Low loader trailer

MÜLLER-MITTELTAL T3 Profi 3 Achsen Tieflader Rampen

Condition: used, mileage: 348,600 km, power: 375 kW (509.86 HP), first registration: 12/2017, fuel type: diesel, empty load weight: 14,500 kg, overall weight: 32,000 kg, tire size: 315/80 R22,5, axle configuration: 8x4, brakes: retarder, color: yellow, gearing type: automatic, suspension: steel-air, Equipment: ABS, additional headlights, cruise control, differential lock, low noise, parking heater, retarder, traction control, trailer coupling, Urea tank (AdBlue) Displacement 12,809 cc Rsdpfovk Un Sox Ahzeck 50 trailer coupling Hydraulics (auxiliary drive) EBS Navigation system Euro 6 C Payload 17,500 kg Automatic climate control Dautel round steel trough Hydraulic tailgate and swinging Fifth wheel plate Foldable underrun protection Sun visor Beacon lights Air + electricity for trailer operation Weights: SDAH trailer load: 18,000 kg Trailer trailer load: 55,000 kg Total train weight: 68,000 kg Tractor unit empty weight: 11,990 kg Total train weight: 64,0000 kg Errors excepted

Condition: new, empty load weight: 11,000 kg, maximum load weight: 27,000 kg, overall weight: 38,000 kg, axle configuration: 2 axles, loading space length: 7,300 mm, loading space width: 2,550 mm, tire size: 235/75 R17.5, color: grey, operation weight: 11,000 kg, Equipment: ABS, Chassis: -Steel frame welded construction with front and rear frame offset and low bed without rear bevel -Frame neck + fifth wheel plate 225 mm -Low bed designed for point load 25 tonnes over 5 m -Outer frame closed on the outside with welded-in tie rings for lashing -Replaceable 2" king pin -Rear suspension rail for aluminium ramps Axles and tyres: -BPW low-loader axles, 10 tonnes axle load each, bellows diameter 360 mm -Air suspension with lifting and lowering device, stroke 220 mm (-60/+160 mm) -Wabco SmartBoard with ECAS function for 2 coupling heights + 100 mm -S-cam brake 300/200 mm, asbestos-free brake pads -Automatic slack adjuster -IVTM tyre pressure monitoring -9 tyres 235/75 R 17.5, tubeless Steering: -1. and 2nd axle hydraulically forced-steered via fifth wheel coupling Floor: -Multi-layer glued plate floor with a thickness of 27 mm flush with the outer frame and longitudinal beams Rcsdpoiu Eu Nsfx Ahzok -Reinforced at the bottom with GRP coating -12 pairs of binding rings welded into the outer frame (8 pairs of RUD 8 ton - 6 pairs in the low bed and one pair each on the gooseneck and at the beginning of the rear unit - 2 pairs of 4 ton lashing rings each on the gooseneck and rear unit) -6 pairs of mushrooms in the outer frame in the low bed -Storage compartment with lid in the floor of the low bed at the front left and right Front wall: -25 mm aluminum hollow profiles raised up to the lower edge of the roof with integrated tarpaulin tensioning device Sliding tarpaulins: -Sliding tarpaulins on both sides with welded vertical and horizontal straps (distance approx. 600 mm) and tension fasteners made of stainless steel -Adjustable tarpaulin straps (over dead center) up to loading width of 4,000 mm including tarpaulin extension with press studs and Velcro fastener -Tarpaulin extension in direction of travel: 300 mm, height: 750 mm -Incl. Eyelets for loose tarpaulin extension part -1 pair of vertical tarpaulin pockets with a length of approx. 1,000 mm, position in the low bed at the front bend -With belt pockets Rear wall: -Steel rear portal frame with side tarpaulin attachment device -Aluminium double-wing door, 25 mm thick -Both door wings can be fully folded over with door stop -One aluminium double-joint hinge and two recessed grip recesses per door wing Corner pillars at the front: -At roof height, screwed on to the front Central pillars: -3 pairs of continuously adjustable folding pillars -The pillars can be moved along the entire length using a trolley -Central pillars in the low bed can also be fixed in the rear platform Roof: -EDSCHA sliding roof (galvanised) with crossbars that can be moved in both directions (pushed together towards the front in the loading space) -Rear portal crossbeam can be swung away -PVC tarpaulin roof without customs seal -Hand hydraulic lifting roof on both sides, lifting 450 mm -Lifting roof can be moved in the positions at the front (9x50) and rear (9x50) -Including tarpaulin extension and tarpaulin flap at the rear -Canopy at the very front of the bulkhead can be cranked out 900 mm each Accessories: -Extendable warning signs (removable at the front and rear with socket) including position lights up to a loading width of 4,000 mm -Storage of the 4 warning signs on the inside of the front wall, top right and left -1 aluminum ladder with bracket 2,500 mm long on the front wall -2 rows of aluminum slats attached in a self-locking manner -Sheet metal mudguard with mud flaps -1 night parking sign and 1 ADR

