Low loader semitrailer

FAYMONVILLE MAX Trailer MAX100 Semi-Tieflader

Condition: used, maximum load weight: 34,030 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 07/2025, next inspection (TÜV): 07/2027, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and in the short term, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: Gooseneck with rear slope, approximately 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring, approximately 30 mm thick. Loading platform: Loading platform can be hydraulically raised and lowered after the gooseneck, length approximately 2,800 mm, with rear slope approximately 1,000 mm x 8°. 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN). 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 1 pair of lashing rings that can be folded inwards on the center beam at the front (LC 10,000 daN). Grid floor C40/4 (point load approximately 2.3 t on an area of approximately 20 x 20 cm) above the axles. Diamond-plate floor. Two-piece steel ramps: One pair of galvanized two-piece steel ramps in reinforced design, approximately 3,185 + 1,420 x 1,250 mm, with grid floor C40/5 (point load approximately 8 t on an area of approximately 20 x 20 cm). Ramp with hydraulically raising and folding ramp sections and hydraulic lifting mechanism, maximum load per pair: 40,000 kg. In accordance with Regulation 1230/2012/EU, ramps with a length of less than 300 mm do not need to be taken into account in the vehicle length of 16,500 mm when in the driving position. Landing gear: JOST landing gear (mechanical) with 2-speed gearbox for approximately 24 t lifting capacity (approximately 50 t test load). Pgjdpszu Ebtjfx Aagsr Tires: 235/75 R 17.5 3PMSF TPMS tire pressure monitoring system according to ECE R 141 Axles: BPW axles and suspension. 2 axles rigid, 1 axle steered. Technical axle load: 12,000 kg each. Electro-magnetic parking brake via reverse gear and can also be activated manually. Air suspension with raising and lowering valve. Braking system: WABCO braking system according to EU regulations with EBS-E (2S2M). Colors: Semitrailer RAL 3002 carmine red. Rims silver. Tarpaulin in RAL 9006 silver. Including accessories: 1 spare wheel holder under the loading platform on the right in the direction of travel. 2-inch King Pin. One galvanized steel front panel. Yellow-red air couplings on the galvanized connection strip at the front. 4 wheel chocks with holder on the front panel. 3 height-adjustable wooden planks. Galvanized folding supports under the slope of the loading platform. Height-adjustable tarpaulin superstructure *3,960 mm*. Galvanized front panel with a tensioning mechanism for the sliding curtains. Roof from EDSCHA, height-adjustable by approximately 400 mm, can be moved forward on aluminum roof rail profiles (screwed to the front and rear walls). 3 pairs of adjustable load securing bars in the loading platform. The superstructure can be widened by approximately 750 mm on the left and right at the rear by hydraulic means. Sliding tarpaulin with approximately 700 mm reserve in length, with lashing straps at intervals of approximately 600 mm. Top edge of the superstructure approximately 3,960 mm (loaded). Driving with an open sliding tarpaulin is not permitted and will result in damage to the tarpaulin. On the diamond plates on the gooseneck and on the loading platform, a sand layer is applied as an anti-slip coating. Cover plates to bridge the gap between the ramps and the loading platform. Electro-hydraulic unit at the rear under the loading platform. On the gooseneck and on the ramps, one holde

Condition: new, maximum load weight: 39,600 kg, overall weight: 49,500 kg, axle configuration: 3 axles, total width: 2,540 mm, total height: 860 mm, MAX Trailer Type 100 NEW | Extendable | 39t Payload | 3 Axles | from €66,900 New vehicle – individually configurable to your specific application. High payload capacity with robust construction and maximum economic efficiency. ----Highlights: • Approx. 39,600 kg payload • Loading platform: 8,600 mm + extendable by 5,400 mm • Ramp load up to 40,000 kg • BPW axles with air suspension • WABCO EBS braking system ----Technical Data: • Gross vehicle weight: 49,500 kg • Unladen weight: approx. 9,866 kg • Loading height at max. load: approx. 860 mm • Total width: 2,540 mm • Top speed: 80 km/h ----Standard Equipment: • Extendable loading platform with robust hardwood floor • Galvanised steel ramps with hydraulic lift • High-strength steel chassis with durable corrosion protection • LED lighting system Pgedpfxoypa Nps Aagsr • JOST landing gears with 2-speed gearbox • Tyre pressure monitoring system (TPMS) ----Included Options: • Spare wheel with holder • Galvanised front wall (approx. 400 mm) • Electro-hydraulic unit under the loading platform • Extendable warning signs with LED • Reflective tape in accordance with EU regulations • Beacon bracket at the rear • Control valves for ramps, right side Further equipment and bespoke configurations available on request – we tailor your vehicle to your exact requirements. Sample photo. Equipment may vary depending on configuration.

Condition: new, maximum load weight: 36,020 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our full vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Complete equipment details available on request. Gooseneck: * Gooseneck with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area with rear bevel approx. 1,000 mm x 8° * 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) * 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate above the axles Two-piece steel ramps: * One pair of galvanized two-piece steel ramps, approx. 3,185 + 1,420 x 1,250 mm, with grating covering C40/5 (point load approx. 2.8 t on a surface of approx. 20 x 20 cm) * Ramp with hydraulically foldable ramp sections and hydraulic lifting system * Maximum load per pair: 30,000 kg Pgedpjy Auhujfx Aagor Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 steering trailing axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock activated via reverse gear and manually * Air suspension with raise/lower valve Tyres: * Tyres 235/75 R 17.5 3PMSF – brand at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Brake system: * WABCO brake system compliant with EU regulations, with EBS-E (2S2M), without connection lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations, LED lighting 24V ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * HRM metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to guarantee optimum corrosion protection * Finishing coat: 2 layers 2K topcoat, solid colour RAL 3002 carmine red as per RAL system 841GL * Rear section metallised and painted RAL 9010 (pure white) * Rims in silver Included accessories: * One bracket for warning signs on the gooseneck and at the rear left and right, including socket * 1 spare wheel holder under the loading area, right in the direction of travel * 2" kingpin * One galvanized steel front wall * Yellow-red air couplings on the galvanized front connection bar * 4 wheel chocks with brackets on the bulkhead * 3 height wooden boards * Galvanized folding supports under the loading area bevel * Bracket for rotating beacon at rear of trailer * Height-adjustable tarpaulin structure – approx. 3,960 mm * Galvanized front wall with tensioning system for sliding curtains, height adjustable by approx. 400 mm * EDSCHA roof, sliding forward on aluminum roof girder profiles (screwed to front and rear wall) * 3 pairs of sliding stakes in the loading area * The body is hydraulically extendable to the left and right at the rear by approx. 750 mm * Sliding roof with pivoting portal crossbeam * Sliding curtain with approx. 700 mm reserve length, ratchet straps at approx. 600 mm intervals. Height O

