Flatbed semitrailer

4x FLIEGL SDS 380

Condition: new, empty load weight: 11,000 kg, maximum load weight: 27,000 kg, overall weight: 38,000 kg, axle configuration: 2 axles, loading space length: 7,300 mm, loading space width: 2,550 mm, tire size: 235/75 R17.5, color: grey, operation weight: 11,000 kg, Equipment: ABS, Chassis: -Steel frame welded construction with front and rear frame offset and low bed without rear bevel -Frame neck + fifth wheel plate 225 mm -Low bed designed for point load 25 tonnes over 5 m -Outer frame closed on the outside with welded-in tie rings for lashing -Replaceable 2" king pin -Rear suspension rail for aluminium ramps Axles and tyres: -BPW low-loader axles, 10 tonnes axle load each, bellows diameter 360 mm -Air suspension with lifting and lowering device, stroke 220 mm (-60/+160 mm) -Wabco SmartBoard with ECAS function for 2 coupling heights + 100 mm -S-cam brake 300/200 mm, asbestos-free brake pads -Automatic slack adjuster -IVTM tyre pressure monitoring -9 tyres 235/75 R 17.5, tubeless Steering: -1. and 2nd axle hydraulically forced-steered via fifth wheel coupling Floor: -Multi-layer glued plate floor with a thickness of 27 mm flush with the outer frame and longitudinal beams -Reinforced at the bottom with GRP coating -12 pairs of binding rings welded into the outer frame (8 pairs of RUD 8 ton - 6 pairs in the low bed and one pair each on the gooseneck and at the beginning of the rear unit - 2 pairs of 4 ton lashing rings each on the gooseneck and rear unit) -6 pairs of mushrooms in the outer frame in the low bed -Storage compartment with lid in the floor of the low bed at the front left and right Front wall: -25 mm aluminum hollow profiles raised up to the lower edge of the roof with integrated tarpaulin tensioning device Sliding tarpaulins: -Sliding tarpaulins on both sides with welded vertical and horizontal straps (distance approx. 600 mm) and tension fasteners made of stainless steel -Adjustable tarpaulin straps (over dead center) up to loading width of 4,000 mm including tarpaulin extension with press studs and Velcro fastener -Tarpaulin extension in direction of travel: 300 mm, height: 750 mm -Incl. Eyelets for loose tarpaulin extension part -1 pair of vertical tarpaulin pockets with a length of approx. 1,000 mm, position in the low bed at the front bend -With belt pockets Rear wall: -Steel rear portal frame with side tarpaulin attachment device -Aluminium double-wing door, 25 mm thick -Both door wings can be fully folded over with door stop -One aluminium double-joint hinge and two recessed grip recesses per door wing Corner pillars at the front: -At roof height, screwed on to the front Central pillars: -3 pairs of continuously adjustable folding pillars -The pillars can be moved along the entire length using a trolley -Central pillars in the low bed can also be fixed in the rear platform Roof: -EDSCHA sliding roof (galvanised) with crossbars that can be moved in both directions (pushed together towards the front in the loading space) Bdsdpfsiu Eu Nsx Ap Ioc -Rear portal crossbeam can be swung away -PVC tarpaulin roof without customs seal -Hand hydraulic lifting roof on both sides, lifting 450 mm -Lifting roof can be moved in the positions at the front (9x50) and rear (9x50) -Including tarpaulin extension and tarpaulin flap at the rear -Canopy at the very front of the bulkhead can be cranked out 900 mm each Accessories: -Extendable warning signs (removable at the front and rear with socket) including position lights up to a loading width of 4,000 mm -Storage of the 4 warning signs on the inside of the front wall, top right and left -1 aluminum ladder with bracket 2,500 mm long on the front wall -2 rows of aluminum slats attached in a self-locking manner -Sheet metal mudguard with mud flaps -1 night parking sign and 1 ADR

