Low loader semitrailer

GOLDHOFER THP-ET 3+5 Kesselbett 7+5,5 m

Condition: new, empty load weight: 22,700 kg, maximum load weight: 79,300 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, loading space length: 11,000 mm, loading space width: 2,850 mm, loading space height: 920 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 22,700 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the length of the loading area, length approx. 3,750 mm, with a bevel at the rear of approx. 850 mm x 10° -Can be raised and lowered hydraulically, stroke +- 250 mm including hydraulic connection connected to the hydraulic axle compensation of the first two axles -Open in the rear third -For tractor units: 6 x 4 and 8 x 4 Loading area: -Loading area in extendable design, length approx. 11,000 mm with a bevel at the rear of approx. 500 mm x 10°. -A recess in the loading area and in the bevel to accommodate the excavator bucket handle approx. 4,240 x 900 x 440 mm -Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable supports and automatically adjust to the respective loading area length Djdsk Af Svopfx Afmjwd Ramps: -A pair of two-part steel ramps with a length of approx. 4,650 mm and a width of approx. 900 mm -Hydraulically foldable ramp tips. -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards -25 mm "Super Grip" rubber floor and approx. 5 mm sheet metal floor as additional reinforcement on the slope of the loading area -20x30 mm square climbing rails, approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: -PA-X axle system, all axles hydro-mechanically forced steered -The steering behavior of the first two axles can be optimally adjusted to the length of the loading area both mechanically and hydraulically. -Hose rupture valve on the axle compensation cylinder with automatic RESET function. -Hydraulic cylinder with shut-off valves and pins for securing in the raised position. -245/70 R 17.5 3PMSF Accessories included: -Steel bulkhead, pluggable, approx. 400 mm high -Connection strip for supply lines to the tractor unit, mounted at the height of the outer frame profile -1 spare wheel -Outer support of the gooseneck with mounting holes for screwable lashing rings -The first hole approx. 200 mm from the front, then approx. every 400 mm -2 pairs of screwable lashing rings included -Checker plate covering above the gooseneck -On the gooseneck 1 pair of pluggable aluminum side walls on the side, approx. 400 mm high, anodized -On the gooseneck a pluggable aluminum rear wall, approx. 400 mm high, anodized -3.5" kingpin / 2" kingpin mounted -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -4 Brake shoes -4 axle load gauges -Mechanical downpipe supports at the front -1 one-piece INOX tool box, approx. 2,480 x 340 x 390 mm -Mechanical downpipe supports at the front -Continuous sheet metal covering on the loading area with a painted layer of sand to prevent slipping -1 intermediate table, approx. 500 mm wide, for the pull-out, with long holes for hanging and movable bridging elements -Painted sand coating on the support surfaces of the intermediate table -Mechanical locking for locking the intermediate table to the pull-out -8 pairs of stake pockets in the outer frame -Extensions (galvanized) extendable by approx. 230 mm per side -1 pair of hydraulic. Rear supports -Central lubrication system -1 reversing light on the left and right at the rear of the vehicle -3 kW electro-hydraulic unit -Widening planks, loose, in reinforced steel U-frame -Radio and cable remote control -4 warning signs, approx. 423 x 423 mm

