Tipper semitrailer

STAS S300CX MultiSTAR 53m³ ALU Mulde*Kombitür*

Condition: new, axle configuration: 3 axles, loading space length: 10,636 mm, loading space width: 2,480 mm, loading space height: 2,300 mm, loading space volume: 60 m³, Chassis manufactured using a self-supporting aluminum construction with corresponding reinforcements in the lower belt for particularly high stability and strength, component chassis made of ALUMINUM, 140 mm frame height! (max. 39 tons) Axles and Suspension "Disc brake 22.5" Jost axle assemblies, 3 x 9 tons with DC air suspension, lifting and lowering function, Wabco Smartboard, electronic brake wear indicator (BVA) for display in the central control unit (without central control unit equipment), 1st + 3rd axles can be lifted separately with an assistance function (without central control unit equipment), 3rd axle additionally equipped with Optiturn, ECAS air suspension, tire pressure monitoring Wabco Trailerpulse with ZF rim-mounted sensors Tires and Wheels 6 wheels with tires size 385/65 R 22.5, manufacturer's choice, Alcoa aluminum rims DuraBright-11, 75x22.5 ET 120 kingpin screwed into a 10 mm thick plate Fifth Wheel Aluminum swivel landing gear, 2 x 10 tons support load, for air suspension, we use swivel feet Braking System According to E.G. standard, two-line braking system, EBS E-system Wabco with RSS system (Roll Stability Support), spring brake system acting on two axles with operation at the rear, aluminum air tank system, premium modulator Electrical System According to STVZO guidelines with 2 LED five-chamber lights type Aspöck Europoint LED integrated in the aluminum rear panel, 24-volt system with 1x 5-pole and 2x 7-pole socket, with side marker lights in LED design, 2 separate LED work lights at the rear, 2 LED work lights on the side starting at the 1st axle, at the height of the fifth wheel supports, 1 LED work light inside, at the front left, operated from the outside Rjdpfjfakkcsx Ap Decf Body/Tipping Body "Body fully welded inside" Front wall load 17,250 dkn, rear and side walls 10,250/13,400 dkn, aluminum tipping body, side walls 30 mm thick aluminum plank profiles (2-3 mm) 600 mm wide, completely welded with lower and upper belts, plank profiles fully welded inside, floor laid as a sliding floor system on 140 mm aluminum cross members, floor load approx. 7 tons/m2, cross members mounted at a relatively close spacing (approx. 350 mm), aluminum front wall with 600 mm plank profile, 2-3 mm thick in a straight design, special aluminum corner profiles in a beveled design, smooth rear wall in a straight design with 2 aluminum swing doors, 50/30 mm thick, with 4 swivel rod locking mechanisms, attached in the welded aluminum rear frame in Teflon and stainless steel bearings, moving aluminum side wall suspended on the reinforced aluminum upper belt with "Kevlar liner for complete emptying, lateral brush seal and additional Kevlar liner on the side, integrated discharge chute with foldable cover plate in the floor end, operable from the outside, left rear, viewing window at the rear left, 1 sample slide in the rear doors, thus 2 pieces, service door at the front left Hydraulic System "Cargo Floor sliding floor system in the floor with hydraulically moved aluminum profiles on aluminum square profiles with approx. 670 PE-HD gliders, approx. 6mm floor thickness, hydraulics with approx. 200 mm working stroke, fixed mountings on the front wall, separate possibility for connecting the hydraulic line under the vehicle with fixed mountings, line size NW 21, fixed mountings with a size and design to be specified, operating pressure 190 max. 240 bar, aluminum end pieces welded into the floor, electrical operation at the rear left with cable operatio

Condition: used, overall weight: 39,000 kg, axle configuration: 3 axles, first registration: 11/2024, next inspection (TÜV): 11/2025, Equipment: ABS, Schmitz Cargobull SKI 24 SL 10.5 Scrap Tipper * RENTAL * Scrap tipper 55.5 m3 * SCB axles * Portal doors * Air suspension * Air steering * Lift axle * Roll-up tarpaulin * 3 cross braces for stability * Boost pressure gauge * Automatic lowering during tipping * ISO air connections with red and yellow coupling heads * 2 x 7-pin power connectors * 15-pin power connectors * ABS connection * Platform on the front wall * Folding underrun protection * Disc brakes * LED lights Rental possible! Subject to prior sale and errors! Redpsv Ttx Ujfx Ap Decf Sold exclusively subject to our terms and conditions. Important notice? Important information: Despite careful review of all details in our offer, errors may occur. These errors are sometimes caused by transmission errors in the systems of the various platform providers. Therefore, we would like to point out that all information is provided without guarantee and does not constitute a legal claim. Legal information: This sales advertisement does not constitute an offer within the meaning of Section 145 of the German Civil Code (BGB). Rather, it is information for the purpose of contract initiation. The information provided here is provided without guarantee and therefore does not represent any guaranteed properties.

Condition: used, maximum load weight: 33,707 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 09/2025, next inspection (TÜV): 09/2026, loading space length: 8,912 mm, loading space width: 2,400 mm, loading space height: 2,285 mm, loading space volume: 50 m³, total width: 2,550 mm, total height: 3,672 mm, Year of construction: 2025, Equipment: ABS, STAS 3-Axle Hardox Steel Tipper 50 cbm "EXTREME" Rock Tipper First registration: 09/2025, Condition: NEW Internal dimensions (LxWxH): 8,912 x 2,350/2,450 x 2,285 mm (tapered width design) Unladen weight: 8,293 kg Z-chassis, cranked design Continuous floor in 6 mm Hardox steel HB450 4 crusher bars evenly distributed along the entire length of the floor, fully welded Front wall and side walls made of 5 mm Hardox steel HB450 Slanted front wall, with internal access Deflector plates along the entire length of the side walls (to protect the mudguards) Hydraulic rear tailgate (with swinging function) HYVA tipping cylinder, type Alpha, suitable for high and low pressure Aluminium landing legs, full-load rated 2x pneumatic vibrators underneath the body SAF axles with large disc brakes, 430 mm 1st axle is a lift axle with start-assist WABCO Trailer EBS with roll stability support (RSS) WABCO Smartboard Automatic tipping lowering device Lifting and lowering device Rcodpfexriu Esx Ap Def Tyres: 385/65 R 22.5 Aluminium access ladder Shovel and broom holder Toolbox on the right side 4x LED reversing lights RENTING is the new BUYING: also available for immediate full-service rental-----

Condition: new, axle configuration: 3 axles, loading space volume: 55 m³, total length: 10,520 mm, total width: 2,300 mm, total height: 3,990 mm, suspension: air, tire size: 385/65-22,5, color: green, Year of construction: 2026, Equipment: ABS, - EBS Brand new at PAVIC. Available immediately! PAVIC 3-axle 55m³ tipping trailer with lift axle Technical specifications: Coupling height: 1250 mm Length: approx. 10,522 mm Width: approx. 2,300 mm Height: approx. 2,380 mm Technical axle group load capacity: 27,000 kg Technical kingpin load capacity: 12,000 kg Unladen weight: 8,520 kg CHASSIS: Heavy-duty and extra-durable I-beam main frame; manufactured from high-strength MC700 steel, welded using an automatic robotic welding process. BODY: Capacity: 55 m³ Floor plate: HARDOX450, thickness 5 mm Side walls: HARDOX450, thickness 4 mm Front wall: HARDOX450, thickness 4 mm Rear door: HARDOX450, thickness 4 mm A resonator/vibrator is installed under the structure at the front to help loosen stuck bulk materials when tipped (see pictures). TIPPER BODY: Tipping body with hydraulic tailgate. Suitable for agriculture, forestry, recycling (scrap), and more. HYDRAULIC CYLINDER (LIFT): Heavy-duty hydraulic cylinder (brand HYVA – C), single-circuit AXLES: 3 × 9-ton SAF CD (BI9–22S) axles with disc brakes (SBS2220) SUSPENSION: Air suspension. LIFT AXLE: Automatic lift axle on the 1st axle. TYRES: 6 × 385/65R22.5 (premium brand tires) WHEELS: 6 × steel rims BRAKE SYSTEM: WABCO braking system 2-line brake system according to EU regulations EBS 2S/2M Pneumatic parking brake 1 × yellow air coupling 1 × red air coupling 1 × brake pressure valve TPMS (tire pressure monitoring system) KINGPIN: 1 position, 2” (brand JOST or SAF) LANDING LEGS: Mechanical aluminum landing legs. Each leg is operated via its own locking device (after coupling). ELECTRICAL SYSTEM: Voltage: 24 V 2 × 7-pin and 1 × 15-pin ISO connectors EEC-compliant lighting as standard: SAE tail lights Side marker lights Brake warning lights Rear signal lights Lighting ASPÖCK (EUROPOINT III): 2 combination tail/brake lights (red) 2 combination indicator lights (orange) 1 license plate light ACCESSORIES: 6 × mudguards 2 × mud flaps 2 × reflective tapes and reflective plates, rear and side 1 × rear underrun protection 2 × wheel chocks with holders 1 × side aluminum protection 1 × toolbox 1 × working platform (painted and bolted) 1 × rollable tarpaulin (including mechanical support bar) PAINTWORK: Before painting, surfaces are smoothed and then cleaned. Then: sandblasting according to SA 2.5, followed by: 2 coats of primer 2 coats of acrylic topcoat RAL colors: Rjdpfxjy N Tngs Ap Djcf Chassis (KTL): black Body: green (similar to RAL 6016 yellow green) For further inquiries, our sales team will be happy to assist you. This is a non-binding offer. Subject to prior sale, errors, and changes. General information Year of manufacture: 2026 Axle configuration Tire size: 385/65-22.5 Brakes: disc brakes Suspension: air suspension...

Condition: new, maximum load weight: 29,773 kg, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 9,807 mm, loading space width: 2,440 mm, loading space height: 2,200 mm, loading space volume: 52 m³, total width: 2,550 mm, total height: 3,900 mm, Year of construction: 2025, Equipment: ABS, * Aluminum box body with combination door * Grain conveyor * Automatic level adjustment * Toolbox * Liftable first axle * Platform with ladder * Roll-up cover * Underrun protection * Wabco SmartBoard * Schmitz axles with disc brakes -----* Tire size: 385/65R22.5 * Technical total weight: 39000 kg * Permissible vertical load: 12000 kg * Tare weight: 6227 kg * Overall length: 11060 mm * Inspection due: New vehicle ----Vehicle number: 11770----Errors and prior sale excepted----Advertisements and various inscriptions have been digitally removed.-----We are happy to assist you with all the formalities involved in purchasing a vehicle. Just let us know your wishes and suggestions, and we will take care of them. Among other things, we can offer you the following services for an additional charge:----* Trade-in of your old vehicle * TÜV/SP inspection * Complete export processing * Arranging financing * Applying for export license plates Rcodpfx Apeyc Rhcs Def * Vehicle transport * Vehicle registration * Recovery and vehicle transport ----?YOUR VTS TEAM

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 6,750 kg, maximum load weight: 32,250 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 9,950 mm, loading space width: 2,480 mm, loading space height: 2,150 mm, loading space volume: 50 m³, total length: 10,300 mm, total width: 2,550 mm, total height: 3,670 mm, suspension: air, tire size: 385/65 R 22,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Rcjdpfx Aoi Rizfep Dsf More information Chassis, Saddle, Tipper Fine-grained steel welded construction, in basic lightweight design, saddle plate with interchangeable 2 kingpin Curved front end, patented 24 ton, 2-speed support winch, single-sided operation, with straight lower part, without thrust compensation Wheel chocks with holder Underrun protection, foldable Half-shell fenders Integrated fender holder, surface designed to repel stones Tarp rod with holder Towing hook at the rear Axles + Suspension BPW disc brake axles with 430 mm disc diameter Axle/suspension laser-aligned to reduce tire wear and fuel consumption Air suspension 1st axle, automatic lift axle, including forced lowering and start-up assistance Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking system 2-line compressed air braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With raising and lowering valve Vehicle - driving stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver "TPMS" tire pressure monitoring system according to ECE R 141, display via display in the towing vehicle, via EBS, without truck installation (this must be available in the truck. Only on standard tires). Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides Yellow LED lighting on the sides, linked to the turn signal ("flashing side lights") 2 x 7-pole fail-safe sockets at the front, without connecting cable Hydraulics Low-pressure cylinder, max. 170 bar, smallest stage hard-chromed, with HDK screw-on fitting, fixed part, NW 48 mm (without hose connection) Operation via truck auxiliary drive Body Steel side body made of highly wear-resistant HB 400 steel, sloping front wall with externally mounted hydraulic cylinder mount. Shovel and broom holder on the outside of the front wall. Internal access ladder on the front wall. Side walls continuously 3 mm thick, floor continuously 3 mm thick Membrane - rear wall Internal width at the bottom approx. 1440 mm Aluminum rear wall, pendulum-mounted with "double-hinge hinge" and with 2-wing door, split 1/2 to 1/2, at the top with pivoting boom, each with a grain slide per door. Standing platform with access ladder, connection plate for air/electricity and brake with large space for optimal operation. Roller cover on one side for placement on the right side, with central locking on the left side Country of approval/signs Germany Type approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for license plate holder, single-line Warning sign according to ECE - 70 Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paint Frame: DB 7350 Novagrau "10-year warranty against rust-through" Body: RAL, single color, according to customer's choice Roller cover: RAL 7035 light gray

Condition: new, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 8,500 mm, loading space width: 2,480 mm, loading space height: 1,900 mm, loading space volume: 40 m³, Equipment: ABS, Tipping semi-trailer, ALUMINIUM chassis, Jost axle units 22.5" / off road, 3x9 tons with air suspension, 1st axle lift with starting aid and electric actuation, lifting and lowering valve for air suspension, Wabco Smartboard, brake wear indicator, 6 wheels with tyres size 385 / 65 R22.5 on STEEL, 2" kingpin screwed into a steel frame. Lowering valve for air suspension, Wabco Smartboard, brake wear indicator, 6 wheels with size 385 / 65 R22.5 tires on STEEL, 2" kingpin screwed into a 10 mm thick plate, mech. version of the seat posts with one-sided operation, brake system according to E.E.G. standard, Westinghouse two-line system, spring accumulator acting on two axles and EBS -E system Wabco with RSS system (Roll-Stability-Support), aluminum air reservoir, electrical system according to STVZO with 2 five-chamber lights type Aspöck, 24 volt system, aluminum body, Edbro hydraulics with approx. 2 m hydraulic hose, 6 PVC mudguards with rubber mud flaps, side collision protection, underride protection, walkway on the frame, fully welded, LL rubber seal, spindle locks on the rear door, preparation for floor vibrator, mud-tight! FURTHER EQUIPMENT CAN ALSO BE ORDERED ON REQUEST Rcedpsu Dvw Ejfx Ap Djf COLOR FREELY SELECTABLE +590¤ Transfer costs *Pictures and offers are subject to change*

Condition: used, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 10/2023, next inspection (TÜV): 09/2026, loading space length: 10,149 mm, loading space width: 2,325 mm, loading space height: 2,285 mm, loading space volume: 55 m³, Year of construction: 2023, Equipment: ABS, ferroSTAR 54.9 cbm iron gray Chassis type: Z-chassis Axle distance (mm): 1310-1310 Fifth wheel height (mm): 1150 Chassis width (mm): 1400 Loading width (mm): 2325 Technically permissible total weight: 39 = 12 + 9 + 9 + 9 Interior height front (mm) (IHF): 2285 Interior height rear (mm) (IHB): 2285 Volume (m³): 54.9 Overall width (mm): 2550 Wheelbase (mm) (WB): 6600 Overall length (mm): 11520.836 Chassis material: Steel Tire dimension: 385/65R22.5 Loading length (mm): 10149 Axle manufacturer: SAF Axle version: Intra Brake version: Disc brake Brake type: SAF - SBS 2220 Offset (ET): 120 Option 1: Axle with lift axle and starting aid Activation of starting aid: via button in the truck (installation of the button is not included in the scope of supply) and by pressing the brake pedal three times Air suspension: ECAS with lifting and lowering valve Lowering of air suspension: Automatic lowering of the air suspension during tilting, can be manually locked via the Smartboard, as well as a switch on the chassis Coupling head: Pneumatic, European Palm coupling Tire brand: Manufacturer's choice Rims: Steel Tire type: Regional Wheel nuts: Open Wheel nut caps: Plastic Outrigger supports: Aluminum drop-leg supports, mounted at the front of the chassis, with individual operation on both sides, supporting force 20t / pair Operation of underride protection: Manual Position of Smartboard: On the left side, in the direction of travel, in front of the axles Toolbox: On the left side, in the direction of travel, in front of the axles Spare wheel holder: On the right side, in the direction of travel, below the chassis Number of splash guards on the fender: 2 pieces Type of splash guard on the fender: Clear Pass Manufacturer of lighting: Aspöck Type of lighting: ECOLED II Work lights (operated via switch): Included Position of work lights (operated via switch): 2 LED reversing lights at the rear, on the left and right in the direction of travel, mounted on the lamp carrier Position of work lights (operated via switch): 2 LED reversing lights at the front, on the left and right in the direction of travel, mounted in the area of the outrigger supports Manufacturer of tilting cylinder: Hyva (STAS manufacturer's choice) Type of tilting cylinder: Hydraulic cylinder with small housing Cylinder tilting angle: Normal Model of tilting cylinder: Hyva - FC 169 Stroke of tilting cylinder: 7130 Hydraulic coupling: Swivel coupling Hydraulic coupling - Size: 1 Hydraulic coupling - Gender: Female Hydraulic coupling - Hose: 2,100 mm Type of Smartboard: ECAS control box Aluminum ladder: With 2.8 m length, mounted on the right in the direction of travel Broom and shovel holder: Included Position of broom and shovel holder: With 3 holders each, mounted on the chassis on the left in the direction of travel Position of broom and shovel holder: On the front wall, on the left in the direction of travel Load manometer: Ø 63 mm - mounted on the side of the instrument panel Splash guard for underride protection: Black with STAS logo, mounted across the entire width of the underride protection Mounting of splash guard for underride protection: Flexible Plastic support wedges: With two plastic support wedges including holder Air and electrical console: Mounted on the right in the direction of travel Rear wall type: Swing doors A-sign: Foldable on the rear wall, mounted on the right in the direction of travel Floor: Made of 6 mm HB450 Position of rubber supports: Mounted below the floor Redpfxjzmcn Uo Ap Djcf

