Platform trailer

MAX Trailer Extendable / Ausziehbarer auflieger / Udtrækkelig

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. Gedpfx Asrgzv Nsdqebl GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: new, empty load weight: 15,900 kg, maximum load weight: 63,500 kg, overall weight: 68,000 kg, axle configuration: > 3 axles, loading space length: 12,700 mm, loading space width: 2,740 mm, loading space height: 860 mm, suspension: air, tire size: 235/75/r17,5, color: grey, operation weight: 52,100 kg, Equipment: ABS, Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,300 mm, rear with bevel approx. 1,000 mm x 10° Technical fifth-wheel load: 23,000 kg For SZM: 6x2, 6x4 and 8x4 Cargo bed: Loading area in extendable design, length approx. 9,400 mm with bevel at the rear approx. 500 mm x 10° A recess in the loading area and protruding into the chamfer to accommodate the excavator dipper stick approx. 3,850 x 950 x 210/290 mm Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable beams and automatically adjust to the respective loading area length Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced steered Technical axle load: 12,000 kg Air suspension with lifting and lowering valve Axle tool 235/75 R 17.5 3PMSF dual tires Load index 143/141J (144/144F) Two-piece steel ramps: A pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm Hardwood decking Hydraulically hinged ramp tips Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards Brake system: WABCO EBS-E brake system in accordance with EU regulations Sockets and lighting: 24-volt lighting system Full metallization: Complete HRM metallization with ZINACOR 850 to ensure the best corrosion protection Gbodpfemfqi Ijx Adqsl Surface treatment: Complete steel structure automatically blasted after welding with wheel blast cleaning Second blasting with corundum for optimum adhesion of the coating system Final coating with 2 layers of 2-component paint in a single color in nova grey, followed by sealing of the cavities with special wax Rims in silver gray Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: S355J2+N/S355MC S690QL/S700MC Accessories: Steel end wall, pluggable, approx. 400 mm high Connection strip for supply lines to the SZM Spiral cable for supplying the electro-hydraulic unit and/or the electric cable winch between the trailer and SZM with plug Electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches Outer beam of the gooseneck with fastening holes for screwable lashing rings The first hole approx. 200 mm from the front, then approx. every 400 mm One fastening hole in the rear upper area of the gooseneck outer beam for a screwable lashing ring Approx. 40 mm thick hardwood covering over the gooseneck, checker plate covering over the kingpin Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide Continuous, approx. 50 mm thick hardwood planking on the loading area, interrupted between the axles Locking of the cargo bed with conically welded locking profiles every 250 mm, including pretensioning plate Slotted holes for attachable and movable bridging elements: on the fixed part behind the gooseneck on the front of the cargo bed 1 movable intermediate table, for the large cross-section extension tube Control valves for the hydraulic ramps on the right-hand side of the vehicle Central lubrication system with 1 pump, with standard grease according to NLGI-2 Radio remote control for operating the steering, in addition to the cable remote control, with 2 indicator lights on the receiver as single-track control

