Used Fliegl Vts 400 Rr for sale (7,296)

Condition: new, machine/vehicle number: ee3256d63dd23b3ad1bdf9ab0, empty load weight: 10,280 kg, maximum load weight: 13,720 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 storage box on offset recessed in the floor with cover, W=720 mm/ L=520 mm / D= 170 mm 1st pair of wheel recesses recessed in the low bed in the tramline area after the offset, sloping towards the entrance, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area 400 mm higher than wheel recess.2nd pair of wheel recesses between the axles in the drop center in the tramline area, slanted towards the entrance, length at the bottom approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Wheel well cover can be pulled out from the main frame, with wooden inserts. Distance from main frame beam to beam outside approx. 1280 mm (wheel well area) Widenings extendable to 3,000 mm, foldable on the wheel recess extensions (widening not in the rear slope and not in the wheel recesses below) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed or under the cargo bed if technically possible Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 8 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 2 x at the front on the offset 6 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye with 8° inclined drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension with lift & lower valve can be operated separately at the front and rear Wheels and tires Ncjdpji Ri I Nsfx Aazjr 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Trailer Infocenter, for displaying vehicle data such as axle load (no calibrated scales) and odometer Axle load detection via EBS-Canbus signal, for display in the driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Vehicle - driving stability system Duomatic connection at the front, with connecting cable to the truck, EBS, electronic braking system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights in LED with resistor, amber LED lighting on the side, license plate lighting in LED, (Note! with certain towing vehicles, misdiagnoses may occur even though the function is given) 2 white front position lights in LED 2 white/red rear lane departure ligh

Condition: new, maximum load weight: 30,010 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,000 mm, loading space width: 2,520 mm, loading space height: 900 mm, total width: 2,550 mm, Brand-new Fliegl 4-axle low-bed trailer with wheel recesses and split ramps, type VTS 400 RM Hire-purchase offer: 48-month term, down payment only the VAT, final residual value 40% Monthly rate: EUR 899.00 Vehicle / Body: Low-bed trailer First registration: New vehicle Gross weight: 24,000kg/40,000kg Unladen weight: 9,990kg Payload: 14,010kg / 30,010kg Overall length: 12,000mm Loading length: total approx. 10,000mm, gooseneck approx. 2,850mm, load bed including rear taper approx. 7,150mm Width: 2,550mm Loading height: 900mm Further information Chassis: Low-bed trailer Steel welded construction Turntable with heavy-duty ball race Foldable rear support Wheel chocks with holders Aluminum side underrun protection Full-width rear spray flap Half-shell mudguards 1st and 2nd axle with anti-spray mud flaps behind each axle, anti-spray mud flap behind the 4th axle Excavator arm trough above rear axles, from the rear axle to the rear approx. 1,800mm long, approx. 650mm wide and 150mm deep 2 pairs of lashing holes, each 5t, in the excavator arm trough, on the longitudinal frame approx. 300mm from the front and approx. 200mm before the rear taper Spare wheel bracket for 1 spare wheel, upright on the gooseneck, front center, spare wheel brand same as main equipment, steel rim Nsdpfxotrizko Aazecr Toolbox let into the floor on the gooseneck with lid, W=720mm / L=520mm / D=170mm 1st pair of wheel recesses after the gooseneck, let into the deep deck in the driving lane, chamfered for access, length at the bottom approx. 1,600mm, approx. 400mm deep. Note! Frame in the main beam area 400mm higher than the wheel recess. 2nd pair of wheel recesses between the axles, let into the deep deck in the driving lane, chamfered for access, length at the bottom approx. 600mm, approx. 300mm deep. Note! Frame in the main beam area 300mm higher than the wheel recess. Extensions retractable to 3,000mm (no extension at the rear taper and not in the wheel recesses below) (track width of machines or vehicles to be transported must not exceed the outer frame width of 2,550mm) Storage compartment for timber planks underneath the low-bed deck 70mm timber planks for extension to 3,000mm Lashing points – low-bed trailer 1 pair of RIN lashing rings inlaid at the front on the gooseneck, each 5t 4 pairs of lashing holes in the outer frame, each 5t (for securing strap attachments) 8 pairs of lashing mushrooms flush-mounted top and side in the outer frame, each 10t 2 at the front on the gooseneck 6 in the deep deck First lashing ring 250mm from the front, last a maximum of 250mm from the rear, spacing between lashing rings not more than 1,100mm 5 pairs of stake pockets inlaid in the outer frame, inner dimensions 70 x 40mm (convertible to 5t ring lashing eyes, not included) 1 pair of foldable lashing rings additionally inlaid in the floor, each 10t 1 inside next to main frame at start of low-bed section 2 pairs of additional foldable lashing rings, each 10t 1 on the gooseneck (protrudes) 1 behind the last axle inlaid in the floor Towing device for turntable trailer Drawbar with certified 50mm towing eye, towing eye inclined by 8° D-value at least 160kN Axles and Suspension BPW drum braked axles "Axles/chassis laser aligned" – reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical front axle load equalization (rocker equalizer) Wheels and Tires 235 / 75 R 17.5" Manufacturer’s choice, with M + S marking Steel rims in twin arrangement,