Condition: new, maximum load weight: 36,156 kg, overall weight: 45,000 kg, axle configuration: 3 axles, Year of construction: 2026, MAX200-N-3A-13.60-19.5-2.54 Technical data Speed: 80 km/h Total weight: 45,000 kg Fifth wheel load: 18,000 kg Axle load: 27,000 kg Empty weight (+/- 3%): 8,844 kg Payload approx.: 36,156 kg Loading area length: 13,600 mm Fifth wheel height loaded: 950->1,050 mm Rear steering radius: 2,300 mm Extendable by: 3,400 mm Axle spacing: 1,360/1,405 mm Total width: 2,540 mm Technical description Loading area: Loading area in extendable design with pneumatically operated locking. 2 pairs of lashing rings (LC 5,000 daN). 1 pair of lashing rings (LC 10,000 daN). 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN). 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). Cut-outs in the outer frame of the loading area for hanging tensioning straps. (LC 2000 da N) Seat supports: JOST seat supports (mechanical) with 2-speed gearbox for 24t lifting load (50t test load). Axles: SAF axles: SAF axles CD, air-sprung, with disc brakes (377 mm), with lifting/lowering function. (ET 120). The self-steering axles with electro-magnetic reversing lock can be activated via reverse gear or manually. Axle tool. (± 80kg) Braking system: Braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel construction: Steel construction made of high-strength fine-grain steels. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) top coat in a single color in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint possible. Electrical system: Electrical system in accordance with EU regulations, lighting LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15-pin. Connection in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included Yellow-red air couplings on the galvanized front connection panel. 2 pieces of brake shoes with holder. 2" kingpin A galvanized steel bulkhead approx. 2200 mm high. (± 105kg) EN12642-XL Yellow reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer. European reflector signs (red-yellow) on the rear of the trailer. Loading area with approx. 38 mm thick hardwood floor. (± 320kg) 10 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area. (± 30kg) 1 spare wheel holder under the loading area on the right in the direction of travel. Tires 435/50 R 19.5 as selected by the manufacturer. A mud flap ( ) on the rear of the trailer. Manual and description on USB stick. A bracket for a rotating beacon on the rear of the trailer. Bodpfxeg Sk Tvo Ap Iodc One bracket for a rotating beacon on the gooseneck and on the rear panel on the left and right the warning signs including a socket. An INOX toolbox across the loading area. (1000x400x2500) (± 135kg) 6 pairs of WADER container pockets in the loading area, for 1x20' container, 2 x 20' container or 1 x 40' container, an additional locking point is provided in the pull-out for a 45' container. (± 90kg) 4 pairs of WADER container locks. (± 60kg) 10 pairs of galvanized plug-in stanchions approx. 100 x 50 mm, 1,000 mm high. (± 220kg) 3 pairs of stanchion pocket strips, mounted across the loading area, for plug-in stanchion