Condition: new, empty load weight: 10,000 kg, maximum load weight: 41,600 kg, overall weight: 51,600 kg, axle configuration: 3 axles, loading space length: 13,600 mm, loading space width: 2,540 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Loading area: -Gooseneck, length approx. 4,100 mm with central support -Loading area in extendable design, length approx. 9,500 mm with bevel at the rear approx. 350 mm x 10° and integrated hanging bar for attaching loose aluminum loading ramps -Pneumatic locking with conical locking bolts and reinforced locking positions -The supply lines are protected in the extendable supports and automatically adjust to the respective loading area length Axles, suspension and tires: -BPW axles and suspension, all axles hydro-mechanically forced steered -Mounted on a turntable -Technical axle load: 12,000 kg -Air suspension with raising and lowering valve -Tires 235/75 R17.5 twin tires Paint: -6-K final treatment -Complete Steel construction shot blasted after welding -One layer of zinc-based base paint, one layer of primer -Final coating with 2 layers of 2-component paint (acrylic) in one color in MB 7350 Nova gray, then sealing of the cavities with special wax Steel construction: -Steel construction made of high-strength fine-grain steel -Steel qualities: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Gbodpfoiuy Nlox Adqol -Welder tested according to DIN-EN 287-1 -MAG welding process according to EN ISO 4063, M21 protective gas according to EN ISO 14175 Accessories: -Front wall made of steel, approx. 1,600 mm high -Round NATO socket on the front connection strip -3 kW electro-hydraulic unit for controlling the Hydraulic processes -4 pairs of recessed lashing rings in the outer frame of the gooseneck -4 pairs of stake pockets embedded in the outer frame of the gooseneck, for stakes approx. 100x50 mm -1 stake pocket strip mounted transversely in the loading floor of the gooseneck, for stakes approx. 100x50 mm (1x at the back of the gooseneck) -2" king pins -Mechanical seat supports with 2-speed gearbox and crank -JOST module B - static test load = 50,000 kg -Approx. 32 mm wooden floor on the gooseneck and the loading area, framed in ALU omega profiles -A locking point on the extension, approx. every 500 mm -10 pairs of recessed lashing rings lying in the outer frame of the loading area, foldable outwards -6 pairs of stake pockets embedded in the outer frame of the loading area, for stakes approx. 100x50 mm -2 stake pocket strips mounted across the loading floor of the loading area, for stakes approx. 100x50 mm -Inox toolbox approx. 1,250 x 500 x 550 mm -Bevel on the vehicle's end crossbar, approx. 350 mm 10° -Integrated hanging strip for loose aluminum docking ramps on the vehicle's end crossbar -1 pair of downpipe supports on the end crossbar -Fenders on all axles -Central lubrication system with 1 pump -Steering can be operated from the front and rear using a cable remote control via push button, with alignment control of the axles -Under the gooseneck and at the back of the end crossbar, a 7-pin socket for warning signs on the left and right -A 7-pin socket on the end crossbar -Container locks "TWIST-LOCKS" in the loading area for transporting 2x 20ft - and 1x 40ft containers -Radio remote control for the steering in addition to the cable remote control, with 2 indicator lights on the receiver as a lane control -2 axle load gauges + axle load diagram -4 warning signs approx. 423 x 423 mm extendable by approx. 400 mm -Standard HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% -

Condition: used, axle configuration: 3 axles, permissible axle load (axle 1): 9,000 kg, permissible axle load (axle 2): 9,000 kg, permissible axle load (axle 3): 9,000 kg, first registration: 10/2005, total width: 2,530 mm, suspension: air, Year of construction: 2005, Equipment: ABS, = Additional Options and Accessories = Gjdpfx Aow S Dnhsdqebl - Air suspension - Central lubrication = Further Information = Axle Configuration Suspension: Air suspension Rear axle 1: Max. axle load: 9,000 kg Rear axle 2: Max. axle load: 9,000 kg Rear axle 3: Max. axle load: 9,000 kg Weights Unladen weight: 9,500 kg Payload: 32,500 kg Gross vehicle weight: 42,000 kg Functional Extendable body: Yes Financial Information Price: On request Further Information Please contact David F Middelman for more information.