Condition: used, Year of construction: 2016, operating hours: 9,090 h, Equipment: all wheel drive, * Viewing by appointment only * Errors and prior sale excepted. Rcsdpfsx Dqmmsx Ahzek

Condition: new, empty load weight: 6,600 kg, maximum load weight: 17,400 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 6,500 mm, total length: 10,900 mm, suspension: steel, tire size: 235/75 R17,5 (Doppelbereifung), color: silver, gearing type: mechanical, fuel consumption (urban): 1,090 l/100km, Empty weight: 6600kg, permissible total weight: 24000kg, loading space length: 6,500 mmTire size: 235/75 R17.5, 1st axle: , 2nd axle: , 3rd axle: , leaf spring suspension, 3 axle low loader trailer with offset DTS-S 300 - bogie with strong ball bearing ring - foldable rear support - 1 spare wheel holder for 1 electric bike, with wheel fastening kit - 1 spare wheel, same make as basic tires, steel rim - 1 plastic tool box - extensions extendable to 3000mm (not in rear bevel) - storage compartment for wooden planks in the middle of the low load area - wooden planks 70mm for extension to 3000mm Lashing eyes low loader: - with spring jack Support axles + suspension: - SAF - drum brake axles - Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Brake system: - 2-line compressed air brake system - Spring-loaded parking brake Electrics: - 24 volt, multi-chamber lights, yellow LED lighting on the side - 1 LED rotating beacon with holder, switched via parking light (light removable) - 2 pairs of warning signs with double LED lighting and extendable to 3000 mm Floor: - Storage box embedded in the crossing slope to the crank - then with 70 mm softwood floor, steel / checker plate covering in the wheel arch area - Rear bevel with 70 mm softwood floor Loading ramps: Steel ramps 2,800 mm long, 750 mm wide, laterally movable, covered with wood - - 1 pair of ring lashing eyes embedded on the crank at the front, 10 tonnes - 4 pairs of lashing holes in the AR with 5 tonnes each for tensioning belt attachment - 7 pairs Lashing eyes at the top and sides of the outer frame, 10 tonnes each - 1 x at the front on the crank, 6 x in the low bed - 5 pairs of stake pockets in the outer frame, inside 70x40 mm (can be converted to 5 tonne ring lashing eyes for an additional charge) - 2 pairs of additional folding lashing eyes, 10 tonnes each, 1x at the front on the crank, 1x behind the 3rd axle, axles + suspension: - SAF - drum brake axles - parabolic suspension with maintenance-free steel-rubber bearings and mechanical Ac Rsdpfxotcwkrj Ahzock