Condition: refurbished (used), functionality: fully functional, machine/vehicle number: WFDFLT44001000966, empty load weight: 9,400 kg, maximum load weight: 30,600 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 10/2010, total length: 12,120 mm, total width: 27,500 mm, total height: 900 mm, suspension: steel, tire size: 235/75 R17,5", color: red, Year of construction: 2010, The images shown are archive photos! Permissible / technical gross weight: 24,000 / 40,000 kg Permissible / technical payload approx.: 14,600 / 30,600 kg Permissible / technical axle load: 24,000 / 40,000 kg Unladen weight (basic version) approx.: 9,400 kg +/- manufacturing tolerance Overall length approx.: 12,120 mm Overall width max.: 2,750 mm Neck length approx.: 2,850 mm Low bed platform length in wheel track area incl. rear bevel approx.: 7,145 mm Rear bevel length approx.: 850 mm Frame width approx.: 2,750 mm Loaded bed height in low bed approx.: 900 mm Drawbar height approx.: 950 mm Drawbar length approx.: 1,700 mm Chassis: Low-bed trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear support 2 wheel chocks with holders Aluminum side underrun protection 1 plastic toolbox, Extendable width up to 3,250 mm (not at rear bevel) (track width of machine/vehicles to be transported must not exceed outer frame width of 2,750 mm) Storage compartment for wooden boards in the center of the loading area 70 mm wooden boards for extension to 3,000 mm 2 pairs of stake pockets in the low bed recessed into the longitudinal beams Lashing points low-bed: 2 pairs of lashing eyes on neck, 5 tons each 1 pair of lashing eyes in rear bevel 4 lashing eyes recessed in the middle of the floor 2 pairs of keyhole profiles in wheel track area for insertion of longitudinal guide rails and as additional lashing option 6 pairs of lashing pins recessed in outer low-bed frame, 10 tons each 5 pairs of stake pockets recessed in the outer frame of the low bed 4 additional pairs of 10 ton lashing eyes: - 1x on neck - 3x recessed in low bed floor Trailer towing device, turntable design Drawbar with certified 50 mm towing eye Axles & Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber mounts and mechanical axle load equalization front and rear (rocker balancing) Wheels and Tires 235/75 R 17.5" Steel twin wheels, factory silver finish Ncodpfx Aeyxq A Heazsr Brake System 2-line compressed air brake system Spring-loaded parking brake 2 foolproof couplings at front, with interconnecting lines to tractor ABS and ALB, with ABS socket at front and connection cable Note: The trailer may only be towed by vehicles ensuring proper ABS functionality! Floor Neck area with steel / checker plate covering Followed by 70 mm softwood floor; in wheel arch area steel / checker plate Rear bevel with 70 mm softwood floor Loading ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable, with wooden covering Hydraulically operated via tractor auxiliary drive Operating Notes At 10,000 kg axle load, an exemption permit is required, only indivisible loads permitted! Note! Oversize length and width require a permanent special permit. When applying for an exemption for regulated heavy haulage, an axle load indicator is required for air-suspended vehicles! This applies to any deviation from § 34 StVZO (axle and permissible total weight overrun), which requires an exemption under § 70 StVZO. The specified gross weight is technically possible; depending on the load, the total weight permitted by axle, support, and kingpin loads may not be achieved. (Poor driving or tracking behavior may occur due to improper load distribution) The images shown are archive photos!