Condition: new, empty load weight: 10,000 kg, maximum load weight: 41,600 kg, overall weight: 51,600 kg, axle configuration: 3 axles, loading space length: 13,600 mm, loading space width: 2,540 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Loading area: -Gooseneck, length approx. 4,100 mm with central support -Loading area in extendable design, length approx. 9,500 mm with bevel at the rear approx. 350 mm x 10° and integrated hanging bar for attaching loose aluminum loading ramps -Pneumatic locking with conical locking bolts and reinforced locking positions -The supply lines are protected in the extendable supports and automatically adjust to the respective loading area length Axles, suspension and tires: -BPW axles and suspension, all axles hydro-mechanically forced steered -Mounted on a turntable -Technical axle load: 12,000 kg -Air suspension with raising and lowering valve -Tires 235/75 R17.5 twin tires Paint: -6-K final treatment -Complete Steel construction shot blasted after welding -One layer of zinc-based base paint, one layer of primer -Final coating with 2 layers of 2-component paint (acrylic) in one color in MB 7350 Nova gray, then sealing of the cavities with special wax Steel construction: -Steel construction made of high-strength fine-grain steel -Steel qualities: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) -Welder tested according to DIN-EN 287-1 -MAG welding process according to EN ISO 4063, M21 protective gas according to EN ISO 14175 Accessories: -Front wall made of steel, approx. 1,600 mm high -Round NATO socket on the front connection strip -3 kW electro-hydraulic unit for controlling the Hydraulic processes -4 pairs of recessed lashing rings in the outer frame of the gooseneck -4 pairs of stake pockets embedded in the outer frame of the gooseneck, for stakes approx. 100x50 mm -1 stake pocket strip mounted transversely in the loading floor of the gooseneck, for stakes approx. 100x50 mm (1x at the back of the gooseneck) -2" king pins -Mechanical seat supports with 2-speed gearbox and crank -JOST module B - static test load = 50,000 kg -Approx. 32 mm wooden floor on the gooseneck and the loading area, framed in ALU omega profiles -A locking point on the extension, approx. every 500 mm -10 pairs of recessed lashing rings lying in the outer frame of the loading area, foldable outwards -6 pairs of stake pockets embedded in the outer frame of the loading area, for stakes approx. 100x50 mm -2 stake pocket strips mounted across the loading floor of the loading area, for stakes approx. 100x50 mm -Inox toolbox approx. 1,250 x 500 x 550 mm -Bevel on the vehicle's end crossbar, approx. 350 mm 10° -Integrated hanging strip for loose aluminum docking ramps on the vehicle's end crossbar -1 pair of downpipe supports on the end crossbar -Fenders on all axles Bdsdpfoiuy Nlox Ap Isc -Central lubrication system with 1 pump -Steering can be operated from the front and rear using a cable remote control via push button, with alignment control of the axles -Under the gooseneck and at the back of the end crossbar, a 7-pin socket for warning signs on the left and right -A 7-pin socket on the end crossbar -Container locks "TWIST-LOCKS" in the loading area for transporting 2x 20ft - and 1x 40ft containers -Radio remote control for the steering in addition to the cable remote control, with 2 indicator lights on the receiver as a lane control -2 axle load gauges + axle load diagram -4 warning signs approx. 423 x 423 mm extendable by approx. 400 mm -Standard HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% -

