Low loader semitrailer

BROSHUIS 3ABSD-48 3-Achs Semi-Tieflader 2-fach Teleskop S

Condition: new, empty load weight: 11,000 kg, maximum load weight: 27,000 kg, overall weight: 38,000 kg, axle configuration: 2 axles, loading space length: 7,300 mm, loading space width: 2,550 mm, tire size: 235/75 R17.5, color: grey, operation weight: 11,000 kg, Equipment: ABS, Chassis: - Steel frame welded construction with front and rear frame extensions and a low-bed without a rear slope - Frame neck + kingpin plate 225 mm - Low-bed designed for a point load of 25 tons over 5 m - Outer frame closed on the outside with welded lashing rings for securing cargo - Interchangeable 2" kingpin - Rear mounting rail for aluminum ramps Axles and Tires: - BPW low-loader axles, 10 tons axle load each, air spring diameter 360 mm - Air suspension with lifting and lowering device, stroke 220 mm (-60/+160 mm) - Wabco SmartBoard with ECAS function for 2 coupling heights + 100 mm - S-cam brake 300/200 mm, asbestos-free brake linings - Automatic slack adjusters - IVTM tire pressure monitoring system - 9 tires 235/75 R 17.5, tubeless Steering: - 1st and 2nd axles hydraulically steered via the fifth wheel coupling Floor: - Multi-layer glued panel floor with a thickness of 27 mm, flush with the outer frame and longitudinal beams - Reinforced underneath with GRP coating - 12 pairs of lashing rings welded into the outer frame (8 pairs RUD 8 tons – 6 pairs in the low-bed and one pair each on the gooseneck and at the front of the rear section – 2 pairs of lashing rings 4 tons on the gooseneck and rear section) - 6 pairs of mushroom-shaped load securing points in the outer frame in the low-bed - Storage compartment with lid in the floor of the low-bed, front left and right Front Wall: - 25 mm aluminum hollow profiles extending up to the lower edge of the roof with integrated tarpaulin tensioning device Sliding Tarpaulins: - Sliding tarpaulins on both sides with welded vertical and horizontal straps (spacing approx. 600 mm) and stainless steel tensioning closures - Adjustable tarpaulin straps (over center) up to a loading width of 4,000 mm, including tarpaulin extension with snap buttons and Velcro - Tarpaulin extension in the direction of travel: 300 mm, in height: 750 mm - Incl. eyelets for a loose tarpaulin extension part - 1 pair of vertical tarpaulin pockets with a length of approx. 1,000 mm, position in the low-bed at the front extension - With strap pockets Rear Wall: - Steel rear portal frame with lateral tarpaulin mounting device - Aluminum double-wing door, 25 mm thick - Both door wings can be fully folded in with door latch - One aluminum double-hinge hinge and two recessed handle recesses per door wing Front Corner Posts: - At roof height, screwed on at the front end Intermediate Posts: - 3 pairs of steplessly adjustable folding posts - The posts can be moved along the entire length using roller carriages - Intermediate posts can also be fixed in the rear platform in the low-bed Roof: - EDSCHA sliding tarpaulin (galvanized) with crossmember that can be moved in both directions (pushed forward together in the loading area) - Rear portal crossbar can be swung out - PVC tarpaulin roof without customs closure - Manually hydraulic lifting roof on both sides, stroke 450 mm - Lifting roof can be operated in the front (9x50) and rear (9x50) elevated positions - Including tarpaulin extension and tarpaulin rail at the rear - Tarpaulin can be extended by 900 mm at the front end wall Accessories: - Extendable warning signs (removable at the rear and front with socket) incl. position lights up to a loading width of 4,000 mm Cjdjiu Eu Njpfx Aafjri - Storage of the 4 warning signs on the front wall, inside, top right and left - 1 aluminum ladder with bracket 2,500 mm long on the front wall - 2 rows of aluminum slats self-locking - Sheet metal mudguard

Condition: good (used), functionality: fully functional, empty load weight: 7,200 kg, maximum load weight: 31,800 kg, overall weight: 39,000 kg, axle configuration: > 3 axles, first registration: 10/2019, loading space length: 13,700 mm, loading space width: 2,550 mm, loading space height: 800 mm, suspension: air, tire size: 235.75 r 17.5, color: traffic orange, Year of construction: 2019, Equipment: ABS, Moeslin low-bed semi-trailer with gooseneck, used, with ramps, 3 axles with 3rd steering axle, air suspension, EBS, prepared for removable rear ramps, 120 cm front headboard, 5 ton side RUD collar hooks, twist locks for 20+20, 40 and 45 ft containers, 3 through cross-members for stanchion seats, 2 PVC toolboxes, ground clearance 84 cm, year 2019. Dealer: INTERDRIVE SRL-PARMA. Credpjxnqvcofx Aafsi

