Low loader trailer

Humbaur HTD 30 3 Achs Tiefladeranhänger, Wenig Benutzt

Condition: new, maximum load weight: 31,630 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,250 mm, loading space width: 2,520 mm, * T 4: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Parabolic springs * Mechanical axle equalization front and rear * Tire pressure monitoring with display functionality in the truck via EBS signal (no truck-side installation required) * Warning sign packages front & rear * Reflective contour markings on the sides and rear * EBS multi-voltage system for 12 & 24 V electrics * Removable LED beacon at rear * 24 V 15-pin power cable, additionally 12 V 7+4 pin power cable * Extended connection cables for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm towing eye and infinitely adjustable height * Powder-coated steel toolbox and basket-type spare wheel holder mounted on the right side * Closed single plastic mudguard at the front * Straight rear steel spray suppression mudguards, including spray suppression * Side underrun protection * Extended offset bend, 500 mm forward * Turntable platform extension, 520 mm with 45° corners and 3 recessed, lockable storage compartments with lids Bedpfxjrczm De Abzocw * Chassis made of high-tensile fine-grain steel * Deck over turntable platform: 50 mm softwood, low-bed platform: 60 mm softwood * Outer boards of ramps: 50 mm bamboo * 4 stake pockets per side (stakes not included), double as 2 t lashing points * Load securing package includes: 2 lashing eyes (6.4 t) front left & right on main frame of turntable platform; 1 pair each side front & rear (13.4 t) lashing rings on outer frame; 4 pairs per side (10 t) swingable/drop-down multi-directional lashing rings inlet into outer frame; 2 pairs (6.4 t) on excavator arm support; 8 pairs galvanized folding widening brackets for up to 3 m overall width (not in rear slope) * Widening timbers stored in lateral compartment on left side * Excavator arm support above rear axle to end of drive-on slope approx. 2,300 x 740 x 190 mm * Mechanical rear drop-down support legs * Hydraulic, hot-dip galvanized ramps approx. 3,000 x 720 mm * Hydraulic lateral ramp shift via sliding tube on ramp shaft * Deck above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Loading height loaded: approx. 860 mm (including 860 mm drive-on slope) * Chassis, turntable, ramps, rear mechanical drop-down supports are hot-dip galvanized * Axles, springs, air tanks, and turntable painted in black * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Available from KW 21 / 2026

Condition: used, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 07/2024, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 profile: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 tonne Gigant axles * Air suspension with lifting and lowering system and RtR valve * Manometer pressure indicator for determining load weight (axles separated into 2 air suspension circuits) * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fender with splash guard * Rear straight galvanized. Sheet steel aprons with splash guard * Reflective contour tape on the side and rear * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power plug Bjdpfx Abel Tlhrjzscw * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) * Pull scissors with 50 mm pull eye and height adjustment * Tool box made of galvanized sheet steel, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high * Front section in front of the bogie platform approx. 490 mm long with 45° corners * ROBOT welded ANTI-SLIP coating for the steel plate of the bogie platform * La-Si package consisting of: in front of the front wall support on the left & right 1 x 13.4 ton each. UVV lashing eye, 4 holes on each side in the bogie platform with a lashing force of 2 tons each, 1 pair of lashing eyes (13.4 tons) hanging at the rear left and right in front of the rear carrier, 4 pairs of UVV lashing rings (10 tons) on each side, can be swiveled and lowered, can be loaded in all directions and embedded in the outer frame, 3 stake pockets on each side with a simultaneous 2 ton lashing option * Hot-dip galvanized mechanical folding boom for a total width of 3 meters (but not in the rear slope) * Plank holder for widening under the chassis on the left in the longitudinal direction * Excavator boom storage above the rear axle to the end carrier approx. 2,100 mm long and approx. 190 mm deep, 2 pairs of 6.4 tons on each side. Lashing rings in the excavator boom storage * Hardwood floor on the running surfaces of the low-loading platform * Hydraulic one-piece ramps (approx. 3,000 x 720 mm) mechanically laterally adjustable * Outer planks of the ramps made of hardwood * Steel construction in preparation for 6-way control slide * Loading edge unloaded approx. 950 mm +/+ 20 mm chassis * Bogie, folding boom, mechanical drop supports, ramps hot-dip galvanized * --Axles, air tank, pull scissors painted in a black tone-- * Tires 235/75 R 17.5 * Vehicle has a daily registration in 07/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: used, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 07/2024, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 profile: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 tonne Gigant axles Bodpol Tnu Aefx Abzecw * Air suspension with lifting and lowering system and RtR valve * Manometer pressure indicator for determining load weight (axles separated into 2 air suspension circuits) * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fender with splash guard * Rear straight galvanized. Sheet steel aprons with splash guard * Reflective contour tape on the side and rear * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power plug * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) * Pull scissors with 50 mm pull eye and height adjustment * Tool box made of galvanized sheet steel, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high * Front section in front of the bogie platform approx. 490 mm long with 45° corners * ROBOT welded ANTI-SLIP coating for the steel plate of the bogie platform * La-Si package consisting of: in front of the front wall support on the left & right 1 x 13.4 ton each. UVV lashing eye, 4 holes on each side in the bogie platform with a lashing force of 2 tons each, 1 pair of lashing eyes (13.4 tons) hanging at the rear left and right in front of the rear carrier, 4 pairs of UVV lashing rings (10 tons) on each side, can be swiveled and lowered, can be loaded in all directions and embedded in the outer frame, 3 stake pockets on each side with a simultaneous 2 ton lashing option * Hot-dip galvanized mechanical folding boom for a total width of 3 meters (but not in the rear slope) * Plank holder for widening under the chassis on the left in the longitudinal direction * Excavator boom storage above the rear axle to the end carrier approx. 2,100 mm long and approx. 190 mm deep, 2 pairs of 6.4 tons on each side. Lashing rings in the excavator boom storage * Hardwood floor on the running surfaces of the low-loading platform * Hydraulic one-piece ramps (approx. 3,000 x 720 mm) mechanically laterally adjustable * Outer planks of the ramps made of hardwood * Steel construction in preparation for 6-way control slide * Loading edge unloaded approx. 950 mm +/+ 20 mm chassis * Bogie, folding boom, mechanical drop supports, ramps hot-dip galvanized * --Axles, air tank, pull scissors painted in a black tone-- * Tires 235/75 R 17.5 * Vehicle has a daily registration in 07/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf