Lowbed semitrailer for transportation of construction machinery

Nükte - CETRATEK 4 Lowbed Semi-Trailer

Condition: new, empty load weight: 17,250 kg, maximum load weight: 48,700 kg, overall weight: 66,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,480 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 17,250 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and removed hydraulically -For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Low bed: -Low bed with external supports, designed as a telescopic tank bridge in low construction with extension at the front -Length x width approx. 7,550 mm x 2,740 mm -Mechanical locking of the extension Chassis: -Chassis at the rear with closed outer frame -Checker plate covering and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, suspension and tires: -"PENDEL-AXLE", all axles hydromechanically forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint in a single color in "FAY-Gray-34-0260" -Technical axle load 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 Accessories: -Steel bulkhead, plug-in, approx. 400 mm high -4 wheel chocks -Gooseneck in the rear upper area closed with a removable cover -1 pair of steel ramps with climbing strips and fastening bolts to bridge the hooks of the low bed -The ramps can be placed over or between the hooks -Fastening options for the steel ramps at the rear between the outer supports of the gooseneck -One Locking point approximately every 1,000 mm on the extension -1 lashing ring on the left and right on the front cross member -Connection strip for supply lines to the tractor unit, attached at the height of the outer frame profile -6 pairs of threaded blocks on the outside of the inner supports of the loading area for mounting screwable rings M24 -6 pairs of countersunk lashing rings on the outside of the outer supports of the loading area, foldable inwards and outwards -1 pair of threaded blocks at the front and rear of the outer supports of the loading area for mounting screwable rings M24 -Hanging strip for loose aluminum loading ramps on the vehicle's end cross member -Central lubrication system with 2 pumps, BEKAMAX brand -Steering from the front and rear, operated by cable remote control, with alignment control of the axles -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Removable loading floor (galvanized) in 3 elements can be inserted between the outer supports with hardwood flooring -Foldable extensions, by approx. 230 mm per side -Extension planks, loose, framed in steel Bwjdpfoh Hm Tzox Acvsl -4 warning signs approx. 423 x 423 mm -Radio remote control for operating the steering -3.5" king pin -Anti-slip sticker on the left bevel of the gooseneck -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Guide plate from the gooseneck for the fifth wheel plate, approx. 800 mm wide -1 spare wheel with mounting adapter -Parking position on the gooseneck for the warning signs when not in use -2 pairs of stake pockets embedded in the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm -Dipper handle recess of the rear chassis closed at the back with a plug-in plate -Color of the trailer MB 7350 Novagrau

Condition: used, functionality: fully functional, empty load weight: 16,300 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, first registration: 08/2018, suspension: other, tire size: 205/65 R 17,5, color: green, Equipment: ABS, EBS, - 5 axles: 1st axle friction-steered and liftable; 2nd–5th axle hydraulically steered Bsdpfxsymnmwo Acvswl - Extendable: 6,200 mm (total length: 12,800 mm – 19,000 mm) - SAF axles - Sliding hydraulic double ramps with support legs - Lifting and lowering device - Drum brakes - Suspension: air-lift Errors and omissions excepted.

Condition: used, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 04/2000, next inspection (TÜV): 10/2026, Year of construction: 2000, Without MAN tractor unit Bwjdsyhrqcjpfx Acvsl

Condition: like new (used), functionality: fully functional, empty load weight: 14,900 kg, axle configuration: 3 axles, permissible axle load (axle 1): 12,000 kg, permissible axle load (axle 2): 12,000 kg, permissible axle load (axle 3): 12,000 kg, first registration: 09/2025, color: red, Year of construction: 2025, The trailer is being sold in combination with the Volvo FH16-750. The vehicle can be extended by up to 4.05 m. It is equipped with a long material support as well as two hydraulic loading ramps. Bwodey H Agajpfx Acvjl

Condition: new, Year of construction: 2024, Equipment: ABS, = Further options and accessories = - Electronic braking system (EBS) - Lifting axis - Spare wheel Bwedpfxsy E Nxas Acvjl = Notes = TECHNICAL SPECIFICATIONS MEASURES & DIMENSIONS -Gross Vehicle Weight (kg): 70,000 -Loading Platform Length (mm) : 9,000 -Weight of Axle Group (kg): 48,000 -Total Lenght (mm): 13,550 -Kingpin Capacity (kg) :22,000 -Total Width (mm): 2,550 -Curb Weight (kg): 13,000 -Loading Platform Height (mm): 920 -Pay Load (kg): 57,000 -Height of 5th Wheel (mm) : 1,310 CONSTRUCTIONS -Base chassis -Heavy duty and extra durability designed BOX type chassis All welded S355 steel chassis -Outer frame is UPE 240 profile -Welding (Chassis) : Automatic ARC submerged -Welding (Superstructure): Automatic robot welding -Axle (Type) : Özkoç Trax or Osman Koç Turkish Brand -Drum brakes 4 x 12 Ton axles -Axle Lifting: 1st axle automatic 4th axle manual lifting -Suspension (Type): Air Suspension -Steering Axles :- -King pin (Type) : 1 position with 1x coupling-pen 2” -Tires: 16+1 units, 245 / 70 R 17.5 -Rims: 16+1 units, 6.75 x 17.5 steel rims -Landing Gear: Mechanically operated by one side, two speed -Brake System: Wabco EBS (4S/3M) with RSS according to EC Directive with ADR Adaptation -Brake Chamber -2 axles with 4 units emergency brake chambers. -2 axles with 4 units service brake chambers. Electric system -24V, 2x7 + 1x15 pin sockets, according to SAE standard with ADR Adaptation SABA Brand -2 x Rear Stop Lights. - 4 x Side LED Lights -2 x White LED Lights - 2 x Front LED Lights -2 x Registration Plate Lights - 2 x rotating Lights Floor -Above tires and edges of platform are covered checkered sheet and hard wood -The middle surface is covered by flat sheet steel Rear loading ramps -Hydraulic operated rear ramps with Electro pump for rear ramps hydraulic function with cable -push button for remote control -Folding type rear ramps length 2500 mm +1500 mm width 900 mm -Rear ramps are sliding internal and external hydraulic -Short steel ramps behind neck. Paint Application -Sand Blasting, Chemical cleaning, HYZINC covering, Epoxy covering and 2 coats of acrylic paint TECHNICAL SPECIFICATIONS ACCESSORIES -2 x 8 pcs of heavy duty lashing rings mounted on the outer frame mushroom type -4 x Certificated Expray mud flaps. -1 x Plastic water tank -2 x Wheel chocks and holders -2 x 8 Galvanized side extensions brackets 250 mm + 250 mm -2 x Side Protections, aluminum -1 x tool box. -1 x spare wheel carrier with 1 tire (on the gooseneck) -2 x manual support legs at the rear. -2 x Reflective tape and reflector sign at the rear and sides. -2 x side extension reflectors -Steel front panel(height:400mm) -Aluminum side panels on gooseneck section(height:400mm) -1 plaque places on rear ramps or bumpers = Further information = Curb weight: 13,000 kg CE marking: yes

Condition: used, maximum load weight: 49,900 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, first registration: 01/2020, next inspection (TÜV): 01/2027, with air suspension, hydromechanical forced steering, single-extendable load platform, wheel recess, with rear bevel and loading ramps Dimension B: 11,300 mm Unladen weight: 15,100 kg STZ-L gooseneck - Robust steel welded construction - Formed load platform: 3,900 x 2,480 mm - Hydromechanical forced steering (dual-circuit steering) - 5th wheel plate with ball bearing slewing ring and interchangeable 2" king pin, with adjustable steering wedge - Mechanical landing legs at the front Load platform - Single-telescoping, designed as an outer-inner tube construction with a 300 mm fixed front deck section - 300 mm sliding table on the inner tube, adjustable and lockable - Extension stage locking via spring-applied cylinder and conical locking pin - 1 pair of wheel recesses after the 1st axle, depth 410 mm Chassis - 4-axle, air-suspended chassis - 1st axle liftable and steered in the forward direction - SAF axle assemblies, consisting of three hydromechanically forced-steered stub axles - Axles with adjustable tapered roller bearings and automatic brake rod adjusters (AGS) - Standard raise/lower valve for lowering to min. 805 mm or raising to max. 1,050 mm - Loading height: 860 mm - Excavator arm recess: 3,850 mm long, 750 mm wide - Wheel recess after gooseneck: 410 mm deep - Wheel recess after the 1st axle: 410 mm deep Vehicle rear - "Bevelled" design at 500 mm - Short rear overhang: 1,240 mm measured from the center of the last axle - Hydraulic rear supports Loading ramps - 2-piece ramps, length: 2,855 mm / 1,415 mm, width: 890 mm - Hydraulically adjustable ramps Braking system - 2-line full air brake system with diaphragm brake cylinders - Automatic load-sensing brake (ALB) - Automatic brake rod adjusters (AGS) - Parking brake via spring-applied cylinders - Anti-lock braking system (ABS) Special equipment - Wheel recess - Excavator arm recess - Extendable widenings - Central lubrication system "BekaMax" - Electric power unit with radio remote control Technical data Gooseneck Load platform (LxW): 3,900 x 2,480 mm 1,000 mm Wirtgen slope Bedpfsy Iq Tdox Acvewl Fifth wheel height when loaded: 1,250 mm Load platform Load platform (LxW): 8,800 x 2,550 mm Telescoping extension: 2,800 mm Stepwise extension to (LxW): 11,600 x 2,550 mm Steering 1st axle liftable and steered in forward direction 2nd-4th axle hydromechanically force-steered (dual-circuit steering) Radio remote control Electric power unit