Condition: new, maximum load weight: 31,920 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,410 mm, loading space width: 2,500 mm, loading space height: 900 mm, total width: 2,550 mm, New Fliegl 4-Axle Lowbed Trailer with Ramps, Model VTS 400 Gross weight: 24,000 kg / 40,000 kg Unladen weight: 8,080 kg Payload: 15,920 kg / 31,920 kg Total length: 11,940 mm Loading length: approx. 10,410 mm total, gooseneck approx. 2,490 mm, loading platform incl. rear chamfer approx. 7,920 mm Width: 2,550 mm Loading height: 900 mm Additional information: Plus delivery/preparation ex stock 26639 Wiesmoor €1,280.00 net Chassis - Lowbed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear supports 2 wheel chocks with holders Side underrun protection - aluminum Full-width rear mudflap Half-shell fenders on 1st and 2nd axles with anti-spray flaps behind each axle Anti-spray flaps in front of and behind 3rd and 4th axles Excavator arm recess above the rear axles extending to the rear, approx. 1,800 mm long, approx. 650 mm wide, approx. 150 mm deep 2 pairs of lashing holes (5 t rating each) in the excavator recess, on the longitudinal frame approx. 300 mm from the front and approx. 200 mm before the rear chamfer 1 plastic toolbox (W=600 mm, H=425 mm, D=460 mm), lockable Storage box flush-mounted in floor on the gooseneck, with lid (W=720 mm, L=520 mm, D=170 mm) Extendable widening beams to 3,000 mm (not at rear chamfer) (Note: Maximum track width of construction machines or vehicles must not exceed outer frame width of 2,550 mm) Stowage compartment for wooden planks under the lowbed deck Wooden planks 70 mm wide for extension to 3,000 mm Lashing points - Lowbed 1 pair of recessed lashing cutouts in front longitudinal beam on gooseneck, each rated 10 t 4 pairs of lashing holes in outer frame, each rated 5 t (for attaching tie-down straps) 9 pairs of lashing pins installed flush on top and side of outer frame, each rated 10 t 2 x front on gooseneck 7 x in the lowbed First lashing point 250 mm from front, last max. 250 mm from rear, distance between points no greater than 1,100 mm 3 additional pairs of folding lashing rings, each rated 10 t: 1 x on gooseneck (protruding) 1 x at the start of the lowbed, inset into the longitudinal beams 1 x recessed in floor behind the last axle Towing Arrangement – Turntable Trailer Drawbar with certified 50 mm towing eye Drawbar height adjustable via spring Axles & Suspension Drum brake axles, manufacturer’s choice "Axle/chassis laser alignment" for minimizing tire wear and fuel consumption Air suspension with raise/lower valve and auto-reset function Wheels & Tires 235/75 R 17.5", manufacturer’s choice Steel rims with twin arrangement, factory silver Ncedpfx Aajxrx Nlozsr Brake System 2-line compressed air brake system Spring-applied parking brake Axle load detection via EBS CAN bus signal for display in the truck cab (truck must be pre-equipped; not a calibrated scale) Vehicle – Driving Stability System 2 foolproof coupling heads at front with connecting lines to tractor unit 12-24 Volt EBS, electronic braking system with EBS plug at the front and connection cable (Knorr brand) Note: The towed trailer may only be towed by tractors that guarantee the effectiveness of the ABS! Electrical System 12-24 Volt, multi-chamber LED lights, side yellow LED lighting, LED license plate lighting (Note: Certain tractor units may indicate malfunctions even if all functions are working) 2 white LED position lights at front 2 white/red LED lane marker lights at rear 2 x 7-pin foolproof connectors at front with connection cable 1 LED beacon with holder (switchable via parking lights; lamp removable)

Condition: new, maximum load weight: 31,920 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,410 mm, loading space width: 2,500 mm, loading space height: 900 mm, total width: 2,550 mm, New vehicle Fliegl 4 axle low loader trailer with ramps, type VTS 400 Total weight: 24,000kg/40,000kg Empty weight: 8,080kg Payload: 15,920kg/31,920kg Total length: 11,940mm Loading length: total approx. 10,410mm, offset approx. 2,490mm, loading bed including rear bevel approx. 7,920mm Nodpfx Ajvv D Ixeazjcr Width: 2,550mm Loading height: 900mm Further information plus pre-freight / provision from storage location 26639 Wiesmoor 1,280.00 ¤/ net Rent-purchase offer: term 48 months, down payment only VAT, residual value 40% monthly rate EUR 759.00 Chassis Low-loader trailer Steel welded construction Turntable with strong ball bearing ring Foldable rear support 2 wheel chocks with holder Aluminum side impact protection Rear splash flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray splash flaps behind each axle, Anti-spray splash flaps in front of and behind 3rd and 4th axle Excavator arm recess over the rear axles starting at the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes, each 5 tons. in the excavator arm recess on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear bevel 1 plastic tool box, w=600 / h=425 / d=460 mm, lockable Storage box embedded in the floor on a crank with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm (not in the rear bevel) (The track width of the construction machines or vehicles to be transported must not exceed the outer frame width 2,550 mm) Storage compartment for wooden planks below the low-loading area Wooden planks 70 mm for widening to 3,000 mm Lashing eyes for low-loader 1 pair of lashing cutouts embedded in the longitudinal beam at the front on a crank, 10 tons each. 4 pairs of lashing holes in the outer frame, each with 5 tons (tension belt attachment) 9 pairs of lashing mushrooms, each 10 tons, embedded in the outer frame at the top and side 2 x at the front on the bend 7 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the back, distance between the lashing eyes not greater than 1100 mm 3 additional pairs of folding lashing eyes, each 10 tons 1 x on the bend (sticks out) 1 x at the beginning of the low bed, embedded inside on the longitudinal beams 1 x embedded in the floor behind the last axle Towbar with tested 50 mm towing eye Towbar height adjustment via spring Axles + suspension Drum brake axles, as selected by the manufacturer "Laser-measured axles/chassis" Reduction in tire wear and fuel consumption Air suspension with raising & lowering valve + Auto-reset function Wheels and tires 235 / 75 R 17.5" at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Axle load detection via EBS-Canbus signal, for display on display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle - driving stability system 2 interchangeable coupling heads at the front, with connecting cables to the motor vehicle, 12-24 volt EBS, electronic braking system with EBS plug at the front, with connecting cable Knorr brand Caution: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrics 12-24 volts, multi-chamber LED lights, yellow LED lighting on the side, license plate lighting in LED, (Note! Incorrect diagnoses can occur with certain towing vehicles, although the function is p