Condition: new, maximum load weight: 30,540 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 13,550 mm, loading space width: 2,550 mm, loading space height: 2,990 mm, total width: 2,550 mm, total height: 1,010 mm, Year of construction: 2025, Equipment: ABS, SCHWARZMÜLLER 3-AXLE FLATBED SEMITRAILER RH100 – EXTENDABLE – For Building Material and Construction Machinery Transport, NEW VEHICLE GVW (technical): 39 t Axle load (technical): 27 t Fifth wheel load (technical): 12 t Kerb weight approx. 9 t (+/- DIN tolerance) Flatbed length approx. 13,500 mm = front approx. 4,150 mm, rear approx. 9,350 mm Flatbed width approx. 2,540 mm Loading height front approx. 1,060 mm at kingpin height approx. 980 mm; rear 1,010 mm Extendable lightweight welded steel frame construction Extension length approx. 4,000 mm, lockable at intervals of approx. 500 mm Reinforced design for building material transport: 20 t/5m at the center of gravity, machinery transport up to 20 t (retracted) Reinforced U-profile outer frame 6 mm Tapered crossmembers 4 mm Bdsdpewfu N Rjfx Ap Isc Rear frame bevel, approx. 15°, approx. 500 mm Visual indicator for pneumatic frame lock on both sides, with Green control lamp = indicator light for pneumatic frame lock at Front left of the trailer Energy drag chain in the central frame Frame lock with integrated grease strip 4 pairs of extendable 8 t lashing rings, rear 9 pairs of extendable 10 t lashing rings in the outer frame profile, foldable outwards on both sides for oversize securing 10 pairs of lashing mushrooms with welded round bar under the outer frame 6 pairs of insert pockets with reinforced brackets for box section stanchions 80x50x5 mm (longitudinal, approx. 3 mm clearance), on both sides of the outer frame 3 insert pocket cross-members for box section stanchions 80x80 mm, at central beams Insert pocket cross-members as empty holders for box section stanchions 6 pairs of recessed container locks for: 2 x 20 ft containers 1 x 20 ft container centered 2 x 20 ft containers 1 x 30 ft container Reinforced rear end plate with continuous rail for loading ramps Manual 2 x 12 t landing gear, single side operation + load equalizer 2 drop-down support feet at the rear SAF Intradisc B9 axles with disc brakes ø370 mm (19.5" disc), Load capacity 9 t/axle, on-road design Axle spacing 1,310 + 1,410 mm Wheelbase 7,650 mm Self-steering SAF trailing axle, approx. 10° steering angle, electrically pneumatic reverse lock activated automatically in reverse, additionally for cab switch with release valve Special axle lift on 1st axle, lifts/lowers automatically depending on weight, with forced lowering, starting aid button in cab / "3 x braking" Odometer 6x tires 435/50 R 19.5, 164J 6x steel rims 14.00 x 19.5 Braking system EU Directive 71/320 ECE R13 2-line air braking system, EBS 2S2M, one axle monitored RSS/RSP stability program Spring-actuated parking brake Steel air tanks Air suspension with lift/lower function, total stroke approx. 200 mm Automatic ride height at 15 km/h Quick release valves SWIT – Schwarzmüller Intelligent Telematics, service package “BASIC” Axle load display EBS-CAN bus signal Tire pressure monitoring per ECE Directive 141 35 mm wooden floor, laid lengthwise, steel chequer plate covers over wheels Wooden floor impregnated on both sides Reinforced steel front wall approx. 1,800 mm + center posts integrated in front wall 2 lashing eyes in upper corner posts Front steel corner posts integrated in front wall (full side loading length) 24-volt lighting system according to EU Directive 76/756/EEC 2 full LED multi-chamber tail lights “Aspöck” with integrated control unit Flashing LED side marker lights

Condition: used, maximum load weight: 7,350 kg, overall weight: 10,500 kg, axle configuration: 2 axles, first registration: 05/2011, loading space length: 5,000 mm, loading space width: 2,440 mm, loading space height: 900 mm, total width: 2,550 mm, Gross weight: 10,500 kg Unladen weight: 3,150 kg Bdodexnhm Sspfx Ap Ijc Payload: 7,350 kg Overall length: 6,920 mm Loading length: 5,000 mm Width: overall width 2,550 mm / platform width 2,440 mm Loading height: approx. 900 mm Further information - Height-adjustable drawbar - 500 mm foldable sidewalls - Support legs

Condition: excellent (used), first registration: 03/2021, Year of construction: 2021, Equipment: ABS, = Additional options and equipment = - ADR - Air suspension - Central lubrication = Further information = Unladen weight: 12,360 kg Payload: 43,140 kg Gross vehicle weight: 55,500 kg Bsdpfsy E Hdmsx Ap Isdc Loading platform height: 138 cm Technical condition: very good Visual condition: very good Price: On request

Condition: new, maximum load weight: 36,565 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 13,550 mm, total width: 2,550 mm, total height: 1,040 mm, Year of construction: 2025, Equipment: ABS, Brand new Kässbohrer SPS Mega heavy-duty platform trailer available immediately! Technical data: * Fifth wheel height: 950 mm * Platform length: 13,550 mm * Gooseneck: 120 mm * Platform height: 1,040 mm * Wheelbase: 7,700 mm * Axle spacing: 1,360 mm * Total width: 2,550 mm * Technical total weight [80 km/sa] 45,000 kg * Technical total weight [60 km/h] 46,000 kg * Empty weight: 7,827 kg Chassis: * BPW axles with air suspension and disc brakes * Air suspension with load gauge * 1st axle can be lifted * Wabco braking system * Tires 445/45/R 19.5 Chassis: * Chassis, made of high-quality and high-strength S700 MC steel, in accordance with ISO 1726 * 2 mm Omega profile reinforced 30 mm hardwood floor * 8x2 units of side extensions extendable up to 300 mm * Support winch at the front, foldable supports at the rear Ramp: * Mounts for ramps at the rear of the vehicle * Ramp storage box at the rear Load securing: * Lashing rings * Stake pockets * 6 x 2 pcs. container locking pockets (suitable for 1x20 ft., 2x20 ft., 1x40 ft. containers) + 2 x 2 pcs. container locks * Front wall made of steel material with a height of 1,500 mm with Code XL certificate Bdedpfx Aperukuro Ioc Accessories: * 1x stainless steel tool box * Stake box Chassis color: RAL 3020 traffic red We are happy to provide you with further information

