% monthly rate EUR 759.00 Chassis Low-loader trailer Steel welded construction Turntable with strong ball bearing ring Foldable rear support 2 wheel chocks with holder Aluminum side impact protection Rear splash flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray splash flaps behind each axle, Anti-spray splash flaps in front of and behind 3rd and 4th axle Excavator arm recess over the rear axles starting at the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes, each 5 tons. in the excavator arm recess on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear bevel 1 plastic tool box, w=600 / h=425 / d=460 mm, lockable Storage box embedded in the floor on a crank with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm (not in the rear bevel) (The track width of the construction machines or vehicles to be transported must not exceed the outer frame width 2,550 mm) Storage compartment for wooden planks below the low-loading area Wooden planks 70 mm for widening to 3,000 mm Lashing eyes for low-loader 1 pair of lashing cutouts embedded in the longitudinal beam at the front on a crank, 10 tons each. 4 pairs of lashing holes in the outer frame, each with 5 tons (tension belt attachment) 9 pairs of lashing mushrooms, each 10 tons, embedded in the outer frame at the top and side 2 x at the front on the bend 7 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the back, distance between the lashing eyes not greater than 1100 mm 3 additional pairs of folding lashing eyes, each 10 tons 1 x on the bend (sticks out) 1 x at the beginning of the low bed, embedded inside on the longitudinal beams 1 x embedded in the floor behind the last axle Towbar with tested 50 mm towing eye Towbar height adjustment via spring Axles + suspension Drum brake axles, as selected by the manufacturer "Laser-measured axles/chassis" Reduction in tire wear and fuel consumption Air suspension with raising & lowering valve + Auto-reset function Wheels and tires 235 / 75 R 17.5" at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Axle load detection via EBS-Canbus signal, for display on display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle - driving stability system 2 interchangeable coupling heads at the front, with connecting cables to the motor vehicle, 12-24 volt EBS, electronic braking system with EBS plug at the front, with connecting cable Knorr brand Caution: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrics 12-24 volts, multi-chamber LED lights, yellow LED lighting on the side, license plate lighting in LED, (Note! Incorrect diagnoses can occur with certain towing vehicles, although the function is p

Condition: new, maximum load weight: 31,920 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,410 mm, loading space width: 2,500 mm, loading space height: 900 mm, total width: 2,550 mm, New Fliegl 4-Axle Lowbed Trailer with Ramps, Model VTS 400 Gross weight: 24,000 kg / 40,000 kg Unladen weight: 8,080 kg Payload: 15,920 kg / 31,920 kg Total length: 11,940 mm Loading length: approx. 10,410 mm total, gooseneck approx. 2,490 mm, loading platform incl. rear chamfer approx. 7,920 mm Width: 2,550 mm Loading height: 900 mm Additional information: Plus delivery/preparation ex stock 26639 Wiesmoor €1,280.00 net Chassis - Lowbed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear supports 2 wheel chocks with holders Side underrun protection - aluminum Full-width rear mudflap Half-shell fenders on 1st and 2nd axles with anti-spray flaps behind each axle Anti-spray flaps in front of and behind 3rd and 4th axles Excavator arm recess above the rear axles extending to the rear, approx. 1,800 mm long, approx. 650 mm wide, approx. 150 mm deep 2 pairs of lashing holes (5 t rating each) in the excavator recess, on the longitudinal frame approx. 300 mm from the front and approx. 200 mm before the rear chamfer 1 plastic toolbox (W=600 mm, H=425 mm, D=460 mm), lockable Storage box flush-mounted in floor on the gooseneck, with lid (W=720 mm, L=520 mm, D=170 mm) Extendable widening beams to 3,000 mm (not at rear chamfer) (Note: Maximum track width of construction machines or vehicles must not exceed outer frame width of 2,550 mm) Stowage compartment for wooden planks under the lowbed deck Wooden planks 70 mm wide for extension to 3,000 mm Lashing points - Lowbed 1 pair of recessed lashing cutouts in front longitudinal beam on gooseneck, each rated 10 t 4 pairs of lashing holes in outer frame, each rated 5 t (for attaching tie-down straps) 9 pairs of lashing pins installed flush on top and side of outer frame, each rated 10 t 2 x front on gooseneck 7 x in the lowbed First lashing point 250 mm from front, last max. 250 mm from rear, distance between points no greater than 1,100 mm 3 additional pairs of folding lashing rings, each rated 10 t: 1 x on gooseneck (protruding) 1 x at the start of the lowbed, inset into the longitudinal beams 1 x recessed in floor behind the last axle Towing Arrangement – Turntable Trailer Drawbar with certified 50 mm towing eye Drawbar height adjustable via spring Axles & Suspension Drum brake axles, manufacturer’s choice "Axle/chassis laser alignment" for minimizing tire wear and fuel consumption Air suspension with raise/lower valve and auto-reset function Wheels & Tires 235/75 R 17.5", manufacturer’s choice Steel rims with twin arrangement, factory silver Brake System 2-line compressed air brake system Spring-applied parking brake Axle load detection via EBS CAN bus signal for display in the truck cab (truck must be pre-equipped; not a calibrated scale) Vehicle – Driving Stability System 2 foolproof coupling heads at front with connecting lines to tractor unit 12-24 Volt EBS, electronic braking system with EBS plug at the front and connection cable (Knorr brand) Note: The towed trailer may only be towed by tractors that guarantee the effectiveness of the ABS! Electrical System 12-24 Volt, multi-chamber LED lights, side yellow LED lighting, LED license plate lighting (Note: Certain tractor units may indicate malfunctions even if all functions are working) 2 white LED position lights at front 2 white/red LED lane marker lights at rear 2 x 7-pin foolproof connectors at front with connection cable 1 LED beacon with holder (switchable via parking lights; lamp removable) Bdedpexrx Nljfx Akcof