Condition: used, mileage: 84,860 km, power: 375 kW (509.86 HP), first registration: 02/2024, fuel type: diesel, overall weight: 18,000 kg, axle configuration: 2 axles, next inspection (TÜV): 02/2026, brakes: retarder, color: green, gearing type: mechanical, Year of construction: 2024, Equipment: ABS, air conditioning, electronic stability program (ESP), navigation system, parking heater, soot filter, Tractor Unit 4X4 Hydrodrive MAN TGX 18.510 BL SA in Full Specification First registration 02/2024 Mileage 84,860 km GM cab with 1 bunk, cab air suspension, swinging entry steps, 3-piece steel bumper, Light & Vision Plus safety package, driver comfort package, Plus interior lighting package, storage package, comfort driver’s seat with Alcantara/leather upholstery, heated and ventilated driver’s seat, rotatable Vario passenger seat, full LED lighting, LED headlights, LED fog lights, high beam assistant, automatic headlight control, 12.3-inch instrument cluster, MAN truck navigation, Climatronic air conditioning, auxiliary water heater, fridge under the bunk, 220-volt socket, ZF 16-speed manual transmission RETARDER and additionally reinforced engine brake EVBec Leaf/air suspension Wheelbase 3,600 mm, short and highly maneuverable Aluminum fuel tank 490 liters 2-line MEILLER tipping hydraulics, large aluminum hydraulic oil tank approx. 200 l, switchable high-/low-pressure system, Tyres Front axle 385/65 R 22.5 Rear axle 315/80 R 22.5 ALCOA Dura-Bright high-gloss aluminum rims Dsdswwv Urepfx Afmewd Full safety package including active steering MAN Comfort-Steering, Lane Change Support LCS and Turn Assist, side camera system SCS and 360° view assist, ACC adaptive cruise control, EBS, ABS Off-Road with additional off-road logic, emergency brake assist, emergency brake assistant EBA, Lane Departure Warning LDW, RENTING is the new BUYING—available immediately from us with full service rental.

Condition: excellent (used), functionality: fully functional, machine/vehicle number: WGOTHPE4560028329, overall weight: 102,000 kg, suspension: hydraulics, color: yellow, Year of construction: 2006, Goldhofer STHP-XLE 6 (2+4) with Excavator Bridge / Lowbed Location: D - 73230 Kirchheim unter Teck Technical specifications according to original TÜV inspection report: - Max. speed: 80 km/h - Fifth wheel load: 30,000 kg - Front axle load: 2 x 12,000 kg - Rear axle load: 4 x 12,000 kg - Gross trailer weight: 102,000 kg (at 30,000 kg fifth wheel load) - Unladen weight STHP-XLE 4 (0+4): 21.30 t / 23.50 t (incl. accessories) - Unladen weight STHP-XLE 6 (2+4): 26.70 t / 28.90 t (incl. accessories) Combination consisting of: GOOSENECK - Type XLE (Universal) - Weight: 4,500 kg - Max. fifth wheel load: 30,000 kg - Kingpin: 3.5" - Design for direct coupling of the excavator bridge or coupling of the 2-axle bogie - Central lubrication Beka-Max 2-AXLE BOGIE - Type XLE - Weight: 5,300 kg - Axle load: 12,000 kg (80 km/h) - Axle manufacturer: BPW - Tyres: 285/70 R19.5 - Chassis width: 2,750 mm - Loaded loading height: approx. 1,240 mm (+/- 300 mm) - Central lubrication Beka-Max EXCAVATOR BRIDGE / LOWBED BRIDGE - Payload: 67.75 t - Extendable: 6,000 – 14,000 mm Dwedpfewzl Nmox Afmsd - Central beam permanently mounted on rear 4-axle bogie - Claw coupling at the front - Central beam width: 1,350 mm - Inner beam width: 600 mm - Construction height: 440 mm - Loaded loading height: 650 mm (ground clearance 210 mm) - Width adjustable from 2,750 mm to 3,250 mm - Sliding tables (Weight 405 kg) - Folding widening floor panels (Weight 1,955 kg) 4-AXLE BOGIE - Type XLE - Weight: 16,110 kg incl. excavator bridge - Axle load: 12,000 kg (80 km/h) - Axle manufacturer: BPW - Tyres: 285/70 R19.5 - Chassis width: 2,750 mm - Excavator arm recess: 700 mm - Loaded loading height: approx. 1,140 mm (+400 / -200 mm) - Central lubrication Beka-Max Good condition – German vehicle from first owner – available at short notice from stock in Kirchheim unter Teck – further information on request.

