Low loader

FAYMONVILLE MAX Trailer MAX110 Semi-Tieflader

Overall weight: 63,000 kg, maximum load weight: 48,300 kg, axe configuration: > 3 axles, Condition: new, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Gooseneck * with bevelled corners at the front approx. 45° and with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area * in double extendable version with rear bevel approx. 500 mm x 8° * 5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 4 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) * 1 intermediate table approx. 250 mm * Cutouts in the outer frame of the loading area for hanging tensioning straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, above the axles Checkered plate covering Axles * BPW axles and suspension, all axles hydro-mechanically forced steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tires * 245/70 R 17.5 3PMSF, load index (146/146 F) Seat post * JOST seat posts (mechanical) with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load) Braking system * in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Paintwork * First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer * A high-quality 2-component (2K) top coat in a single color in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) Steel construction * made of high-strength fine-grain steel * Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system * in accordance with EU regulations * Lighting 24 volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15-pin connection in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Ctvjjw0A93 Incl. the following additional equipment * 2 inch kingpin * A galvanized steel bulkhead, approx. 400 mm high * Yellow-red air couplings on the galvanized connection strip at the front * 4 brake shoes with holder on the bulkhead * A spare wheel holder in front of the bulkhead * Electro-hydraulic unit * Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles (without installation in the tractor unit) * TPMS tire pressure control system in accordance with ECE R 14 * Load gauge for determining the axle loads including load diagram * Aluminum side walls and rear wall on the gooseneck, pluggable, approx. 2,440 x 400 mm (L x H) * The rear galvanized plug-in stanchions are removable (Length of the body approx. 2,560 mm) * A galvanized toolbox, integrated in the beveled gooseneck * 4 pairs of WADER container pockets in the loading area for a 20', 2x 20', 40' or a 45' container * 7 pairs of stake pockets for stakes approx. 100 x 50 mm in the outer frame of the loading area * Galvanized extensions, extendable by approx. 230 mm per side * Movable hanging rails for aluminum docking ramps at the rear of the vehicle * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * Lift axle on the front axle with control by TEBS E depending on the current axle load and the current loading condition * Central lubrication system with 2 BEKAMAX (Pico) pumps with normal grease NLGI-2, removable protection around the pumps * 2 LED reversing lights mounted at the rear * An acoustic warning si

Overall weight: 50,960 kg, maximum load weight: 37,680 kg, axe configuration: > 3 axles, Condition: new, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Gooseneck * with hardwood covering approx. 30 mm thick. Gooseneck at the rear in a straight design * 3 pairs of lashing rings (LC 5,000 daN) Loading area * in an extendable design * 5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) Dqn8Th * Cutouts in the outer frame of the loading area for hanging tensioning straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, checkered sheet metal flooring above the axles Seat supports * JOST seat supports (mechanical) with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load). Tires * 205/65 R 17.5 Axles * BPW axles and suspension * 1st axle rigid, all other axles hydro-mechanically forced steered * Air suspension with lifting and lowering valve Braking system * in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Steel construction * made of high-strength fine-grain steels * Steel qualities: S355J2+N/S355MC (yield strength 355MPa)S690QL/S700MC (yield strength 690MPa) Paintwork * First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer * A high-quality 2-component (2K) * Top coat in a single color in RAL 3002 carmine red * Rims in silver Accessories included * 2 inch kingpins * A galvanized steel bulkhead, approx. 400 mm high * Yellow-red air couplings on the galvanized connection strip at the front * 4 brake shoes with holder on the bulkhead * A spare wheel holder in front of the bulkhead * Electro-hydraulic unit * Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles (without installation in the tractor unit) * European reflector signs (red-yellow) on the rear of the trailer * Yellow reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer * A holder for the warning signs including a socket on the gooseneck and on the rear panel on the left and right * A holder for a rotating beacon on the rear of the trailer * Galvanized folding supports under the slope of the loading area * Load gauge for determining the axle loads including load diagram * 7 Pair of WADER container pockets for: 1x 20' or 1x 40' container on the loading area, 1x 40' container above the gooseneck or 2x 20' containers * Support stand with 1 pair of WADER container pockets, load capacity approx.: 20,000 kg * 7 pairs of stake pockets for stakes approx. 100 x 50 mm in the outer frame of the loading area * Galvanized extensions, extendable by approx. 230 mm per side * Movable hanging rails for aluminum docking ramps at the rear of the vehicle * 1 pair of recessed lashing rings along the central beam at the rear of the loading area (LC 10,000 daN) * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * BEKAMAX central lubrication system (Pico) with normal grease NLGI-2 and removable protection around the pump * 2 LED reversing lights mounted at the rear * One acoustic warning signal when reversing * HRM metallization (High Resistance Metallization)

Overall weight: 48,000 kg, maximum load weight: 33,865 kg, axe configuration: 3 axles, Condition: new, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Gooseneck with bevelled corners at the front approx. 45° and with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring approx. 30 mm thick * Loading area in double extendable version * Loading area in double extendable version with rear slope approx. 500 mm x 8° * 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 4 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) * 1 intermediate table approx. 250 mm * Hardwood flooring approx. 48 mm thick, checkered sheet metal flooring above the axles * Cutouts in the outer frame of the loading area for hanging tensioning straps (LC 2,000 daN) Axles * BPW axles and suspension, all axles hydro-mechanically forced steered * Technical axle load: 12,000 kg each * Air suspension with Lifting and lowering valve * Axle tool Tires * Tires 245/70 R 17.5, load index (146/146 F) Seatposts * JOST seatposts (mechanical) with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load) Braking system * Braking system in accordance with EU regulations with EBS-E (2S2M) * Without connecting lines to the tractor unit Paintwork * First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer * A high-quality 2-component (2K) top coat in a single color in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) Dqvyrv Steel construction * Steel construction made of high-strength fine-grain steel * Steel qualities: S355J2+N/S355MC (yield strength 355MPa) and S690QL/S700MC (yield strength 690MPa) Electrical system * Electrical system in accordance with EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15 pin. Connection according to ISO * 24N ISO-1185 * 24S ISO-3731 * 15-pin ISO-12098 Incl. the following additional equipment * 2" inch kingpin * A galvanized steel bulkhead, approx. 400 mm high * Yellow-red air couplings on the galvanized connection strip at the front * 4 brake shoes with holder on the bulkhead * A spare wheel holder in front of the bulkhead * Electro-hydraulic unit * Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles (without installation in the tractor unit) * Cable for supplying the electro-hydraulic unit and/or the electric cable winch (approx. 35 mm², approx. 3.5 m long, max. 250A) between the trailer and the tractor unit with plug connection (ANDERSON-ANDERSON) * Mounting in the rear area of the gooseneck for aluminum docking ramps * European reflector signs (red-yellow) on the rear of the trailer * Yellow reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer * A bracket for the warning signs including a socket on the gooseneck and on the rear panel on the left and right * Hanging rail for aluminum docking ramps at the rear of the vehicle * A bracket for a rotating beacon at the rear of the trailer * Galvanized folding supports under the slope of the loading area * A mud flap at the rear of the trailer * Manual and description on USB stick * Speed sticker 80 km/h rear and both sides * Load pressure gauge for determining the axle loads including load diagram

Overall weight: 48,000 kg, maximum load weight: 38,290 kg, axe configuration: 3 axles, Condition: new, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Gooseneck * Gooseneck with bevelled corners at the front approx. 45° and with rear bevel approx. 750 mm x 10 * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick One-piece aluminum ramps * One pair of one-piece aluminum ramps, approx. 2,500 x 600 mm, with spring lifting mechanism * Manually movable * Maximum load per pair: 24,000 kg Loading area * 1 pair of permanently installed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (LxWxD). Wheel recesses with square climbing strips approx. 15 x 15 mm and widenings in the lower area * Between the 1st and 2nd axles a pair of permanently installed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D) * Incl. 3-part removable galvanized covers over the wheel recesses (W approx. 670 mm) max. point load 5 t/piece * Recess in the bevel and protruding into the loading area to accommodate the excavator bucket handle (approx. 2,900 x 750 x 210/290 mm) (L x W x H) * 1 pair of lashing rings lying at the front in the loading area (LC 10 000 daN) * 5 pairs of lashing rings that can be folded outwards (LC 5 000 daN) * 3 pairs of lashing rings that can be folded outwards (LC 10 000 daN) * 2 pairs of lashing rings in the excavator boom recess (LC 5 000 daN) * Cutouts in the outer frame of the loading area for attaching tensioning straps (LC 2000 daN) Seat supports * JOST seat supports (mechanical) with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load) Axles * BPW axles and suspension, 2 axles rigid, 1 axle with self-steering * Technical axle load: 12,000 kg each Electro-magnetic reversing lock can be activated via reverse gear and manually * Air suspension with lifting and lowering valve Tires * 235/75 R 17.5 3PMSF Braking system * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines for the tractor unit Steel construction * made of high-strength fine-grain steel * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system * in accordance with EU regulations Gpirtk Lighting * 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15-pin. Connection according to ISO, 24N ISO-1185 24S ISO-3731, 15-pin ISO-12098 Painting * First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer * A high-quality 2-component (2K) top coat in a single color in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) Incl. following additional equipment * 2 inch kingpin * A galvanized steel bulkhead, approx. 400 mm high * A spare wheel holder in front of the bulkhead * Yellow-red air couplings on the galvanized connection strip at the front * 4 brake shoes with holder on the bulkhead * Mount in the rear area of the gooseneck for aluminum docking ramps * Galvanized folding supports under the slope of the loading area * A bracket for a rotating beacon at the rear of the trailer * 3 pairs of recessed lashing rings along the central beam (LC 5,000 daN) * Yellow reflector tape in accordance with EU regulations on the side and rear of the trailer * A bracket for the warning signs including a socket on the left and right of the gooseneck and on the rear panel * A mud flap on the rear of the trailer * Manual and description on USB stick * TPMS tire pressure

Overall weight: 48,000 kg, maximum load weight: 37,100 kg, axe configuration: 3 axles, Condition: new, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Gooseneck * with bevelled corners at the front approx. 45° and with a rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Ramps * A pair of galvanised one-piece steel ramps, approx. 3,000 x 800 mm, with a hardwood flooring approx. 48 mm thick * Ramp with hydraulic lifting mechanism, hydraulically movable * Maximum load per pair: 40,000 kg * In accordance with Regulation 1230/2012/EU, ramps with a length of less than 300 mm in the driving position do not have to be taken into account in the vehicle length Loading area * Telescopic loading area with a bevel at the rear approx. 1,000 mm x 8° * 1 pair of permanently installed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing strips approx. 15 x 15 mm and widening in the lower area * A pair of permanently installed wheel recesses between the 1st and 2nd axle, approx. 1,610 x 970 x 400 mm (L x W x D) * Incl. 3-part removable galvanized covers over the wheel recesses (approx. 670 mm) max. point load 5 t / piece * Recess in the bevel and protruding into the loading area to accommodate the excavator bucket handle (approx. 2,900 x 750 x 210/290 mm (L x W x H) * 1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) * 5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 2 pairs of lashing rings in the excavator arm recess (LC 5,000 daN) * Cut-outs in the outer frame of the loading area for attaching tensioning straps (LC 2,000 daN) Seat supports * JOST (mechanical) with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load) Dpq2Sd Axles * BPW axles and suspension, 2 axles rigid, 1 axle with trailing steering * Technical Axle load: 12,000 kg each * Electro-magnetic reversing lock can be activated via reverse gear and manually Air suspension * with raising and lowering valve Tires * 235/75 R 17.5 3PMSF Braking system * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Steel construction * made of high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system * in accordance with EU regulations * Lighting 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin, connection in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork * First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer * A high-quality 2-component (2K) top coat in a single color in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) Incl. the following additional equipment * 2 inch kingpin * A galvanized steel bulkhead, approx. 400 mm high * A spare wheel holder in front of the bulkhead * Yellow-red air couplings on the galvanized connection strip at the front * 4 brake shoes with holder on the bulkhead * Mount in the rear area of the gooseneck for aluminum docking ramps * Galvanized folding supports under the bevel of the loading area * A bracket for a Rotating beacon at the rear of the trailer * Cover plates to bridge the space between the ramps and the loading area * 3 pairs of recessed las

Overall weight: 50,960 kg, maximum load weight: 39,720 kg, axe configuration: > 3 axles, Condition: new, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Gooseneck * with bevelled corners at the front approx. 45° and with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area Loading area in extendable version * 5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) * Cutouts in the outer frame of the loading area for hanging tensioning straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, checkered sheet metal flooring above the axles Seat supports * JOST (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles * BPW axles, two axles rigid, two axles self-steering, with drum brake * Air suspension with lifting/lowering function * Self-steering axle with electromagnetic reversing lock, can be activated via reverse gear or manually * Tires: 205/65 R 17.5 Braking system * Wabco braking system in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Steel construction * made of high-strength fine-grain steel * Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paintwork * First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) coating Zinc dust primer * A high-quality 2-component (2K) top coat in a single color in RAL 3002 carmine red * Rear part metallized and painted in RAL 9010 (pure white) * Rims in silver Accessories included * 2 inch kingpin * A galvanized steel bulkhead approx. 400 mm high * A spare wheel holder in front of the bulkhead * Yellow-red air couplings on the galvanized connection strip at the front * 4 brake shoes with holder on the bulkhead * Mount in the rear area of the gooseneck for aluminum docking ramps * Galvanized folding supports under the slope of the loading area * A bracket for a rotating beacon at the rear of the trailer * Yellow reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer * A bracket for the warning signs including a socket on the gooseneck and on the rear panel on the left and right * TPMS tire pressure monitoring system in accordance with ECE R 141. The data is transferred to the towing vehicle via the standardized EBS interface according to ISO 11992. For correct display, the towing vehicle must be able to transfer and display this data. Bwkad7X9 * On the gooseneck aluminum side walls and rear wall, pluggable, approx. 2,440 x 400 mm (L x H), the rear galvanized plug-in stanchions are removable. (Length of the body approx. 2,560 mm) * A galvanized toolbox, integrated in the beveled gooseneck * 6 pairs of WADER container pockets in the loading area, for 1 x 20' container, 2 x 20' container or 1 x 40' container * Movable hanging rails for aluminum docking ramps at the rear of the vehicle * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading area * A galvanized bracket across the loading area * Galvanized extensions, extendable by approx. 230 mm on each side * Lift axle on the front axle with control by TEBS E depending on the current axle load and the current loading condition * 5 pairs of recessed lashing rings along the central beam (LC 5,000 daN) * 1 pair

