Lowbed

Fliegl DTS S 300 Parab/Feder

Additional information
Low-loader chassis
Steel welded construction
Turntable with heavy-duty ball bearing
Foldable rear support
2 wheel chocks with holder
Aluminum side impact protection
Splash guards at the rear, covering the entire width
Partial fender, 1st axle with anti-splash guard, anti-splash guard behind the 2nd and 3rd axle
1 plastic toolbox with insert, w=620/h=360/d=440 mm, lockable with a padlock. (Lock not included)
Extendable widening sections to 3,000 mm
Storage compartment for timber planks in the center of the loading area
Timber planks, 70 mm for widening to 3000 mm
Tie-down points for low-loader (40 tie-down points)
1 pair of tie-down recesses in the longitudinal beam at the front, recessed in the outrigger, each 10 tons.
4 pairs of tie-down holes in the outer frame, each 5 tons (for attaching lashing straps)
7 pairs of tie-down eyes recessed on top and on the side of the outer frame, each 10 tons
1 x at the front on the outrigger
6 x in the low bed
First tie-down point 250 mm from the front and last max. 250 mm from the rear, distance between tie-down points not greater than 1100 mm
5 pairs of pocket recesses in the outer frame, inside 70 x 40 mm (can be converted to 5-ton ring tie-down points, not included)
2 pairs of folding tie-down points additionally, each 10 tons
1 x on the outrigger (protrudes)
1 x behind the last axle, recessed in the floor
Coupling device, low-loader turntable
Drawbar with tested 40 mm drawbar eye
Axles + Suspension
Drum brake axles, as per manufacturer's choice
Laser-measured axle/suspension to reduce tire wear and fuel consumption
Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (lever compensation)
Wheels and tires
235 / 75 R 17.5
As per manufacturer's choice
Steel rims in twin configuration, factory silver
Braking system
2-line pneumatic braking system
Spring-loaded parking brake
2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle
ABS and ALB, with ABS connector at the front, with connection cable
Manufacturer: Wabco or Knorr
Electrical system
24 Volt, multi-chamber lights, yellow LED lighting on the sides
2 white position lights at the front
2 white/red marker lights at the rear
2 x 7-pole fail-safe plugs at the front, with connection cable
Lsdpfx Anoi Ri Dde Ijhh
1 LED rotating beacon with holder, switched via parking lights (beacon removable)
2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm
Floor
Outrigger at the front with steel/diamond plate covering
Storage box recessed in the transition slope to the outrigger
Then with 70 mm soft wood floor, in the wheel arch area steel/diamond plate covering
Rear slope with 70 mm soft wood floor
Low-loader platform including rear slope 6,500 mm
Ramps
Steel ramps 2,800 mm long, 750 mm wide, can be shifted sideways
Covered with wood
With spring-loaded support
Country of registration/signs
Country of registration: Germany
24/7 service hotline
Prepared for license plate holder, two lines
Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear
Warning sign according to ECE - 70
Paint finish
Frame hot-dip galvanized including passivation
15 years warranty against rust-through
Drawbar galvanized or black, as per manufacturer's choice
Ramps hot-dip galvanized
Attention! These are archive images!

The listing was translated automatically. Translation errors are possible.