Swap body semitrailer

Abrollcontainer Container 6,5 m Kran Fassi F150

Condition: new, loading space length: 5,300 mm, loading space width: 2,300 mm, total length: 6,500 mm, Year of construction: 2026, Brand new roll-off container with FASSI loading crane ELLERMANN roll-off container according to DIN 30722-1 Standard container Type S 77 with crane platform Internal dimensions: approx. 6.5/5.3 x 2.3 x 2.0 meters (all dimensions are approximate) Usable volume: approx. 24 m³ Paint finish: RAL 7016 (anthracite gray) ? Mounting brackets for hook lift systems according to DIN 30722-1 (15,000 kg) with rear outer rollers and subframe made of INP 180 Outer rollers are greaseable and replaceable Mounting bracket Ø 50 mm, hook height 1,570 mm Transition from the subframe to the end wall support is reinforced with 10 mm knee plates ? Crane platform 20 mm thick on the end face, length approx. 1,200 mm Reinforcement on the end wall support and subframe on the inside Additional stiffening on the end support ? Crane cutout on the end wall (according to Fassi drawings) ? Bottom pan made of 5 mm St 37.2 (S235JR) ? Side walls made of 3 mm St 37.2 (S235JR) ? Rounded bottom pan, raised approx. 250 mm towards the side wall ? End profile made of sturdy round tube Ø 90 mm ? Spant spacing 750 mm Spant profile U 80 x 50 mm ? On both sides, 1 x transverse spant in the middle, fully welded ? Double-wing door at the rear with Dutch door latch and lateral safety central locking system according to UVV Safety central locking system extended to 2,000 mm Door latch with container door opening aid and hockey lock Additional opening handle on the left door leaf ? All-around tarpaulin and net hooks ? Container primed once on the inside, primed twice on the outside and painted twice in a single color on the outside ? UVV stickers with safety instructions ? Container inspected and approved according to DGUV Rule 214-017 (formerly BGR 186) ? Container inspection book (digitized) for documenting the required annual recurring inspection according to UVV FASSI loading crane F150A.2 e-dynamic Design according to CE directive (EN 12999) The equipment manufacturer must carry out the inspection when the loading crane has been mounted in its final position and is ready for operation. Base unit: F150A.2 e-dynamic Slewing range 416° all hydraulic cylinders are double-acting piston rods are hard-chrome plated double knee joint system with PROLINK (over-extension of the knuckle arm up to 15°) electronic overload shut-off device with FX500 6 functions RCH or RCS radio remote control (linear levers) with display and XP system emergency shut-off and optical alarm (90% and 100%) including digital slewing limitation, adjustable FASSI stability control FSC incl. LMB II pressure relief and load holding valves, high-pressure filter Danfoss S800 control block with 4 control valves, operable on one side separate hydraulic tank (90 l) with filter, mounted on the crane base extendable on both sides, support width 4.60 m, hydraulic support ? CE, incl. M.O.L. Standard color RAL 3020 traffic red - all cylinders painted black load hook and attachment brackets (short / 500 mm) Transport position: folded across the direction of travel Dead point above the support beam Note: Observe on-board voltage / 12V or 24V, standard 24V F150A.2.23 e-dynamic » Base unit IE742 connection box Support spread to support width 5.4 m Move dead point 1 LED work spotlight on the knuckle arm » mounted LED for 2 outriggers, not mounted » (crane) Control system for 2 additional functions with » 2 hose lines / eactive Slewing valve, only for cranes with rack and pinion Quick-action valve for the outriggers Additional cos Hsdpfx Akezq Iu Ujcer