Overall weight: 48,000 kg, maximum load weight: 36,210 kg, axe configuration: 3 axles, Condition: new, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Gooseneck * Gooseneck with bevelled corners at the front approx. 45° and with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area * in extendable version with rear bevel approx. 1,000 mm x 8° * Can be raised and lowered hydraulically after the gooseneck, length approx. 2,800 mm * 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings that can be folded inwards on the central support at the front (LC 10,000 daN) * Cutouts in the outer frame of the loading area for hanging tensioning straps (LC 2000 daN) * C40/4 grating (point load approx. 2.3 t on an area of approx. 20 x 20 cm) * Checkered sheet covering above the axles Two-part steel ramps * A pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with C40/4 grating (point load approx. 2.2 t on an area of approx. 20 x 20 cm) * Ramp with hydraulically foldable and unfoldable ramp parts * Hydraulic lifting mechanism, hydraulically movable * Maximum load per pair: approx. 40,000 kg * In accordance with Regulation 1230/2012/EU, ramps with a length of less than 300 mm in the driving position do not have to be taken into account in the vehicle length of 16,500 mm Axles * BPW axles and suspension * 2 axles rigid, 1 axle with self-steering * Technical axle load: 12,000 kg each * Electromagnetic reversing lock can be activated via reverse gear and manually Air suspension Bhcdd7Os * with lifting and lowering valve * Axle tool Tires * 235/75 R 17.5 3PMSF Seat supports * JOST seat supports (mechanical) with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load) Braking system * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Painting * First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer * A high-quality 2-component (2K) top coat in a single color in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) * No metallic painting possible Steel construction made of * high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system * in accordance with EU regulations Lighting * 24 volts ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15-pin connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included * 2 inch kingpin * A galvanized steel bulkhead, approx. 400 mm high * A spare wheel holder in front of the bulkhead * Yellow-red air couplings on the galvanized connection strip at the front * 4 wheel chocks with holder on the bulkhead * Galvanized folding supports under the slope of the loading area * A bracket for a rotating beacon at the rear of the trailer * Grating in the slope of the gooseneck C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * Grating in the slope of the loading area C40/4 (point load approx. 3.4 t on an area of approx. 20 x 20 cm) * Cover plates to bridge the free space between ramps and loading area * A painted layer of sand on the checker plates on the gooseneck and the loading area as anti-slip protection * Yellow reflective tape on the sides and rear i

Overall weight: 50,960 kg, maximum load weight: 39,590 kg, axe configuration: > 3 axles, Condition: new, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Gooseneck * with hardwood covering approx. 30 mm thick. Gooseneck at the rear in a straight design * 3 pairs of lashing rings (LC 5,000 daN) Loading area * in an extendable design * 5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) * Cutouts in the outer frame of the loading area for hanging tensioning straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, checkered sheet metal flooring above the axles Seat supports * JOST seat supports (mechanical) with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load) Axles * BPW axles, two axles rigid, two axles with trailing steering * air-suspended, with lifting/lowering function * Self-steering axles with electro-magnetic reversing lock, activated via reverse gear or manually * Drum brakes Tires * 205/65 R 17.5 Brake system * in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Steel construction * made of high-strength fine-grain steel * Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Segwfwuwkl Paintwork * First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer * A high-quality 2-component (2K) top coat in a single color in RAL 3002 carmine red * Rear section metallized and in RAL 9010 (pure white) painted * Rims in silver Accessories included * 2 inch kingpins * A spare wheel holder in front of the bulkhead * Yellow-red air couplings on the galvanized connection strip at the front * 4 wheel chocks with holders on the bulkhead * Galvanized folding supports under the slope of the loading area * A bracket for a rotating beacon at the rear of the trailer * Yellow reflective tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer * A bracket for the warning signs on the gooseneck and on the rear panel on the left and right, including a socket * A mud flap at the rear of the trailer * Manual and description on USB stick * European reflector signs (red-yellow) on the rear of the trailer * Speed sticker 80 km/h at the rear and on both sides * Load gauge for determining the axle loads including load diagram * A galvanized steel bulkhead (EN12642-XL), approx. 1,200 mm high * Support stand with 1 pair of WADER container pockets, load capacity approx.: 20,000 kg * 7 pairs of WADER container pockets for: 1x 20' container or 1x 40' container in the loading area, 1x 40' container above the gooseneck or 2x 20' containers * 7 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area * A galvanized bracket across the loading area * Galvanized extensions, extendable by approx. 230 mm per side * Lift axle on the front axle with control by TEBS E depending on the current axle load and the current loading status * Movable suspension rails for aluminum docking ramps at the rear of the vehicle * Bracket for aluminum docking ramps, across the loading area in front of the axles * 1 pair of recessed lashing rings along the central beam at the rear in the bevel (LC 10 000 daN) * 2 LED reversing lights mounted on the rear panel * 2 pairs of Ferry rings under the gooseneck and 2 pairs at the rear * An acoustic warning signal when