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Dsdpsrgzv Nefx Afmowd Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: used, maximum load weight: 120,000 kg, axle configuration: > 3 axles, first registration: 10/1993, Year of construction: 1993, Equipment: ABS, Manufacturer: GOLDHOFER Type: THP-SL Year of manufacture: 1993 / 2010 consisting of: Dsdpjt Irxxofx Afmswd - gooseneck with hydraulic unit (year of manufacture: 1993 - hydraulics: 2003) - 2-axle chassis module (year of manufacture: 2010) - 3-axle chassis module (year of manufacture: 1993) - 4-axle chassis module (year of manufacture: 1993) - excavator bed 5.8m rigid (year of manufacture: 2010 - payload 100 tons) - excavator bed 8m + 5m extendable (year of manufacture: 1993 - payload 120 tons) Available immediately. Subject to errors and prior sale.

Condition: excellent (used), mileage: 582,537 km, fuel type: diesel, color: white, axle configuration: 10x4, fuel: diesel, brakes: retarder, driver cabin: sleeper cab, gearing type: mechanical, emission class: euro5, Year of construction: 2009, Equipment: ABS, air conditioning, cruise control, parking heater, retarder, soot filter, spoiler, = Additional Options and Equipment = - Aluminum fuel tank - Electric windows - Electrically adjustable exterior mirrors - Low-noise - Speed limiter - Refrigerator - Air suspension - Air horn - Particulate filter - Sun visor - Stability control - Auxiliary heater - Toolbox - Power take-off (PTO) - Central lubrication system = Further Information = General Information Year of manufacture: Apr. 2009 Registration number: BV-XP-06 Axle Configuration Front axle 1: Steered Front axle 2: Steered Rear axle 1: Steered Rear axle 2: Twin tires Rear axle 3: Twin tires Weights Dwsdpfsuxu Thex Afmsd Unladen weight: 36,399 kg Payload: 17,601 kg Gross vehicle weight (GVW): 54,000 kg Functional Mast: Telescopic (8 sections) Mast length: 24 m Lifting capacity: 30,000 kg Lifting height: 2,400 cm Crane: FASSI F1500AXP.28, mounted behind the cab Superstructure make: FASSI F1500AXP.28 CE Marking: Yes Condition Technical condition: Very good Visual condition: Very good Financial Information Price: On request DAF XF 105.510 10X4 Tractor Unit + FASSI F1500AXP.28 Crane EURO 5 L PACKAGE 480 HP DRIVE 10X4 WHEELBASE 570 CM AIR SUSPENSION XF SLEEPER CAB WITH AIR CONDITIONING, AUXILIARY HEATER, REFRIGERATOR MANUAL GEARBOX FIFTH WHEEL COUPLING MULTIPLE TOOLBOXES FASSI F1500AXP.28 CRANE 150 T/M CRANE!!! 2X OIL COOLER FOR CRANE HYDRAULICS 8X HYDRAULIC EXTENSIONS WORKING HEIGHT 24 METERS MAX LIFTING CAPACITY 30,000 KG MAX LIFTING CAPACITY AT 19.4 METERS 4,465 KG CENTRAL LUBRICATION SYSTEM ON THE CRANE 4X OUTRIGGERS RADIO REMOTE CONTROL FOLLOW US ON INSTAGRAM: GEURTSTRUCKS WE SPEAK GERMAN WE SPEAK ENGLISH HABLAMOS ESPAÑOL

