Low loader semitrailer

Schütte SAL35, Tiefbett 8,7m, 2x gelenkt, BPW

Condition: new, maximum load weight: 37,820 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. Gooseneck: - Gooseneck with beveled front corners approx. 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood floor covering approx. 30 mm thick Loading area: - 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) - Wheel recesses with square climbing slats approx. 15 x 15 mm and widenings in the lower section - Between the 1st and 2nd axles, a pair of fixed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized covers over the wheel recesses (W approx. 670 mm) – max. point load approx. 5 t/each - Recess in the chamfer and extending into the loading area for receiving the excavator bucket arm (approx. 2,900 x 750 x 210/290 mm (L x W x H)) - 1 pair of lashing rings, horizontal, at the front of the loading area (LC 10,000 daN) - 5 pairs of flip-out lashing rings (LC 5,000 daN) - 3 pairs of flip-out lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator arm recess (LC 5,000 daN) - Cut-outs in the outer frame of the loading area for securing straps (LC 2,000 daN) One-piece Steel Ramps: - One pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering - Ramp with hydraulic lifting mechanism, hydraulically adjustable - Maximum load per pair: 40,000 kg - In accordance with Regulation 1230/2012/EU, ramps with a length less than 300 mm do not count towards the vehicle length in the driving position Landing gears: - JOST landing gears (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: - BPW axles and suspension, 2 fixed axles, 1 trailing steering axle - Technical axle load: 12,000 kg each - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool kit Tyres: - Tyres 235/75 R 17.5 3PMSF – manufacturer of our choice - TPMS tyre pressure monitoring system in accordance with ECE R 141. The data transmission to the truck is via standardized EBS interface according to ISO 11992. For correct display, the truck must be able to transmit and display this data Braking system: - WABCO braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Podpfxow Tpqwe Alqjpr Steel construction: - Steel structure made of high-tensile fine-grain steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system according to EU regulations - Lighting 24 volts ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - Complete steel structure automatically shot-blasted with blasting wheel machine after welding - Second shot-blasting using corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure maximum corrosion protection - Final painting with 2 coats of two-component topcoat, single color in RAL 3002 Carmine Red, according to the RAL system 841GL - Rims in silver - Rear section metallized and in RAL 9010 (continuation see ori