Condition: used, first registration: 01/2012, * Tarp superstructure * !!!Not a low loader!!! * Coil trough * Tarp * Superstructure * Variable tarp superstructure for low loaders * Removable * Immediately available * Subject to errors and prior sale Do you have any questions? Contact us for quick advice, also directly via WhatsApp: We offer: Net purchase for companies from the EU with VAT ID number as well as customers from third countries. Csdpfxerqtqmj Aaferi Leasing and financing options. Handling of all customs formalities. Issuance of short-term and export license plates. Transport to port. All prices listed on Kleinanzeigen are gross prices and already include the legal VAT of 19%.

Condition: used, maximum load weight: 36,515 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 05/2023, next inspection (TÜV): 05/2027, Equipment: ABS, Excerpt from Equipment List: Gooseneck: Gooseneck with front corners angled approximately 45° and rear taper of approximately 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood decking approximately 30 mm thick. Extendable Loading Platform: Extendable loading platform with rear taper of approximately 1,000 mm x 8°. 5 pairs of lashing rings that fold outwards (LC 5,000 daN). 3 pairs of lashing rings that fold outwards (LC 10,000 daN). 1 pair of lashing rings lying horizontally at the front of the loading platform (LC 10,000 daN). Hardwood decking approximately 48 mm thick, with diamond plate decking over the axles. Axles: BPW axles and suspension, all axles with hydro-mechanical forced steering. Technical axle load: 12,000 kg each. Air suspension with lifting and lowering valve. Axle tool. Tires: Tires 245/70 R 17.5 3PMSF, load index (146/146 F) - manufacturer of our choice. Kingpin: JOST kingpins (mechanical) with 2-speed gearbox for approximately 24 t lifting capacity (approximately 50 t test load). Braking System: Braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Paintwork: First-class and durable corrosion protection of the standard shot-blasted welded frame is guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) topcoat, solid color in RAL 3002 carmine red. Rear section metallized and painted in RAL 9010 (pure white). Metallic paint is not possible. Csdszqiiajpfx Aafjri Steel Structure: Steel structure made of high-strength fine-grain steels. Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Electrical System: Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the connection bar at the front with sockets 24N, 24S & 15-pin. Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Includes the following additional equipment: - 2-inch kingpin - One galvanized steel front wall, approximately 400 mm high. - Yellow-red air couplings on the galvanized connection bar at the front. - 4 wheel chocks with holder on the front wall (± 5kg) - One spare wheel holder in front of the front wall. - Electro-hydraulic unit (± 45kg) - Steering from the front and rear by means of a cable remote control with push buttons, with single-axle steering control (without installation in the tractor unit) - Mounting in the rear area of the gooseneck for aluminum loading ramps. - European reflector signs (red-yellow) on the rear of the trailer. - Yellow reflector tape according to EU regulations on the side, on the extendable section and at the rear of the trailer. - On the gooseneck and on the rear panel, one holder on the left and right for warning signs including socket. - One holder for a rotating beacon on the rear of the trailer. - Galvanized folding supports under the taper of the loading platform. - One mud flap on the rear of the trailer. - Manual and description on a USB stick. - Speed stickers 80 km/h on the rear and on both sides. - Load measuring device for determining the axle loads including load chart.

Condition: used, overall weight: 11,500 kg, first registration: 12/1994, Structure: Crjdozix Rqjpfx Aafji Very good condition, fully extendable to a total length of 18.5 m.

Condition: used, axle configuration: 3 axles, permissible axle load (axle 1): 9,000 kg, permissible axle load (axle 2): 9,000 kg, permissible axle load (axle 3): 9,000 kg, first registration: 10/2005, total width: 2,530 mm, suspension: air, Equipment: ABS, = Additional Options and Accessories = - Air suspension - Central lubrication system = Additional Information = General Information Year of manufacture: 2005 Axle Configuration Suspension: Air suspension Rear axle 1: Max. axle load: 9,000 kg Rear axle 2: Max. axle load: 9,000 kg Rear axle 3: Max. axle load: 9,000 kg Weights Unladen weight: 9,500 kg Payload: 32,500 kg GVW: 42,000 kg Cedpow S Dnhsfx Aafsri Functional Features Extendable body: Yes Financial Information Price: On request Further Information Please contact David F. Middelman for more information.