Condition: new, maximum load weight: 37,075 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available on request. Gooseneck: * Gooseneck with front corners beveled approx. 45° and rear taper approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN). Hardwood floor approx. 30 mm thick Loading area: * Loading area after the gooseneck hydraulically liftable/lowerable, length approx. 2,800 mm, with rear taper approx. 1,000 mm x 8° * 6 pairs of folding outward lashing rings (LC 5,000 daN) * 2 pairs of folding outward lashing rings (LC 10,000 daN) * 1 pair of inward folding lashing rings at the front central beam (LC 10,000 daN) * Cutouts in the external frame of the loading area for attaching tension belts (LC 2,000 daN) * Grating surface C40/4 (point load approx. 2.3 t on an area of approx. 20 x 20 cm), over the axles checker plate Two-piece steel ramps: * One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with C40/4 grating (point load approx. 2.2 t on an area of approx. 20 x 20 cm) * Ramp with hydraulically folding in/out ramp sections. Hydraulic lift system, hydraulically adjustable * Maximum load per pair: approx. 40,000 kg Landing gear: * JOST landing gear (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock via reverse gear and manual activation * Air suspension with lift and lower valve Brake system: * WABCO brake system according to EU regulations with EBS-E (2S2M) Tyres: 235/75 R 17.5 3PMSF – Manufacturer of our choice TPMS: * TPMS tire pressure monitoring system in accordance with ECE R 141 Paintwork: * HRM metalizing of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for optimal corrosion protection * Final paint in 2 coats of 2K topcoat, solid color in RAL 3002 Carmine Red in accordance with RAL system 841GL * Rims in silver grey Pedoyhkqzjpfx Aagegr Including accessories: * 2-inch kingpin * One galvanized steel front wall, approx. 400 mm high * Grating in the gooseneck taper C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * Grating in rear taper of the loading area C40/4 (point load approx. 3.4 t on an area of approx. 20 x 20 cm) * Non-slip sand paint on the checker plates above kingpin and loading area * Electro-hydraulic unit at the rear under the loading area * On the gooseneck: plug-in aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). The rear galvanized drop-in stakes are removable. (Body length approx. 2,560 mm) * An electric cable winch with radio remote control, approx. 5,400 kg pulling force, including approx. 9.5 mm thick steel cable, approx. 24 m long, with cable guide pulley * Bolted 5 t ring for cable winch deflection on the neck without deflection pulley * One galvanized toolbox integrated in the beveled gooseneck with opening for a winch * Grating on the gooseneck C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading area * Lift axle on the front axle with control via TEBS E depending on current axle load and loading condition * 7 pairs comple...

Condition: new, maximum load weight: 38,140 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from equipment. Full equipment details available on request. Gooseneck: - Gooseneck with front corners chamfered approx. 45° and rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, approx. 30 mm thick Loading area: - Telescopic loading area with rear incline approx. 1,000 mm x 8° - Between 1st and 2nd axle: one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized cover over wheel recesses (width approx. 670 mm – max. point load 5 t / pc.) - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 4 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - Cutouts in the outer frame for attaching tie-down straps (LC 2,000 daN) Landing legs: - JOST landing legs (manual) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Pgjdew Tpq Dspfx Aagjr Tyres: - Tyres 235/75 R17.5 3PMSF, make at our discretion - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transfer to the towing vehicle via standardised EBS interface as per ISO 11992 - For correct display, the towing vehicle must be able to receive and display this data Axles: - BPW axles and suspension, 2 axles rigid, 3rd axle self-steering - Technical axle load: 12,000 kg - Electromagnetic reverse lockout activated automatically when reversing and manually - Air suspension with lifting and lowering valve. Axle tools Braking system: - WABCO braking system according to EU regulations with EBS-E (2S2M) without piping to the tractor unit Electrical system: - Electrical system per EU regulations - LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets, according to ISO; 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: - Steel structure made of high-strength fine-grained steels - Steel qualities: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure automatically shot-blasted after welding in a wheel-blasting system - Second shot-blasting with corundum for optimum coating adhesion - HRM metallization of entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection - Final painting with 2 layers of 2K topcoat, single-colour in RAL 3002 Carmine Red, rear section metallized and painted in RAL 9010 Pure White - Metallic finish not available - Paint structure tested in salt spray test according to ISO 9227-NSS - Internal cavities sealed with special wax Including the following accessories: - On the gooseneck and rear, left and right, one holder for warning signs each, including socket - Spare wheel holder in front of the front wall (without spare wheel) - 2-inch king pin - Galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection bar - Galvanized folding supports under the inclination at the rear of the loading area - A hardwood crash protection strip at the rear wall from gooseneck to the loading area - 1 pair of recessed lashing rings along the central beam at the rear inclination (LC 10,000 daN) - Aluminium drop sides and tailgate on the gooseneck

Condition: new, maximum load weight: 47,300 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, loading space length: 8,600 mm, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately and at short notice, on our website. Excerpt from the equipment list. Full specifications available on request. Gooseneck: * Gooseneck with beveled front corners (approx. 45°) and rear bevel (approx. 750 mm x 10°) * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Extendable loading platform with rear bevel (approx. 1,000 mm x 8°) * 5 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Cutouts in the outer frame of the loading area for hooking tensioning straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick; over the axles, diamond plate surface Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox, 24t lifting capacity (50t test load) Tyres: * 235/75 R 17.5 3PMSF tyres, brand at our discretion Axles: * BPW axles, two rigid axles, two trailing steering axles, air-suspended, with drum brakes, lifting/lowering function * Steering axles with electromagnetically-activated reverse lock (via reverse gear or manually) * Axle tools Pgodpfoyvnfgex Aagjr Brake system: * WABCO brake system in accordance with EU regulations with EBS-E (4S3M), no connecting lines to the tractor unit Steel structure: * Steel construction from high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield 355 MPa) S690QL/S700MC (yield 690 MPa) Electrical system: * Electrical system compliant with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets (ISO standard: 24N - ISO 1185, 24S - ISO 3731, 15-pin - ISO 12098) Paintwork: * Premium and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc-rich primer * High-quality 2-component (2K) single-color topcoat RAL 3002 Carmine Red * Rear section metallized and painted in RAL 9010 (Pure White) * Rims in silver Accessories: * Spare wheel holder in front of the bulkhead (without spare wheel) * 2 inch kingpin * Galvanized steel front wall approx. 400 mm high * Yellow-red air couplings on the galvanized front connection bar * Receptacle at the rear of the gooseneck for ALU loading ramps * Galvanized drop-down supports under the loading area bevel * Bracket for a revolving beacon at the rear of the trailer * Brackets left and right on the gooseneck and rear plate for warning signs including socket * TPMS tire pressure monitoring system compliant with ECE R 141 * Removable ALU sideboards and rear wall on the gooseneck, approx. 2,440 x 400 mm (L x H); rear galvanized insert posts are removable (body length approx. 2,560 mm) * Galvanized toolbox integrated in the beveled gooseneck * 3 pairs of WADER container locks in the loading platform for one 20' (30') or one 40' container * Sliding hook-in rails for ALU loading ramps at the rear of the vehicle * 6 pairs of pockets for plug-in posts, approx. 100 x 50 mm in the outer frame of the loading area * Galvanized extensions, extendable by approx. 230 mm per side * Lift axle on the front axle with TEBS E control based on current axle load and load status * 2 LED reversing lights mounted on the rear plate * 2 pairs of ferry-

Condition: new, maximum load weight: 37,075 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including immediately available and short-term delivery vehicles, on our website. Sample of the equipment. Full equipment details available on request. Neck (Gooseneck): * Gooseneck with front corners bevelled approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading Platform: * Loading area behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear bevel approx. 1,000 mm x 8° * 6 pairs of external foldable lashing rings (LC 5,000 daN) * 2 pairs of external foldable lashing rings (LC 10,000 daN) * 1 pair of internal foldable lashing rings at the central beam front (LC 10,000 daN) * Cut-outs in the outer frame of the platform for hooking in tensioning straps (LC 2,000 daN) * Grating flooring C40/4 (point load approx. 2.3 t over an area of approx. 20 x 20 cm), treadplate flooring over the axles Two-piece Steel Ramps: * One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with grating surface C40/4 (point load approx. 2.2 t over an area of approx. 20 x 20 cm) * Ramp with hydraulically folding ramp sections * Hydraulic lift unit, hydraulically adjustable * Maximum load per pair: approx. 40,000 kg Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lift capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 fixed axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reversing lock automatic via reverse gear and manual activation * Air suspension with lift and lower valve Braking System: * WABCO braking system in compliance with EU regulations with EBS-E (2S2M) Tyres: Tyres 235/75 R 17.5 3PMSF – make at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Paintwork: * HRM metallisation of the complete vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminium) to ensure maximum corrosion protection * Final coating with 2 layers of 2K topcoat, single-coloured in RAL 3002 Carmine Red as per RAL System 841GL * Rims in silver grey Accessories included: * 2-inch king pin * Galvanized steel front wall approx. 400 mm high * Grating in the gooseneck bevel C30/3 (point load approx. 2 t over an area of approx. 20 x 20 cm) * Grating in the platform bevel C40/4 (point load approx. 3.4 t over an area of approx. 20 x 20 cm) * Electric-hydraulic unit at the rear under the platform * Plug-in aluminium side and rear boards on the gooseneck, approx. 2,440 x 400 mm (L x H). Rear galvanized insert stanchions removable. (Body length approx. 2,560 mm) * Electric winch with radio remote control, approx. 5,400 kg lifting capacity, including approx. 9.5 mm thick steel cable, approx. 24 m long, with cable guide roller * Bolted approx. 5 t ring for winch cable loop on the neck without deflection pulley * One galvanized toolbox integrated in the sloped gooseneck with opening for a winch * Grating on the gooseneck C30/3 (point load approx. 2 t over an area of approx. 20 x 20 cm) * 7 pairs of stanchion sockets for plug-in stanchions, approx. 100 x 50 mm, in the outer frame of the platform * Lift axle on the front axle, controlled by TEBS E depending on actual axle load and current loading status Podpfxoyhkrre Aagogr * 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 2 pairs in the lift bed, 5 pairs in the rear section of the platform