Overall weight: 50,960 kg, maximum load weight: 39,780 kg, axe configuration: > 3 axles, first registration: 01/2023, next inspection (TÜV): 01/2025, Year of construction: 2022, Condition: used, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Gooseneck * with bevelled corners at the front approx. 45° and with a rear bevel of approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood covering approx. 30 mm thick Loading area * in extendable version * 5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) * Cutouts in the outer frame of the loading area for hanging tensioning straps (LC 2,000 daN) * Hardwood covering approx. 48 mm thick, checkered sheet covering above the axles Seat supports * JOST seat supports (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Tires * 205/65 R 17.5 twin tires Axles * BPW axles, two axles rigid * two axles self-steering * air-suspended, with drum brake * with lifting/lowering function * The self-steering axles with electromagnetic reversing lock can be activated via reverse gear or manually Braking system * in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Steel construction * made of high-strength fine-grain steel * Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paintwork * First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) coating Zinc dust primer * A high-quality 2-component (2K) top coat in a single color in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) * Rims in silver Electrical system * in accordance with EU regulations Lighting Cxr0980Jus * 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15-pin. * Connection in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included * 2 inch kingpin * A galvanized steel bulkhead approx. 400 mm high * A spare wheel holder in front of the bulkhead * Yellow-red air couplings on the galvanized connection strip at the front * 4 pieces of chocks with holder on the bulkhead * Mount in the rear area of the gooseneck for aluminum docking ramps * Galvanized folding supports under the slope of the loading area * A bracket for a rotating beacon at the rear of the trailer * Yellow reflective tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer * A bracket for the warning signs including a socket on the gooseneck and on the rear panel on the left and right * A mud flap at the rear of the trailer * Manual and description on USB stick * European reflective signs (red-yellow) at the rear of the trailer * Speed sticker 80 km/h at the rear and both sides * An acoustic warning signal when reversing * Load gauge for determining the axle loads including load diagram

Overall weight: 73,000 kg, maximum load weight: 58,760 kg, axe configuration: > 3 axles, Condition: new, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Gooseneck * with bevelled corners at the front approx. 45° and with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area * in extendable version with rear bevel approx. 500 mm x 8° * 8 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) * Cutouts in the outer frame of the loading area for hanging tensioning straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, checkered sheet flooring above the axles Two-part steel ramps * A pair of galvanised two-part steel ramps, approx. 2,750 + 1,400 x 900 mm, with Super Grip rubber covering. Ramp with hydraulically foldable and unfoldable ramp parts * Hydraulic lifting mechanism, hydraulically movable * Maximum load per pair: 40,000 kg Dqojpv Axles * BPW axles and suspension, 1st axle with leading steering, 2nd and 3rd axles rigid, 4th and 5th axles with trailing steering, air suspension, with lifting/lowering function, drum brakes * Trailing steering axles with electro-magnetic reversing lock, can be activated via reverse gear or manually * Technical axle load: 12,000 kg each Tires * 235/75 R 17.5 3PMSF Seatposts * JOST seatposts (mechanical) with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load) Braking system * Wabco Brake system in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Steel construction * made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system * in accordance with EU regulations * Lighting 24 volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15-pin connection in accordance with ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork * First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer * A high-quality 2-component (2K) top coat in a single color in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) Incl. the following additional equipment * 2 inch kingpin * A galvanized steel bulkhead, approx. 400 mm high * A spare wheel holder in front of the bulkhead * Yellow-red air couplings on the galvanized connection strip at the front * 4 brake shoes with holder on the bulkhead * Mount in the rear area of the gooseneck for aluminum docking ramps * A bracket for a rotating beacon at the rear of the trailer * Galvanized Supports under the slope of the loading area * Super Grip 25 rubber covering in the slope of the loading area * Cover plates to bridge the space between the ramps and the loading area * Yellow reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer * Electro-hydraulic unit at the rear, under the loading area * A holder for the warning signs on the left and right of the gooseneck and on the rear panel, including a socket * TPMS tire pressure monitoring system in accordance with ECE R 141 * Load gauge for determining the axle loads, including load diagram * Aluminum side walls and rear wall on the gooseneck, plug-in, approx. 2,440 x 400 mm (L x H), the rear galvanized plug-in stanchions are removable (length of the structure approx. 2,560 mm) * A galvanized tool

Overall weight: 48,000 kg, maximum load weight: 38,885 kg, axe configuration: 3 axles, Condition: new, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Sfggzt8Emz Loading area in extendable design, with rear slope of approx. 1,000 mm x 8° * Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles * JOST saddle supports (mechanical) with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load) * BPW axles and suspension, 2 axles rigid, 1 axle with trailing steering * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Braking system in accordance with EU regulations with EBS-E (2S2M) * Top coat in single color in RAL 3002 carmine red * 2 inch king pin * A galvanized steel front wall approx. 400 mm high * Load gauge for determining the axle loads including load diagram * Aluminum side walls on the gooseneck and Rear wall, pluggable, approx. 2 440 x 400 mm (L x H) * A galvanized toolbox, integrated in the beveled gooseneck * 3 pairs of WADER container pockets in the loading area for a 20' (30') or a 40' container * 6 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading area * Galvanized extensions, extendable by approx. 230 mm per side * Lift axle on the front axle * Movable hanging rails for aluminum docking ramps at the rear of the vehicle * 2 LED reversing lights mounted on the rear panel * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm, with an LED position light * A bracket for a rotating beacon on the warning signs * A rotating beacon loose included * HRM metallization (High Resistance Metallization)

Overall weight: 48,000 kg, maximum load weight: 37,630 kg, axe configuration: 3 axles, Condition: new, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Gooseneck * with bevelled corners at the front approx. 45° and with bevelled corners at the rear approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5 000 daN) * Hardwood flooring approx. 30 mm thick One-piece steel ramps * One pair of galvanised one-piece steel ramps, approx. 3 000 x 800 mm, with hardwood flooring approx. 48 mm thick * Ramp with hydraulic lifting mechanism, hydraulically movable * Maximum load per pair: 40,000 kg * In accordance with Regulation 1230/2012/EU, ramps with a length of less than 300 mm in the driving position do not have to be included in the vehicle length Loading area * 1 pair of permanently installed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing strips approx. 15 x 15 mm and widening in the lower area * Between the 1st and 2nd axle a pair of permanently installed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D) * Incl. 3-part, removable, galvanized covers over the wheel recesses (approx. 670 mm) - max. point load 5 t / piece * Recess in the bevel and protruding into the loading area to accommodate the excavator bucket handle (approx. 2,900 x 750 x 210/290 mm (L x W x H) * 1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) * 5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 2 pairs of lashing rings in the excavator arm recess (LC 5,000 daN) * Cutouts in the outer frame of the loading area for attaching tensioning straps (LC 2,000 daN) Seat supports * JOST seat supports (mechanical) with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load) Axles * BPW axles and suspension, 2 axles rigid, 1 axle with trailing steering * Technical Axle load: 12,000 kg each D7Vbwbs * Electro-magnetic reversing lock can be activated via reverse gear and manually Air suspension * with lifting and lowering valve Tires * 235/75 R 17.5 3PMSF Braking system * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Steel construction * made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system * in accordance with EU regulations Lighting * 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork * First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer * A high-quality 2-component (2K) top coat in a single color in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) Incl. the following additional equipment * 2 inch kingpin * A galvanized steel bulkhead, approx. 400 mm high * A spare wheel holder in front of the bulkhead * Yellow-red air couplings on the galvanized connection strip at the front * Mount in the rear area of the gooseneck for aluminum docking ramps * Galvanized folding supports under the bevel of the loading area * A bracket for a rotating beacon at the rear of the trailer * Cover plates to bridge the space between ramps and loading area * 3 pairs of recessed lashing rings along the central beam (LC 5,000 daN) * Electro-hydraulic unit at the rear, u