Condition: new, empty load weight: 10,350 kg, maximum load weight: 39,150 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Redpfx Aoiu Er Ajhzeck Loading area: -telescopic loading area with rear slope approx. 1,000 mm x 8° -1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm -Wheel recesses with square climbing strips 15 x 15 mm and widenings in the lower area -A pair of fixed wheel recesses between the 1st and 2nd axles, approx. 1,610 x 970 x 400 mm -3-piece removable galvanized covers over the wheel recesses (W 670 mm) - max. point load 5 to / pc. -Recess in the chamfer and protruding into the loading area to accommodate the excavator dipper stick approx. 2,900 x 750 x 210/290 mm -1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) -5 pairs of lashing rings foldable outwards (LC 5,000 daN) -2 pairs of lashing rings can be folded outwards (LC 10,000 daN) -2 pairs of lashing rings in the excavator trough (LC 5,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) One-piece ALU ramps: -One pair of one-piece ALU ramps approx. 2,500 x 600 mm -Ramp with spring lifting mechanism and manually adjustable -Maximum load per pair: 24,000 kg Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 tires -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking lights -Galvanized extensions, extendable by approx. 230 mm per side -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon at the rear of the trailer -White reflector tape in accordance with EU regulations on the sides, on the pull-out and red at the rear -One bracket for the warning signs including socket on the left and right of the gooseneck and on the rear panel -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container -3 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -One removable galvanized intermediate table with 1 pair of WADER container pockets -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -a layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -A bracket for a rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, empty load weight: 6,650 kg, maximum load weight: 17,350 kg, overall weight: 24,000 kg, axle configuration: 3 axles, total length: 10,900 mm, suspension: steel, tire size: 235/75 R17,5 (Doppelbereifung), color: silver, gearing type: mechanical, fuel consumption (urban): 1,090 l/100km, Empty weight: 6650kg, permissible total weight: 24000kg, tire size: 235/75 R17.5, 1st axle: , 2nd axle: , 3rd axle: , leaf spring suspension, - steel welded construction - bogie with strong ball bearing slewing ring - foldable rear support - 1 spare wheel holder for 1 electric bike, with wheel fastening kit - without spare wheel, - 1 plastic tool box, with shelf, w620/h360/d440mm, lockable with padlock - extensions extendable to 3000mm (not in rear bevel) - storage compartment for wooden planks below the low loading area - wooden planks 70mm for extension to 3000mm - 1 pair of ring lashing eyes embedded in the front on the crank, 5 tons each - 7 pairs of lashing mushrooms embedded in the top and sides of the outer frame, 10 tons each - 1 x at the front on Crank, 6 x in the low bed - 5 pairs of stake pockets embedded in the outer frame, inside 70x40 mm - 2 pairs of additional folding lashing eyes, 10 ton each, 1x at the front on the crank, 1x behind the 3rd axle - Drawbar with 40 mm towing eye, and 8 inclined towing eyes - SAF - drum brake axles - parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (rocker compensation) - 235/75 R17.5 - steel rims in twin arrangement, factory silver - 2-line compressed air brake system - spring-loaded parking brake ABS and ALB, with plug at the front, with connecting cable - 24 volt, multi-chamber lights, yellow LED lighting on the side - 2 x 7-pin, non-interchangeable plugs at the front, with connecting cable - 1 LED rotating beacon with holder, switched via parking light (light can be removed) - 2 pairs of warning signs with double LED lighting and extendable to 3000 mm - front bend with steel/checker plate covering - storage box embedded in the crossing slope to the bend - then with 70 mm softwood floor, in the wheel arch area steel/checker plate covering - rear bevel with 70 mm softwood floor - low loading area including rear bevel 6,500 mm - steel ramps 2,800 mm long, 750 mm wide, laterally movable, covered with wood - additional ramp safety Rcedpet Szcbefx Ahzsk

Condition: used, Year of construction: 2016, operating hours: 13,250 h, CTA 962M with steering wheel with steering Condition: very good Rsdpfx Ahoi Uk N Nozsck Tires: VA 40% HA 85%