Condition: used, maximum load weight: 56,200 kg, overall weight: 69,800 kg, axle configuration: > 3 axles, first registration: 10/2021, loading space length: 12,500 mm, loading space width: 2,550 mm, total width: 2,550 mm, total height: 3,625 mm, Year of construction: 2021, Equipment: ABS, FYAMONVILLE 4 (2+2)-axle MULTIMAX low-loader semi-trailer, air-suspended, with 2 self-steering trailing axles Type: Multi-N-4(2+2)L-AUM-18AT-8.80-17.5-2.54-RM German trailer, one owner 4.1m telescopic, fully hydraulic ramps and supports, wheel recesses, extendable width, ALLOY WHEELS FULLY EQUIPPED!!! Gooseneck: Gooseneck SNT design approx. 3.7m, slope approx. 1,000 mm x 10° Loading platform: Extendable loading platform, length approx. 8.8m, slope approx. 500 mm x 10° Excavator stick recess approx. 2490x750x210 mm Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps can be hydraulically shifted individually approx. 235 mm outward and approx. 215 mm inward Axles and suspension: 4x BPW axles 12t, 2 fixed, 2 trailing self-steering axles Electromagnetic reverse lock Reverse gear + manual Air suspension raise & lower valve Tyres: 235/75 R17.5 3PMSF MICHELIN or PIRELLI Load Index: 143/141J (144/144F), spare wheel NEW 16x ALLOY WHEELS, POWDER COATED WABCO braking system, EBS-E EU regulations 24-volt lighting system ASPÖCK-NORDIK ASPÖCK-UNIBOX sockets 24N, 24S & 15-pin PAINTWORK Standard HRM metallisation of the outer frame Complete steel construction shot-blasted, ARC-GALVANIZED with ZINACOR 850 (zinc 85% - aluminum 15%) hot-finished Steel structure: Steel qualities: * S355J2+N/S355MC (yield strength 355MPa) * S690QL/S700MC (yield strength 690MPa) * Welders certified per DIN-EN 287-1 * MAG welding process according to EN ISO 4063 * Protective gas M21 according to EN ISO 14175 Accessories: Removable front wall made of steel, approx. 400 mm high * NATO socket + spiral cable * 3 kW electro-hydraulic power unit for hydraulic operations * Spare wheel holder on the front wall * Attachment holes for screw-in lashing rings * The first hole approx. 200 mm from the front, then approx. every 400 mm * 2 pairs of screw-in lashing rings (LC 5,000 daN) * Fastening hole at the rear upper area of the outer beams * 1 pair of screw-in lashing rings (LC 10,000 daN) * Gooseneck with approx. 40 mm thick hardwood covering * 1 pair of removable aluminium side boards, aluminium rear board approx. 400 mm high, anodised * 2'' kingpin * Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide * 4 wheel chocks with holders * Mounting for aluminium approach ramps * JOST mechanical landing legs with 2-speed gearbox and crank * Continuous loading platform, hardwood floor approx. 50 mm thick, interrupted between the axles * Securing the loading platform with conically welded locking profiles, 250 mm incl. pre-tensioning plate * Slotted holes at the front of the loading platform for suspended and repositionable bridging elements * 1 intermediate table with stepped loading platform, approx. 300 mm wide for the extension tube * Front and rear with slotted holes for suspended or repositionable bridging elements * Removable cover level with the loading platform Bedpey Iq Arjfx Acvowl * Extensions extendable by approx. 230 mm each side * 1 pair of permanently installed open wheel recesses up to the extension, approx. 700 x 410 mm, in the loading platform before the 1st axle * Covers for the wheel recesses longitudinally divided, with wooden support, exterior with plug-in locks * Wheel recesses with sheet metal covering and 15 x 15 mm square climbing strips every approx. 200 mm * Between the 2nd and 3rd axle in the platform a pair of permanently installed wheel recesses * Rubber floor "Super Grip" 25 mm and 5 mm steel floor as additional reinf