Condition: new, maximum load weight: 36,565 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 13,550 mm, total width: 2,550 mm, total height: 1,040 mm, Year of construction: 2025, Equipment: ABS, Brand new Kässbohrer SPS Mega heavy-duty platform trailer available immediately! Technical data: Bdodpfx Asrukt Rsp Ijc * Fifth wheel height: 950 mm * Platform length: 13,550 mm * Gooseneck: 120 mm * Platform height: 1,040 mm * Wheelbase: 7,700 mm * Axle spacing: 1,360 mm * Total width: 2,550 mm * Technical total weight [80 km/sa] 45,000 kg * Technical total weight [60 km/h] 46,000 kg * Empty weight: 7,827 kg Chassis: * BPW axles with air suspension and disc brakes * Air suspension with load gauge * 1st axle can be lifted * Wabco braking system * Tires 445/45/R 19.5 Chassis: * Chassis, made of high-quality and high-strength S700 MC steel, in accordance with ISO 1726 * 2 mm Omega profile reinforced 30 mm hardwood floor * 8x2 units of side extensions extendable up to 300 mm * Support winch at the front, foldable supports at the rear Ramp: * Mounts for ramps at the rear of the vehicle * Ramp storage box at the rear Load securing: * Lashing rings * Stake pockets * 6 x 2 pcs. container locking pockets (suitable for 1x20 ft., 2x20 ft., 1x40 ft. containers) + 2 x 2 pcs. container locks * Front wall made of steel material with a height of 1,500 mm with Code XL certificate Accessories: * 1x stainless steel tool box * Stake box Chassis color: RAL 3020 traffic red We are happy to provide you with further information

Condition: good (used), axle configuration: 3 axles, permissible axle load (axle 1): 9,000 kg, permissible axle load (axle 2): 9,000 kg, permissible axle load (axle 3): 9,000 kg, first registration: 05/2019, total length: 13,700 mm, total width: 2,550 mm, wheelbase: 9,400 mm, color: black, Year of construction: 2019, Equipment: ABS, = Additional options and equipment = - Air suspension = Further information = Axle configuration Rear axle 1: Lift axle; Max. axle load: 9,000 kg Rear axle 2: Max. axle load: 9,000 kg Rear axle 3: Max. axle load: 9,000 kg Weights Unladen weight: 6,160 kg Payload: 32,840 kg Gross vehicle weight (GVW): 39,000 kg Functional Loading platform height: 132 cm Condition Technical condition: good Visual condition: moderate Financial information Price: On request Further information Please contact David F Middelman for more information. Bodpfxjyx Ducs Ap Iedc

Condition: good (used), machine/vehicle number: SKBS40S30RKE27851, axle configuration: 3 axles, loading space length: 13,550 mm, loading space width: 2,550 mm, loading space height: 900 mm, Year of construction: 2024, = Additional options and equipment = - Rear air suspension - Front air suspension Bdsdpeyagk Uofx Ap Ijc - Disc brake system = Further information = Weights Unladen weight: 7,070 kg Payload: 35,930 kg Gross vehicle weight: 43,000 kg Condition Technical condition: good Visual condition: good Further information Front tyre condition: 50 Front tyres: 265/70 R 19.5 Rear tyres: 265/70 R 19.5 Last inspection: 2026-01-15 Further information Please contact Lastas Sales for more information.