Overall weight: 58,000 kg, maximum load weight: 47,300 kg, axe configuration: > 3 axles, Condition: new, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Gooseneck * with bevelled corners at the front approx. 45° and with a rear bevel of approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood covering approx. 30 mm thick Loading area * in extendable version with rear bevel of approx. 1,000 mm x 8° * 5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) * Cutouts in the outer frame of the loading area for hanging tensioning straps (LC 2,000 daN) * Hardwood covering approx. 48 mm thick * Checkered sheet covering above the axles Seat supports * JOST seat supports (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Tires * 235/75 R 17.5 3PMSF Axles * BPW axles, two axles rigid, two axles self-steering, air-suspended * with drum brake with lifting/lowering function * The self-steering axles with electro-magnetic reversing lock can be activated via reverse gear or manually Braking system * WABCO braking system in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Noiyb99Am2 Paintwork * A high-quality 2-component (2K) top coat in a single color in RAL 3002 carmine red Accessories * A spare wheel holder in front of the bulkhead (without electric wheel) * 2 inch kingpin * A galvanized steel bulkhead approx. 400 mm high * On the galvanized connection strip at the front yellow-red air couplings * 4 pieces of brake shoes with holder on the front wall * Mount in the rear area of the gooseneck for aluminum docking ramps * Galvanized folding supports under the slope of the loading area * A bracket for a rotating beacon at the rear of the trailer * Yellow reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer * A bracket for the warning signs on the left and right of the gooseneck and on the rear panel including a socket * Load pressure gauge for determining the axle loads including load diagram Incl. special accessories * Aluminum side walls and rear wall on the gooseneck, pluggable, approx. 2 440 x 400 mm (L x H) * A galvanized toolbox, integrated in the sloped gooseneck * 3 pairs of WADER container pockets in the loading area for a 20' (30') or a 40' container * Movable Hanging rails for aluminum landing ramps at the rear of the vehicle * 6 pairs of stake pockets for stakes approx. 100 x 50 mm in the outer frame of the loading area * Galvanized extensions, extendable by approx. 230 mm per side * Lift axle on the front axle with control by TEBS E * 2 LED reversing lights mounted on the rear panel * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * An acoustic warning signal when reversing * HRM metallization (High Resistance Metallization)

Overall weight: 48,000 kg, maximum load weight: 36,210 kg, axe configuration: 3 axles, first registration: 09/2023, next inspection (TÜV): 10/2025, Condition: used, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Gooseneck * with bevelled corners at the front approx. 45° and with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area * in extendable version with rear bevel approx. 1,000 mm x 8° * Can be raised and lowered hydraulically after the gooseneck, length approx. 2,800 mm * 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings that can be folded inwards on the central support at the front (LC 10,000 daN) * Cutouts in the outer frame of the loading area for hanging tensioning straps (LC 2000 daN) * Grating flooring C40/4 (point load approx. 2.3 t on an area of approx. 20 x 20 cm) * Checkered sheet covering above the axles Two-part steel ramps * A pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with grating covering C40/4 (point load approx. 2.2 t on an area of approx. 20 x 20 cm) * Ramp with hydraulically foldable and unfoldable ramp sections * Hydraulic lifting mechanism, hydraulically movable Br8Puk3Rpuq * Maximum load per pair: approx. 40,000 kg * In accordance with Regulation 1230/2012/EU, ramps with a length of less than 300 mm in the driving position do not have to be taken into account in the vehicle length of 16,500 mm Axles * BPW axles and Suspension * 2 axles rigid, 1 axle with self-steering * Technical axle load: 12,000 kg each * Electro-magnetic reversing lock can be activated via reverse gear and manually Air suspension * with lifting and lowering valve Tires * 235/75 R 17.5 Seat supports * JOST seat supports (mechanical) with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load) Brake system * in accordance with EU regulations with EBS-E (2S2M) * without connecting lines to the tractor unit Paintwork * First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer * A high-quality 2-component (2K) top coat in a single color in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) Steel construction * made of high-strength fine-grain steel * Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system * in accordance with EU regulations Lighting * 24 volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15-pin. * Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included * 2 inch kingpin * A galvanized steel bulkhead, approx. 400 mm high * A spare wheel holder in front of the bulkhead * Yellow-red air couplings on the galvanized connection strip at the front * 4 brake shoes with holder on the bulkhead * Galvanized folding supports under the slope of the loading area * A bracket for a rotating beacon at the rear of the trailer * Grating in the slope of the gooseneck C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * Grating in the slope of the loading area C40/4 (point load approx. 3.4 t on an area of approx. 20 x 20 cm) * Cover plates to bridge the free space between ramps and loading area * A painted layer of sand on the checker plates, above the kingpin and the loading area as anti-slip protection * Yellow reflective tape in accordance with EU regulations on the side and rear of the trailer * Elec

Overall weight: 58,000 kg, maximum load weight: 47,175 kg, axe configuration: > 3 axles, first registration: 03/2023, Condition: used, total width: 2,540 mm, Equipment: ABS, Extract from the equipment. Complete equipment on request. Gooseneck * Gooseneck with bevelled corners at the front approx. 45° and with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area * Loading area in extendable version with rear bevel approx. 1,000 mm x 8° * 5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) * Cutouts in the outer frame of the loading area for hanging tensioning straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, checkered sheet covering above the axles Czcyrwkfd3 Axles * BPW axles, two axles rigid, two axles self-steering, air-suspended, with lifting/lowering function, drum brakes * Self-steering axles with electro-magnetic reversing lock, can be activated via reverse gear or manually Tires * Tires 235/75 R 17.5 Seatposts * JOST seatposts (mechanical) with 2-speed gearbox for approx. 24 t lifting load (approx. 50 t test load) Braking system * Braking system in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Coating/painting * HRM metallization (High Resistance Metallization) * Single color in RAL 3002 carmine red Incl. the following additional equipment * 2 inch kingpin * A galvanized steel bulkhead, approx. 400 mm high * A Spare wheel holder in front of the bulkhead * A holder for the warning signs and extension lights on the gooseneck and on the rear panel on the left and right * Load gauge for determining the axle loads including load diagram * Aluminum side walls and rear wall on the gooseneck, pluggable, approx. 2,440 x 400 mm (L x H) * A galvanized toolbox, integrated in the beveled gooseneck * 3 pairs of WADER container pockets in the loading area for a 20' (30') or a 40' container * Movable hanging rails for aluminum docking ramps at the rear of the vehicle * 6 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading area * Galvanized extensions, extendable by approx. 230 mm per side * Lift axle on the front axle * 2 LED reversing lights mounted on the rear panel * 2 pairs of ferry rings under the gooseneck and 2 couple in the back