Condition: new, maximum load weight: 23,800 kg, overall weight: 30,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory with immediately and short-term available units on our website. Selection of equipment features. Full equipment specification available on request. Rcjdpfx Ahewx Dcyjzsk Weights: * Permissible gross weight: 24 t * Technical gross weight: 30 t Dimensions: * Approx. 2,100 mm = raised front platform incl. gooseneck, corners beveled * Approx. 5,350 mm = low-bed deck – level loading area * Approx. 850 mm = rear ramp slope * Overall width approx. 2,550 mm (or up to approx. 3,000 mm with extensions) * Loaded loading height approx. 870 mm * When assembling a combination, please observe the legally permitted overall height and total length. Frame: * Steel welded construction with front gooseneck and rear bevel * Rear ramp slope with central excavator shovel recess = rear recess between longitudinal beams, approx. 2,300 mm long * Integrated in the outer frame: 5 pairs of approx. 4 t lashing points (4x in the low-bed, 1x on the raised platform) * 7 pairs of recessed, pull-out 10 t lashing rings (4x in the low-bed, 1x on the ramp slope, 2x on the raised platform) * Standard ball bearing turntable Frame Attachments: * Both sides of the low-bed deck with extendable width extensions with approx. 50 mm softwood planks (track width of construction machinery to be transported must not exceed the outer frame width of approx. 2,550 mm) * 4 pairs of folding approx. 10 t lashing rings, distribution: 1 pair at the front on the raised platform, between the longitudinal beams; 1 pair at the very rear in the excavator shovel recess, left and right; 1 pair at the front of the raised platform before the gooseneck, between the longitudinal beams; 1 pair in the rear low-bed ahead of the ramp slope, in the shovel recess left + right Towing Device: * Fixed drawbar with swivel towing eye approx. 40 + 50 mm, cranked version, silent bush mounting, drawbar retaining spring with tensioner * Truck coupling height approx. 830 mm to approx. 1,030 mm * Drawbar length approx. 1,800 mm Support Device: * 2 automatic folding supports at the rear Axles: * 3 SAF air suspension low-loader axles with drum brakes * Load capacity: 11 t per axle * S-cam drum brakes approx. 300/200 mm * Automatic brake slack adjusters Wheels: * 12 tires 235/75 R 17.5, 141J, brand per factory selection * 12 steel rims 6.75 x 17.5, with preset offset, silver Brake System/Suspension: * Dual-line compressed air brake system according to ECE directive R13 * Brake system by Wabco * EBS system 4S3M, 1st and 2nd axles with sensors * RSS/RSP – stability control * Spring-actuated parking brake on 2nd and 3rd axles * Steel air tank * Brake/air supply lines with two single coupling heads, yellow/red * EBS/ABS connection cable * Retainer rubber for EBS and electrical connectors * Air suspension with lift and lowering device (rear axles only), automatic ride height adjustment from 15 km/h (RTR), front axle mechanical stop Floor: * Approx. 50 mm impregnated softwood flooring, protruding approx. 5–10 mm above upper edge of frame, steel checker plate cover over the wheels Ramps: * 2 foldable single-piece lightweight steel drive-on ramps, approx. 2,800 mm long, approx. 750 mm wide, with impregnated hardwood inserts approx. 35 mm * Ramp spacing adjustable from approx. 350 mm up to max. total width of approx. 3,000 mm * Ramps lockable in driving position by chains with tensioners * Ramp lifting aid with spiral spring * Ramps laterally adjustable manually with bar * Square ribs welded on the

Condition: used, mileage: 127,000 km, power: 309 kW (420.12 HP), first registration: 06/2020, fuel type: diesel, overall weight: 34,000 kg, axle configuration: > 3 axles, brakes: retarder, color: green, gearing type: automatic, Year of construction: 2020, Equipment: ABS, air conditioning, MERCEDES AROCS 4142 TIPPER / 8x4 Imported / Accident-FREE IN GOOD CONDITION! ? YEAR OF PRODUCTION: 2020 ? MILAGE: 127 000 km EQUIPMENT: ? ABS ? EL. WINDOWS ? AIRCONDITION ? POWER STEERING ? TACHOGRAPH Rcsdpsv Sn Sgofx Ahzek ? RETARDER CAPACITY: 20 000 kg TOTAL WEIGHT: 34 000kg TIRE SIZE: 315/80R22,5 WHEELBASE: 175/250/135 cm SUSPENSION: SPRING TEL: * KUBA - POLSKI, ENGLISH, DEUTSCH, ITALIANO * SEBASTIAN - POLSKI, DEUTSCH, ITALIANO, ????? * LASZLO - MAGYAR * COSTEL - ROMÂN? (Romana facem toate formalitatile pt export inclusiv nr) RADEK - ????? Ref. nr: 23715

Condition: used, empty load weight: 6,500 kg, maximum load weight: 23,500 kg, overall weight: 30,000 kg, axle configuration: 3 axles, first registration: 01/2008, next inspection (TÜV): 03/2024, loading space length: 8,000 mm, loading space width: 2,520 mm, loading space height: 910 mm, suspension: steel, tire size: 235/75R17.5, color: orange, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, leaf suspension, 3-axle, BPW axles, turntable, ABS (anti-lock braking system), lashing eyes, hydr. ramps, rear support, aluminum side bumpers, twin tyres, storage box Superstructure: Hydr. ramps, can be widened to 3m. BPW axles, drum brakes, lashing rings on the outside. Ramp length approx. 4000mm! ACCESSORIES WITHOUT WARRANTY, subject to alterations, prior sale and errors excepted! - . Rodpfx Ahjqpgtmjzsck