Condition: new, maximum load weight: 30,310 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, NEW VEHICLE Fliegl 4-axle low loader with 2 pairs of wheel recesses and ramps Total weight 40,000 kg Payload 30,310 kg Empty weight 9,690 kg Total length 12,000 mm Loading length 10,000 mm Loading bed 7,150 mm including 850 mm approach slope Loading height 900 mm 1st pair of wheel recesses after offset in the loading bed, bottom length approx. 1,600 mm, 400 mm deep 2nd pair of wheel recesses between the axles in the loading bed, bottom length 600 mm, 300 mm deep Extensions to 3,000 mm, warning signs, rotating beacon, large lashing package 5 pairs of stake pockets in the outer frame Excavator arm recess 1,800 mm long, 150 mm deep Drawbar 50 mm Air suspension with lifting and lowering valve, can be operated separately BPW drum brakes Tires 235 / 75 R 17.5" Axle load detection via EBS CAN bus signal, Trailer Info Center Ramps 2,800 mm x 750 mm with hydraulic actuation Hydraulic side shift Rent-purchase offer: term 48 months, residual value 40%, down payment only VAT on the rental rates, monthly rate EUR 970.00 net Vehicle will be available from September 11th, 2023 from the Neumünster trade fair. Visit us at Nordbau - Stand West 121 right next to the main entrance. Njdpfx Aasnzlg Djzscr Other 3, 4 and 5 axle low loaders new and used available immediately

Condition: new, maximum load weight: 31,100 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,410 mm, loading space width: 2,500 mm, loading space height: 900 mm, total width: 2,520 mm, Total weight: 24,000kg/40,000kg Empty weight: 8,900kg Payload: 15,100kg/31,100kg Total length: 11,940mm Loading length: 10,410mm total, 2,490mm offset, 7,920mm loading bed including rear bevel Width: 2,520mm Loading height: 900mm Further information plus pre-freight / provision from storage location 26639 Wiesmoor 1,280.00 €/net Steel welded construction Turntable with strong ball bearing ring Foldable rear support Wheel chocks with holder Aluminum side impact protection Rear splash guards across the entire width (not in conjunction with forklift bracket) Half-shell mudguards 1st + 2nd axle with anti-spray splash guards behind each axle, Anti-spray flaps in front of and behind the 3rd and 4th axle Excavator arm recess above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons. in the excavator arm recess on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear bevel 1 plastic tool box, w=600 / h=425 / d=460 mm, lockable 1 storage box embedded in the floor on a crank with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm (not in the rear bevel) Nedpfx Aerducpsazecr (The track width of the construction machines or vehicles to be transported must not exceed the outer frame width 2,550 mm) Storage compartment for wooden planks below the low-loading area Wooden planks 70 mm for widening to 3,000 mm Lashing eyes for low-loader 1 pair of lashing cutouts in the longitudinal beam at the front on a crank, 10 tons each. 4 pairs of lashing holes in the outer frame, each with 5 tons (tension belt attachment) 9 pairs of lashing mushrooms, embedded in the outer frame at the top and sides, each with 10 tons 2 x at the front on the bend 7 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the back, distance between the lashing eyes not greater than 1100 mm 3 additional pairs of folding lashing eyes, each with 10 tons 1 x on the bend (sticks out) 1 x at the beginning of the low bed, embedded inside on the longitudinal beams 1 x embedded in the floor behind the last axle Towbar with tested 50 mm towing eye Towbar height adjustment via spring Axles + suspension Drum brake axles, as selected by the manufacturer "Laser-measured axle/chassis" Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free Steel-rubber bearings and mechanical axle load compensation at the front and rear (rocker compensation) Wheels and tires 235 / 75 R 17.5" at the manufacturer's discretion Steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake 2 interchangeable coupling heads at the front, with connecting lines to the towing vehicle, 24 volt ABS and ALB, with ABS plug at the front, with connecting cable Caution: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrics 12-24 volts, multi-chamber LED lights, yellow LED lighting on the side, license plate lighting in LED, (Note! Incorrect diagnoses can occur with certain towing vehicles, although the function is present) 2 white position lights at the front in LED 2 white/red lane keeping lights at the rear in LED 2 x 7-pin, interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (light removable) 2 pairs of warning signs with double LED lighting and extendable

