Volvo FH 6x4 R with wood chip tipper trailer

Volvo FH6x4R Volvo FH6x4R & Anhänger Hackgutkipper Ne

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 7,200 kg, maximum load weight: 27,800 kg, overall weight: 35,000 kg, axle configuration: 3 axles, total length: 13,850 mm, total width: 2,550 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, Custom-Made Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Chassis, Saddle, and Haulage Company Fine-grained steel welded construction in lightweight design, saddle plate with interchangeable 2 kingpins, main frame reinforcement for 25 tons, with center of gravity at 3 m load length in the retracted state. 13 pairs of hooks for securing lashing straps, welded onto the crossbeams 23 pairs of lashing eyes recessed into the outer frame, each 3.5 tons Outer frame with Load-Lock profile for attaching lashing straps Note! Not usable with sideboards! 24 tons, 2-speed support winch in reinforced design for loaded coupling/uncoupling, single-sided operation Chocks with holder Aluminum side impact protection Under-run protection Half-shell fenders with anti-splash flaps according to EC 1 spare wheel holder for 1 tire, with wheel fastening kit 1 closed storage box for stakes, open at the top, below the loading area, doors on both sides, w=450 mm/h=400/420 mm/d=2460 mm 6 pairs of pull-out stake pockets, for rectangular section stakes 80x80 mm, extendable from loading width of 2000 mm to 3100 mm 4 pairs of stake pockets recessed into the outer frame, for rectangular section stakes 80x80 mm 11 stake pockets recessed in the center of the floor, for rectangular section stakes 80x80 mm, with reinforcement beam, installed between the outer stake pockets 5 x 3 pairs of stake pockets recessed into the outer longitudinal beams, for rectangular section stakes 80x80 mm, including reinforcement beams - for load securing to the front and rear during the transport of reinforcing steel mats, 2x5000 mm or 2x 6000 mm 6 lightweight plug-in stakes, w=80/d=80/, usable height approx. 1850 mm, hot-dip galvanized, with rope guide at the top for strap tensioning 12 lightweight plug-in stakes, w=80/d=80/, usable height approx. 1850 mm, hot-dip galvanized, with lashing eyes welded to the bottom on both sides Note: Stake pockets/plug-in stakes are not designed for the sole securing of long materials, pipes, etc. without strapping. 2 plastic toolboxes, with drawer and insert, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) 6 steel winches with wire rope and clevis hook, with rope guide through the outer frame, 1 removable gearhead for steel winch - supplied loose Telescoping Main frame telescoping extendable by a maximum of 4,000 mm and lockable every approx. 500 mm Locking with pneumatic pin locking + indicator for frame locking on both sides, operated via hand knob, operation for brake/locking and suspension on the control panel on the left side in front of the axles Storage compartment between the longitudinal beams in the extended state Axles + Suspension SAF disc brake axles with 430 mm disc diameter Last axle with trailing arm, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand knob, as well as manually via switch in the towing vehicle (Pin 10), without truck installation. Fodpoi Ri Szefx Ab Ajpp Axle track offset mm Air suspension 1st axle automatic lift axle, additionally electrically operable from the truck, with starting aid Braking System 2-line compressed air braking system Colored line routing for easy servicing Spring brake parking brake 2 fail-safe coupling heads at the front EBS manufacturer according to the manufacturer's choice, electronic braking system with EBS