Low loader trailer

Raptor Trailer 2-3-4 Axles Remorque Trailers

Condition: new, maximum load weight: 30,310 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, NEW VEHICLE Fliegl 4-axle low loader with 2 pairs of wheel recesses and ramps Total weight 40,000 kg Payload 30,310 kg Empty weight 9,690 kg Blsdpfx Ahenzlg Doyor Total length 12,000 mm Loading length 10,000 mm Loading bed 7,150 mm including 850 mm approach slope Loading height 900 mm 1st pair of wheel recesses after offset in the loading bed, bottom length approx. 1,600 mm, 400 mm deep 2nd pair of wheel recesses between the axles in the loading bed, bottom length 600 mm, 300 mm deep Extensions to 3,000 mm, warning signs, rotating beacon, large lashing package 5 pairs of stake pockets in the outer frame Excavator arm recess 1,800 mm long, 150 mm deep Drawbar 50 mm Air suspension with lifting and lowering valve, can be operated separately BPW drum brakes Tires 235 / 75 R 17.5" Axle load detection via EBS CAN bus signal, Trailer Info Center Ramps 2,800 mm x 750 mm with hydraulic actuation Hydraulic side shift Rent-purchase offer: term 48 months, residual value 40%, down payment only VAT on the rental rates, monthly rate EUR 970.00 net Vehicle will be available from September 11th, 2023 from the Neumünster trade fair. Visit us at Nordbau - Stand West 121 right next to the main entrance. Other 3, 4 and 5 axle low loaders new and used available immediately

Condition: new, maximum load weight: 30,010 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,000 mm, loading space width: 2,520 mm, loading space height: 900 mm, total width: 2,550 mm, Brand-new Fliegl 4-axle low-bed trailer with wheel recesses and split ramps, type VTS 400 RM Hire-purchase offer: 48-month term, down payment only the VAT, final residual value 40% Monthly rate: EUR 899.00 Vehicle / Body: Low-bed trailer First registration: New vehicle Gross weight: 24,000kg/40,000kg Unladen weight: 9,990kg Payload: 14,010kg / 30,010kg Overall length: 12,000mm Loading length: total approx. 10,000mm, gooseneck approx. 2,850mm, load bed including rear taper approx. 7,150mm Width: 2,550mm Loading height: 900mm Further information Chassis: Low-bed trailer Steel welded construction Turntable with heavy-duty ball race Foldable rear support Wheel chocks with holders Aluminum side underrun protection Full-width rear spray flap Half-shell mudguards 1st and 2nd axle with anti-spray mud flaps behind each axle, anti-spray mud flap behind the 4th axle Excavator arm trough above rear axles, from the rear axle to the rear approx. 1,800mm long, approx. 650mm wide and 150mm deep 2 pairs of lashing holes, each 5t, in the excavator arm trough, on the longitudinal frame approx. 300mm from the front and approx. 200mm before the rear taper Spare wheel bracket for 1 spare wheel, upright on the gooseneck, front center, spare wheel brand same as main equipment, steel rim Toolbox let into the floor on the gooseneck with lid, W=720mm / L=520mm / D=170mm 1st pair of wheel recesses after the gooseneck, let into the deep deck in the driving lane, chamfered for access, length at the bottom approx. 1,600mm, approx. 400mm deep. Note! Frame in the main beam area 400mm higher than the wheel recess. 2nd pair of wheel recesses between the axles, let into the deep deck in the driving lane, chamfered for access, length at the bottom approx. 600mm, approx. 300mm deep. Note! Frame in the main beam area 300mm higher than the wheel recess. Extensions retractable to 3,000mm (no extension at the rear taper and not in the wheel recesses below) (track width of machines or vehicles to be transported must not exceed the outer frame width of 2,550mm) Storage compartment for timber planks underneath the low-bed deck 70mm timber planks for extension to 3,000mm Lashing points – low-bed trailer 1 pair of RIN lashing rings inlaid at the front on the gooseneck, each 5t 4 pairs of lashing holes in the outer frame, each 5t (for securing strap attachments) 8 pairs of lashing mushrooms flush-mounted top and side in the outer frame, each 10t 2 at the front on the gooseneck 6 in the deep deck First lashing ring 250mm from the front, last a maximum of 250mm from the rear, spacing between lashing rings not more than 1,100mm 5 pairs of stake pockets inlaid in the outer frame, inner dimensions 70 x 40mm (convertible to 5t ring lashing eyes, not included) Bedpjtrizksfx Ahyjlr 1 pair of foldable lashing rings additionally inlaid in the floor, each 10t 1 inside next to main frame at start of low-bed section 2 pairs of additional foldable lashing rings, each 10t 1 on the gooseneck (protrudes) 1 behind the last axle inlaid in the floor Towing device for turntable trailer Drawbar with certified 50mm towing eye, towing eye inclined by 8° D-value at least 160kN Axles and Suspension BPW drum braked axles "Axles/chassis laser aligned" – reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical front axle load equalization (rocker equalizer) Wheels and Tires 235 / 75 R 17.5" Manufacturer’s choice, with M + S marking Steel rims in twin arrangement,

Condition: new, maximum load weight: 30,740 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, * T 4: * Wabco EBS-E (electronic brake system) * RDÜ Tire Pressure Monitoring System * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lift and lowering function and RtR valve Bljdpfx Ahol Tik Nsyor * Smard-Board for load weight determination * Warning sign packages front & rear * Contour tape on sides and rear, reflective * Removable rotating beacon at the rear * LED lighting * Straight drawbar with 50 mm tow eye and infinitely adjustable height * Tool box made of powder-coated steel sheet and spare wheel holder in basket design, right side * Front closed single plastic fenders * Rear straight steel mudguards with spray suppression (anti-spray) * Lateral underrun protection * Turntable platform extension by 520 mm with 45° corners and 3 integrated lockable compartments incl. lids * Chassis made of high-strength fine-grained steel * Floor over turntable platform made of 50 mm and on low-bed platform of 60 mm softwood * Outer planks of the drive-on ramps made of hardwood * Four stake pockets per side (no stakes included) with simultaneous 2 t lashing option * Load securing package consisting of: 2 lashing eyes 6.4 t at front left and right on the main frame of the turntable platform * Per side at front and rear, 2 pairs of 13.4 t lashing rings on the outer frame; per side, 4 pairs of 10 t lashing rings, swiveling and lowerable * Loadable in all directions, recessed into the outer frame * 2 pairs of 6.4 t lashing rings on the side in the excavator arm support * 8 pairs of galvanized folding outriggers for a total width of 3 m (not in the rear slope) * Widening planks stored in a compartment on the left side * Excavator arm resting area above the rear axle up to end of approach slope approx. 2,100 x 740 x 190 mm * Mechanical drop supports at rear * Hydraulic folding ramps with hydraulically adjustable ramp tip approx. 4,650 x 720 mm including hydraulic ramp side shift & load-holding valve * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, turntable, ramps, folding outriggers, and mechanical drop supports hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in black tone * Tires 235/75 R 17.5 * New vehicle without initial registration with manufacturer's warranty * Subject to errors and prior sale * Available from CW 07/2025