Low loader trailer

FLIEGL VTS 400 Tieflader mit Radmulden Luft/ Hydr.

Condition: new, * BTT 131.80V cable drum trailer for hire / price on request Crjdpfxepugqge Aafsi BTT 131.80V hydraulically extendable delivery to the construction site by truck and instruction The expansion of renewable energy, e.g. offshore wind farms and their connection, is leading to a massive expansion of the grid. Instead of overhead lines, high-voltage cables with large conductor cross-sections are laid in the ground. In order to lay the longest possible lengths in one piece, cable manufacturers have started to supply the cables on wide drums so that they cannot be laid using conventional cable trolleys. The BTT 131.80 cable drum transport trailer can be hydraulically widened. Thanks to the air suspension, the trailer can be lowered sideways to adapt to inclined drums on difficult terrain. The U-shaped design, which is open at the rear, enables the use of a modified drawbar triangle in which the hydraulic cylinders for the widening function are housed. Simple widening of the vehicle and the drum drive using the trailer hydraulics Lock the vehicle frame at the required width with locking bolts ready Drum axles are carried on the trailer in the appropriate lengths BTT 131.80V in folded condition Widening The overall width of the trailers when folded is 2550 mm in accordance with the German Road Traffic Licensing Regulations (StVZO). In the construction site area, the trailer can be widened to a maximum of 4000 mm. The clear loading width is thus increased from 1690 mm to 3090 mm. (The dimensions may vary depending on the trailer type). The drum drive is split and is automatically taken along with the widening.

Condition: new, empty load weight: 9,650 kg, maximum load weight: 30,350 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,740 mm, loading space width: 2,550 mm, suspension: air, tire size: 235/75 r17,5 zoll, Year of construction: 2026, Equipment: ABS, center pivot plate, 4-AXLE LOW LOADER IN TOP CONDITION! => HOT-DIPPED GALVANISED (CHASSIS FRAME, TURNTABLE FRAME, RAMP) => FULL AIR SUSPENSION => WITH LIFTING AND LOWERING FUNCTION (REAR AXLE UNIT!) => SAF LOW LOADER AXLES => LASHING PACKAGE => HOLE-PUNCHED OUTER FRAME FOR ADDITIONAL LASHING POINTS => CLIMBING STRIPS IN THE REAR AREA OF THE RAMP => 6 LASHING POINTS IN THE EXCAVATOR ARM RECESS IN THE REAR AREA => LONG, ONE-PIECE RAMPS => SHALLOW RAMP ANGLE Permissible total weight 40,000 kg Payload approx. 30,350 kg Chassis frame hot-dip galvanised Turntable frame hot-dip galvanised Ramps hot-dip galvanised Air suspension SAF axle with drum brake EBS electronic braking system Tyres 235/75R17.5 – 16 ply Low bed length approx. 7160 mm Recess for excavator arm storage, approx. 3000 mm x 730 mm x 180 mm in the rear area of the low bed 4 pairs of recessed lashing rings 10 tonnes in the low bed 2 pairs of recessed lashing rings 10 tonnes in the upper bed 4 pairs of lashing points 3 tonnes in the outer frame of the low bed 3 pairs of lashing eyes 6 tonnes on the outer frame 4 pairs of spar pockets in the outer frame of the upper bed 4 pairs of spar pockets in the outer frame of the low bed 3-metre widening kit with folding outriggers without slope 4 x warning signs with lighting Rotating beacon at the rear LARGE STEEL STORAGE BOX under the loading platform 2 storage compartments with folding lids in the upper platform Hydraulic ramp lifters One-piece ramp approx. 3150 x 750 mm Softwood flooring for loading platform and ramps Crsdpfjhvxgzjx Aafei 40,000 kg GVW only with special permit according to §70 => Delivery costs: 2.90 euros plus VAT per km => Prices are ex D-86368 - Gersthofen Your direct contact: Mr. Hauptmann Tel. DOLL VEHICLE CONSTRUCTION *Subject to prior sale and changes!* *Price valid ex D-86368 - Gersthofen* *Sale only to commercial customers!* *Images may vary and are for general guidance only => may include/show accessories at an additional cost*

Condition: new, empty load weight: 408 kg, maximum load weight: 1,018 kg, overall weight: 1,350 kg, loading space length: 2,500 mm, loading space width: 1,565 mm, loading space height: 150 mm, loading space volume: 0.8 m³, color: other, construction height: 660 mm, working width: 2,250 mm, Manufacturer: Humbaur Type: Lowering trailer HKT 132515 S Permissible total weight: 1350 kg Payload: 1018 kg Unladen weight: 332 kg Box dimensions: 2500 x 1565 x 150 mm Cjdpogf Nbtefx Aafori Tire size: 195/50 R13C Loading height: 420 mm - Bolted, hot-dip galvanized chassis - Loading platform can be lowered hydraulically - Mechanical safety locking of the pivoting axle during operation - Humbaur multi-function lighting - With rear drive-over peak - License plate holder at the rear, can be swiveled away for loading - 15 mm thick wooden floor - Aluminum side walls, 150 mm high, with 4 pairs of integrated lashing straps - Tensile force 400 kg per lashing strap, Dekra tested - Attachment options at all corners for e.g. tarpaulin frame Options: 100 km/h approval €150 Tarpaulin and bow, internal loading height 160 cm €899 Tarpaulin and bow, internal loading height 180 cm €999 Tarpaulin and bow, internal loading height 200 cm €1099 Tarpaulin color can be chosen freely Motorcycle ramp ACE Bikes €150 Price includes vehicle registration document (Part II and COC papers) We have a large number of trailers from the following manufacturers in stock: Brenderup, Humbaur, Hapert, Brian James Trailers, Unsinn and Neptun. Upon request, we will provide you with a free transfer license plate. We repair trailers from all manufacturers. Further accessories available upon request. Subject to technical changes, price changes and errors. No liability is accepted for errors and printing errors. Features: Reversing aid, rubber spring axle, access ramp, tilting loading platform, support wheel, side marker lights, bolted, hot-dip galvanized chassis, braked, incl. warranty, loading platform can be lowered hydraulically, mechanical safety locking of the pivoting axle during operation, Humbaur multi-function lighting, with rear drive-over peak, license plate holder at the rear, can be swiveled away for loading, 15 mm thick wooden floor, aluminum side walls, 150 mm high, with 4 pairs of integrated lashing straps (tensile force 400 kg per lashing strap, Dekra tested), attachment options at all corners for e.g. tarpaulin frame, 13-pin plug and reversing light.

Condition: used, empty load weight: 9,400 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 03/2024, next inspection (TÜV): 03/2027, loading space length: 9,450 mm, suspension: air, tire size: 235/75 R17,5, color: red, Equipment: ABS, EBS Drum brake Loading area width 2,550 mm / 3,000 mm Payload 30,600 kg Electro-hydraulic pump unit with NATO connector Hydraulic ramps with lateral movement Crsdpfxjzzdx Ds Aafsi Hydraulic support legs SAF axles Excavator bucket body Extendable to 3 m Loading edge height 910 mm New price: €72,000.00 net Subject to change.

Condition: new, maximum load weight: 30,010 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,000 mm, loading space width: 2,520 mm, loading space height: 900 mm, total width: 2,550 mm, Brand-new Fliegl 4-axle low-bed trailer with wheel recesses and split ramps, type VTS 400 RM Hire-purchase offer: 48-month term, down payment only the VAT, final residual value 40% Monthly rate: EUR 899.00 Vehicle / Body: Low-bed trailer First registration: New vehicle Gross weight: 24,000kg/40,000kg Unladen weight: 9,990kg Payload: 14,010kg / 30,010kg Overall length: 12,000mm Loading length: total approx. 10,000mm, gooseneck approx. 2,850mm, load bed including rear taper approx. 7,150mm Width: 2,550mm Loading height: 900mm Further information Chassis: Low-bed trailer Steel welded construction Turntable with heavy-duty ball race Foldable rear support Wheel chocks with holders Aluminum side underrun protection Full-width rear spray flap Half-shell mudguards 1st and 2nd axle with anti-spray mud flaps behind each axle, anti-spray mud flap behind the 4th axle Excavator arm trough above rear axles, from the rear axle to the rear approx. 1,800mm long, approx. 650mm wide and 150mm deep 2 pairs of lashing holes, each 5t, in the excavator arm trough, on the longitudinal frame approx. 300mm from the front and approx. 200mm before the rear taper Spare wheel bracket for 1 spare wheel, upright on the gooseneck, front center, spare wheel brand same as main equipment, steel rim Toolbox let into the floor on the gooseneck with lid, W=720mm / L=520mm / D=170mm 1st pair of wheel recesses after the gooseneck, let into the deep deck in the driving lane, chamfered for access, length at the bottom approx. 1,600mm, approx. 400mm deep. Note! Frame in the main beam area 400mm higher than the wheel recess. 2nd pair of wheel recesses between the axles, let into the deep deck in the driving lane, chamfered for access, length at the bottom approx. 600mm, approx. 300mm deep. Note! Frame in the main beam area 300mm higher than the wheel recess. Extensions retractable to 3,000mm (no extension at the rear taper and not in the wheel recesses below) (track width of machines or vehicles to be transported must not exceed the outer frame width of 2,550mm) Storage compartment for timber planks underneath the low-bed deck 70mm timber planks for extension to 3,000mm Lashing points – low-bed trailer 1 pair of RIN lashing rings inlaid at the front on the gooseneck, each 5t 4 pairs of lashing holes in the outer frame, each 5t (for securing strap attachments) 8 pairs of lashing mushrooms flush-mounted top and side in the outer frame, each 10t 2 at the front on the gooseneck 6 in the deep deck First lashing ring 250mm from the front, last a maximum of 250mm from the rear, spacing between lashing rings not more than 1,100mm 5 pairs of stake pockets inlaid in the outer frame, inner dimensions 70 x 40mm (convertible to 5t ring lashing eyes, not included) 1 pair of foldable lashing rings additionally inlaid in the floor, each 10t 1 inside next to main frame at start of low-bed section 2 pairs of additional foldable lashing rings, each 10t 1 on the gooseneck (protrudes) 1 behind the last axle inlaid in the floor Credpfx Aaotrizkjfji Towing device for turntable trailer Drawbar with certified 50mm towing eye, towing eye inclined by 8° D-value at least 160kN Axles and Suspension BPW drum braked axles "Axles/chassis laser aligned" – reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical front axle load equalization (rocker equalizer) Wheels and Tires 235 / 75 R 17.5" Manufacturer’s choice, with M + S marking Steel rims in twin arrangement,

