Working platform semitrailer

MÜLLER-MITTELTAL 3-Achs Satteltieflader überfahrbar m. Radmulden

Condition: new, maximum load weight: 37,500 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Year of construction: 2024, * TS 3 RM 30.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11-ton BPW axles * Air suspension with lifting and lowering system and RtR valve * Last axle as self-steering axle with electro-pneumatic steering lock * Side impact protection * Landing gear at the front and swivel supports at the rear of the chassis * 15-pin power connector * LED taillights * Mechanical Adjustable warning sign packages at the front and rear * Rotating beacon (removable) at the rear left * Straight sheet steel fenders * Spare wheel holder in front of the bulkhead cross member (without spare wheel) * Trailer platform with 45° beveled front corners and a toolbox at the front made of galvanized, powder-coated sheet steel (W = 2,480 x H = 500 x L = 665 mm) with a hinged lid * 400 mm aluminum side walls (RAL 9010) on the sides of the trailer platform, foldable and removable * Rear wall -150 mm- high * Rear slope on the trailer platform to the low bed, approx. 700 mm long, each with one recessed lashing ring Bdodpfx Ajl Tiiysgbji * Trailer platform with 50 mm clamped wooden planks and low-loading platform with 60 mm clamped wooden planks * Teardrop plate above the axles * 9 mechanical folding extensions to 3 m Total width, but not including the rear slope (extension planks present with closed storage compartment perpendicular to the direction of travel under the loading area) * 2 lashing bars embedded in the outer frame of the semi-trailer platform on each side, 3 lashing rings on each side in the low-loader platform, and an additional 1 lashing ring in the center of the rear end beam, 2 x 5 ton lashing rings screwed to the bottom of the outer frame of the wheel wells on each side, * 2 x 6.4 ton lashing rings on each side. UVV lashing rings in the excavator boom rest * Excavator boom rest from the end of the last rigid axle over the steering axle to the end support, continuous with internal reinforcement profile approx. L = 2,450 x W = 770 mm x D = 270 mm * Two wheel recesses on each side, 390 mm deep and 640 mm wide, with retractable covers for transporting wheel loaders with a wheelbase of 3,120 - 3,620 mm, front recess at the bottom, slanted upwards by 1,100 mm to a length of 2,050 mm, rear recess at the bottom, slanted upwards by 580 mm to a length of 1,550 mm * Hydraulic. Folding ramp with extendable tip, approx. 4,650 x 720 mm, including load-holding valves and hydraulic lateral ramp adjustment. * The outer board on the ramp is made of 50 mm hardwood. * Loading area above the turntable: approx. 3,950 x 2,480 mm. * Loading height (unloaded): approx. 1,470 mm. * Lower loading area: approx. 8,500 x 2,520 mm. * Loading height (unloaded): approx. 910 mm (including 860 mm approach slope). * Chassis, folding supports at the rear, loading ramps, mechanical. Hot-dip galvanized folding extensions * -- Axles, springs, and air chambers painted in a single black tone -- * Suitable for 2- and 3-axle tractors * Fifth wheel height: approx. 1,220 mm * Tires 235/75R17.5 * Gross vehicle weight of 48,000 kg technically possible * Vehicle is hot-dip galvanized * Side walls painted in RAL 9010 pure white * Side walls painted in a RAL color available for an additional charge * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf