Open semitrailer with tarp

KRONE SDP 27*Mega*SAF*LiftA*LenkA*StaplerH

Distance from kingpin to center of support device: 2,267 mm
Fifth wheel height unladen: 980 mm
Double T-shaped longitudinal and center beams, as well as crossbeams and outriggers, welded together
Outer frame with
Multilock outer frame, universal load securing option every 100 mm
Front height: 80 mm (incl. floor and fifth wheel plate)
2" kingpin (corner dimension: 2,040 mm)
Rear underrun protection device according to EC directive,
for cargo box length: 13,620 mm i.w.
for cargo box width 2,480 mm i.w.
3 axles, each with a load capacity of 9,000 kg
Aggregate distance = 7,900 mm
Wheelbase: 1,310 / 1,310 mm
with center alignment
SAF axles, 19.5", with air suspension (total travel 260 mm)
and disc brake (ET 120)
Brake disc with a diameter of 370 mm
Tire size: 6-ply, 445/45 R 19.5,
tread depths:
9/13 mm
12/13 mm
13/7 mm
with lifting and lowering device, incl. automatic
ride height adjustment
load-dependent, fully automatic electronic
lift axle control for the 1st axle
manual function on the control panel for forced lifting
(= starting aid according to Directive 97/27/EC) and forced lowering
Preparation of the lift/trailing axle(s) for operation
from the tractor unit (without tractor unit installation),
according to the selected light connector(s),
for control via
Note: The vehicle does not operate in the
BO power circuit when the 1st axle is lifted! The lift axle may only be used as a starting aid according to
Directive 97/27/EC!
SAF, air-suspended aggregate + trailing axle
Attention: reduced ground clearance in the area of the lift axle!
Loading height limited by pallet stop
Ledpfx Ajzf T Tloldsac
Cargo box width in the area of the pallet stop
reduced to: 2,460 mm i.w.
Rear forklift bracket
for accompanying forklift (incl. forklift pockets, underrun protection according to ECE-R58 and 2 pieces of retaining brackets for securing chains on the outside)
Tire size of accompanying forklift max.: 23"
Design of the attachment bracket: spar bracket with pneumatic actuation
Bolted counterweight attached to the front end (required when transporting the accompanying forklift)
Dimensions of the support spars: 100 x 100 x 10 x 1500 mm
Dimensions of the forklift pockets: 200x100x5x1200 mm
Center distance of the forklift pockets: 380 mm
Width of the folded-down underrun protection: 1340 mm
Forklift pockets flush with the end crossbeam at the rear.
Rear socket: 15-pole DIN ISO 12098
uneven load distribution!
Type: BO 13620
30 mm thick, waterproof floor panel, cut surfaces
sealed all around, continuous, waterproof bonding
between chassis and floor panel with permanently elastic high-performance adhesive. Strength according to DIN EN 283, for floor loads up to a maximum of 7,000 kg forklift axle load.
Tear plate embedded in the floor panel at the rear (4x450mm)
Type: AB 13620 AGG Dimensions 13,620 mm i.w. x Width i.w.
see spars
LM universal outer posts, continuous, for attaching
sliding tarp and sliding spars
Edscha sliding tarp (175) with plastic joints,
height 175 mm, slope 0 mm, designed for the
transport of grid boxes according to DIN 15155
Height i.w. bottom edge of outer post at the front side: 2,860 mm
Height i.w. bottom edge of outer post at the rear side: 2,860 mm
Height i.w. bottom edge of cross spar in the middle: 3,000 mm
Loading height in the rear portal: 2,845 mm
unladen overall vehicle height at the highest point approx. 4095 mm
hydraulic lift roof with a total travel of 500 mm,
can be raised separately at 4 corner spars
Structure height at the front can be lowered b

The listing was translated automatically. Translation errors are possible.