Condition: new, machine/vehicle number: 408ba9a39bbb8087056d6e563, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3,000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame Ncjdpsi Ri Daofx Aazer 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° / D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel housing area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of approval / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized

Condition: new, machine/vehicle number: 55d3c5c03e032385649769b1b, empty load weight: 9,900 kg, maximum load weight: 14,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box recessed in Incl. Turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings extendable to 3,000 mm (not in rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points, 10 tons each, integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm towing eye Please note! With 40 mm drawbar eye, the maximum permissible total weight of the truck is 18000 kg, otherwise 50 mm drawbar eye required. Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring jack support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany 1 with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Ncedpfx Aoi Ri I Eeazer Frame Ral 3002 carmine red 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: f79a9f15e7131d57a512793ab, empty load weight: 8,900 kg, maximum load weight: 15,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Widenings extendable to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing rings at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Nedpei Ri Izofx Aazscr Parabolic suspension with maintenance-free steel-rubber bearings and mechanical incl. axle load compensation front and rear Axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Front offset with steel/ checker plate covering Then with 70 mm softwood floor, steel/checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Operating instructions With 10,000 kg axle load, a special permit is required, only indivisible load possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany With Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Incl. Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized

Condition: new, empty load weight: 8,900 kg, maximum load weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,410 mm, loading space width: 2,550 mm, loading space height: 900 mm, total length: 11,940 mm, suspension: parabolic leaf (spring), tire size: 235/75R17,5, color: other, Year of construction: 2026, 4-axle low-loader trailer, hot-dip galvanized, extendable widening to 3000 mm. Steel ramps 3000 mm long, 750 mm wide, hydraulic operation with hydraulic lateral displacement. Excavator arm recess 1800 mm long, approx. 650 mm wide and 150 mm deep. Softwood floor 70 mm. Stock vehicle. Njdpsyxft Tsfx Aazocr

Condition: new, machine/vehicle number: 15431365fe5515297a6a9fb05, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope Ncodpfxei Ri A Sj Aazjr 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm Wooden planks 70 mm for widening to 3000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: used, maximum load weight: 31,500 kg, overall weight: 37,000 kg, axle configuration: 3 axles, first registration: 09/2010, loading space length: 12,440 mm, loading space width: 2,500 mm, Equipment: ABS, ID: 717149 LIFTING AXLE For more information please call: +420734511212 Ncedsy Eu Hpepfx Aazer

Condition: used, maximum load weight: 31,500 kg, overall weight: 37,000 kg, axle configuration: 3 axles, first registration: 09/2010, loading space length: 12,440 mm, loading space width: 2,500 mm, Equipment: ABS, LIFTING AXLE For more information please call: +420734511212 Nedpfjy Eu Hvsx Aazocr

Condition: used, axle configuration: 2 axles, Year of construction: 2020, Equipment: ABS, = Additional options and accessories = - Air suspension rear - Air suspension front = Notes = For inquiries about the vehicle, Mr. Seidel will assist you (by phone). Fliegl TPS 119 Flatbed Air suspension, 40 mm towing eye, Duomatic coupling, GFA axles, Knorr ABS, spring-loaded brakes, drive-on ramps, permissible gross weight: 11,900 kg, unladen weight: 3,250 kg, payload: 8,650 kg, cargo area dimensions: L 6,200 mm W 2,490 mm H 380 mm, tire tread depth: 1st axle 10 mm, 2nd axle 10 mm. Upon request, we can provide you with a leasing or financing offer. Mr. Seidel (phone) will be happy to assist you. For further information, please visit our homepage. ... Subject to errors, changes, and prior sale !!! - Ncjdey Ada Tepfx Aazsr = Further information = Unladen weight: 3,250 kg Payload: 8,650 kg Gross vehicle weight: 11,900 kg Cargo area dimensions (LxWxH): 6200x2490x380 Last inspection: 2026-07 Please contact Tobias Ebert for further information.