Condition: used, overall weight: 92,000 kg, axle configuration: > 3 axles, first registration: 08/2006, loading space length: 19,000 mm, loading space width: 3,000 mm, loading space height: 815 mm, total width: 3,000 mm, Equipment: ABS, Goldhofer STZ-H6-57/80A telescopic low loader for wagon transport----                                     Approval          Technical 1 Speed:     80km/h                 65km/h Fifth wheel load:               23,000kg               26,000kg Rear axle load:       10,000kg             11,000kg Total weight:     83,000kg               92,000kg Payload:                52,500kg               61,500kg Own weight: (without accessories):           30,500kg ----Gooseneck: Length: 4,000mm Width: 2,480mm Height: 235mm Seat height: 1,350mm DLR front: 1,420mm DLR rear: 2,700mm King pin 3.5 inches Bevel: bevelled 10 degrees Corners front: bevelled 45 degrees Floor covering: spruce 50mm Seat supports: mechanical Width with side walls: 2,550mm Hydraulic STZ gooseneck with external supports, hydraulically liftable and lowerable with mechanical downpipe supports and hydraulic support cylinders hydromechanical forced steering (2-circuit steering) in flat design (height 235mm) with adjustable guide elements and THP steering cylinders. ----Loading area: Type: Platform Liftable: no Length: 13,000mm Width: 3,000mm Floor covering: sheet metal/spruce 50mm Wheel recesses: no Wider extensions: no Extendable: simply telescopic Length1: 10,000mm Loading heights (loaded) Loading height 1: 815mm Loading area telescopic, designed as an outer and inner tube construction, with 1,070mm long, fixed loading area section at the front. Bolt-link coupling integrated in the fixed loading area section for coupling boiler bridge extension supports, the square rails welded on by us serve as rail tracks in the track widths 1,000 mm (rail spacing 1,015 mm) and 1,435 mm (rail spacing 1,450 mm). Locking of the extension steps by spring-loaded cylinders and conical bushings Loading area height on the frame center tube (outer tube) approx. 815mm (+/- 130mm) Loading area height on the enclosed rail elements approx. 790mm (+/- 130mm) ----Rear chassis: Chassis type: Standard Loading height: 815mm Width: 3,000mm Wheelbase: 1,360mm Floor covering: Sheet metal Extensions: no Wheel recesses: no Excavator recess: no ----Axles: Number of axles: 6 Lift axle: see accessories Axle type: cranked steering knuckle Axle compensation: hydraulic Axle make: BPW/Eco Driving positions: 1 Axle stroke (1) +/-: 130/130mm Axle stroke (2) +/-: 0/0mm Raising/lowering valve: Yes 1st axle can be suspended pneumatically with lifting bellows ----Steering: Number of steering axles: 6 Dsdpfx Aolhn Afefmowd Steering axle arrangement: all steered Steering angle max: 45° Steering type: Hydr. 2 circles----Tires: Dimension: 235/75 r 17.5 143/141 J Tires. Type: twin Rim type: discs Rim centered: centered ----Brake code: according to EU standard: Yes AGS: Yes ALB: Yes ABS: Yes with ABS del: No Parking brake: spring-loaded EBS: No ECAS: No Remark: Brake calculation no.: GH 4324S ----Chassis remark: Steering designed for the extended state with a larger steering angle of the front axles Open wheel cutouts above the wheels with narrow cross arms in between (ALU covers see accessories below) Control elements protected on the left in the direction of travel Rims 17.5x 6.75 Cranked axles!!! ----Rear of vehicle: Design: Standard 90° Ramp fastening: see accessories Floor covering: Sheet metal Overhang from last axle: 1,300mm Support: see accessories ----Load securing: Lashing rings Number: 5 Loadable up to: 10 tons per piece Arrangement: 2 pairs on the SH                         3 pairs on the LF----Rear extension: Max. load capacity 15,000kg with a

Condition: excellent (used), axle configuration: > 3 axles, suspension: hydraulics, tire size: 245/70R17,5, wheelbase: 1,510 mm, color: red, Year of construction: 2007, = Additional Information = General Information Year of manufacture: 2007 Axle Configuration Tyre size: 245/70R17.5 Axle brand: BPW Suspension: hydraulic suspension Rear axle 1: Twin tyres; lift axle; max. axle load: 11,200 kg Rear axle 2: Twin tyres; lift axle; max. axle load: 11,200 kg Rear axle 3: Twin tyres; lift axle; max. axle load: 11,200 kg; steering axle Dodjuu Hf Hepfx Afmjwd Rear axle 4: Twin tyres; max. axle load: 11,200 kg; steering axle Rear axle 5: Twin tyres; max. axle load: 11,200 kg; steering axle Rear axle 6: Twin tyres; max. axle load: 11,200 kg; steering axle Rear axle 7: max. axle load: 11,200 kg; steering axle Dimensions Dimensions (L x W x H): 1,716 x 324 x 107 cm Weights Empty weight: 27,800 kg Payload: 117,600 kg Gross vehicle weight: 145,400 kg Functional Extendable construction: Yes Condition Technical condition: very good Optical condition: very good Damages: none Financial Information Price: On request Further Information Please contact Stefan Schaapveld for more details.

Condition: used, maximum load weight: 82,000 kg, overall weight: 126,000 kg, axle configuration: > 3 axles, first registration: 05/2009, XLE 3+5 with boiler bed hydraulic. Widenable Weights: Speed 80 km/h Fifth wheel load 30,000 kg Axle load 8 x 12,000 kg Gross gross vehicle weight 126,000 kg Unladen weight approx. 44,000 kg Payload approx. 82,000 kg Gooseneck length x width 3,756 mm x 2,480 mm Fifth wheel height (loaded) 1,300 mm Steering radius front / rear 1,300 mm / 2,800 mm Kingpin 3.5" Fifth wheel load 30,000 kg Unladen weight 4,000 kg 3-axle chassis, front single tires 285/70 R 19.5 with swing axles, 12-14 t axle load Steering: Counter-steered axle arrangement Wheelbase 1360 mm Chassis width 2750 mm Terrain weight 7,000 kg Boiler bridge: single telescopic with rear separation point, hydraulically extendable Length x width 7,000 mm x 3,000 mm, extendable to 4,300 mm Terrain extendable by 4,000 mm Overall height 450 mm Hydraulically extendable to 4,300 mm Loading height on the transformer bar: 230 mm 5-axle chassis, single tires 285/70 R 19.5 at the front with pendulum axles, 12-14 t axle load Steering: counter-steered axle arrangement Wheelbase 1360 mm Chassis width 2850 mm Terrain weight with boiler bed 32,000 kg Radio remote control Central lubrication system BPW axles ABS Djdpswcy Nwofx Afmewd Electric unit

Condition: excellent (used), color: orange, Year of construction: 2000, Colour: Orange 01 x Used Gooseneck S-THP + PPU VIN / 24739-20 Year of manufacture: 2000 01 x Used 2-Axle Module THP/LTSO 2 VIN / 21972 Year of manufacture: 1995 Width / 3,000 mm Axle load capacity / 26,000 kg per axle line Tyres / 205/65 R 17.5 01 x Used 2-Axle Module THP/LTSO 2 VIN / 21972 Year of manufacture: 1995 Width / 3,000 mm Axle load capacity / 26,000 kg per axle line Tyres / 205/65 R 17.5 01 x Used 4-Axle Module THP/LTSO 4 VIN / 21973 Year of manufacture: 1995 Width / 3,000 mm Axle load capacity / 26,000 kg per axle line Dwedpfsu Abh Tex Afmed Tyres / 205/65 R 17.5 01 x Used 4-Axle Module THP/LTSO 4 VIN / 21974 Year of manufacture: 1995 Width / 3,000 mm Axle load capacity / 26,000 kg per axle line Tyres / 205/65 R 17.5 01 x Used 4-Axle Module THP/LTSO 4 VIN / WGOTHP045W0024047 Year of manufacture: 1998 Width / 3,000 mm Axle load capacity / 26,000 kg Tyres / 205/65 R 17.5 = Further information = Year of manufacture: 2000 Width: 300 cm Technical condition: very good Visual condition: very good Price: On request Please contact Stefan Schaapveld for further information.