Condition: new, Year of construction: 2024, Equipment: ABS, = Further options and accessories = - Electronic braking system (EBS) - Lifting axis - Spare wheel = Notes = TECHNICAL SPECIFICATIONS MEASURES & DIMENSIONS -Gross Vehicle Weight (kg): 70,000 -Loading Platform Length (mm) : 9,000 -Weight of Axle Group (kg): 48,000 -Total Lenght (mm): 13,550 -Kingpin Capacity (kg) :22,000 -Total Width (mm): 2,550 -Curb Weight (kg): 13,000 -Loading Platform Height (mm): 920 -Pay Load (kg): 57,000 -Height of 5th Wheel (mm) : 1,310 CONSTRUCTIONS -Base chassis -Heavy duty and extra durability designed BOX type chassis All welded S355 steel chassis -Outer frame is UPE 240 profile -Welding (Chassis) : Automatic ARC submerged -Welding (Superstructure): Automatic robot welding -Axle (Type) : Özkoç Trax or Osman Koç Turkish Brand -Drum brakes 4 x 12 Ton axles -Axle Lifting: 1st axle automatic 4th axle manual lifting -Suspension (Type): Air Suspension -Steering Axles :- -King pin (Type) : 1 position with 1x coupling-pen 2” -Tires: 16+1 units, 245 / 70 R 17.5 -Rims: 16+1 units, 6.75 x 17.5 steel rims -Landing Gear: Mechanically operated by one side, two speed -Brake System: Wabco EBS (4S/3M) with RSS according to EC Directive with ADR Adaptation -Brake Chamber -2 axles with 4 units emergency brake chambers. -2 axles with 4 units service brake chambers. Electric system -24V, 2x7 + 1x15 pin sockets, according to SAE standard with ADR Adaptation SABA Brand -2 x Rear Stop Lights. - 4 x Side LED Lights -2 x White LED Lights - 2 x Front LED Lights -2 x Registration Plate Lights - 2 x rotating Lights Floor -Above tires and edges of platform are covered checkered sheet and hard wood -The middle surface is covered by flat sheet steel Rear loading ramps -Hydraulic operated rear ramps with Electro pump for rear ramps hydraulic function with cable -push button for remote control -Folding type rear ramps length 2500 mm +1500 mm width 900 mm -Rear ramps are sliding internal and external hydraulic -Short steel ramps behind neck. Paint Application -Sand Blasting, Chemical cleaning, HYZINC covering, Epoxy covering and 2 coats of acrylic paint Bedpfsyil Ihjx Acvowl TECHNICAL SPECIFICATIONS ACCESSORIES -2 x 8 pcs of heavy duty lashing rings mounted on the outer frame mushroom type -4 x Certificated Expray mud flaps. -1 x Plastic water tank -2 x Wheel chocks and holders -2 x 8 Galvanized side extensions brackets 250 mm + 250 mm -2 x Side Protections, aluminum -1 x tool box. -1 x spare wheel carrier with 1 tire (on the gooseneck) -2 x manual support legs at the rear. -2 x Reflective tape and reflector sign at the rear and sides. -2 x side extension reflectors -Steel front panel(height:400mm) -Aluminum side panels on gooseneck section(height:400mm) -1 plaque places on rear ramps or bumpers = Further information = Curb weight: 13,000 kg CE marking: yes