Condition: new, maximum load weight: 30,050 kg, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 9,664 mm, loading space width: 2,475 mm, loading space height: 2,165 mm, loading space volume: 52 m³, Year of construction: 2025, Brake system: * Wabco EBS-E (electronic braking system with RSS) * Emergency release device for spring brake cylinders * Disc brakes * Brake pad wear indicator (not connected) ----Axles: * 3 x 9 t SAF axles * 1st and 3rd axles are automatic lift axles controlled via the EBS-E system ----Suspension: * Air suspension with lift and lower system (automatic lowering during tipping operation—can be manually locked via SmartBoard—as well as via switch on chassis) ----Electrics / Lighting: * Tire pressure monitoring system (Wabco Trailerpulse) * Wabco Smart-Board * Starting aid is activated via button in the truck—no truck-side installation required—as well as by pressing the brake pedal three times * 2 x 7-pole and 1 x 15-pole sockets * Aspöck LED lighting * 2 LED reversing lights (controlled by reverse gear) * Each side in the area of the landing gear supports has 1 LED work light ----General Attachments: * Aluminum air tank Rcodpfx Apjwgg Uzj Dof * Weweler hand-crank landing gear * Side underrun protection * Folding underrun guard with handle * Speedline Diamond aluminum rims * 1 x plastic toolbox approx. 860 x 520 x 500 mm on the left side * Air gun with 16 m hose reel in the toolbox * Enclosed single plastic mudguards * 1 dust bag including mount on the right side * 3 m aluminum ladder stored on the right above the mudguards * Shovel and broom holder on the left above the mudguards * Load pressure gauge mounted at the front of the chassis * Access stairs and standing platform mounted on the front of the frame ----Chassis: * Aluminum chassis frame ----Tipping Body: * Aluminum rear tipping body—rectangular—with smooth side walls * Hyva hydraulic ram, 250 bar * Straight 4 mm aluminum front wall * Steps mounted inside the tipper body on the front wall, left side * Smooth inner and outer side walls * Double-walled 600 mm side wall profiles—30 mm thick—3 mm inner and 2 mm outer layer * Side wall profiles are fully welded inside, 90° corners using an angle profile between floor and side walls, allowing for full floor width utilization * Top rail, 90 mm wide * 6 mm wear-resistant aluminum floor in 110 Brinell quality * Combination double-wing rear doors—straight version with double door hinge and reinforcement profiles, each with 1 grain chute and all-round rubber seal * When opened, the doors are secured with chains, allowing the doors to lie as flat as possible against the side walls * 4-position door locking hooks at the bottom open automatically during tipping—can be pneumatically locked via valve on the frame ----Roll tarp: * Roll tarp—in RAL 9005 deep black—with three side tension straps * Trapezoidal tarp support, 150 mm high, on front wall and tailgate ----Load volume: * Load volume 51.8 m³ ----Fifth-wheel height: * Fifth-wheel height 1,150 mm ----Information: * Body and chassis painted with acrylic paint in RAL 9005 deep black * --Technically permissible gross weight of 39,000 kg-- * New vehicle without first registration with manufacturer warranty * Subject to prior sale and errors ----Delivery time: * Immediately available ex Egestorf

Condition: new, maximum load weight: 30,060 kg, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 7,410 mm, loading space width: 2,346 mm, loading space height: 1,515 mm, loading space volume: 26 m³, total width: 2,550 mm, total height: 2,980 mm, Year of construction: 2026, Equipment: ABS, Wielton Strong Master Hardox steel tipper body with a 26 m³ loading volume HP tipper body Immediately available 30 Years Black Edition Overlapping oscillating tailgate with grain slide New vehicle, immediately available! Unladen weight approx. 5,940 kg Equipment: - SAF disc axles - Axle lift with control line - Automatic tilting lowering - JOST geared landing gears, full load - WABCO braking system - Semi-circular Hardox tipper body Rcedpjzctmhsfx Ap Def - Overlapping oscillating tailgate with lateral tension locks - Grain slide in the center + additional rotating locks - Double pendulum bearing and replaceable rubber seal - Floor 4 mm / side wall 3 mm - Roller cover with quick-release fastener - Operating platform on the frame - Hyva 250 bar hydraulic cylinders - Tires 385/65 R22.5 Hankook TH31 - Aluminum rims ABERG - Rear lights, full LED Aspöck - 2x LED reversing lights - Tool box - Water tank - Shovel + broom - Aluminum ladder Subject to prior sale and errors in this offer. Only the agreements in the order confirmation or the purchase contract are binding. You will receive the exact scope of equipment and prices from our sales staff. Please contact us.