Condition: new, empty load weight: 10,600 kg, maximum load weight: 35,400 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 13,500 mm, loading space width: 2,540 mm, loading space height: 940 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Loading area: -Loading area in extendable design -Loading area with hardwood planks with rear bevel of approx. 500 mm x 8° -2 pairs of lashing rings (LC 5,000 daN) -1 pair of lashing rings (LC 10,000 daN) -6 pairs of lashing rings that can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) -Cutouts in the outer frame of the loading area for attaching tensioning straps Braking system: -Braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: -First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer -A high-quality 2-component (2K) top coat in a single color in Nova gray -Rear section metallized and in Painted RAL 9010 (pure white) -No metallic paint possible Seatposts: -JOST seatposts (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Steel construction: -Steel construction made of high-strength fine-grain steel -Steel grades: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Electrical system: -Electrical system in accordance with EU regulations, LED lighting 24 volts -2x 7-pin & 15-pin sockets Axles and tires: -BPW axles, air-sprung, with disc brakes (377 mm), with lifting/lowering function -Hydro-mechanical forced steering -Axle tool -Twin tires 235/75 R 17.5 Accessories included: -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with bracket -2" king pins -A galvanized steel front wall approx. 1600 mm high -White reflector tape in accordance with EU regulations on the side, on the extension and red at the rear -Loading area with strong hardwood floor -Steering from the front and rear using a cable -Remote control operated via push buttons, with alignment control of the axles -With radio remote control for the steering -9 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area. -Galvanized folding supports under the slope of the loading area -Movable mounting rail for aluminum docking ramps at the rear of the vehicle -European reflector signs (red-yellow) at the rear of the trailer -A mud flap at the rear of the trailer -A bracket for a rotating beacon at the rear of the trailer -A bracket for the warning signs including a socket on the gooseneck and on the rear panel on the left and right -A tool box INOX 1,500x390x810 under the loading area on the right in the direction of travel -Central lubrication system BEKAMAX (Pico) with normal grease NLHI-2 and removable protection around the pump Gbjdjl Ux Rwspfx Adqol -6 pairs of WADER container pockets in the loading area, for 1x 20ft container, 2 x 20ft container or 1 x 40ft container, an additional locking point is provided in the pull-out for a 45ft container -4 pairs Stake pocket strips, mounted transversely in the loading area, for 100 x 50 mm stakes -Lift axle on the front axle with control by TEBS -A dependency on the current axle load and the current loading status -Speed sticker 80 km/h at the rear and on both sides -Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm with an LED position light -A holder for a rotating beacon on the warning signs -Load pressure gauge for determining the axle loads including load diagram -HRM metallization (high resistance metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZIN

Condition: used, axle configuration: 3 axles, first registration: 02/2001, total length: 13,350 mm, total width: 2,550 mm, suspension: air, tire size: 245/70R17.5, color: red, Year of construction: 2001, Total length: 1,334 cm + 1,950 cm. Loading bed length: 915 cm + 1,950 cm. Loading height: 100 cm. = Further information = Axle configuration: Tyre size: 245/70R17.5 Brakes: Drum brakes Suspension: Air suspension Rear axle 1: Dual tyres; Steered; Tyre tread left inside: 30%; Tyre tread left outside: 30%; Tyre tread right inside: 30%; Tyre tread right outside: 30% Rear axle 2: Dual tyres; Steered; Tyre tread left inside: 50%; Tyre tread left outside: 50%; Tyre tread right inside: 50%; Tyre tread right outside: 50% Rear axle 3: Dual tyres; Steered; Tyre tread left inside: 30%; Tyre tread left outside: 30%; Tyre tread right inside: 30%; Tyre tread right outside: 30% Weights: Unladen weight: 15,650 kg Payload: 29,350 kg Gross vehicle weight: 45,000 kg Financial information: Price: On request Identification: Type number: 3 ABSD-48/3 / 3 x EXTENDABLE / 3 = Company information = Gedpfx Adjycf Htjqsbl ALL PRICES ARE NET FOR EXPORT. Joris Versteijnen (NL-DE-EN), Wouter Greutink (NL-DE-EN-ES-IT), Govorim po russki. We strive to provide correct information but no rights can be derived from the listed texts.

Condition: used, maximum load weight: 36,300 kg, overall weight: 45,000 kg, axle configuration: 3 axles, first registration: 02/2023, next inspection (TÜV): 03/2026, 24 month guarantee from first registration, hydraulically steered hydraulically steered Nato Stweckdose central lubrication system fifth wheel dimension 1120 - 1300 mm loading height 1340 - 1520 mm depending on fifth wheel dimension 10t lashing eyes in the edge frame spacing 1200mm excess length board remote control rotating beacon pluggable LED 220V socket extension lights 3 axle telescopic semitrailer 1x extendable up to 7500 mm (500 mm steps) loading floor 28mm hardwood 10 ton lashing eyes in the edge frame (spacing 1200 mm) stake pockets in the edge frame for stakes 81 x 5 1mm removable front wall made of steel 1800mm high Gjdpfx Ajmhd Ryodqebl