Condition: used, maximum load weight: 28,070 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 06/2014, next inspection (TÜV): 09/2026, loading space length: 13,650 mm, loading space width: 2,490 mm, loading space height: 2,990 mm, loading space volume: 102 m³, total width: 2,550 mm, total height: 4,000 mm, Equipment: ABS, FLIEGL SDS 350 MegaRunner RH 95, low fifth-wheel height - ranging from 930 mm to 950 mm, platform-curtain side body with side sliding tarpaulins, sliding roof, double-wing rear doors with rotating rod lock, rear mounting for forklift truck, EN 12642 Code XL load certificate, screen-printed floor, continuous lashing holes in external frame, 13 lashing rings per side, galvanized chassis, SAF landing gears, SAF axle(s), ABS, EBS, disc brake system, lift axle, air suspension with lifting/lowering feature, the vehicle may have advertising stickers and/or lettering. SI86658 Nedpoyrwirofx Aazocr Our offer generally excludes a new roadworthiness (TÜV) certificate. If a new TÜV certificate is required, we will be happy to provide you with an offer from our partner workshops! The vehicle may have advertising stickers and/or lettering. Our general terms and conditions of delivery and payment apply. We will gladly provide you with a financing or leasing offer for this item. Please do not hesitate to contact us!

Condition: new, machine/vehicle number: 0fe2184cda24503447c582a1e, empty load weight: 3 kg, maximum load weight: 34 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/55 r 22,5, Further information Chassis semi-trailer container Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Container mounts:1 x 40 feet with gooseneck tunnel The transportation of filled tank containers is excluded. Without rear height adjustment and without folding center supports, no transport of containers without tunnel possible. Container guide front plug-in 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EG Impact protection at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Nodpfxji Ri Ays Aazscr Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable clutch heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/55 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, rear and brake lights in LED, amber LED lighting on the side (Note! with certain towing vehicles, misdiagnosis may occur although the function is given) 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin socket at the front, without connecting cable LED work lights on both sides (switched via reversing light) Additional LED work light(s) at the rear, switched via reversing light Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Special approval required if the overall length of the train exceeds 16,500 mm. Attention: Transport of filled tank containers is excluded! Country of approval / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Support legs coated black Without pallet box Paint Attention: Archive pictures!

Condition: new, machine/vehicle number: 1e7fb50bfb3671204fb4d0b92, empty load weight: 4 kg, maximum load weight: 33 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/55 r22.5, Further information Chassis Saddle Container Fine-grained steel welded construction, saddle plate with interchangeable 2 kingpins and 2 kingpin positions Container mounts: 1 x 20 feet in the middle without steel/checker plate covering in the rear area 2 x 20 feet or 1 x 40 feet with gooseneck tunnel without height adjustment at the rear and without folding center supports, no transport of containers without tunnel possible. 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EG Impact protection at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/55 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, rear and brake lights in LED, amber LED lighting on the side (Note! with certain towing vehicles, misdiagnosis may occur, although the function is given) 2 white position lights at the front Ncedji Riv Nopfx Aazjr 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 2 additional LED work lights at the rear, switched via reversing light Operating instructions Attention: Transport of filled tank containers is excluded! Country of registration / plates Germany with Dekra approval and certificate (according to §13 EG - FGV) Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Attention: Archive pictures!

Condition: new, overall weight: 1,300 kg, loading space length: 3,100 mm, loading space width: 1,670 mm, loading space height: 1,980 mm, Year of construction: 2025, ANHÄNGERWIRTZ, your pick-up market for new trailers, offers top brand-name models! Over 850 new trailers in stock More than 130 used trailers always available Non-binding example: New Box Trailer Cargoboxx C400 Roadster 312x164x195 cm cargo space, 1300kg Pullman II V chassis, suitable for 100 km/h, GRP sandwich side walls with side door and central locking, aerodynamically shaped polyester front and roof in iron grey, aluminium plank floor and aluminium rear wing door & loading ramp combination, interior lighting, adjustable lashing rings, manoeuvring handle with automatic jockey wheel..... Sales around the clock via our trailershop Telephone order acceptance: Ncsdpfx Ajxtxrcsazsr MON. - FRI. 08:00 - 12:30 & 14:00 - 18:00 or 24/7 via trailershop Content and images are protected by copyright - logos are trademarked 10/25 ROADSTER4001300SWIIRGST