Condition: new, maximum load weight: 39,720 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Sample equipment features. Full specification upon request. Gooseneck * With beveled front corners approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approx. 30 mm thick Loading Platform Loading platform in extendable design * 5 pairs of fold-out outer lashing rings (LC 5,000 daN) * 3 pairs of fold-out outer lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Recesses in the outer frame of the loading platform for securing straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, over axles with chequer plate covering Landing Gear * JOST (mechanical) with 2-speed gearbox, approx. 24 t lift capacity (approx. 50 t test load) Axles * BPW axles: 2 fixed axles, 2 steering axles, drum brakes * Air suspension with lift/lower function * Self-steering axle with electro-magnetic reverse lock, activated via reverse gear or manually * Tires: 205/65 R 17.5 Brake System * Wabco brake system in accordance with EU directives with EBS-E (4S3M), without interconnecting lines to the tractor unit Steel Construction * Made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Paintwork * First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer * High-quality 2-component (2K) top coat, single-color, RAL 3002 Carmine Red * Rear section metallized and painted in RAL 9010 (Pure White) * Rims in silver Accessories Included * 2-inch king pin * Galvanized front steel bulkhead approx. 400 mm high * Spare wheel holder in front of bulkhead Podpou Sd U Ujfx Aagogr * Yellow-red air couplings on galvanized connector bar front * 4 wheel chocks with holder at bulkhead * Bracket at rear of gooseneck for aluminum loading ramps * Galvanized folding supports under inclined edge of loading platform * Holder for beacon at rear of trailer * Yellow reflective tape on sides, extension, and rear in accordance with EU regulations * Brackets for warning signs with socket on both sides at the gooseneck and rear panel * TPMS tire pressure monitoring system per ECE R 141. Data transmission to the tractor unit via standardized EBS interface according to ISO 11992; for correct display, the tractor unit must support data transmission and display * Plug-in aluminum side walls and tailgate on gooseneck, approx. 2,440 x 400 mm (L x H); rear galvanized stakes are removable (body length approx. 2,560 mm) * Galvanized toolbox, integrated in gooseneck slope * 6 pairs of WADER container locks in loading platform, for 1 x 20' container, 2 x 20' containers or 1 x 40' container * Sliding mounting rails for aluminum ramps at rear of vehicle * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm, in the outer frame of the loading platform * Galvanized cross bracket under the loading platform * Galvanized extendable widenings, extendable approx. 230 mm per side * Lift axle on front axle, controlled via TEBS E according to current axle load and load status * 5 pairs of recessed lashing rings along the central beam (LC 5,000 daN)