Open semitrailer with tarp

KRONE SDP 27*Mega*SAF*LiftA*LenkA*StaplerH

Condition: used, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 05/2020, next inspection (TÜV): 10/2026, loading space length: 13,620 mm, loading space width: 2,480 mm, loading space height: 3,000 mm, total width: 2,550 mm, total height: 4,000 mm, Equipment: ABS, Distance from kingpin to center of support device: 2,267 mm Fifth wheel height unladen: 980 mm Double T-shaped longitudinal and center beams, as well as crossbeams and outriggers, welded together Outer frame with Multilock outer frame, universal load securing option every 100 mm Front height: 80 mm (incl. floor and fifth wheel plate) Hnedpfozf T Tlsx Agnep 2" kingpin (corner dimension: 2,040 mm) Rear underrun protection device according to EC directive, for cargo box length: 13,620 mm i.w. for cargo box width 2,480 mm i.w. 3 axles, each with a load capacity of 9,000 kg Aggregate distance = 7,900 mm Wheelbase: 1,310 / 1,310 mm with center alignment SAF axles, 19.5", with air suspension (total travel 260 mm) and disc brake (ET 120) Brake disc with a diameter of 370 mm Tire size: 6-ply, 445/45 R 19.5, tread depths: 9/13 mm 12/13 mm 13/7 mm with lifting and lowering device, incl. automatic ride height adjustment load-dependent, fully automatic electronic lift axle control for the 1st axle manual function on the control panel for forced lifting (= starting aid according to Directive 97/27/EC) and forced lowering Preparation of the lift/trailing axle(s) for operation from the tractor unit (without tractor unit installation), according to the selected light connector(s), for control via Note: The vehicle does not operate in the BO power circuit when the 1st axle is lifted! The lift axle may only be used as a starting aid according to Directive 97/27/EC! SAF, air-suspended aggregate + trailing axle Attention: reduced ground clearance in the area of the lift axle! Loading height limited by pallet stop Cargo box width in the area of the pallet stop reduced to: 2,460 mm i.w. Rear forklift bracket for accompanying forklift (incl. forklift pockets, underrun protection according to ECE-R58 and 2 pieces of retaining brackets for securing chains on the outside) Tire size of accompanying forklift max.: 23" Design of the attachment bracket: spar bracket with pneumatic actuation Bolted counterweight attached to the front end (required when transporting the accompanying forklift) Dimensions of the support spars: 100 x 100 x 10 x 1500 mm Dimensions of the forklift pockets: 200x100x5x1200 mm Center distance of the forklift pockets: 380 mm Width of the folded-down underrun protection: 1340 mm Forklift pockets flush with the end crossbeam at the rear. Rear socket: 15-pole DIN ISO 12098 uneven load distribution! Type: BO 13620 30 mm thick, waterproof floor panel, cut surfaces sealed all around, continuous, waterproof bonding between chassis and floor panel with permanently elastic high-performance adhesive. Strength according to DIN EN 283, for floor loads up to a maximum of 7,000 kg forklift axle load. Tear plate embedded in the floor panel at the rear (4x450mm) Type: AB 13620 AGG Dimensions 13,620 mm i.w. x Width i.w. see spars LM universal outer posts, continuous, for attaching sliding tarp and sliding spars Edscha sliding tarp (175) with plastic joints, height 175 mm, slope 0 mm, designed for the transport of grid boxes according to DIN 15155 Height i.w. bottom edge of outer post at the front side: 2,860 mm Height i.w. bottom edge of outer post at the rear side: 2,860 mm Height i.w. bottom edge of cross spar in the middle: 3,000 mm Loading height in the rear portal: 2,845 mm unladen overall vehicle height at the highest point approx. 4095 mm hydraulic lift roof with a total travel of 500 mm, can be raised separately at 4 corner spars Structure height at the front can be lowered b