Condition: new, Year of construction: 2024, number of beds: 3, color: silver, total length: 5,970 mm, total width: 2,250 mm, total height: 2,610 mm, axle configuration: 1 axle, overall weight: 1,500 kg, empty load weight: 940 kg, operation weight: 982 kg, Equipment: onboard kitchen, T@B – The Timeless Classic T@B, the caravan with its distinctive silhouette in a modern retro design, turns heads and has long enjoyed cult status. Despite its compact form, it surprises with a remarkably spacious interior and smart details. Manufacturer's Suggested Retail Price: €31,147 – save €5,167 with our in-house discount! Optional Equipment: * Stabilizer safety coupling * Colour Kit METROPOLIS * Upgraded to 1,500 kg total weight * Alloy wheels * Luggage nets (7 pieces) * Insect protection door * Service hatch 70 x 30.5 cm, rear right * Decorative roof trim longitudinal/rear * Upholstery: ACTIVE ROCK * Sink covers and cutting board made of plastic * Shower device with fittings (removes the 230V socket in the washroom) * Ambient lighting Standard Equipment: * AL-KO chassis with trailing arm axle * 15" tires * Gas bottle storage box for 2 x 11 kg cylinders * Blackout and insect protection blinds on the windows * Smooth aluminum sheet side walls, silver * LED awning light * Furniture decor: Salem Ash and Lino * High-quality 3-burner cooker with cast grate and glass lid, deep sink * 98-liter absorption refrigerator * 12V air circulation system * TRUMA S 3004 gas heater with piezo ignition * 45-liter fresh water tank, permanently installed * TRUMA water heater with connection for kitchen and washroom (230V operation only) Njdpeyd Rbxefx Aazscr * Residual current circuit breaker (RCCB) * LED light strip under the kitchen wall cupboard ---- Ready for your next adventure? With our caravan, you always travel flexibly and independently. Whether relaxed weekend trips or unforgettable long journeys – Experience freedom! Do you have questions or would like to know more about this model? Feel free to contact us and let's plan your journey together. We are happy to provide advice and support, and help you find the perfect travel companion to suit your needs. We look forward to hearing from you! Best regards, Your Spürkel Sales Consultant Team The traditional company in Bochum. Model/Year: 2024, Internal ID: 10050_2122, Interior height: 198 cm, Body length: 472 cm, Unladen weight: 940 kg, Operational weight: 982 kg, Max. permissible weight: 1500 kg, Beds: transverse double bed, Sleeping areas: front (70 x 195 cm), rear (145 x 198 cm), Heater: TRUMA S 3004 heater with piezo ignition, Fridge volume: 98 l, Water supply: 45 l, Upholstery: ACTIVE ROCK, 230V sockets: 5, SERVICE HATCHES / GARAGE DOORS: Service hatch 70 x 30.5 cm, rear right, DOORS: insect protection door, MATERIALS / VEHICLE GRAPHICS: decorative roof trim longitudinal/rear, LIVING/SLEEPING/UPHOLSTERY AND FABRICS: Upholstery: ACTIVE ROCK, KITCHEN/BATHROOM: Shower device with fittings (removes the 230V socket in the washroom), ELECTRICS / MULTIMEDIA / SAFETY: ambient lighting, sink covers and plastic cutting board, CHASSIS / RUNNING GEAR / LOAD INCREASES: Stabilizer safety coupling, Colour Kit METROPOLIS, Weight upgrade to 1,500 kg (1,500 kg chassis), Alloy wheels, Luggage nets (7 pieces), VEHICLE DOCUMENTS: manual (German), Gas bottle stirage for 2 x 11 kg bottles, ACCESSORIES: 10-year water ingress guarantee, MediKit voucher, soap and detergent dispenser, WINDOWS / ROOF HATCHES / VENTILATION: High-quality double-glazed plastic windows with safety locks, blackout and insect blinds on windows, opening side windows.

Condition: new, overall weight: 1,300 kg, loading space length: 3,100 mm, loading space width: 1,670 mm, loading space height: 1,980 mm, Year of construction: 2025, ANHÄNGERWIRTZ—the collection market for your new trailer offers strong brand manufacturers! Over 850 new trailers in stock Over 130 used trailers constantly available Non-binding example: Sales around the clock via our trailer shop Sales & telephone order acceptance: Ncodpfewuld Rsx Aazor MON - FRI 08:00 - 12:30 & 14:00 - 18:00 Or 24/7 via the trailer shop Content and images are subject to copyright – logos trademarked 06/25