Condition: used, mileage: 517,000 km, power: 338 kW (459.55 HP), first registration: 11/2002, fuel type: diesel, overall weight: 18,000 kg, brakes: retarder, gearing type: mechanical, emission class: euro3, Equipment: crane, soot filter, Crane: ----- Retarder - air conditioning - leaf suspension - Hiab 166-4 - top condition Cedjy Sww Repfx Aafori Suspension: Leaf suspension

Condition: good (used), functionality: fully functional, maximum load weight: 18,000 kg, overall weight: 48,000 kg, Year of construction: 2000, Manufacturer: Goldhofer Cjdpfx Aajz Dvq Uefjri Type: STZ-L3-35 / 3-Axle Year: 2000 Total weight: 48,000 kg Fifth wheel load: 18,000 kg Extendable from… to…: 11 m to 21.85 m

Condition: new, Crane Hiab X-HiDuo 138DS-3 HIDUO – The intelligent workhorse Work light – LED version Crjdpfx Aaoyntk Rjfji CE safety basic equipment, EU-compliant – with CE certificate Control system with 3 hydraulic circuits Elevated platform on the left, valve at the bottom of the crane base, for remote control Bilateral control device, electronics system – SPACE X4 – one interface each arranged on the left and right sides, 24V DC The XSDrive piano remote control can be operated wirelessly or via cable The invisible OPS safety cabin The D-joint has a lever connection between the boom and lifting arm (knee joint). 2m = 4700 kg 5m = 2600 kg 7m = 1800 kg 9m = 1340 kg 11m = 1060 kg = Further information = Year of manufacture: 2023 Design year: 2023 General condition: very good Technical condition: very good Optical condition: very good

Condition: new, overall weight: 80,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, More vehicles available. Excerpt from the equipment list below. Full equipment details on request. GOOSENECK: * Gooseneck in SNT design, optimized for loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * Suitable for tractors: 4 x 2, 6 x 2, and 6 x 4 * Detachable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX at the front connection rail with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic unit for controlling all hydraulic functions except hydraulic winches * Gooseneck outer rail with mounting holes for screwable lashing rings. First hole approx. 200 mm from front, then approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings at rear part of gooseneck (LC 10,000 daN) * On the gooseneck: 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized finish * On the gooseneck: 1 plug-in aluminum rear wall, approx. 400 mm high, anodized finish * Approx. 40 mm hardwood floor covering on gooseneck, checker plate covering over kingpin * 3.5-inch kingpin * Gooseneck guide plate for the fifth wheel, approx. 500 mm wide * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) * 2 pairs of lashing rings with retention spring hanging on the outer rails of the gooseneck (LC 5,000 daN) Codsxarmajpfx Aaferi LOADING PLATFORM: * Extendable loading platform, length approx. 8,800 mm with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical lock bolt and reinforced locking positions; supply lines routed securely inside the extendable rails, automatically adapting to the current platform length * BPW axles and suspension; 1st axle steerable, all others force-steered via hydro-mechanics * 1st axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lifting/lowering valve * 235/75 R 17.5 3PMSF twin tires – brand at our discretion * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B – static test load 50,000 kg * Full-length hardwood floor, interrupted between axles, approx. 50 mm thick (increases slip resistance). – Long slots for removable and repositionable bridging elements * At the front of the platform – 1 movable intermediate table, approx. 300 mm wide, for the large-cross-section sliding tube, with checker plate covering. – Front and rear with long slots for removable and repositionable bridging elements * 1 pair of lashing rings on front cross member (LC 10,000 daN) * 7 pairs of flush-mounted, fold-out lashing rings in the outer frame of the platform (LC 10,000 daN) * Extendable (galvanized) widened sections, approx. 230 mm per side (without wooden planks) * 1 pair of mechanical rear supports * Rear steering operable from front and rear via cable remote control, with single-track control of axles, without installation on the tractor * TPMS tire pressure monitoring sensors fitted to all wheels * Deck locking with conically welded locking profiles every 500 mm * Lock monitoring left and right on the trailer * Mechanical lock for intermediate table (approx. 300 mm wide) to secure the table when extended * 5 pairs of threaded blocks mounted on the extendable rail for the installation of M20 screw-in rings (LC 5,000 daN) BRAKING SYSTEM