Forage wagon

Krone ZX 430 GD

Condition: used, Year of construction: 2021, operating hours: 2,011 h, Equipment: compressed air brake, ZX 430 GD Krone forage wagon + Tyres: 710/50 R 30.5 (Trac profile, 10-hole rim) + Tandem axle unit with hydraulic compensation, permissible axle load 20t + 2-line pneumatic braking system with hydraulically controlled ALB, rear axle steered, without suspension + Lower linkage with 80mm ball coupling, support load 4,000 kg + Loading space cover + Dosing unit with 3-roll series + Additional rear pick-up gauge wheels (for optimised ground contour following) + Version approved for 40 km/h at no extra cost + LED headlights incl. cable and {connector,} one included + LED headlights included (operable via terminal, wagon prepared) (for up to eight LED {work lights,}) + Set of additional knives + Basic work lighting 1.0 + ISOBUS control terminal CCI 800 In-cab Fpjdpsx R Nfdsfx Aa Rob + ISOBUS terminal CCI 800 In-cab + Hydropneumatic suspension (only possible with tandem axle unit with hydraulic compensation) Contact: Harm Otten

Condition: used, Year of construction: 2022, operating hours: 515 h, Equipment: crop cutter, ZX 430 GD Krone Loading Wagon 2025801 ZX 430 GD TT_0297 Tyres: 800/45 R 26.5 TL 174 D 10-hole TT_3968 Tandem, equal, steered, DLB+ALB TT_0550 Basic loading automation TT_0655 Lower hitch K80 ball coupling TT_1403 Dosing unit / 3 rollers TT_0810 Drawbar suspension TT_0710 Knife sharpening device TT_1220 Additional rear tracking wheels TT_1310 Cargo area cover TT_3011 Comfort 1.0 B_091 Version for 40 km/h Technical Data Fsdpex R Nhrjfx Aa Repb Capacity by DIN 11741: 43 m³ Overall length: 9,845 mm Overall width: 2,980 mm Overall height: 3,950 mm Track width: 2,050 mm PTO speed: 1,000 rpm Power requirement from 155 kW (210 hp) Hitch Pivoting drawbar Hydraulic drawbar suspension Pivoting drawbar automation 1.0 for storing a loading and road position Pivoting drawbar control module 1.0 to speed up coupling and uncoupling between tractor and loader wagon Drive shaft, wide angle joint both sides, 1 3/4", Z=6, overload clutch Hydraulic system: Load-sensing Pick-up Roller crop press Pendulum suspended pick-up Electro-hydraulic pick-up relief Non-steered hydraulic pick-up EasyFlow (2,125 mm working width) Six W-shaped tine rows, 55 mm tine spacing 16x6.50-8 oscillating gauge wheels Cutting and feed rotor Rotor drive via belt and integrated planetary gearbox Cutting and feed rotor with eight tine rows, asymmetric feed plates made from Hardox steel 1,910 mm feed channel width Cutterbar with 48 knives, knife group selection Theoretical cutting length 37 / 74 mm (half knife set) Individual knife protection (adjustable sensitivity) Automatic reset of triggered knife protection Sideways swiveling knife cassette, unlockable from one side of the wagon Rotor cover (for use as forage transport wagon) Cargo area Swiveling front wall PowerLoad loading automation Lowered floor conveyor Double floor conveyor with four flat-link chains Hydraulic drive on both sides of floor conveyor Changeover valve for two conveyor speeds (fast mode), incl. fast mode automation 1.0 All-steel body, sidewalls arranged conically LED cargo area lighting (includes wiring harness and four LED strips) Access hatch Hydraulic tailgate including opening sensor and floor conveyor shut-off Dosing unit Dosing rollers and floor conveyor shut-off Direct drive dosing rollers including overrunning clutch, protected via main drive shaft Further equipment Comfort onboard electronics 1.0 ISOBUS-compatible, without control terminal