Condition: excellent (used), fuel type: diesel, color: yellow, lifting height: 18,000 mm, mast type: telescopic, Year of construction: 2019, operating hours: 664 h, General Information Year of manufacture: 2019 Technical Details Number of cylinders: 4 Drive: Wheel Unladen weight: 14,300 kg Functionality Mast: Telescopic (3-section) Mast length: 18 m Lifting capacity: 4,000 kg Ncodpfx Aajuxrv Tjzjr CE certification: yes Condition Technical condition: very good Visual condition: very good DIECI PEGASUS 40.18 400 EX DEMO TELESCOPIC HANDLER YEAR OF MANUFACTURE: 2019 DRIVE: 4X4X4 MAX. LIFTING CAPACITY: 4,000 KG MAX LIFTING CAPACITY AT 15.3 METERS: 500 KG MAX WORKING HEIGHT: 18 METERS EXTRA HYDRAULIC FUNCTIONS 400° ROTATION TYRES: 405/70/20 2X JOYSTICK CONTROL 1X RADIO REMOTE CONTROL CE CERTIFICATE KUBOTA ENGINE TYPE: V3800-T 4 CYLINDERS 101 HP WATER COOLING MAX. DRIVING SPEED: 30 KM/H PALLET FORK HOOK TYPE: BUB 2448 OWN WEIGHT: 60 KG MAX. CAPACITY: 4,000 KG LARGE HYDRAULIC WINCH TYPE: BUD 4475 OWN WEIGHT: 410 KG MAX. CAPACITY: 3,000 KG BUCKET VOLUME: 1.20 M3 ONLY 664 DEMO HOURS!!!!! FOLLOW US ON INSTAGRAM: GEURTSTRUCKS WE SPEAK GERMAN HABLAMOS ESPAÑOL WE SPEAK ENGLISH

Condition: used, Year of construction: 1980, operating hours: 17,400 h, Please provide reference number upon request: 22767 Nedpfx Aeyv U T Roazscr Specifications: 1980 model Hours: approximately 17,400 Weight: 12500 kg Worn tires Bucket Owner hasn't used it in years Ready for delivery     Description: 1980 Volvo 4400 wheel loader. The wheel loader starts but the transmission does not work Ready for delivery. Hours: 17400 Own weight: 12500 Model: 4400 hjullaster - delemaskin = More information = Please contact ATS Norway for more information

Condition: used, machine/vehicle number: WFDFLT3240100xxxx, Year of construction: 2019, Please provide reference number upon request: 23046 Ncedpfx Aasy Elmtszor Specifications: 2019 model Length: 998 cm Wheelbase: 136/136 cm Net weight: 4800 kg Max payload: 19,200 kg Owner has paid for the trailer Ready for delivery   Description: 2019 Fliegl 3 axle container trailer. The owner says he has gone over everything to make sure it is in good condition. Ready for delivery. Technical approved: Yes EU-approved until: 05.02.2027 Own weight: 4800 Total Weight: 19200 Model: 3 akslet container kjerre = More information = Please contact ATS Norway for more information

Condition: good (used), axle configuration: 3 axles, first registration: 03/2021, loading space length: 13,600 mm, loading space width: 2,480 mm, loading space height: 3,010 mm, total length: 13,900 mm, total width: 2,550 mm, total height: 4,100 mm, suspension: air, tire size: 435/50R19,5, color: other, Year of construction: 2021, Equipment: ABS, = Additional Options and Accessories = - EBS - Lifting roof = Notes = Number of axles: 3, Unladen weight: 6,015 kg, Gross weight: 39,000 kg, Chassis type: Full chassis, Chassis material: Steel, Kingpin size: 2 inch, Suspension type: Air suspension, ABS, EBS, Year of body construction: 2021, Lifting roof, Sliding roof, Axle type: SAF = Further Information = General Information Cabin: Day cab Registration number: KLEYN1 Drivetrain Fuel type: Diesel Transmission Gearbox: Manual transmission Axle configuration Tire size: 435/50R19.5 Brakes: Disc brakes Suspension: Air suspension Axle 1: Left tire tread: 5 mm; Right tire tread: 5 mm Axle 2: Twin tires; Left outer tire tread: 9 mm; Right inner tire tread: 9 mm Axle 3: Left tire tread: 6 mm; Right tire tread: 4 mm Weights Curb weight: 6,015 kg Payload: 32,985 kg GVW: 39,000 kg Functional Sliding roof: Yes Environment Emission class: Euro 0 Condition Technical condition: good Visual condition: good Damages: none Ncedpfxoy Hcnqo Aazor = Company Information = Kleyn Trucks is one of the world's largest independent dealers of used vehicles. Here, you can choose from a constantly changing stock of 1,200 used trucks, tractors, and trailers. Our inventory includes all European brands, years, and price ranges. Why buy from Kleyn Trucks? Simple! • Large, fast-changing inventory • Recognized quality • Competitive pricing • Reliable business practices • We speak many languages • We understand our customers • Assistance with import and transport • (Export) plates can be arranged quickly • Professional technical services • The safety of 'recognized quality' • And more.... Please visit our website for special offers and the complete inventory. Leasing via Kleyn Trucks is possible in most European countries! Quickly calculate your leasing rate and send an inquiry through our website. Ask directly about our European warranty package.