Overall weight: 48,000 kg, empty load weight: 10,350 kg, maximum load weight: 37,650 kg, operation weight: 10,350 kg, axe configuration: 3 axles, loading space length: 8,600 mm, loading space width: 2,540 mm, loading space height: 860 mm, first registration: 10/2018, suspension: air-lift, color: orange, tire size: 245/70 R 17,5, Year of construction: 2018, Condition: used, Equipment: ABS, You will receive a current and complete inspection and functional report for every used trailer. Gooseneck: -Gooseneck with bevelled corners at the front 45° and with a rear bevel of approx. 750 mm x 10° -2 pairs of lashing rings (LC 5,000 daN) -Hardwood flooring 30 mm thick Loading area in extendable version: -Loading area in extendable version with rear bevel of approx. 1,000 mm x 8° -5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) -Cutouts in the outer frame of the loading area for hanging tensioning straps (LC 2,000 daN) Dqx9Np -Hardwood flooring approx. 48 mm thick Axles and tires: -SAF axles and Suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 10,000 kg -Electro-magnetic reversing lock can be activated via reverse gear and manually -Air suspension with raising and lowering valve -245/70 R 17.5 Braking system: -Braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: -First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer -A high-quality 2-component (2K) top coat in a single color in RAL 2004 pure orange Accessories included: -2" kingpin -A galvanized steel front wall approx. 400 mm high -ALU side walls and rear wall approx. 2,440 x 400 that can be plugged onto the gooseneck mm -The rear stanchions are removable -A spare wheel with holder -4 wheel chocks with holder on the bulkhead -Stainless steel tool box 1,350x400x400 mm on the gooseneck -10 stanchions á 1,000 mm -Shelving for max. 7 pairs of stanchions approx. 100 x 50 mm, screwed to the inside of the bulkhead -Galvanized shelf for extra-wide planks on the right and left -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current loading condition -A bracket for a rotating beacon at the rear of the trailer -Holder in the rear area of the gooseneck for aluminum loading ramps -Galvanized folding supports under the slope of the loading area -White reflector tape in accordance with EU regulations on the side, on the extension and red at the rear -Yellow-red on the galvanized connection strip at the front Air couplings -On the gooseneck and on the rear panel on the left and right, a holder for the warning signs including a socket -Two warning signs extendable by approx. 400 mm, approx. 423 x 423 mm with a position light -6 pairs of stake pockets approx. 100x50 mm in the outer frame of the loading area -Galvanized extensions, extendable by approx. 230 mm on each side -1 movable intermediate table, approx. 250 mm wide, for the extension tube (extends the specified vehicle length) -Movable hanging rail for aluminum docking ramps at the rear of the vehicle -Central lubrication system BEKAMAX (Pico) with normal grease NLGI-2 and removable protection around the pump -A holder for a rotating beacon on the warning signs -European reflector signs (red-yellow) at the rear of the trailer -Speed sticker 80 km/h at the rear and on both sides -Load pressure gauge for determining the axle loads including load diagram -Two plug-in ECE plates loose -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 1

Overall weight: 50,000 kg, empty load weight: 12,100 kg, maximum load weight: 37,900 kg, axe configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, first registration: 03/2022, suspension: air, color: grey, tire size: 235/75 r 17,5, Condition: used, machine/vehicle number: 764, Equipment: ABS, You will receive a current and complete inspection and functional report for every used trailer. Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood covering 30 mm thick Extendable loading area: -Extendable loading area with rear bevel of approx. 1,000 mm x 8° -5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) -Hardwood covering approx. 48 mm thick, checkered sheet covering above the axles Two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood flooring -Ramp with hydraulically foldable ramp parts, hydraulic lifting mechanism and hydraulically movable -Maximum load per pair: 40,000 kg Seatposts: -JOST seatposts (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Axles and tires: -BPW axles and suspension, all axles hydromechanically forced steered -Technical axle load: 12,000 kg -Air suspension with lifting and lowering valve -Tires 235/75 R 17.5 Braking system: -Braking system in accordance with EU regulations with EBS-E (2S2M) Steel construction: -Steel construction made of high-strength Fine-grained steels -Steel qualities: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Paintwork: -First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer -A high-quality 2-component (2K) top coat in a single color in Nova gray -Rear section metallized and painted in RAL 9010 (pure white) -No metallic paint possible Electrical system: -Electrical system in accordance with EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) -ASPÖCK-UNIBOX on the front connection strip with sockets 2x 7-pin & 1x 15-pin -Connection in accordance with ISO -24N ISO-1185 -24S ISO-3731 -15-pin ISO-12098 Accessories included: -2" kingpins -A galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -A spare wheel with holder in front of the bulkhead -Electro-hydraulic unit -Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles -Holder in the rear area of the gooseneck for aluminum docking ramps -European reflector signs (red-yellow) on the rear of the trailer Dmhcov -White reflector tape in accordance with EU regulations on the side, on the extension and at the rear, red -A holder for the warning signs including a socket on the gooseneck and on the ramps on the left and right -A holder for a rotating beacon on the rear of the trailer -Galvanized folding supports under the slope of the loading area -Control valves for the ramps mounted on the right side of the trailer -A mud flap at the rear of the trailer -Cover plates to bridge the space between the ramps and the loading area -Manual and description -ALU side walls and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm (L x H) -The rear galvanized plug-in stanchions are removable. (Length of the structure approx. 2,560 mm) -4 pairs of WADER container pockets in the loading area for a 20ft, 2x 20ft, 40ft or a 45ft container

Overall weight: 49,500 kg, empty load weight: 10,730 kg, maximum load weight: 38,770 kg, axe configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, first registration: 07/2024, suspension: air, color: grey, tire size: 235/75 R 17,5 3PMSF, Year of construction: 2024, Condition: used, Equipment: ABS, Gooseneck: -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Loading area in extendable version: -Loading surface in extendable version with rear slope of approx. 1,000 mm x 8° -6 pairs of lashing rings can be folded outwards -3 pairs of lashing rings can be folded outwards -1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: -A pair of galvanized, two-part steel ramps, approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable -Maximum load per pair: approx. 40,000 kg Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electro-magnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 3PMSF -TPMS tire pressure monitoring system Paint finish: -First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component zinc dust primer Dqoeif A high-quality 2-component top coat in one color in MB 7350 nova grey Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -One bracket for rotating beacon at the rear of the trailer -Mounting in the rear area of the gooseneck for ALU trailer lights -Galvanized folding supports under the bevel of the cargo bed -Cover plates to bridge the space between the ramps and the cargo bed -White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear -Electric hydraulic unit at the rear, under the cargo bed -On the gooseneck and on the ramps on the left and right a holder for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -ALU drop sides and rear wall can be plugged onto the gooseneck, approx. 2,440 x 400 mm -The rear, galvanized stanchions are removable Length of the body approx. 2,560 mm -Four warning signs, extendable by approx. 400 mm, approx. 423 x 423 mm with one position light -3 pairs of WADER container pockets in the loading area for a 20ft, 30ft or 40ft container -6 pairs of stake pockets approx. 100x50 mm in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -A layer of sand painted onto the chequer plates, above the kingpin and the cargo bed to prevent slipping -On the warning plates a holder for rotating beacon -European reflector plates (red/yellow) at the rear of the trailer -Speed stickers 80 km/h at the rear and on both sides -Load manometer to determine the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-peened, then the defined visible surfaces coated in Metallization with ZINACOR 850 (zinc 85% - aluminium 15%) hot-finished