Condition: new, maximum load weight: 30,740 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting and lowering device and RtR valve * SmarD on-board system for load weight determination * Warning sign packages front & rear * Reflective contour tape on sides and rear * Removable rotating beacon at the rear * LED lights * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated steel and spare wheel holder in basket design, mounted on the right side * Enclosed plastic single fenders at the front * Straight steel mudguards at the rear, each with spray suppression (anti-spray system) * Side underrun protection * Turntable platform extended by 520 mm with 45° corners and 3 integrated storage compartments incl. cover, lockable * Chassis made of high-strength fine-grained steel * Floor over turntable platform made of 50 mm softwood, in the low-bed platform made of 60 mm softwood * Outer planks of the loading ramps made of hardwood * 4 stake pockets on each side (no stakes included) with simultaneous 2 t lashing point per pocket * Load securing package consisting of: 2 lashing points 6.4 t at the front left and right on the main frame of the turntable platform * 2 pairs of 13.4 t lashing rings each at the outer frame front and rear, as well as 4 pairs of 10 t lashing rings per side, swiveling and retractable * Loadable in all directions and recessed into the outer frame * 2 pairs of 6.4 t lashing rings in the excavator arm rest area * 8 pairs of galvanized swing-out marker boards for 3 m total width (not at the rear slope) * Widening planks stored in a compartment on the left side * Excavator arm rest above rear axle up to end of approach ramp approx. 2,100 x 740 x 190 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically adjustable tip, approx. 4,650 x 720 mm incl. hydraulic lateral ramp shifting and load-holding valve * Loading area across the turntable: approx. 2,990 x 2,520 mm Credpfx Asl Tik Noafei * Rear loading area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, turntable, access ramps, flip-out marker boards and mechanical drop-down supports hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in black * Tires: 235/75 R 17.5 * New vehicle without first registration, with manufacturer warranty * Subject to errors and prior sale * Immediately available ex Egestorf on the A7

Condition: used, empty load weight: 8,940 kg, maximum load weight: 31,060 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 03/2026, loading space length: 10,250 mm, loading space width: 2,520 mm, loading space height: 930 mm, suspension: air, tire size: 235/75R17.5, color: silver, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 4 axles, turntable, air suspension, ABS (anti-lock braking system), can be widened to 3m, lashing eyes, hydraulic ramps, rear support, side aluminum wheel guards, twin tires, wheel recesses. Superstructure: 4-axle low-bed trailer with wheel recesses, excavator arm recess, and hydraulic ramps. Galvanized, 4x 10t axle, drum brakes, technically permissible total weight 40,000 kg, can be widened to 3000mm! Length of upper platform approx. 2800mm! Length of lower platform approx. 7450mm! Ramp length approx. 2900mm! Loading height of front wheel recess approx. 550mm! Loading height of rear wheel recess approx. 620mm! Codpfx Aajzr Rmisfsri Length of front wheel recess approx. 1600mm! Length of rear wheel recess approx. 600mm! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale, and errors!