Condition: new, maximum load weight: 30,310 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, NEW VEHICLE Fliegl 4-axle low loader with 2 pairs of wheel recesses and ramps Total weight 40,000 kg Payload 30,310 kg Empty weight 9,690 kg Total length 12,000 mm Loading length 10,000 mm Loading bed 7,150 mm including 850 mm approach slope Loading height 900 mm 1st pair of wheel recesses after offset in the loading bed, bottom length approx. 1,600 mm, 400 mm deep 2nd pair of wheel recesses between the axles in the loading bed, bottom length 600 mm, 300 mm deep Extensions to 3,000 mm, warning signs, rotating beacon, large lashing package 5 pairs of stake pockets in the outer frame Excavator arm recess 1,800 mm long, 150 mm deep Drawbar 50 mm Air suspension with lifting and lowering valve, can be operated separately BPW drum brakes Bdjdpfx Aenzlg Djkcof Tires 235 / 75 R 17.5" Axle load detection via EBS CAN bus signal, Trailer Info Center Ramps 2,800 mm x 750 mm with hydraulic actuation Hydraulic side shift Rent-purchase offer: term 48 months, residual value 40%, down payment only VAT on the rental rates, monthly rate EUR 970.00 net Vehicle will be available from September 11th, 2023 from the Neumünster trade fair. Visit us at Nordbau - Stand West 121 right next to the main entrance. Other 3, 4 and 5 axle low loaders new and used available immediately

Condition: new, maximum load weight: 31,100 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,410 mm, loading space width: 2,500 mm, loading space height: 900 mm, total width: 2,520 mm, Total weight: 24,000kg/40,000kg Empty weight: 8,900kg Payload: 15,100kg/31,100kg Total length: 11,940mm Loading length: 10,410mm total, 2,490mm offset, 7,920mm loading bed including rear bevel Width: 2,520mm Loading height: 900mm Further information plus pre-freight / provision from storage location 26639 Wiesmoor 1,280.00 €/net Steel welded construction Turntable with strong ball bearing ring Foldable rear support Wheel chocks with holder Aluminum side impact protection Rear splash guards across the entire width (not in conjunction with forklift bracket) Half-shell mudguards 1st + 2nd axle with anti-spray splash guards behind each axle, Anti-spray flaps in front of and behind the 3rd and 4th axle Excavator arm recess above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons. in the excavator arm recess on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear bevel 1 plastic tool box, w=600 / h=425 / d=460 mm, lockable 1 storage box embedded in the floor on a crank with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm (not in the rear bevel) (The track width of the construction machines or vehicles to be transported must not exceed the outer frame width 2,550 mm) Storage compartment for wooden planks below the low-loading area Wooden planks 70 mm for widening to 3,000 mm Lashing eyes for low-loader 1 pair of lashing cutouts in the longitudinal beam at the front on a crank, 10 tons each. 4 pairs of lashing holes in the outer frame, each with 5 tons (tension belt attachment) 9 pairs of lashing mushrooms, embedded in the outer frame at the top and sides, each with 10 tons 2 x at the front on the bend 7 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the back, distance between the lashing eyes not greater than 1100 mm 3 additional pairs of folding lashing eyes, each with 10 tons Bjdpfjrducpjx Akcedf 1 x on the bend (sticks out) 1 x at the beginning of the low bed, embedded inside on the longitudinal beams 1 x embedded in the floor behind the last axle Towbar with tested 50 mm towing eye Towbar height adjustment via spring Axles + suspension Drum brake axles, as selected by the manufacturer "Laser-measured axle/chassis" Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free Steel-rubber bearings and mechanical axle load compensation at the front and rear (rocker compensation) Wheels and tires 235 / 75 R 17.5" at the manufacturer's discretion Steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake 2 interchangeable coupling heads at the front, with connecting lines to the towing vehicle, 24 volt ABS and ALB, with ABS plug at the front, with connecting cable Caution: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrics 12-24 volts, multi-chamber LED lights, yellow LED lighting on the side, license plate lighting in LED, (Note! Incorrect diagnoses can occur with certain towing vehicles, although the function is present) 2 white position lights at the front in LED 2 white/red lane keeping lights at the rear in LED 2 x 7-pin, interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (light removable) 2 pairs of warning signs with double LED lighting and extendable