Overall weight: 60,800 kg, empty load weight: 11,880 kg, maximum load weight: 48,920 kg, axe configuration: > 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, first registration: 09/2024, suspension: air, color: grey, tire size: 235/75 R 17.5, Year of construction: 2024, Condition: used, Equipment: ABS, You receive a current & complete inspection and function report with every used trailer. Gooseneck: -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° -Hardwood decking 30 mm thick Loading surface in extendable version: -Load surface in extendable design with rear bevel of approx. 1,000 mm x 8° Cut-outs in the outer frame of the cargo bed for attaching tensioning straps (LC 2,000 daN) -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Removable two-part ramps: -A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable -Maximum load per pair: 40,000 kg Seat posts: -JOST fifth wheels (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Axles and tires: -BPW axles, two axles rigid two axles self-steering, air-suspended, with drum brake, with lifting/lowering function The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -axle tool -235/75 R 17.5 tires -TPMS tire pressure monitoring system Accessories included: Dqmab9 -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -One spare wheel with holder in front of the bulkhead -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -Galvanized folding supports under the bevel of the cargo bed -Cover plates to bridge the gap between the ramps and the cargo bed -White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear -Electric hydraulic unit at the rear under the cargo bed -On the gooseneck and on the ramps on the left and right a holder for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -One mud flap at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -4 pairs of WADER container pockets in the loading area for one 20ft, 2x 20ft or one 40ft container -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -a layer of sand painted onto the chequer plates, above the kingpin and the cargo bed to prevent slipping -BEKAMAX (Pico) central lubrication system, with NLGI-2 standard grease and with removable protection around the pump. -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with one position light -Speed sticker 80 km/h at the rear and on both sides -Load manometer to determine the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Overall weight: 60,800 kg, maximum load weight: 49,000 kg, axe configuration: > 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, color: grey, tire size: 235/75 r 17.5, Condition: new, Equipment: ABS, Gooseneck: -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area in extendable version: -Loading surface in extendable version with rear bevel of approx. 1,000 mm x 8° -5 pairs of lashing rings can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps. (LC 2,000 daN) -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Removable two-part ramps: -A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking 9Wv00U3 -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable -Maximum load per pair: 40,000 kg Seat posts: -JOST fifth wheels (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles, two axles rigid two axles self-steering, air-suspended, with drum brake, with lifting/lowering function The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -axle tool -235/75 R 17.5 tires Brake system: -brake system in accordance with EU regulations with EBS-E (4S3M) Steel construction: -steel construction made of high-strength fine-grained steels -Steel grades: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Coating: -First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in nova grey Electrical system: -Electrical system in accordance with EU regulations, 24 volt ASPÖCK-NORDIK lighting (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Accessories included: -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -One spare wheel with holder in front of the bulkhead -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon -Cover plates to bridge the gap between ramps and cargo bed -White reflector tape in accordance with EU regulations on the sides, on the extension and red at the rear -Electric hydraulic unit -On the gooseneck and on the ramps on the left and right a holder for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -One mud flap at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -4 pairs of WADER container pockets in the loading area for one 20ft, 2x 20ft or one 40ft container -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -Lift axle on the front axle with controls -Square climbing rails 20 x 20 mm -BEKAMAX central lubrication system -Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm

Overall weight: 50,000 kg, maximum load weight: 38,100 kg, axe configuration: > 3 axles, loading space length: 13,100 mm, loading space width: 2,480 mm, loading space height: 760 mm, first registration: 09/2024, suspension: air, color: grey, tire size: 205/65 R17.5, Year of construction: 2024, Condition: used, Equipment: ABS, Gooseneck: -gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Loading area: -5 pairs of lashing rings can be folded outwards -3 pairs of lashing rings can be folded outwards -1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Seat posts: -JOST semi-trailer supports with 2-speed gearbox for 24 t lifting capacity Axles and tires: -BPW axles, two rigid axles two self-steering axles, air-suspended, with drum brake, with lifting/lowering function The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -axle tool -Tires 205/65 R17.5 3PMSF Brake system: -WABCO brake system in accordance with EU regulations with EBS-E Steel construction: -steel construction made of high-strength fine-grained steels -Steel grades: -S355J2+N/S355MC & S690QL/S700MC Coating: -First-class and durable corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component zinc dust primer -Single color in MB 7350 nova grey Accessories included: - 1 spare wheel 205/65 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 -2" kingpin -One galvanized steel bulkhead -Yellow-red air couplings on the galvanized front connecting strip -4 brake shoes -Receiver in the rear area of the gooseneck for ALU docking ramps -3 heights of aluminum boards -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon at the rear of the trailer -Height-adjustable tarpaulin superstructure -Galvanized bulkhead with a tensioning mechanism for the sliding curtains -Height-adjustable by approx. 400 mm -"EDSCHA" brand roof can be slid forwards on ALU roof rail profiles bolted to the front and rear wall -3 pairs of sliding stanchions in the loading area -The body can be hydraulically widened at the rear to the left and right by approx. 750 mm -Sliding roof with pivoting portal support -Sliding tarpaulin with 700 mm reserve in length, with tensioning straps at approx. 600 mm intervals -Height top edge of body approx. 3,960 mm -Driving with the sliding tarpaulin open is not permitted and will damage the tarpaulin -Suspension strip for ALU trailer lights at the rear of the vehicle -White reflector tape in accordance with EU regulations on the side of the trailer and red at the rear -One bracket for the warning signs including socket on the gooseneck and on the left and right rear plate -One mud flap at the rear of the trailer -Manual and description on USB stick -European reflector plates (red/yellow) at the rear of the trailer -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load condition -Rear body closed with ALU hinged doors -A layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping Bsjotfdhy38 -BEKAMAX central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning signs approx. 423 x 423 mm that can be extended by approx. 400 mm with a position light -One bracket for rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -Load manometer for determining the axle loads including load diagra