Condition: new, empty load weight: 14,350 kg, maximum load weight: 53,450 kg, overall weight: 67,800 kg, axle configuration: > 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, tail-lift, Gooseneck: - Gooseneck in SNT design for optimization of loading platform length, length approx. 3,700 mm - Rear gooseneck with bevel, approx. 1,000 mm x 10° - For tractor units: 6x2, 6x4, 8x4 short Ppjdoya E A Nopfx Alqsr Loading Platform: - Extendable loading platform, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° - A recess in the loading platform and into the bevel to accommodate the excavator bucket arm, approx. 3,850 x 750 x 210/290 mm Two-Part Steel Ramps: - One pair of two-part steel ramps, length approx. 4,350 mm, width approx. 900 mm - Ramps with rubber covering - Ramps individually hydraulically movable approx. 235 mm outwards and approx. 215 mm inwards - "Super Grip" 25 mm rubber floor and steel plate floor approx. 5 mm as additional reinforcement on the platform bevel - Square climbing strips 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles, Suspension, and Tires: - BPW axles and suspension, 1st axle steerable, all other axles hydromechanically forced-steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, activatable via reverse gear and manually - Air suspension with lift and lower valve - Tires 235/75 R 17.5 - TPMS tire monitoring system according to ECE R141 - TPMS tire pressure sensors installed in all wheels including spare wheels Surface Treatment: - Complete steel construction blasted automatically with a shot blast machine after welding - Second shot blasting with corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure best corrosion protection - Final painting with 2 coats of 2K topcoat, single color in MB 7350 Novagrau Accessories Included: - Removable steel front wall, approx. 400 mm high - 3kW electro-hydraulic unit for controlling hydraulic operations, except for hydraulic winches - 1 spare wheel - Outer beam on gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of lying lashing rings at the rear of the gooseneck - 1 pair of removable ALU side walls on the gooseneck, approx. 400 mm high, anodized - 1 removable ALU rear wall on the gooseneck, approx. 400 mm high, anodized - Approx. 40 mm thick hardwood floor over the gooseneck, tread plate covering over the king pin - 2" king pin - Round NATO socket on the front connector strip - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front crossmember - 8 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards - Extensions (galvanized) extendable by approx. 230 mm per side - Wheel recesses with square climbing strips, 15 x 15 mm in front of the axles, continuously open up to the gooseneck crossmember, approx. 700 x 410 mm - Wheel recesses with square climbing strips, 15 x 15 mm between the first and second axles, approx. 1,480 x 700 x 410 mm - ALU covers for the wheel recesses, which can also be used as bridging elements for the extension or as extension beams - 1 pair of mechanical rear supports - Radio and cable remote control - Lift axle at the front axle - Square climbing strips 20 x 30 mm, approx. every 200 mm - Central lubrication system with 1 pump - Wabco Smart Board System - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Condition: new, machine/vehicle number: c78894767223a51dd199030f3, empty load weight: 4,600 kg, Further information Frame Welded steel construction made of fine-grained steel, hot-dip galvanized, flat plateau without raised edges, Loading area slanted downwards by approx. 8° after the rear axle. Side members made of steel profiles, Hot-dip galvanized steel frame, with stainless steel plate at the kink as cable guide - flush with the floor. For trucks with Wheelbase: 2nd axle 1,795 mm / 2nd to 3rd axle 4105 mm and 3rd to 4th axle 1350 mm Trailer coupling Towing hitch ball head D24.8: (height from floor to top edge approx. 480 mm), towing capacity 2,800 kg, incl. assembly and electrics with 7-pin socket Accessories/conversions 2 holders for wheel chocks, aluminum side bumpers, foldable - are taken from the truck! Steel underride guard, quarter-shell mudguards with mud flaps - will be taken from the truck! Storage box Plastic tool box, with drawer and shelf, w=650 Incl. / h=520 / d=670 mm, lockable with a padlock (lock not included). not included) 1 holder for 3 pcs. petrol cans 1 stainless steel storage box, w=600/h=400/t=500 mm, with polished door, incl. lockable, includes control valve. lockable, includes control valve and electro-hydraulic pump unit. pump unit. Control box with circumferential door seal and sealing sleeves on the back (splash-proof according to techn. technical possibility) Electrics Adaptation of the existing rear lights, 2 additional LED work lights, recessed in the bulkhead recessed switched via parking light with switch on front wall outside in FR-left, 1 LED work light, at the rear, with integrated reversing camera Incl. with color flat screen monitor, screen with suction cup mount and power supply via 24 volts, Voltage divider 24/12V, 1 socket 7-pin 12V = plug-in adapter Base Mega Grip made of toothed galvanized grating, steel grating 50/4 Incl. with mesh width 50 mm. Top side with anti-slip serration, laid continuously over the entire main frame plateau Lashing eyes 12 pairs of lashing rings suspended freely pivoting in the outer frame - 10 tons each. 1 x at the front and the last one at the rear. 1 piece Lashing eyelet at the very rear in the middle for fastening the winch cable 12 lashing eyes centrally embedded in the floor, each 5 to. (not included in Inkl. rear slope) Front wall Sheet steel bulkhead, height 1,500 mm. Fixed with corner pillars at front wall height. Each with 2 x 12 pcs. Suspension brackets for lashing chains mounted on the left and right of the front wall Cable winch Electric cable winch, 24 volt, pulling force approx. 6350 kg, mounted in the center of the bulkhead (recessed with loading bridge), operation with radio remote control, cable length min. 35 m x 9.5 mm, with roller rope window, with cable pressure plate, incl. overload protection, cable freewheel clutch, manual switch with approx. 5 m control lever, acceptance of the cable winch, civil engineer test report, test book, operating instructions Drive-on ramps Length 3,500 mm - 2-part (2,000 mm + 1,500 mm), width 850 mm, load capacity 20,000 kg / pair (also for ramp loading), electric Pjdpfx Aek Unitjlqspr for ramp loading), electro-hydraulically foldable and laterally movable - incl. Electro-hydraulic pump unit. Drive-on angle approx. 8° with lowered rear axle Ramp support made of hot-dip galvanized steel grating (like the floor of the loading bridge), with with anti-skid toothing. Ramps can be pushed together to approx. 170 mm, Hydraulic ramp extension. Ramp prepared for operation on loading ramp with full load capacity. Ramp locking with 2 tension