Overall weight: 48,000 kg, empty load weight: 9,540 kg, maximum load weight: 38,460 kg, axe configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, first registration: 08/2023, suspension: air, color: grey, tire size: 235/75 R 17,5, Year of construction: 2023, Condition: used, Equipment: ABS, You receive a current & complete inspection and function report with every used trailer. Gooseneck: -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° Bscghplns78 -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area in extendable version: -Loading surface in extendable version with rear slope of approx. 1,000 mm x 8° -6 pairs of lashing rings can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Axles and tires: -PW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 3PMSF Brake system: -brake system in accordance with EU regulations with EBS-E (2S2M) Seat posts: -JOST seat posts (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Steel construction: -steel construction made of high-strength fine-grained steels -Steel qualities: -S355J2+N/S355MC (yield strength 355MPa -S690QL/S700MC (yield strength 690 MPa) Electrical system: -Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK (ASS3) -ASPÖCK-UNIBOX on the terminal strip at the front with 24N, 24S & 15-pin sockets Accessories included: -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -One spare wheel with holder in front of the bulkhead -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -One bracket for rotating beacon at the rear of the trailer -Mounting in the rear area of the gooseneck for ALU trailer lights -Galvanized folding supports under the bevel of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -White reflector tape in accordance with EU regulations on the sides, on the extension and red at the rear -On the gooseneck and on the rear panel on the left and right, a holder for the warning signs including socket -One mud flap at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall (approx. 2,440 x 400 mm) can be plugged onto the gooseneck. The rear stanchions are removable -Four warning signs (approx. 423 x 423 mm) that can be extended by approx. 400 mm with a position light -3 pairs of WADER container pockets in the loading area for a 20ft, 30ft or 40ft container -6 pairs of stake pockets (100x50 mm) in the outer frame of the cargo bed -Sliding suspension rails for ALU mooring ramps at the rear of the vehicle -A layer of sand painted onto the chequer plates, above the kingpin and the cargo bed to prevent slipping -On the warning plates a holder for rotating beacon -European reflector plates (red/yellow) at the rear of the trailer -Speed stickers 80 km/h at the rear and on both sides -Load manometer to determine the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Overall weight: 50,100 kg, empty load weight: 12,250 kg, maximum load weight: 37,800 kg, axe configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, first registration: 12/2023, suspension: air-lift, color: grey, tire size: 235/75 R 17,5, Year of construction: 2023, Condition: used, Equipment: ABS, You receive a current & complete inspection and function report with every used trailer. Gooseneck: -gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Loading area in extendable version: -Loading surface in extendable version with rear slope of approx. 1,000 mm x 8° -5 pairs of lashing rings can be folded outwards -3 pairs of lashing rings can be folded outwards -1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Seat posts: -JOST fifth-wheel supports (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles and suspension, all axles hydromechanically forced steered -Air suspension with lifting and lowering valve -235/75 R 17.5 tires Accessories included: -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -One spare wheel with holder in front of the bulkhead -Electric hydraulic unit -Steering can be operated from the front and rear by remote control cable via pushbuttons, with tracking control of the axles -Mounting in the rear area of the gooseneck for ALU docking lights -European reflector plates (red/yellow) at the rear of the trailer -White reflector tape in accordance with EU regulations on the side, on the extension and red at the rear -On the gooseneck and on the ramps on the left and right a holder for the warning signs including a socket -One bracket for a rotating beacon at the rear of the trailer -Galvanized folding supports under the sloping loading area -Control valves for the ramps fitted on the right-hand side of the trailer -Cover plates to bridge the gap between the ramps and the cargo bed -One mud flap at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -4 pairs of WADER container pockets in the loading area for one 20ft, 2x 20ft, 40ft or one 45ft container -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -One INOX toolbox 1,500 x 390 x 810 under the cargo bed on the right in the direction of travel -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump Boeenns7Dng -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -One bracket for rotating beacon on the warning panels -Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control -a layer of sand painted onto the checker plates, above the kingpin and the loading area to prevent slipping -Speed stickers 80 km/h at the rear and on both sides -Load manometer to determine the axle loads including load diagram HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - aluminium 15%)

Overall weight: 49,500 kg, maximum load weight: 38,800 kg, axe configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, color: grey, tire size: 235/75 R 17,5 3PMSF, Condition: new, Equipment: ABS, Gooseneck: -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area in extendable version: -Loading surface in extendable version with rear slope of approx. 1,000 mm x 8° -6 pairs of lashing rings can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) Up92Nu3Ecl -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Axles and tires: -PW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electro-magnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 3PMSF Brake system: -WABCO brake system in accordance with EU regulations with EBS-E (2S2M) Seat posts: -JOST seat posts (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -One bracket for rotating beacon at the rear of the trailer -Mounting in the rear area of the gooseneck for ALU trailer lights -Galvanized folding supports under the bevel of the cargo bed -Cover plates to bridge the space between the ramps and the cargo bed -White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear -Electric hydraulic unit at the rear, under the cargo bed -On the gooseneck and on the ramps on the left and right a holder for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -One mud flap at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall approx. 2,440 x 400 mm on the gooseneck -The rear, galvanized stanchions are removable (length of the body approx. 2,560 mm) -Four warning signs approx. 423 x 423 mm with one position light, extendable by approx. 400 mm -3 pairs of WADER container pockets in the loading area for a 20ft, 30ft or 40ft container -6 pairs of stanchion pockets 100x50 mm in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -A layer of sand painted onto the chequer plates, above the kingpin and the cargo bed to prevent slipping -On the warning plates a holder for rotating beacon -European reflector plates (red/yellow) at the rear of the trailer -Speed stickers 80 km/h at the rear and on both sides -Load manometer to determine the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Overall weight: 49,500 kg, empty load weight: 10,350 kg, maximum load weight: 39,150 kg, axe configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air/air, color: grey, tire size: 235/75 R 17,5, Condition: new, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area: -telescopic loading area with rear slope approx. 1,000 mm x 8° -1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm -Wheel recesses with square climbing strips 15 x 15 mm and widenings in the lower area -A pair of fixed wheel recesses between the 1st and 2nd axles, approx. 1,610 x 970 x 400 mm -3-piece removable galvanized covers over the wheel recesses (W 670 mm) - max. point load 5 to / pc. -Recess in the chamfer and protruding into the loading area to accommodate the excavator dipper stick approx. 2,900 x 750 x 210/290 mm -1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) -5 pairs of lashing rings foldable outwards (LC 5,000 daN) -2 pairs of lashing rings can be folded outwards (LC 10,000 daN) -2 pairs of lashing rings in the excavator trough (LC 5,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) One-piece ALU ramps: -One pair of one-piece ALU ramps approx. 2,500 x 600 mm -Ramp with spring lifting mechanism and manually adjustable -Maximum load per pair: 24,000 kg Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 tires -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking lights -Galvanized extensions, extendable by approx. 230 mm per side -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon at the rear of the trailer -White reflector tape in accordance with EU regulations on the sides, on the pull-out and red at the rear -One bracket for the warning signs including socket on the left and right of the gooseneck and on the rear panel -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container Ic028Uugw -3 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -One removable galvanized intermediate table with 1 pair of WADER container pockets -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -a layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -A bracket for a rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)